diff options
Diffstat (limited to 'arch/arm')
| -rw-r--r-- | arch/arm/Kconfig | 39 | ||||
| -rw-r--r-- | arch/arm/common/Kconfig | 3 | ||||
| -rw-r--r-- | arch/arm/common/Makefile | 1 | ||||
| -rw-r--r-- | arch/arm/common/gic.c | 166 | ||||
| -rw-r--r-- | arch/arm/kernel/signal.c | 5 | ||||
| -rw-r--r-- | arch/arm/mach-ixp4xx/coyote-setup.c | 2 | ||||
| -rw-r--r-- | arch/arm/mach-ixp4xx/gtwx5715-setup.c | 2 | ||||
| -rw-r--r-- | arch/arm/mach-ixp4xx/ixdp425-setup.c | 2 | ||||
| -rw-r--r-- | arch/arm/mach-sa1100/assabet.c | 7 | ||||
| -rw-r--r-- | arch/arm/mach-sa1100/cerf.c | 7 | ||||
| -rw-r--r-- | arch/arm/mach-sa1100/generic.c | 5 | ||||
| -rw-r--r-- | arch/arm/mach-sa1100/generic.h | 3 | ||||
| -rw-r--r-- | arch/arm/mach-sa1100/lart.c | 12 | ||||
| -rw-r--r-- | arch/arm/mach-sa1100/shannon.c | 7 | ||||
| -rw-r--r-- | arch/arm/mach-sa1100/simpad.c | 7 |
15 files changed, 226 insertions, 42 deletions
diff --git a/arch/arm/Kconfig b/arch/arm/Kconfig index c65c6eb9810d..4bf0e8737e1f 100644 --- a/arch/arm/Kconfig +++ b/arch/arm/Kconfig @@ -635,10 +635,6 @@ config PM and the Battery Powered Linux mini-HOWTO, available from <http://www.tldp.org/docs.html#howto>. - Note that, even if you say N here, Linux on the x86 architecture - will issue the hlt instruction if nothing is to be done, thereby - sending the processor to sleep and saving power. - config APM tristate "Advanced Power Management Emulation" depends on PM @@ -650,12 +646,6 @@ config APM battery status information, and user-space programs will receive notification of APM "events" (e.g. battery status change). - If you select "Y" here, you can disable actual use of the APM - BIOS by passing the "apm=off" option to the kernel at boot time. - - Note that the APM support is almost completely disabled for - machines with more than one CPU. - In order to use APM, you will need supporting software. For location and more information, read <file:Documentation/pm.txt> and the Battery Powered Linux mini-HOWTO, available from @@ -665,39 +655,12 @@ config APM manpage ("man 8 hdparm") for that), and it doesn't turn off VESA-compliant "green" monitors. - This driver does not support the TI 4000M TravelMate and the ACER - 486/DX4/75 because they don't have compliant BIOSes. Many "green" - desktop machines also don't have compliant BIOSes, and this driver - may cause those machines to panic during the boot phase. - Generally, if you don't have a battery in your machine, there isn't much point in using this driver and you should say N. If you get random kernel OOPSes or reboots that don't seem to be related to anything, try disabling/enabling this option (or disabling/enabling APM in your BIOS). - Some other things you should try when experiencing seemingly random, - "weird" problems: - - 1) make sure that you have enough swap space and that it is - enabled. - 2) pass the "no-hlt" option to the kernel - 3) switch on floating point emulation in the kernel and pass - the "no387" option to the kernel - 4) pass the "floppy=nodma" option to the kernel - 5) pass the "mem=4M" option to the kernel (thereby disabling - all but the first 4 MB of RAM) - 6) make sure that the CPU is not over clocked. - 7) read the sig11 FAQ at <http://www.bitwizard.nl/sig11/> - 8) disable