diff options
Diffstat (limited to 'drivers/ide/jmicron.c')
| -rw-r--r-- | drivers/ide/jmicron.c | 176 |
1 files changed, 0 insertions, 176 deletions
diff --git a/drivers/ide/jmicron.c b/drivers/ide/jmicron.c deleted file mode 100644 index ae6480dcbadf..000000000000 --- a/drivers/ide/jmicron.c +++ /dev/null @@ -1,176 +0,0 @@ - -/* - * Copyright (C) 2006 Red Hat - * - * May be copied or modified under the terms of the GNU General Public License - */ - -#include <linux/types.h> -#include <linux/module.h> -#include <linux/pci.h> -#include <linux/ide.h> -#include <linux/init.h> - -#define DRV_NAME "jmicron" - -typedef enum { - PORT_PATA0 = 0, - PORT_PATA1 = 1, - PORT_SATA = 2, -} port_type; - -/** - * jmicron_cable_detect - cable detection - * @hwif: IDE port - * - * Returns the cable type. - */ - -static u8 jmicron_cable_detect(ide_hwif_t *hwif) -{ - struct pci_dev *pdev = to_pci_dev(hwif->dev); - - u32 control; - u32 control5; - - int port = hwif->channel; - port_type port_map[2]; - - pci_read_config_dword(pdev, 0x40, &control); - - /* There are two basic mappings. One has the two SATA ports merged - as master/slave and the secondary as PATA, the other has only the - SATA port mapped */ - if (control & (1 << 23)) { - port_map[0] = PORT_SATA; - port_map[1] = PORT_PATA0; - } else { - port_map[0] = PORT_SATA; - port_map[1] = PORT_SATA; - } - - /* The 365/366 may have this bit set to map the second PATA port - as the internal primary channel */ - pci_read_config_dword(pdev, 0x80, &control5); - if (control5 & (1<<24)) - port_map[0] = PORT_PATA1; - - /* The two ports may then be logically swapped by the firmware */ - if (control & (1 << 22)) - port = port ^ 1; - - /* - * Now we know which physical port we are talking about we can - * actually do our cable checking etc. Thankfully we don't need - * to do the plumbing for other cases. - */ - switch (port_map[port]) { - case PORT_PATA0: - if (control & (1 << 3)) /* 40/80 pin primary */ - return ATA_CBL_PATA40; - return ATA_CBL_PATA80; - case PORT_PATA1: - if (control5 & (1 << 19)) /* 40/80 pin secondary */ - return ATA_CBL_PATA40; - return ATA_CBL_PATA80; - case PORT_SATA: - break; - } - /* Avoid bogus "control reaches end of non-void function" */ - return ATA_CBL_PATA80; -} - -static void jmicron_set_pio_mode(ide_hwif_t *hwif, ide_drive_t *drive) -{ -} - -/** - * jmicron_set_dma_mode - set host controller for DMA mode - * @hwif: port - * @drive: drive - * - * As the JMicron snoops for timings we don't need to do anything here. - */ - -static void jmicron_set_dma_mode(ide_hwif_t *hwif, ide_drive_t *drive) -{ -} - -static const struct ide_port_ops jmicron_port_ops = { - .set_pio_mode = jmicron_set_pio_mode, - .set_dma_mode = jmicron_set_dma_mode, - .cable_detect = jmicron_cable_detect, -}; - -static const struct ide_port_info jmicron_chipset = { - .name = DRV_NAME, - .enablebits = { { 0x40, 0x01, 0x01 }, { 0x40, 0x10, 0x10 } }, - .port_ops = &jmicron_port_ops, - .pio_mask = ATA_PIO5, - .mwdma_mask = ATA_MWDMA2, - .udma_mask = ATA_UDMA6, -}; - -/** - * jmicron_init_one - pci layer discovery entry - * @dev: PCI device - * @id: ident table entry - * - * Called by the PCI code when it finds a Jmicron controller. - * We then use the IDE PCI generic helper to do most of the work. - */ - -static int jmicron_init_one(struct pci_dev *dev, const struct pci_device_id *id) -{ - return ide_pci_init_one(dev, &jmicron_chipset, NULL); -} - -/* All JMB PATA controllers have and will continue to have the same - * interface. Matching vendor and device class is enough for all - * current and future controllers if the controller is programmed - * properly. - * - * If libata is configured, jmicron PCI quirk programs the controller - * into the correct mode. If libata isn't configured, match known - * device IDs too to maintain backward compatibility. - */ -static struct pci_device_id jmicron_pci_tbl[] = { -#if !defined(CONFIG_ATA) && !defined(CONFIG_ATA_MODULE) - { PCI_VDEVICE(JMICRON, PCI_DEVICE_ID_JMICRON_JMB361) }, - { PCI_VDEVICE(JMICRON, PCI_DEVICE_ID_JMICRON_JMB363) }, - { PCI_VDEVICE(JMICRON, PCI_DEVICE_ID_JMICRON_JMB365) }, - { PCI_VDEVICE(JMICRON, PCI_DEVICE_ID_JMICRON_JMB366) }, - { PCI_VDEVICE(JMICRON, PCI_DEVICE_ID_JMICRON_JMB368) }, -#endif - { PCI_VENDOR_ID_JMICRON, PCI_ANY_ID, PCI_ANY_ID, PCI_ANY_ID, - PCI_CLASS_STORAGE_IDE << 8, 0xffff00, 0 }, - { 0, }, -}; - -MODULE_DEVICE_TABLE(pci, jmicron_pci_tbl); - -static struct pci_driver jmicron_pci_driver = { - .name = "JMicron IDE", - .id_table = jmicron_pci_tbl, - .probe = jmicron_init_one, - .remove = ide_pci_remove, - .suspend = ide_pci_suspend, - .resume = ide_pci_resume, -}; - -static int __init jmicron_ide_init(void) -{ - return ide_pci_register_driver(&jmicron_pci_driver); -} - -static void __exit jmicron_ide_exit(void) -{ - pci_unregister_driver(&jmicron_pci_driver); -} - -module_init(jmicron_ide_init); -module_exit(jmicron_ide_exit); - -MODULE_AUTHOR("Alan Cox"); -MODULE_DESCRIPTION("PCI driver module for the JMicron in legacy modes"); -MODULE_LICENSE("GPL"); |