diff options
Diffstat (limited to 'Documentation/devicetree')
3 files changed, 213 insertions, 0 deletions
diff --git a/Documentation/devicetree/bindings/pinctrl/lantiq,falcon-pinumx.txt b/Documentation/devicetree/bindings/pinctrl/lantiq,falcon-pinumx.txt new file mode 100644 index 000000000000..daa768956069 --- /dev/null +++ b/Documentation/devicetree/bindings/pinctrl/lantiq,falcon-pinumx.txt @@ -0,0 +1,83 @@ +Lantiq FALCON pinmux controller + +Required properties: +- compatible: "lantiq,pinctrl-falcon" +- reg: Should contain the physical address and length of the gpio/pinmux + register range + +Please refer to pinctrl-bindings.txt in this directory for details of the +common pinctrl bindings used by client devices, including the meaning of the +phrase "pin configuration node". + +Lantiq's pin configuration nodes act as a container for an abitrary number of +subnodes. Each of these subnodes represents some desired configuration for a +pin, a group, or a list of pins or groups. This configuration can include the +mux function to select on those group(s), and two pin configuration parameters: +pull-up and open-drain + +The name of each subnode is not important as long as it is unique; all subnodes +should be enumerated and processed purely based on their content. + +Each subnode only affects those parameters that are explicitly listed. In +other words, a subnode that lists a mux function but no pin configuration +parameters implies no information about any pin configuration parameters. +Similarly, a pin subnode that describes a pullup parameter implies no +information about e.g. the mux function. + +We support 2 types of nodes. + +Definition of mux function groups: + +Required subnode-properties: +- lantiq,groups : An array of strings. Each string contains the name of a group. + Valid values for these names are listed below. +- lantiq,function: A string containing the name of the function to mux to the + group. Valid values for function names are listed below. + +Valid values for group and function names: + + mux groups: + por, ntr, ntr8k, hrst, mdio, bootled, asc0, spi, spi cs0, spi cs1, i2c, + jtag, slic, pcm, asc1 + + functions: + rst, ntr, mdio, led, asc, spi, i2c, jtag, slic, pcm + + +Definition of pin configurations: + +Required subnode-properties: +- lantiq,pins : An array of strings. Each string contains the name of a pin. + Valid values for these names are listed below. + +Optional subnode-properties: +- lantiq,pull: Integer, representing the pull-down/up to apply to the pin. + 0: none, 1: down +- lantiq,drive-current: Boolean, enables drive-current +- lantiq,slew-rate: Boolean, enables slew-rate + +Example: + pinmux0 { + compatible = "lantiq,pinctrl-falcon"; + pinctrl-names = "default"; + pinctrl-0 = <&state_default>; + + state_default: pinmux { + asc0 { + lantiq,groups = "asc0"; + lantiq,function = "asc"; + }; + ntr { + lantiq,groups = "ntr8k"; + lantiq,function = "ntr"; + }; + i2c { + lantiq,groups = "i2c"; + lantiq,function = "i2c"; + }; + hrst { + lantiq,groups = "hrst"; + lantiq,function = "rst"; + }; + }; + }; diff --git a/Documentation/devicetree/bindings/pinctrl/lantiq,xway-pinumx.txt b/Documentation/devicetree/bindings/pinctrl/lantiq,xway-pinumx.txt new file mode 100644 index 000000000000..b5469db1d7ad --- /dev/null +++ b/Documentation/devicetree/bindings/pinctrl/lantiq,xway-pinumx.txt @@ -0,0 +1,97 @@ +Lantiq XWAY pinmux controller + +Required properties: +- compatible: "lantiq,pinctrl-xway" or "lantiq,pinctrl-xr9" +- reg: Should contain the physical address and length of the gpio/pinmux + register range + +Please refer to pinctrl-bindings.txt in this directory for details of the +common pinctrl bindings used by client devices, including the meaning of the +phrase "pin configuration node". + +Lantiq's pin configuration