the cache from your BIOS settings - 9) install a fan for the video card or exchange video RAM - 10) install a better fan for the CPU - 11) exchange RAM chips - 12) exchange the motherboard. - - To compile this driver as a module, choose M here: the - module will be called apm. - endmenu source "net/Kconfig" @@ -752,6 +715,8 @@ source "drivers/hwmon/Kconfig" source "drivers/misc/Kconfig" +source "drivers/mfd/Kconfig" + source "drivers/media/Kconfig" source "drivers/video/Kconfig" diff --git a/arch/arm/common/Kconfig b/arch/arm/common/Kconfig index 692af6b5e8ff..666ba393575b 100644 --- a/arch/arm/common/Kconfig +++ b/arch/arm/common/Kconfig @@ -1,6 +1,9 @@ config ICST525 bool +config ARM_GIC + bool + config ICST307 bool diff --git a/arch/arm/common/Makefile b/arch/arm/common/Makefile index 11f20a43ee3a..a87886564b19 100644 --- a/arch/arm/common/Makefile +++ b/arch/arm/common/Makefile @@ -4,6 +4,7 @@ obj-y += rtctime.o obj-$(CONFIG_ARM_AMBA) += amba.o +obj-$(CONFIG_ARM_GIC) += gic.o obj-$(CONFIG_ICST525) += icst525.o obj-$(CONFIG_ICST307) += icst307.o obj-$(CONFIG_SA1111) += sa1111.o diff --git a/arch/arm/common/gic.c b/arch/arm/common/gic.c new file mode 100644 index 000000000000..51dbf5489b6b --- /dev/null +++ b/arch/arm/common/gic.c @@ -0,0 +1,166 @@ +/* + * linux/arch/arm/common/gic.c + * + * Copyright (C) 2002 ARM Limited, All Rights Reserved. + * + * This program is free software; you can redistribute it and/or modify + * it under the terms of the GNU General Public License version 2 as + * published by the Free Software Foundation. + * + * Interrupt architecture for the GIC: + * + * o There is one Interrupt Distributor, which receives interrupts + * from system devices and sends them to the Interrupt Controllers. + * + * o There is one CPU Interface per CPU, which sends interrupts sent + * by the Distributor, and interrupts generated locally, to the + * associated CPU. + * + * Note that IRQs 0-31 are special - they are local to each CPU. + * As such, the enable set/clear, pending set/clear and active bit + * registers are banked per-cpu for these sources. + */ +#include <linux/init.h> +#include <linux/kernel.h> +#include <linux/list.h> +#include <linux/smp.h> + +#include <asm/irq.h> +#include <asm/io.h> +#include <asm/mach/irq.h> +#include <asm/hardware/gic.h> + +static void __iomem *gic_dist_base; +static void __iomem *gic_cpu_base; + +/* + * Routines to acknowledge, disable and enable interrupts + * + * Linux assumes that when we're done with an interrupt we need to + * unmask it, in the same way we need to unmask an interrupt when + * we first enable it. + * + * The GIC has a seperate notion of "end of interrupt" to re-enable + * an interrupt after handling, in order to support hardware + * prioritisation. + * + * We can make the GIC behave in the way that Linux expects by making + * our "acknowledge" routine disable the interrupt, then mark it as + * complete. + */ +static void gic_ack_irq(unsigned int irq) +{ + u32 mask = 1 << (irq % 32); + writel(mask, gic_dist_base + GIC_DIST_ENABLE_CLEAR + (irq / 32) * 4); + writel(irq, gic_cpu_base + GIC_CPU_EOI); +} + +static void gic_mask_irq(unsigned int irq) +{ + u32 mask = 1 << (irq % 32); + writel(mask, gic_dist_base + GIC_DIST_ENABLE_CLEAR + (irq / 32) * 4); +} + +static void gic_unmask_irq(unsigned int irq) +{ + u32 mask = 1 << (irq % 32); + writel(mask, gic_dist_base + GIC_DIST_ENABLE_SET + (irq / 32) * 4); +} + +static void gic_set_cpu(struct irqdesc *desc, unsigned int irq, unsigned int cpu) +{ + void __iomem *reg = gic_dist_base + GIC_DIST_TARGET + (irq & ~3); + unsigned int shift = (irq % 4) * 8; + u32 val; + + val = readl(reg) & ~(0xff << shift); + val |= 1 << (cpu + shift); + writel(val, reg); +} + +static struct irqchip gic_chip = { + .ack = gic_ack_irq, + .mask = gic_mask_irq, + .unmask = gic_unmask_irq, +#ifdef CONFIG_SMP + .set_cpu = gic_set_cpu, +#endif +}; + +void __init gic_dist_init(void __iomem *base) +{ + unsigned int max_irq, i; + u32 cpumask = 1 << smp_processor_id(); + + cpumask |= cpumask << 8; + cpumask |= cpumask << 16; + + gic_dist_base = base; + + writel(0, base + GIC_DIST_CTRL); + + /* + * Find out how many interrupts are supported. + */ + max_irq = readl(base + GIC_DIST_CTR) & 0x1f; + max_irq = (max_irq + 1) * 32; + + /* + * The GIC only supports up to 1020 interrupt sources. + * Limit this to either the architected maximum, or the + * platform maximum. + */ + if (max_irq > max(1020, NR_IRQS)) + max_irq = max(1020, NR_IRQS); + + /* + * Set all global interrupts to be level triggered, active low. + */ + for (i = 32; i < max_irq; i += 16) + writel(0, base + GIC_DIST_CONFIG + i * 4 / 16); + + /* + * Set all global interrupts to this CPU only. + */ + for (i = 32; i < max_irq; i += 4) + writel(cpumask, base + GIC_DIST_TARGET + i * 4 / 4); + + /* + * Set priority on all interrupts. + */ + for (i = 0; i < max_irq; i += 4) + writel(0xa0a0a0a0, base + GIC_DIST_PRI + i * 4 / 4); + + /* + * Disable all interrupts. + */ + for (i = 0; i < max_irq; i += 32) + writel(0xffffffff, base + GIC_DIST_ENABLE_CLEAR + i * 4 / 32); + + /* + * Setup the Linux IRQ subsystem. + */ + for (i = 29; i < max_irq; i++) { + set_irq_chip(i, &gic_chip); + set_irq_handler(i, do_level_IRQ); + set_irq_flags(i, IRQF_VALID | IRQF_PROBE); + } + + writel(1, base + GIC_DIST_CTRL); +} + +void __cpuinit gic_cpu_init(void __iomem *base) +{ + gic_cpu_base = base; + writel(0xf0, base + GIC_CPU_PRIMASK); + writel(1, base + GIC_CPU_CTRL); +} + +#ifdef CONFIG_SMP +void gic_raise_softirq(cpumask_t cpumask, unsigned int irq) +{ + unsigned long map = *cpus_addr(cpumask); + + writel(map << 16 | irq, gic_dist_base + GIC_DIST_SOFTINT); +} +#endif diff --git a/arch/arm/kernel/signal.c b/arch/arm/kernel/signal.c index 5e435e42dacd..a94d75fef598 100644 --- a/arch/arm/kernel/signal.c +++ b/arch/arm/kernel/signal.c @@ -658,11 +658,12 @@ handle_signal(unsigned long sig, struct k_sigaction *ka, /* * Block the signal if we were unsuccessful. */ - if (ret != 0 || !(ka->sa.sa_flags & SA_NODEFER)) { + if (ret != 0) { spin_lock_irq(&tsk->sighand->siglock); sigorsets(&tsk->blocked, &tsk->blocked, &ka->sa.sa_mask); - sigaddset(&tsk->blocked, sig); + if (!