summaryrefslogtreecommitdiff
path: root/drivers/net
diff options
context:
space:
mode:
Diffstat (limited to 'drivers/net')
-rw-r--r--drivers/net/igb/e1000_hw.h6
-rw-r--r--drivers/net/igb/e1000_mac.c50
-rw-r--r--drivers/net/igb/e1000_phy.c4
-rw-r--r--drivers/net/igb/igb_ethtool.c34
-rw-r--r--drivers/net/igb/igb_main.c6
5 files changed, 55 insertions, 45 deletions
diff --git a/drivers/net/igb/e1000_hw.h b/drivers/net/igb/e1000_hw.h
index 0469e2e7e63c..119869b1124d 100644
--- a/drivers/net/igb/e1000_hw.h
+++ b/drivers/net/igb/e1000_hw.h
@@ -137,7 +137,7 @@ enum e1000_rev_polarity {
e1000_rev_polarity_undefined = 0xFF
};
-enum e1000_fc_type {
+enum e1000_fc_mode {
e1000_fc_none = 0,
e1000_fc_rx_pause,
e1000_fc_tx_pause,
@@ -429,8 +429,8 @@ struct e1000_fc_info {
u16 pause_time; /* Flow control pause timer */
bool send_xon; /* Flow control send XON */
bool strict_ieee; /* Strict IEEE mode */
- enum e1000_fc_type type; /* Type of flow control */
- enum e1000_fc_type original_type;
+ enum e1000_fc_mode current_mode; /* Type of flow control */
+ enum e1000_fc_mode requested_mode;
};
struct e1000_mbx_operations {
diff --git a/drivers/net/igb/e1000_mac.c b/drivers/net/igb/e1000_mac.c
index a1e3da78dbb1..a0231cd079f1 100644
--- a/drivers/net/igb/e1000_mac.c
+++ b/drivers/net/igb/e1000_mac.c
@@ -536,18 +536,24 @@ s32 igb_setup_link(struct e1000_hw *hw)
if (igb_check_reset_block(hw))
goto out;
- ret_val = igb_set_default_fc(hw);
- if (ret_val)
- goto out;
+ /*
+ * If requested flow control is set to default, set flow control
+ * based on the EEPROM flow control settings.
+ */
+ if (hw->fc.requested_mode == e1000_fc_default) {
+ ret_val = igb_set_default_fc(hw);
+ if (ret_val)
+ goto out;
+ }
/*
* We want to save off the original Flow Control configuration just
* in case we get disconnected and then reconnected into a different
* hub or switch with different Flow Control capabilities.
*/
- hw->fc.original_type = hw->fc.type;
+ hw->fc.current_mode = hw->fc.requested_mode;
- hw_dbg("After fix-ups FlowControl is now = %x\n", hw->fc.type);
+ hw_dbg("After fix-ups FlowControl is now = %x\n", hw->fc.current_mode);
/* Call the necessary media_type subroutine to configure the link. */
ret_val = hw->mac.ops.setup_physical_interface(hw);
@@ -614,7 +620,7 @@ static s32 igb_set_fc_watermarks(struct e1000_hw *hw)
* ability to transmit pause frames is not enabled, then these
* registers will be set to 0.
*/
- if (hw->fc.type & e1000_fc_tx_pause) {
+ if (hw->fc.current_mode & e1000_fc_tx_pause) {
/*
* We need to set up the Receive Threshold high and low water
* marks as well as (optionally) enabling the transmission of
@@ -661,12 +667,12 @@ static s32 igb_set_default_fc(struct e1000_hw *hw)
}
if ((nvm_data & NVM_WORD0F_PAUSE_MASK) == 0)
- hw->fc.type = e1000_fc_none;
+ hw->fc.requested_mode = e1000_fc_none;
else if ((nvm_data & NVM_WORD0F_PAUSE_MASK) ==
NVM_WORD0F_ASM_DIR)
- hw->fc.type = e1000_fc_tx_pause;
+ hw->fc.requested_mode = e1000_fc_tx_pause;
else
- hw->fc.type = e1000_fc_full;
+ hw->fc.requested_mode = e1000_fc_full;
out:
return ret_val;
@@ -696,7 +702,7 @@ s32 igb_force_mac_fc(struct e1000_hw *hw)
* receive flow control.
*
* The "Case" statement below enables/disable flow control
- * according to the "hw->fc.type" parameter.
+ * according to the "hw->fc.current_mode" parameter.
*
* The possible values of the "fc" parameter are:
* 0: Flow control is completely disabled
@@ -707,9 +713,9 @@ s32 igb_force_mac_fc(struct e1000_hw *hw)
* 3: Both Rx and TX flow control (symmetric) is enabled.
