summaryrefslogtreecommitdiff
path: root/drivers/net/ethernet/intel/e1000e/defines.h
AgeCommit message (Collapse)AuthorFilesLines
2014-07-25e1000e: Fix CRC errors with jumbo trafficDavid Ertman1-0/+1
Modifying the jumbo frame workaround for 82579, i217 and i218 client parts to increase the gap between the read and write pointers in the Tx FIFO. Signed-off-by: Dave Ertman <david.m.ertman@intel.com> Tested-by: Aaron Brown <aaron.f.brown@intel.com> Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
2014-03-07e1000e: Feature Enable PHY Ultra Low Power Mode (ULP)David Ertman1-3/+5
ULP is a power saving feature that reduces the power consumption of the PHY when a cable is not connected. ULP is gated on the following conditions: 1) The hardware must support ULP. Currently this is only I218 devices from Intel 2) ULP is initiated by the driver, so, no driver results in no ULP. 3) ULP's implementation utilizes Runtime Power Management to toggle its execution. ULP is enabled/disabled based on the state of Runtime PM. 4) ULP is not active when wake-on-unicast, multicast or broadcast is active as these features are mutually-exclusive. Since the PHY is in an unavailable state while ULP is active, any access of the PHY registers will fail. This is resolved by utilizing kernel calls that cause the device to exit Runtime PM (e.g. pm_runtime_get_sync) and then, after PHY access is complete, allow the device to resume Runtime PM (e.g. pm_runtime_put_sync). Under certain conditions, toggling the LANPHYPC is necessary to disable ULP mode. Break out existing code to toggle LANPHYPC to a new function to avoid code duplication. Signed-off-by: Dave Ertman <davidx.m.ertman@intel.com> Cc: Bruce Allan <bruce.w.allan@intel.com> Tested-by: Jeff Pieper <jeffrey.e.pieper@intel.com> Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
2014-03-07e1000e: Cleanup - Update GPL header and CopyrightDavid Ertman1-27/+20
This patch is to update the GPL header by removing the portion that refers to the Free Software Foundation address. Change the copyright date for 2014. Reformat the header comments to conform to kernel networking coding norms Signed-off-by: Dave Ertman <davidx.m.ertman@intel.com> Tested-by: Jeff Pieper <jeffrey.e.pieper@intel.com> Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
2013-03-27e1000e: slow performance between two 82579 connected via 10Mbit hubBruce Allan1-0/+1
Two 82579 LOMs connected via a 10Mb hub experience extraordinarily low performance. This is because 82579 is excessively aggressive on transmit at 10Mb half-duplex and will not provide sufficient time for the link partner to transmit. When the link partner is also 82579, the result is a lot of collisions (and corresponding re-transmits) that cause the poor performance. To work-around this issue, significantly increase the IPG in the MAC to allow enough gap for the link partner to transmit and reduce the Rx latency in the analog PHY to 0 to reduce the number of collisions. Signed-off-by: Bruce Allan <bruce.w.allan@intel.com> Tested-by: Jeff Pieper <jeffrey.e.pieper@intel.com> Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
2013-03-27e1000e: additional error handling on PHY register accessesBruce Allan1-0/+1
PHY reads/writes via the MDIC register could potentially return results from a previous PHY register access. If that happens, the offset in the returned results will be that of the previous access and if that is different from the expected offset, log a debug message and error out. Signed-off-by: Bruce Allan <bruce.w.allan@intel.com> Tested-by: Aaron Brown <aaron.f.brown@intel.com> Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
2013-03-08e1000e: cleanup - move defines to appropriate header fileBruce Allan1-0/+3
Signed-off-by: Bruce Allan <bruce.w.allan@intel.com> Tested-by: Aaron Brown <aaron.f.brown@intel.com> Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
2013-03-08e1000e: cleanup (add/remove) blank lines where appropriateBruce Allan1-1/+0
Signed-off-by: Bruce Allan <bruce.w.allan@intel.com> Tested-by: Aaron Brown <aaron.f.brown@intel.com> Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
2013-03-08e1000e: cleanup LONG_LINE checkpatch warningsBruce Allan1-10/+11
WARNING:LONG_LINE: line over 80 characters Signed-off-by: Bruce Allan <bruce.w.allan@intel.com> Tested-by: Aaron Brown <aaron.f.brown@intel.com> Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
2013-02-04e1000e: cosmetic move of #defines and prototypes to the new ich8lan.hBruce Allan1-36/+0
Move #defines and function prototypes specific to the ICH/PCH family of devices (ICH8/82562, ICH8/82566, ICH8/82567, ICH9/82562, ICH9/82566, ICH9/82567, ICH10/82567, 82577, 82578, 82579, I217, I218) to the new ich8lan.h header file (the convention for Intel wired ethernet drivers is to use the name of the first device in the family for related file and function names). These defines and function prototypes can be used by other files in the driver and moving them to the ICH/PCH-family-specific file makes it clearer to which devices they are applicable. Signed-off-by: Bruce Allan <bruce.w.allan@intel.com> Tested-by: Aaron Brown <aaron.f.brown@intel.com> Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