(ka->sa.sa_flags & SA_NODEFER)) + sigaddset(&tsk->blocked, sig); recalc_sigpending(); spin_unlock_irq(&tsk->sighand->siglock); } diff --git a/arch/arm/mach-ixp4xx/coyote-setup.c b/arch/arm/mach-ixp4xx/coyote-setup.c index 7f58afb27e71..411ea9996190 100644 --- a/arch/arm/mach-ixp4xx/coyote-setup.c +++ b/arch/arm/mach-ixp4xx/coyote-setup.c @@ -36,7 +36,7 @@ static struct flash_platform_data coyote_flash_data = { static struct resource coyote_flash_resource = { .start = COYOTE_FLASH_BASE, - .end = COYOTE_FLASH_BASE + COYOTE_FLASH_SIZE, + .end = COYOTE_FLASH_BASE + COYOTE_FLASH_SIZE - 1, .flags = IORESOURCE_MEM, }; diff --git a/arch/arm/mach-ixp4xx/gtwx5715-setup.c b/arch/arm/mach-ixp4xx/gtwx5715-setup.c index 65e356bd10d6..333459d6aa46 100644 --- a/arch/arm/mach-ixp4xx/gtwx5715-setup.c +++ b/arch/arm/mach-ixp4xx/gtwx5715-setup.c @@ -114,7 +114,7 @@ static struct flash_platform_data gtwx5715_flash_data = { static struct resource gtwx5715_flash_resource = { .start = GTWX5715_FLASH_BASE, - .end = GTWX5715_FLASH_BASE + GTWX5715_FLASH_SIZE, + .end = GTWX5715_FLASH_BASE + GTWX5715_FLASH_SIZE - 1, .flags = IORESOURCE_MEM, }; diff --git a/arch/arm/mach-ixp4xx/ixdp425-setup.c b/arch/arm/mach-ixp4xx/ixdp425-setup.c index 4633470a6a37..fa0646c8693b 100644 --- a/arch/arm/mach-ixp4xx/ixdp425-setup.c +++ b/arch/arm/mach-ixp4xx/ixdp425-setup.c @@ -36,7 +36,7 @@ static struct flash_platform_data ixdp425_flash_data = { static struct resource ixdp425_flash_resource = { .start = IXDP425_FLASH_BASE, - .end = IXDP425_FLASH_BASE + IXDP425_FLASH_SIZE, + .end = IXDP425_FLASH_BASE + IXDP425_FLASH_SIZE - 1, .flags = IORESOURCE_MEM, }; diff --git a/arch/arm/mach-sa1100/assabet.c b/arch/arm/mach-sa1100/assabet.c index 4d4d303ee3a8..24687f511bf5 100644 --- a/arch/arm/mach-sa1100/assabet.c +++ b/arch/arm/mach-sa1100/assabet.c @@ -35,6 +35,7 @@ #include <asm/mach/map.h> #include <asm/mach/serial_sa1100.h> #include <asm/arch/assabet.h> +#include <asm/arch/mcp.h> #include "generic.h" @@ -198,6 +199,11 @@ static struct irda_platform_data assabet_irda_data = { .set_speed = assabet_irda_set_speed, }; +static struct mcp_plat_data assabet_mcp_data = { + .mccr0 = MCCR0_ADM, + .sclk_rate = 11981000, +}; + static void __init assabet_init(void) { /* @@ -246,6 +252,7 @@ static void __init assabet_init(void) sa11x0_set_flash_data(&assabet_flash_data, assabet_flash_resources, ARRAY_SIZE(assabet_flash_resources)); sa11x0_set_irda_data(&assabet_irda_data); + sa11x0_set_mcp_data(&assabet_mcp_data); } /* diff --git a/arch/arm/mach-sa1100/cerf.c b/arch/arm/mach-sa1100/cerf.c index 0aa918e24c31..9484be7dc671 100644 --- a/arch/arm/mach-sa1100/cerf.c +++ b/arch/arm/mach-sa1100/cerf.c @@ -29,6 +29,7 @@ #include <asm/mach/serial_sa1100.h> #include <asm/arch/cerf.h> +#include <asm/arch/mcp.h> #include "generic.h" static struct resource cerfuart2_resources[] = { @@ -116,10 +117,16 @@ static void __init cerf_map_io(void) GPDR |= CERF_GPIO_CF_RESET; } +static struct mcp_plat_data cerf_mcp_data = { + .mccr0 = MCCR0_ADM, + .sclk_rate = 11981000, +}; + static void __init cerf_init(void) { platform_add_devices(cerf_devices, ARRAY_SIZE(cerf_devices)); sa11x0_set_flash_data(&cerf_flash_data, &cerf_flash_resource, 1); + sa11x0_set_mcp_data(&cerf_mcp_data); } MACHINE_START(CERF, "Intrinsyc CerfBoard/CerfCube") diff --git a/arch/arm/mach-sa1100/generic.c b/arch/arm/mach-sa1100/generic.c index 95ae217be1bc..3f1e358455e5 100644 --- a/arch/arm/mach-sa1100/generic.c +++ b/arch/arm/mach-sa1100/generic.c @@ -221,6 +221,11 @@ static struct platform_device sa11x0mcp_device = { .resource = sa11x0mcp_resources, }; +void sa11x0_set_mcp_data(struct mcp_plat_data *data) +{ + sa11x0mcp_device.dev.platform_data = data; +} + static struct resource sa11x0ssp_resources[] = { [0] = { .start = 0x80070000, diff --git a/arch/arm/mach-sa1100/generic.h b/arch/arm/mach-sa1100/generic.h index bfe41da9923e..279e3afa3c39 100644 --- a/arch/arm/mach-sa1100/generic.h +++ b/arch/arm/mach-sa1100/generic.h @@ -34,5 +34,8 @@ struct resource; extern void sa11x0_set_flash_data(struct flash_platform_data *flash, struct resource *res, int nr); +struct sa11x0_ssp_plat_ops; +extern void sa11x0_set_ssp_data(struct sa11x0_ssp_plat_ops *ops); + struct irda_platform_data; void sa11x0_set_irda_data(struct irda_platform_data *irda); diff --git a/arch/arm/mach-sa1100/lart.c b/arch/arm/mach-sa1100/lart.c index 870b488aeda4..ed6744d480af 100644 --- a/arch/arm/mach-sa1100/lart.c +++ b/arch/arm/mach-sa1100/lart.c @@ -13,12 +13,23 @@ #include <asm/mach/arch.h> #include <asm/mach/map.h> #include <asm/mach/serial_sa1100.h> +#include <asm/arch/mcp.h> #include "generic.h" #warning "include/asm/arch-sa1100/ide.h needs fixing for lart" +static struct mcp_plat_data lart_mcp_data = { + .mccr0 = MCCR0_ADM, + .sclk_rate = 11981000, +}; + +static void __init lart_init(void) +{ + sa11x0_set_mcp_data(&lart_mcp_data); +} + static struct map_desc lart_io_desc[] __initdata = { /* virtual physical length type */ { 0xe8000000, 0x00000000, 0x00400000, MT_DEVICE }, /* main flash memory */ @@ -47,5 +58,6 @@ MACHINE_START(LART, "LART") .boot_params = 0xc0000100, .map_io = lart_map_io, .init_irq = sa1100_init_irq, + .init_machine = lart_init, .timer = &sa1100_timer, MACHINE_END diff --git a/arch/arm/mach-sa1100/shannon.c b/arch/arm/mach-sa1100/shannon.c index 43a00359fcdd..7482288278d9 100644 --- a/arch/arm/mach-sa1100/shannon.c +++ b/arch/arm/mach-sa1100/shannon.c @@ -18,6 +18,7 @@ #include <asm/mach/flash.h> #include <asm/mach/map.h> #include <asm/mach/serial_sa1100.h> +#include <asm/arch/mcp.h> #include <asm/arch/shannon.h> #include "generic.h" @@ -52,9 +53,15 @@ static struct resource shannon_flash_resource = { .flags = IORESOURCE_MEM, }; +static struct mcp_plat_data shannon_mcp_data = { + .mccr0 = MCCR0_ADM, + .sclk_rate = 11981000, +}; + static void __init shannon_init(void) { sa11x0_set_flash_data(&shannon_flash_data, &shannon_flash_resource, 1); + sa11x0_set_mcp_data(&shannon_mcp_data); } static void __init shannon_map_io(void) diff --git a/arch/arm/mach-sa1100/simpad.c b/arch/arm/mach-sa1100/simpad.c index 77978586b126..07f6d5fd7bb0 100644 --- a/arch/arm/mach-sa1100/simpad.c +++ b/arch/arm/mach-sa1100/simpad.c @@ -23,6 +23,7 @@ #include <asm/mach/flash.h> #include <asm/mach/map.h> #include <asm/mach/serial_sa1100.h> +#include <asm/arch/mcp.h> #include <asm/arch/simpad.h> #include <linux/serial_core.h> @@ -123,6 +124,11 @@ static struct resource simpad_flash_resources [] = { } }; +static struct mcp_plat_data simpad_mcp_data = { + .mccr0 = MCCR0_ADM, + .sclk_rate = 11981000, +}; + static void __init simpad_map_io(void) @@ -157,6 +163,7 @@ static void __init simpad_map_io(void) sa11x0_set_flash_data(&simpad_flash_data, simpad_flash_resources, ARRAY_SIZE(simpad_flash_resources)); + sa11x0_set_mcp_data(&simpad_mcp_data); } static void simpad_power_off(void) |