1
2
3
4
5
6
7
8
9
10
11
12
13
14
15
16
17
18
19
20
21
22
23
24
25
26
27
28
29
30
31
32
33
34
35
36
37
38
39
40
41
42
43
44
45
46
47
48
49
50
51
52
53
54
55
56
57
58
59
60
61
62
63
64
65
66
67
68
69
70
71
72
73
74
75
76
77
78
79
80
81
82
83
84
85
86
87
88
89
90
91
92
93
94
95
96
97
98
99
100
101
102
103
104
105
106
107
108
109
110
111
112
113
114
115
116
117
118
119
120
121
122
123
124
125
126
127
128
129
130
131
132
133
134
135
136
137
138
139
140
141
142
143
144
145
146
147
148
149
150
151
152
153
154
155
156
157
158
159
160
161
162
163
164
165
166
167
168
169
170
171
172
173
174
175
176
177
178
179
180
181
182
183
184
185
186
187
188
189
190
191
192
193
194
195
196
197
198
199
200
201
202
203
204
205
206
207
208
209
210
|
# SPDX-License-Identifier: (GPL-2.0+ OR BSD-2-Clause)
# Copyright (C) 2019 Texas Instruments Incorporated
%YAML 1.2
---
$id: http://devicetree.org/schemas/sound/tlv320adcx140.yaml#
$schema: http://devicetree.org/meta-schemas/core.yaml#
title: Texas Instruments TLV320ADCX140 Quad Channel Analog-to-Digital Converter
maintainers:
- Dan Murphy <dmurphy@ti.com>
description: |
The TLV320ADCX140 are multichannel (4-ch analog recording or 8-ch digital
PDM microphones recording), high-performance audio, analog-to-digital
converter (ADC) with analog inputs supporting up to 2V RMS. The TLV320ADCX140
family supports line and microphone Inputs, and offers a programmable
microphone bias or supply voltage generation.
Specifications can be found at:
https://www.ti.com/lit/ds/symlink/tlv320adc3140.pdf
https://www.ti.com/lit/ds/symlink/tlv320adc5140.pdf
https://www.ti.com/lit/ds/symlink/tlv320adc6140.pdf
properties:
compatible:
enum:
- ti,tlv320adc3140
- ti,tlv320adc5140
- ti,tlv320adc6140
reg:
maxItems: 1
description: |
I2C addresss of the device can be one of these 0x4c, 0x4d, 0x4e or 0x4f
reset-gpios:
maxItems: 1
description: |
GPIO used for hardware reset.
areg-supply:
description: |
Regulator with AVDD at 3.3V. If not defined then the internal regulator
is enabled.
ti,mic-bias-source:
description: |
Indicates the source for MIC Bias.
0 - Mic bias is set to VREF
1 - Mic bias is set to VREF × 1.096
6 - Mic bias is set to AVDD
$ref: /schemas/types.yaml#/definitions/uint32
enum: [0, 1, 6]
ti,vref-source:
description: |
Indicates the source for MIC Bias.
0 - Set VREF to 2.75V
1 - Set VREF to 2.5V
2 - Set VREF to 1.375V
$ref: /schemas/types.yaml#/definitions/uint32
enum: [0, 1, 2]
ti,pdm-edge-select:
description: |
Defines the PDMCLK sampling edge configuration for the PDM inputs. This
array is defined as <PDMIN1 PDMIN2 PDMIN3 PDMIN4>.
0 - (default) Odd channel is latched on the negative edge and even
channel is latched on the the positive edge.
1 - Odd channel is latched on the positive edge and even channel is
latched on the the negative edge.
PDMIN1 - PDMCLK latching edge used for channel 1 and 2 data
PDMIN2 - PDMCLK latching edge used for channel 3 and 4 data
PDMIN3 - PDMCLK latching edge used for channel 5 and 6 data
PDMIN4 - PDMCLK latching edge used for channel 7 and 8 data
$ref: /schemas/types.yaml#/definitions/uint32-array
minItems: 1
maxItems: 4
items:
maximum: 1
default: [0, 0, 0, 0]
ti,gpi-config:
description: |
Defines the configuration for the general purpose input pins (GPI).
The array is defined as <GPI1 GPI2 GPI3 GPI4>.
