Merge git://git.kernel.org/pub/scm/linux/kernel/git/davem/net-next

* git://git.kernel.org/pub/scm/linux/kernel/git/davem/net-next: (1745 commits)
  dp83640: free packet queues on remove
  dp83640: use proper function to free transmit time stamping packets
  ipv6: Do not use routes from locally generated RAs
  |PATCH net-next] tg3: add tx_dropped counter
  be2net: don't create multiple RX/TX rings in multi channel mode
  be2net: don't create multiple TXQs in BE2
  be2net: refactor VF setup/teardown code into be_vf_setup/clear()
  be2net: add vlan/rx-mode/flow-control config to be_setup()
  net_sched: cls_flow: use skb_header_pointer()
  ipv4: avoid useless call of the function check_peer_pmtu
  TCP: remove TCP_DEBUG
  net: Fix driver name for mdio-gpio.c
  ipv4: tcp: fix TOS value in ACK messages sent from TIME_WAIT
  rtnetlink: Add missing manual netlink notification in dev_change_net_namespaces
  ipv4: fix ipsec forward performance regression
  jme: fix irq storm after suspend/resume
  route: fix ICMP redirect validation
  net: hold sock reference while processing tx timestamps
  tcp: md5: add more const attributes
  Add ethtool -g support to virtio_net
  ...

Fix up conflicts in:
 - drivers/net/Kconfig:
	The split-up generated a trivial conflict with removal of a
	stale reference to Documentation/networking/net-modules.txt.
	Remove it from the new location instead.
 - fs/sysfs/dir.c:
	Fairly nasty conflicts with the sysfs rb-tree usage, conflicting
	with Eric Biederman's changes for tagged directories.

2 files changed, 51 insertions, 50 deletions

diff --git a/Documentation/devicetree/bindings/net/can/fsl-flexcan.txt b/Documentation/devicetree/bindings/net/can/fsl-flexcan.txt
index 1a729f089866..1ad80d5865a9 100644
--- a/Documentation/devicetree/bindings/net/can/fsl-flexcan.txt
+++ b/Documentation/devicetree/bindings/net/can/fsl-flexcan.txt
@@ -1,61 +1,24 @@
-CAN Device Tree Bindings
-------------------------
-2011 Freescale Semiconductor, Inc.
+Flexcan CAN contoller on Freescale's ARM and PowerPC system-on-a-chip (SOC).
 
-fsl,flexcan-v1.0 nodes
------------------------
-In addition to the required compatible-, reg- and interrupt-properties, you can
-also specify which clock source shall be used for the controller.
+Required properties:
 
-CPI Clock- Can Protocol Interface Clock
-	This CLK_SRC bit of CTRL(control register) selects the clock source to
-	the CAN Protocol Interface(CPI) to be either the peripheral clock
-	(driven by the PLL) or the crystal oscillator clock. The selected clock
-	is the one fed to the prescaler to generate the Serial Clock (Sclock).
-	The PRESDIV field of CTRL(control register) controls a prescaler that
-	generates the Serial Clock (Sclock), whose period defines the
-	time quantum used to compose the CAN waveform.
+- compatible : Should be "fsl,<processor>-flexcan"
 
-Can Engine Clock Source
-	There are two sources for CAN clock
-	- Platform Clock  It represents the bus clock
-	- Oscillator Clock
+  An implementation should also claim any of the following compatibles
+  that it is fully backwards compatible with:
 
-	Peripheral Clock (PLL)
-	--------------
-		     |
-		    ---------		      -------------
-		    |       |CPI Clock	      | Prescaler |       Sclock
-		    |       |---------------->| (1.. 256) |------------>
-		    ---------		      -------------
-                     |  |
-	--------------  ---------------------CLK_SRC
-	Oscillator Clock
+  - fsl,p1010-flexcan
 
-- fsl,flexcan-clock-source : CAN Engine Clock Source.This property selects
-			     the peripheral clock. PLL clock is fed to the
-			     prescaler to generate the Serial Clock (Sclock).
-			     Valid values are "oscillator" and "platform"
-			     "oscillator": CAN engine clock source is oscillator clock.
-			     "platform" The CAN engine clock source is the bus clock
-		             (platform clock).
+- reg : Offset and length of the register set for this device
+- interrupts : Interrupt tuple for this device
+- clock-frequency : The oscillator frequency driving the flexcan device
 
-- fsl,flexcan-clock-divider : for the reference and system clock, an additional
-			      clock divider can be specified.
-- clock-frequency: frequency required to calculate the bitrate for FlexCAN.
+Example:
 
-Note:
-	- v1.0 of flexcan-v1.0 represent the IP block version for P1010 SOC.
-	- P1010 does not have oscillator as the Clock Source.So the default
-	  Clock Source is platform clock.
-Examples:
-
-	can0@1c000 {
-		compatible = "fsl,flexcan-v1.0";
+	can@1c000 {
+		compatible = "fsl,p1010-flexcan";
 		reg = <0x1c000 0x1000>;
 		interrupts = <48 0x2>;
 		interrupt-parent = <&mpic>;
-		fsl,flexcan-clock-source = "platform";
-		fsl,flexcan-clock-divider = <2>;
-		clock-frequency = <fixed by u-boot>;
+		clock-frequency = <200000000>; // filled in by bootloader
 	};
diff --git a/Documentation/devicetree/bindings/net/smsc911x.txt b/Documentation/devicetree/bindings/net/smsc911x.txt
new file mode 100644
index 000000000000..adb5b5744ecd
--- /dev/null
+++ b/Documentation/devicetree/bindings/net/smsc911x.txt
@@ -0,0 +1,38 @@
+* Smart Mixed-Signal Connectivity (SMSC) LAN911x/912x Controller
+
+Required properties:
+- compatible : Should be "smsc,lan<model>", "smsc,lan9115"
+- reg : Address and length of the io space for SMSC LAN
+- interrupts : Should contain SMSC LAN interrupt line
+- interrupt-parent : Should be the phandle for the interrupt controller
+  that services interrupts for this device
+- phy-mode : String, operation mode of the PHY interface.
+  Supported values are: "mii", "gmii", "sgmii", "tbi", "rmii",
+  "rgmii", "rgmii-id", "rgmii-rxid", "rgmii-txid", "rtbi", "smii".
+
+Optional properties:
+- reg-shift : Specify the quantity to shift the register offsets by
+- reg-io-width : Specify the size (in bytes) of the IO accesses that
+  should be performed on the device.  Valid value for SMSC LAN is
+  2 or 4.  If it's omitted or invalid, the size would be 2.
+- smsc,irq-active-high : Indicates the IRQ polarity is active-high
+- smsc,irq-push-pull : Indicates the IRQ type is push-pull
+- smsc,force-internal-phy : Forces SMSC LAN controller to use
+  internal PHY
+- smsc,force-external-phy : Forces SMSC LAN controller to use
+  external PHY
+- smsc,save-mac-address : Indicates that mac address needs to be saved
+  before resetting the controller
+- local-mac-address : 6 bytes, mac address
+
+Examples:
+
+lan9220@f4000000 {
+	compatible = "smsc,lan9220", "smsc,lan9115";
+	reg = <0xf4000000 0x2000000>;
+	phy-mode = "mii";
+	interrupt-parent = <&gpio1>;
+	interrupts = <31>;
+	reg-io-width = <4>;
+	smsc,irq-push-pull;
+};