2013-02-04e1000e: cosmetic move of #defines and prototypes to the new 82571.hBruce Allan1-2/+0
Move #defines and function prototypes specific to the 8257x family of devices (82571, 82572, 82573, 82574, 82583) to the new 82571.h header file (the convention for Intel wired ethernet drivers is to use the name of the first device in the family for related file and function names). These defines and function prototypes can be used by other files in the driver and moving them to the 8257x-family-specific file makes it clearer to which devices they are applicable. Signed-off-by: Bruce Allan <bruce.w.allan@intel.com> Tested-by: Aaron Brown <aaron.f.brown@intel.com> Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
2013-01-31e1000e: use generic IEEE MII definitionsBruce Allan1-60/+0
For standard IEEE MII-compatible transceivers, the kernel has generic register and bit definitions. Use those instead of redundant local defines. Do not replace references of MII_CR_SPEED_10 with BMCR_SPEED10 (0x0000) when it is not necessary (i.e. when it is bitwise OR'ed with another value). Some whitespace issues in the surrounding context of the above changes are also cleaned up. Signed-off-by: Bruce Allan <bruce.w.allan@intel.com> Tested-by: Aaron Brown <aaron.f.brown@intel.com> Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
2013-01-31e1000e: cleanup some whitespace and indentation issuesBruce Allan1-23/+24
Signed-off-by: Bruce Allan <bruce.w.allan@intel.com> Tested-by: Aaron Brown <aaron.f.brown@intel.com> Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
2013-01-31e1000e: cleanup defines.hBruce Allan1-21/+0
Remove redundant defines which are defined elsewhere. Signed-off-by: Bruce Allan <bruce.w.allan@intel.com> Tested-by: Aaron Brown <aaron.f.brown@intel.com> Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
2013-01-28e1000e: cleanup: remove comments which are no longer applicableBruce Allan1-7/+0
Code was removed but the applicable comments were not. Signed-off-by: Bruce Allan <bruce.w.allan@intel.com> Tested-by: Aaron Brown <aaron.f.brown@intel.com> Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
2013-01-27e1000e: adjust PM QoS requestBruce Allan1-0/+2
It has been found that devices other than 82579 (a.k.a. e1000_pch2lan) suffer from dropped transactions on platforms with deep C-states when jumbo frames are enabled. For example, LOMs on ICH9- and ICH10-based platforms which recently had early-receive de-featured (for stability reasons) suffer from this. To resolve this for all devices, when jumbo frames are enabled set the PM QoS DMA latency request based on the size of the receive packet buffer less one full frame. Signed-off-by: Bruce Allan <bruce.w.allan@intel.com> Tested-by: Aaron Brown <aaron.f.brown@intel.com> Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
2013-01-27e1000e: update copyright dateBruce Allan1-1/+1
Signed-off-by: Bruce Allan <bruce.w.allan@intel.com> Tested-by: Aaron Brown <aaron.f.brown@intel.com> Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
2013-01-27e1000e: enable ECC on I217/I218 to catch packet buffer memory errorsBruce Allan1-0/+9
In rare instances, memory errors have been detected in the internal packet buffer memory on I217/I218 when stressed under certain environmental conditions. Enable Error Correcting Code (ECC) in hardware to catch both correctable and uncorrectable errors. Correctable errors will be handled by the hardware. Uncorrectable errors in the packet buffer will cause the packet to be received with an error indication in the buffer descriptor causing the packet to be discarded. If the uncorrectable error is in the descriptor itself, the hardware will stop and interrupt the driver indicating the error. The driver will then reset the hardware in order to clear the error and restart. Both types of errors will be accounted for in statistics counters. Signed-off-by: Bruce Allan <bruce.w.allan@intel.com> Tested-by: Jeff Pieper <jeffrey.e.pieper@intel.com> Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
2013-01-27e1000e: add support for IEEE-1588 PTPBruce Allan1-0/+11
Add PTP IEEE-1588 support and make accesible via the PHC subsystem. v2: make e1000e_ptp_clock_info a static const struct per Stephen Hemminger Cc: Stephen Hemminger <stephen@networkplumber.org> Cc: Richard Cochran <richardcochran@gmail.com> Signed-off-by: Bruce Allan <bruce.w.allan@intel.com> Reviewed-by: Jacob Keller <Jacob.e.keller@intel.com> Acked-by: Richard Cochran <richardcochran@gmail.com> Tested-by: Jeff Pieper <jeffrey.e.pieper@intel.com> Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
2013-01-18e1000e: add support for hardware timestamping on some devicesBruce Allan1-0/+14
On 82574, 82583, 82579, I217 and I218 add support for hardware time stamping of all or no Rx packets and Tx packets which have the SKBTX_HW_TSTAMP flag set. Update the .get_ts_info ethtool operation to report the supported time stamping modes, and enable and disable hardware time stamping with the SIOCSHWTSTAMP ioctl. Signed-off-by: Bruce Allan <bruce.w.allan@intel.com> Tested-by: Jeff Pieper <jeffrey.e.pieper@intel.com> Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
2013-01-18e1000e: add ethtool .get_eee/.set_eeeBruce Allan1-0/+30