* other: No other values should be possible at this point.
*/
- hw_dbg("hw->fc.type = %u\n", hw->fc.type);
+ hw_dbg("hw->fc.current_mode = %u\n", hw->fc.current_mode);
- switch (hw->fc.type) {
+ switch (hw->fc.current_mode) {
case e1000_fc_none:
ctrl &= (~(E1000_CTRL_TFCE | E1000_CTRL_RFCE));
break;
@@ -857,11 +863,11 @@ s32 igb_config_fc_after_link_up(struct e1000_hw *hw)
* ONLY. Hence, we must now check to see if we need to
* turn OFF the TRANSMISSION of PAUSE frames.
*/
- if (hw->fc.original_type == e1000_fc_full) {
- hw->fc.type = e1000_fc_full;
+ if (hw->fc.requested_mode == e1000_fc_full) {
+ hw->fc.current_mode = e1000_fc_full;
hw_dbg("Flow Control = FULL.\r\n");
} else {
- hw->fc.type = e1000_fc_rx_pause;
+ hw->fc.current_mode = e1000_fc_rx_pause;
hw_dbg("Flow Control = "
"RX PAUSE frames only.\r\n");
}
@@ -878,7 +884,7 @@ s32 igb_config_fc_after_link_up(struct e1000_hw *hw)
(mii_nway_adv_reg & NWAY_AR_ASM_DIR) &&
(mii_nway_lp_ability_reg & NWAY_LPAR_PAUSE) &&
(mii_nway_lp_ability_reg & NWAY_LPAR_ASM_DIR)) {
- hw->fc.type = e1000_fc_tx_pause;
+ hw->fc.current_mode = e1000_fc_tx_pause;
hw_dbg("Flow Control = TX PAUSE frames only.\r\n");
}
/*
@@ -893,7 +899,7 @@ s32 igb_config_fc_after_link_up(struct e1000_hw *hw)
(mii_nway_adv_reg & NWAY_AR_ASM_DIR) &&
!(mii_nway_lp_ability_reg & NWAY_LPAR_PAUSE) &&
(mii_nway_lp_ability_reg & NWAY_LPAR_ASM_DIR)) {
- hw->fc.type = e1000_fc_rx_pause;
+ hw->fc.current_mode = e1000_fc_rx_pause;
hw_dbg("Flow Control = RX PAUSE frames only.\r\n");
}
/*
@@ -917,13 +923,13 @@ s32 igb_config_fc_after_link_up(struct e1000_hw *hw)
* be asked to delay transmission of packets than asking
* our link partner to pause transmission of frames.
*/
- else if ((hw->fc.original_type == e1000_fc_none ||
- hw->fc.original_type == e1000_fc_tx_pause) ||
+ else if ((hw->fc.requested_mode == e1000_fc_none ||
+ hw->fc.requested_mode == e1000_fc_tx_pause) ||
hw->fc.strict_ieee) {
- hw->fc.type = e1000_fc_none;
+ hw->fc.current_mode = e1000_fc_none;
hw_dbg("Flow Control = NONE.\r\n");
} else {
- hw->fc.type = e1000_fc_rx_pause;
+ hw->fc.current_mode = e1000_fc_rx_pause;
hw_dbg("Flow Control = RX PAUSE frames only.\r\n");
}
@@ -939,7 +945,7 @@ s32 igb_config_fc_after_link_up(struct e1000_hw *hw)
}
if (duplex == HALF_DUPLEX)
- hw->fc.type = e1000_fc_none;
+ hw->fc.current_mode = e1000_fc_none;
/*
* Now we call a subroutine to actually force the MAC
diff --git a/drivers/net/igb/e1000_phy.c b/drivers/net/igb/e1000_phy.c
index f50fac25be40..c1f4da630420 100644
--- a/drivers/net/igb/e1000_phy.c
+++ b/drivers/net/igb/e1000_phy.c
@@ -735,7 +735,7 @@ static s32 igb_phy_setup_autoneg(struct e1000_hw *hw)
* other: No software override. The flow control configuration
* in the EEPROM is used.
