diff options
Diffstat (limited to 'arch/mips/au1000/mtx-1/board_setup.c')
-rw-r--r-- | arch/mips/au1000/mtx-1/board_setup.c | 63 |
1 files changed, 30 insertions, 33 deletions
diff --git a/arch/mips/au1000/mtx-1/board_setup.c b/arch/mips/au1000/mtx-1/board_setup.c index 5736354829c..3f8079186cf 100644 --- a/arch/mips/au1000/mtx-1/board_setup.c +++ b/arch/mips/au1000/mtx-1/board_setup.c @@ -3,9 +3,8 @@ * BRIEF MODULE DESCRIPTION * 4G Systems MTX-1 board setup. * - * Copyright 2003 MontaVista Software Inc. - * Author: MontaVista Software, Inc. - * ppopov@mvista.com or source@mvista.com + * Copyright 2003, 2008 MontaVista Software Inc. + * Author: MontaVista Software, Inc. <source@mvista.com> * Bruno Randolf <bruno.randolf@4g-systems.biz> * * This program is free software; you can redistribute it and/or modify it @@ -34,7 +33,7 @@ #include <asm/mach-au1x00/au1000.h> extern int (*board_pci_idsel)(unsigned int devsel, int assert); -int mtx1_pci_idsel(unsigned int devsel, int assert); +int mtx1_pci_idsel(unsigned int devsel, int assert); void board_reset(void) { @@ -45,36 +44,36 @@ void board_reset(void) void __init board_setup(void) { #if defined(CONFIG_USB_OHCI_HCD) || defined(CONFIG_USB_OHCI_HCD_MODULE) - // enable USB power switch - au_writel( au_readl(GPIO2_DIR) | 0x10, GPIO2_DIR ); - au_writel( 0x100000, GPIO2_OUTPUT ); + /* Enable USB power switch */ + au_writel(au_readl(GPIO2_DIR) | 0x10, GPIO2_DIR); + au_writel(0x100000, GPIO2_OUTPUT); #endif /* defined(CONFIG_USB_OHCI_HCD) || defined(CONFIG_USB_OHCI_HCD_MODULE) */ #ifdef CONFIG_PCI #if defined(__MIPSEB__) - au_writel(0xf | (2<<6) | (1<<4), Au1500_PCI_CFG); + au_writel(0xf | (2 << 6) | (1 << 4), Au1500_PCI_CFG); #else au_writel(0xf, Au1500_PCI_CFG); #endif #endif - // initialize sys_pinfunc: - au_writel( SYS_PF_NI2, SYS_PINFUNC ); + /* Initialize sys_pinfunc */ + au_writel(SYS_PF_NI2, SYS_PINFUNC); - // initialize GPIO - au_writel( 0xFFFFFFFF, SYS_TRIOUTCLR ); - au_writel( 0x00000001, SYS_OUTPUTCLR ); // set M66EN (PCI 66MHz) to OFF - au_writel( 0x00000008, SYS_OUTPUTSET ); // set PCI CLKRUN# to OFF - au_writel( 0x00000002, SYS_OUTPUTSET ); // set EXT_IO3 ON - au_writel( 0x00000020, SYS_OUTPUTCLR ); // set eth PHY TX_ER to OFF + /* Initialize GPIO */ + au_writel(0xFFFFFFFF, SYS_TRIOUTCLR); + au_writel(0x00000001, SYS_OUTPUTCLR); /* set M66EN (PCI 66MHz) to OFF */ + au_writel(0x00000008, SYS_OUTPUTSET); /* set PCI CLKRUN# to OFF */ + au_writel(0x00000002, SYS_OUTPUTSET); /* set EXT_IO3 ON */ + au_writel(0x00000020, SYS_OUTPUTCLR); /* set eth PHY TX_ER to OFF */ - // enable LED and set it to green - au_writel( au_readl(GPIO2_DIR) | 0x1800, GPIO2_DIR ); - au_writel( 0x18000800, GPIO2_OUTPUT ); + /* Enable LED and set it to green */ + au_writel(au_readl(GPIO2_DIR) | 0x1800, GPIO2_DIR); + au_writel(0x18000800, GPIO2_OUTPUT); board_pci_idsel = mtx1_pci_idsel; - printk("4G Systems MTX-1 Board\n"); + printk(KERN_INFO "4G Systems MTX-1 Board\n"); } int @@ -82,20 +81,18 @@ mtx1_pci_idsel(unsigned int devsel, int assert) { #define MTX_IDSEL_ONLY_0_AND_3 0 #if MTX_IDSEL_ONLY_0_AND_3 - if (devsel != 0 && devsel != 3) { - printk("*** not 0 or 3\n"); - return 0; - } + if (devsel != 0 && devsel != 3) { + printk(KERN_ERR "*** not 0 or 3\n"); + return 0; + } #endif - if (assert && devsel != 0) { - // suppress signal to cardbus - au_writel( 0x00000002, SYS_OUTPUTCLR ); // set EXT_IO3 OFF - } - else { - au_writel( 0x00000002, SYS_OUTPUTSET ); // set EXT_IO3 ON - } - au_sync_udelay(1); - return 1; + if (assert && devsel != 0) + /* Suppress signal to Cardbus */ + au_writel(0x00000002, SYS_OUTPUTCLR); /* set EXT_IO3 OFF */ + else + au_writel(0x00000002, SYS_OUTPUTSET); /* set EXT_IO3 ON */ + au_sync_udelay(1); + return 1; } |