Add the ability to query and set Energy Efficient Ethernet parameters via ethtool for applicable devices. Signed-off-by: Bruce Allan <bruce.w.allan@intel.com> Tested-by: Jeff Pieper <jeffrey.e.pieper@intel.com> Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
2013-01-15e1000e: Invalid Image CSUM bit changed for I217Bruce Allan1-0/+4
On I217, the bit that indicates an invalid EEPROM (NVM) image checksum has changed from previous ICH/PCH LOMs. When validating the EEPROM checksum, check the appropriate bit on different devices. Signed-off-by: Bruce Allan <bruce.w.allan@intel.com> Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
2013-01-15e1000e: SerDes autoneg flow controlBruce Allan1-3/+3
Enables flow control to be set in SerDes autoneg mode. This is what is done for copper, but relies on a different set of register/bit checks since this is all done within the Mac registers. Remove inapplicable comment in defines.h Signed-off-by: Bruce Allan <bruce.w.allan@intel.com> Tested-by: Aaron Brown <aaron.f.brown@intel.com> Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
2012-12-01e1000e: cosmetic cleanup of commentsBruce Allan1-18/+9
Update comments to conform to the preferred style for networking code as described in ./Documentation/CodingStyle and checked for in the recently added checkpatch NETWORKING_BLOCK_COMMENT_STYLE test. Signed-off-by: Bruce Allan <bruce.w.allan@intel.com> Tested-by: Aaron Brown <aaron.f.brown@intel.com> Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
2012-07-01e1000e: remove use of IP payload checksumBruce Allan1-0/+1
Currently only used when packet split mode is enabled with jumbo frames, IP payload checksum (for fragmented UDP packets) is mutually exclusive with receive hashing offload since the hardware uses the same space in the receive descriptor for the hardware-provided packet checksum and the RSS hash, respectively. Users currently must disable jumbos when receive hashing offload is enabled, or vice versa, because of this incompatibility. Since testing has shown that IP payload checksum does not provide any real benefit, just remove it so that there is no longer a choice between jumbos or receive hashing offload but not both as done in other Intel GbE drivers (e.g. e1000, igb). Also, add a missing check for IP checksum error reported by the hardware; let the stack verify the checksum when this happens. CC: stable <stable@vger.kernel.org> [3.4] Signed-off-by: Bruce Allan <bruce.w.allan@intel.com> Tested-by: Aaron Brown <aaron.f.brown@intel.com> Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com> Signed-off-by: David S. Miller <davem@davemloft.net>
2012-05-17e1000e: fix typo in definition of E1000_CTRL_EXT_FORCE_SMBUSBruce Allan1-1/+1
This define is needed by i217. Reported-by: Bjorn Mork <bjorn@mork.no> Signed-off-by: Bruce Allan <bruce.w.allan@intel.com> Tested-by: Aaron Brown <aaron.f.brown@intel.com> Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
2012-05-04e1000e: initial support for i217Bruce Allan1-0/+8
i217 is the next-generation LOM that will be available on systems with the Lynx Point Platform Controller Hub (PCH) chipset from Intel. This patch provides the initial support for the device. Signed-off-by: Bruce Allan <bruce.w.allan@intel.com> Tested-by: Jeff Pieper <jeffrey.e.pieper@intel.com> Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
2012-02-24e1000e: Support RXALL feature flag.Ben Greear1-0/+1
This allows the NIC to receive all frames available, including those with bad FCS, un-matched vlans, ethernet control frames, and more. Tested by sending frames with bad FCS. Signed-off-by: Ben Greear <greearb@candelatech.com> Tested-by: Aaron Brown <aaron.f.brown@intel.com> Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
2012-01-26e1000e: update copyright yearBruce Allan1-1/+1
Signed-off-by: Bruce Allan <bruce.w.allan@intel.com> Tested-by: Aaron Brown <aaron.f.brown@intel.com> Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
2012-01-25e1000e: add Receive Packet Steering (RPS) supportBruce Allan1-0/+8
Enable RPS by default. Disallow jumbo frames when both receive checksum and receive hashing are enabled because the hardware cannot do both IP payload checksum (enabled when receive checksum is enabled when using packet split which is used for jumbo frames) and provide RSS hash at the same time. v2: added ethtool command to query flow hashing behavior per Ben Hutchings and changed the type of rsskey to cleanup the setting of the register array and avoid unnecessary casts (as pointed out by Joe Perches). The long error messages are not changed since there is nothing in the kernel ./Documentation that suggests the preferred method for dealing with long messages other than to never break strings; leaving them as-is for now. Signed-off-by: Bruce Allan <bruce.w.allan@intel.com> Tested-by: Jeff Pieper <jeffrey.e.pieper@intel.com> Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
2011-08-10intel: Move the Intel wired LAN driversJeff Kirsher1-0/+844
Moves the Intel wired LAN drivers into drivers/net/ethernet/intel/ and the necessary Kconfig and Makefile changes. Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
generated by cgit v1.2.3 (git 2.39.1) at 2024-12-13 16:36:35 +0000