0 - (default) disabled
1 - GPIX is configured as a general-purpose input (GPI)
2 - GPIX is configured as a master clock input (MCLK)
3 - GPIX is configured as an ASI input for daisy-chain (SDIN)
4 - GPIX is configured as a PDM data input for channel 1 and channel
(PDMDIN1)
5 - GPIX is configured as a PDM data input for channel 3 and channel
(PDMDIN2)
6 - GPIX is configured as a PDM data input for channel 5 and channel
(PDMDIN3)
7 - GPIX is configured as a PDM data input for channel 7 and channel
(PDMDIN4)
$ref: /schemas/types.yaml#/definitions/uint32-array
minItems: 1
maxItems: 4
items:
maximum: 7
default: [0, 0, 0, 0]
ti,asi-tx-drive:
type: boolean
description: |
When set the device will set the Tx ASI output to a Hi-Z state for unused
data cycles. Default is to drive the output low on unused ASI cycles.
patternProperties:
'^ti,gpo-config-[1-4]$':
$ref: /schemas/types.yaml#/definitions/uint32-array
description: |
Defines the configuration and output driver for the general purpose
output pins (GPO). These values are pairs, the first value is for the
configuration type and the second value is for the output drive type.
The array is defined as <GPO_CFG GPO_DRV>
GPO output configuration can be one of the following:
0 - (default) disabled
1 - GPOX is configured as a general-purpose output (GPO)
2 - GPOX is configured as a device interrupt output (IRQ)
3 - GPOX is configured as a secondary ASI output (SDOUT2)
4 - GPOX is configured as a PDM clock output (PDMCLK)
GPO output drive configuration for the GPO pins can be one of the following:
0d - (default) Hi-Z output
1d - Drive active low and active high
2d - Drive active low and weak high
3d - Drive active low and Hi-Z
4d - Drive weak low and active high
5d - Drive Hi-Z and active high
ti,gpio-config:
description: |
Defines the configuration and output drive for the General Purpose
Input and Output pin (GPIO1). Its value is a pair, the first value is for
the configuration type and the second value is for the output drive
type. The array is defined as <GPIO1_CFG GPIO1_DRV>
configuration for the GPIO pin can be one of the following:
0 - disabled
1 - GPIO1 is configured as a general-purpose output (GPO)
2 - (default) GPIO1 is configured as a device interrupt output (IRQ)
3 - GPIO1 is configured as a secondary ASI output (SDOUT2)
4 - GPIO1 is configured as a PDM clock output (PDMCLK)
8 - GPIO1 is configured as an input to control when MICBIAS turns on or
off (MICBIAS_EN)
9 - GPIO1 is configured as a general-purpose input (GPI)
10 - GPIO1 is configured as a master clock input (MCLK)
11 - GPIO1 is configured as an ASI input for daisy-chain (SDIN)
12 - GPIO1 is configured as a PDM data input for channel 1 and channel 2
(PDMDIN1)
13 - GPIO1 is configured as a PDM data input for channel 3 and channel 4
(PDMDIN2)
14 - GPIO1 is configured as a PDM data input for channel 5 and channel 6
(PDMDIN3)
15 - GPIO1 is configured as a PDM data input for channel 7 and channel 8
(PDMDIN4)
output drive type for the GPIO pin can be one of the following:
0 - Hi-Z output
1 - Drive active low and active high
2 - (default) Drive active low and weak high
3 - Drive active low and Hi-Z
4 - Drive weak low and active high
5 - Drive Hi-Z and active high
allOf:
- $ref: /schemas/types.yaml#/definitions/uint32-array
- minItems: 2
maxItems: 2
items:
maximum: 15
default: [2, 2]
required:
- compatible
- reg
additionalProperties: false
examples:
- |
#include <dt-bindings/gpio/gpio.h>
i2c0 {
#address-cells = <1>;
#size-cells = <0>;
codec: codec@4c {
compatible = "ti,tlv320adc5140";
reg = <0x4c>;
ti,mic-bias-source = <6>;
ti,pdm-edge-select = <0 1 0 1>;
ti,gpi-config = <4 5 6 7>;
ti,gpio-config = <10 2>;
ti,gpo-config-1 = <0 0>;
ti,gpo-config-2 = <0 0>;
reset-gpios = <&gpio0 14 GPIO_ACTIVE_HIGH>;
};
};
|
