1
2
3
4
5
6
7
8
9
10
11
12
13
14
15
16
17
18
19
20
21
22
23
24
25
26
27
28
29
30
31
32
33
34
35
36
37
38
39
40
41
42
43
44
45
46
47
48
49
50
51
52
53
54
55
56
57
58
59
60
61
62
63
64
65
66
67
68
69
70
71
72
73
74
75
76
77
78
79
80
81
82
83
84
85
86
87
88
89
90
91
92
93
94
95
96
97
98
99
100
101
102
103
104
105
106
107
108
109
110
111
112
113
114
115
116
117
118
|
* Freescale Smart Direct Memory Access (SDMA) Controller for i.MX
Required properties:
- compatible : Should be one of
"fsl,imx25-sdma"
"fsl,imx31-sdma", "fsl,imx31-to1-sdma", "fsl,imx31-to2-sdma"
"fsl,imx35-sdma", "fsl,imx35-to1-sdma", "fsl,imx35-to2-sdma"
"fsl,imx51-sdma"
"fsl,imx53-sdma"
"fsl,imx6q-sdma"
"fsl,imx7d-sdma"
"fsl,imx6ul-sdma"
"fsl,imx8mq-sdma"
"fsl,imx8mm-sdma"
"fsl,imx8mn-sdma"
"fsl,imx8mp-sdma"
The -to variants should be preferred since they allow to determine the
correct ROM script addresses needed for the driver to work without additional
firmware.
- reg : Should contain SDMA registers location and length
- interrupts : Should contain SDMA interrupt
- #dma-cells : Must be <3>.
The first cell specifies the DMA request/event ID. See details below
about the second and third cell.
- fsl,sdma-ram-script-name : Should contain the full path of SDMA RAM
scripts firmware
The second cell of dma phandle specifies the peripheral type of DMA transfer.
The full ID of peripheral types can be found below.
ID transfer type
---------------------
0 MCU domain SSI
1 Shared SSI
2 MMC
3 SDHC
4 MCU domain UART
5 Shared UART
6 FIRI
7 MCU domain CSPI
8 Shared CSPI
9 SIM
10 ATA
11 CCM
12 External peripheral
13 Memory Stick Host Controller
14 Shared Memory Stick Host Controller
15 DSP
16 Memory
17 FIFO type Memory
18 SPDIF
19 IPU Memory
20 ASRC
21 ESAI
22 SSI Dual FIFO (needs firmware ver >= 2)
23 Shared ASRC
24 SAI
The third cell specifies the transfer priority as below.
ID transfer priority
-------------------------
0 High
1 Medium
2 Low
Optional properties:
- gpr : The phandle to the General Purpose Register (GPR) node.
- fsl,sdma-event-remap : Register bits of sdma event remap, the format is
<reg shift val>.
reg is the GPR register offset.
shift is the bit position inside the GPR register.
val is the value of the bit (0 or 1).
Examples:
sdma@83fb0000 {
compatible = "fsl,imx51-sdma", "fsl,imx35-sdma";
reg = <0x83fb0000 0x4000>;
interrupts = <6>;
#dma-cells = <3>;
fsl,sdma-ram-script-name = "sdma-imx51.bin";
};
DMA clients connected to the i.MX SDMA controller must use the format
described in the dma.txt file.
Examples:
ssi2: ssi@70014000 {
compatible = "fsl,imx51-ssi", "fsl,imx21-ssi";
reg = <0x70014000 0x4000>;
interrupts = <30>;
clocks = <&clks 49>;
dmas = <&sdma 24 1 0>,
<&sdma 25 1 0>;
dma-names = "rx", "tx";
fsl,fifo-depth = <15>;
};
Using the fsl,sdma-event-remap property:
If we want to use SDMA on the SAI1 port on a MX6SX:
&sdma {
gpr = <&gpr>;
/* SDMA events remap for SAI1_RX and SAI1_TX */
fsl,sdma-event-remap = <0 15 1>, <0 16 1>;
};
The fsl,sdma-event-remap property in this case has two values:
- <0 15 1> means that the offset is 0, so GPR0 is the register of the
SDMA remap. Bit 15 of GPR0 selects between UART4_RX and SAI1_RX.
Setting bit 15 to 1 selects SAI1_RX.
- <0 16 1> means that the offset is 0, so GPR0 is the register of the
SDMA remap. Bit 16 of GPR0 selects between UART4_TX and SAI1_TX.
Setting bit 16 to 1 selects SAI1_TX.
|