nodes act as a container for an abitrary number of +subnodes. Each of these subnodes represents some desired configuration for a +pin, a group, or a list of pins or groups. This configuration can include the +mux function to select on those group(s), and two pin configuration parameters: +pull-up and open-drain + +The name of each subnode is not important as long as it is unique; all subnodes +should be enumerated and processed purely based on their content. + +Each subnode only affects those parameters that are explicitly listed. In +other words, a subnode that lists a mux function but no pin configuration +parameters implies no information about any pin configuration parameters. +Similarly, a pin subnode that describes a pullup parameter implies no +information about e.g. the mux function. + +We support 2 types of nodes. + +Definition of mux function groups: + +Required subnode-properties: +- lantiq,groups : An array of strings. Each string contains the name of a group. + Valid values for these names are listed below. +- lantiq,function: A string containing the name of the function to mux to the + group. Valid values for function names are listed below. + +Valid values for group and function names: + + mux groups: + exin0, exin1, exin2, jtag, ebu a23, ebu a24, ebu a25, ebu clk, ebu cs1, + ebu wait, nand ale, nand cs1, nand cle, spi, spi_cs1, spi_cs2, spi_cs3, + spi_cs4, spi_cs5, spi_cs6, asc0, asc0 cts rts, stp, nmi , gpt1, gpt2, + gpt3, clkout0, clkout1, clkout2, clkout3, gnt1, gnt2, gnt3, req1, req2, + req3 + + additional mux groups (XR9 only): + mdio, nand rdy, nand rd, exin3, exin4, gnt4, req4 + + functions: + spi, asc, cgu, jtag, exin, stp, gpt, nmi, pci, ebu, mdio + + + +Definition of pin configurations: + +Required subnode-properties: +- lantiq,pins : An array of strings. Each string contains the name of a pin. + Valid values for these names are listed below. + +Optional subnode-properties: +- lantiq,pull: Integer, representing the pull-down/up to apply to the pin. + 0: none, 1: down, 2: up. +- lantiq,open-drain: Boolean, enables open-drain on the defined pin. + +Valid values for XWAY pin names: + Pinconf pins can be referenced via the names io0-io31. + +Valid values for XR9 pin names: + Pinconf pins can be referenced via the names io0-io55. + +Example: + gpio: pinmux@E100B10 { + compatible = "lantiq,pinctrl-xway"; + pinctrl-names = "default"; + pinctrl-0 = <&state_default>; + + #gpio-cells = <2>; + gpio-controller; + reg = <0xE100B10 0xA0>; + + state_default: pinmux { + stp { + lantiq,groups = "stp"; + lantiq,function = "stp"; + }; + pci { + lantiq,groups = "gnt1"; + lantiq,function = "pci"; + }; + conf_out { + lantiq,pins = "io4", "io5", "io6"; /* stp */ + lantiq,open-drain; + lantiq,pull = <0>; + }; + }; + }; + diff --git a/Documentation/devicetree/bindings/spi/spi-octeon.txt b/Documentation/devicetree/bindings/spi/spi-octeon.txt new file mode 100644 index 000000000000..431add192342 --- /dev/null +++ b/Documentation/devicetree/bindings/spi/spi-octeon.txt @@ -0,0 +1,33 @@ +Cavium, Inc. OCTEON SOC SPI master controller. + +Required properties: +- compatible : "cavium,octeon-3010-spi" +- reg : The register base for the controller. +- interrupts : One interrupt, used by the controller. +- #address-cells : <1>, as required by generic SPI binding. +- #size-cells : <0>, also as required by generic SPI binding. + +Child nodes as per the generic SPI binding. + +Example: + + spi@1070000001000 { + compatible = "cavium,octeon-3010-spi"; + reg = <0x10700 0x00001000 0x0 0x100>; + interrupts = <0 58>; + #address-cells = <1>; + #size-cells = <0>; + + eeprom@0 { + compatible = "st,m95256", "atmel,at25"; + reg = <0>; + spi-max-frequency = <5000000>; + spi-cpha; + spi-cpol; + + pagesize = <64>; + size = <32768>; + address-width = <16>; + }; + }; + |