*/
- switch (hw->fc.type) {
+ switch (hw->fc.current_mode) {
case e1000_fc_none:
/*
* Flow control (RX & TX) is completely disabled by a
@@ -992,7 +992,7 @@ static void igb_phy_force_speed_duplex_setup(struct e1000_hw *hw,
u32 ctrl;
/* Turn off flow control when forcing speed/duplex */
- hw->fc.type = e1000_fc_none;
+ hw->fc.current_mode = e1000_fc_none;
/* Force speed/duplex on the mac */
ctrl = rd32(E1000_CTRL);
diff --git a/drivers/net/igb/igb_ethtool.c b/drivers/net/igb/igb_ethtool.c
index df2d234be229..114ccab1f2be 100644
--- a/drivers/net/igb/igb_ethtool.c
+++ b/drivers/net/igb/igb_ethtool.c
@@ -194,6 +194,8 @@ static int igb_set_settings(struct net_device *netdev, struct ethtool_cmd *ecmd)
ADVERTISED_TP |
ADVERTISED_Autoneg;
ecmd->advertising = hw->phy.autoneg_advertised;
+ if (adapter->fc_autoneg)
+ hw->fc.requested_mode = e1000_fc_default;
} else {
if (igb_set_spd_dplx(adapter, ecmd->speed + ecmd->duplex)) {
clear_bit(__IGB_RESETTING, &adapter->state);
@@ -221,11 +223,11 @@ static void igb_get_pauseparam(struct net_device *netdev,
pause->autoneg =
(adapter->fc_autoneg ? AUTONEG_ENABLE : AUTONEG_DISABLE);
- if (hw->fc.type == e1000_fc_rx_pause)
+ if (hw->fc.current_mode == e1000_fc_rx_pause)
pause->rx_pause = 1;
- else if (hw->fc.type == e1000_fc_tx_pause)
+ else if (hw->fc.current_mode == e1000_fc_tx_pause)
pause->tx_pause = 1;
- else if (hw->fc.type == e1000_fc_full) {
+ else if (hw->fc.current_mode == e1000_fc_full) {
pause->rx_pause = 1;
pause->tx_pause = 1;
}
@@ -243,26 +245,28 @@ static int igb_set_pauseparam(struct net_device *netdev,
while (test_and_set_bit(__IGB_RESETTING, &adapter->state))
msleep(1);
- if (pause->rx_pause && pause->tx_pause)
- hw->fc.type = e1000_fc_full;
- else if (pause->rx_pause && !pause->tx_pause)
- hw->fc.type = e1000_fc_rx_pause;
- else if (!pause->rx_pause && pause->tx_pause)
- hw->fc.type = e1000_fc_tx_pause;
- else if (!pause->rx_pause && !pause->tx_pause)
- hw->fc.type = e1000_fc_none;
-
- hw->fc.original_type = hw->fc.type;
-
if (adapter->fc_autoneg == AUTONEG_ENABLE) {
+ hw->fc.requested_mode = e1000_fc_default;
if (netif_running(adapter->netdev)) {
igb_down(adapter);
igb_up(adapter);
} else
igb_reset(adapter);
- } else
+ } else {
+ if (pause->rx_pause && pause->tx_pause)
+ hw->fc.requested_mode = e1000_fc_full;
+ else if (pause->rx_pause && !pause->tx_pause)
+ hw->fc.requested_mode = e1000_fc_rx_pause;
+ else if (!pause->rx_pause && pause->tx_pause)
+ hw->fc.requested_mode = e1000_fc_tx_pause;
+ else if (!pause->rx_pause && !pause->tx_pause)
+ hw->fc.requested_mode = e1000_fc_none;
+
+ hw->fc.current_mode = hw->fc.requested_mode;
+
retval = ((hw->phy.media_type == e1000_media_type_copper) ?
igb_force_mac_fc(hw) : igb_setup_link(hw));
+ }
clear_bit(__IGB_RESETTING, &adapter->state);
return retval;
diff --git a/drivers/net/igb/igb_main.c b/drivers/net/igb/igb_main.c
index 12d8683c231e..fb3273517587 100644
--- a/drivers/net/igb/igb_main.c
+++ b/drivers/net/igb/igb_main.c
@@ -1130,7 +1130,7 @@ void igb_reset(struct igb_adapter *adapter)
}
fc->pause_time = 0xFFFF;
fc->send_xon = 1;
- fc->type = fc->original_type;
+ fc->current_mode = fc->requested_mode;
/* disable receive for all VFs and wait one second */
if (adapter->vfs_allocated_count) {
@@ -1427,8 +1427,8 @@ static int __devinit igb_probe(struct pci_dev *pdev,
hw->mac.autoneg = true;
hw->phy.autoneg_advertised = 0x2f;
- hw->fc.original_type = e1000_fc_default;
- hw->fc.type = e1000_fc_default;
+ hw->fc.requested_mode = e1000_fc_default;
+ hw->fc.current_mode = e1000_fc_default;
adapter->itr_setting = IGB_DEFAULT_ITR;
adapter->itr = IGB_START_ITR;
generated by cgit v1.2.3 (git 2.39.1) at 2024-12-04 21:47:18 +0000