Merge tag 'iio-for-4.7b' of git://git.kernel.org/pub/scm/linux/kernel/git/jic23/iio into staging-testing

Jonathan writes:

2nd set of new device support, features and cleanup for IIO in the 4.7 cycle.

Bit of a bumper set for new drivers but plenty of other stuff here as well!

New device support
* ad5592R ADC/DAC
  - new driver supporting ad5592r and ad5593r combined ADC/DAC and gpio chips.
* Aosong am2315 relative humidity
  - new driver with triggered buffer support in follow up patch.
* bmi160 imu
  - new driver
* bmp280
  - bmp180 support - note there is support in the misc/bmp085 driver. Intent
    is to remove that driver long term.
* invensense mpu6050
  - cleanup leading to explicit support of mpu9150 with a good few cleanups
    along the way.
* Hope RF hp03 pressure and temperature sensor.
  - new driver
* maxim DS1803 potentiometer
  - new driver
* maxim max44000 light and proximity sensor
  - new driver built in a series of steps to support pretty much everything.
* ROHM BH1780 light sensor
  - new driver. There is an existing driver in misc that this is pretty much
    intended to replace.  The discussion on whether to support the non standard
    interface of that driver is some way is continuing.
* st-gyro
  - lsm9ds0-gyro.  The accel/magn side of this will take a while longer as
    extensions to the st library are needed for cases where two types of sensor
    share a single i2c address.
* ti-adc081c
  - support the adc101c and adc121c
* Vishay VEML6070 UV sensor
  - new driver.

New features
* core
  - devm_ APIs for channel_get and channel_get_all.  The first user of these
    is the generic ADC based thermal driver.  As it is going through the
    thermal tree these will be picked up as a patch to that next cycle as that
    is how the author preferred to do it.
  - mounting matrix support.  This new core support allows devices to provide
    to userspace (typically from the device tree) allowing compensation for how
    the sensor is mounted on the device.  First examples are on UAVs but it
    has a more mundane use on typical phone where the chip may be on the front
    or the back of the circuit board and soldered at any angle. Includes
    support for this ABI in ak8975 (which has an older interface, now
    deprecated) and mpu6050.
* tools
  - add a -a option to enable all available channels in generic_buffer sample.
    Makes it somewhat easier to use.
* adis library and drivers
  - support manual self test flag clearing.  This has technically been broken
    for a very long time - result is an offset on readings as the applied field
    is on all the time.
* ak8975
  - triggered buffer support
* bmc150
  - spi support (including splitting the driver into core and i2c parts)
* bmp280
  - oversampling support.
* dht11
  - improved logging - useful to debug timing issues on this quirky device.
* st-sensors
  - read each channel invidivually as not all support the optimization of
  reading in bulk.  This is technically a fix, but will need to be backported
  if desired.
  - support open drain and shared interrupts.
* ti-adc081c
  - triggered buffer support.

Cleanups
* inkern
  - white space fix.
* ad7606
  - use the iio_device_claim_direct_mode call rather than open coding equiv.
* ad799x
  - white space fix.
* ad9523
  - unsigned -> unsigned int
* apds9660
  - brace location tidying up.
  - silence an uninitialized variable warning.
* ak8975
  - else and brace on same line fix.
* at91_adc
  - white space fixes.
* bmc150
  - use regmap stored copy of the device pointer rather than having an
    additional copy.
* bmg160
  - use regmap stored copy of the device pointer rather than having an
    additional copy.
* hid-sensors
  - white space fixes.
* mcp3422
  - white space fix.
* mma7455
  - use regmap to retrieve the device struct rather than carrying another copy
    in the private data.
* ms_sensors
  - white space fix.
* mxs-lradc
  - move current bindings out of staging - some will be shortly deprecated but
    the reality is that we have device trees out there using them so they will
    need to be supported for some time.  They accidentally got left behind
    when the driver graduated from staging.
  - white space cleanup.
  - set INPUT_PROP_DIRECT.
  - move ts config into a better function.
  - move the STMP reset out of the ADC init.
* vf610_adc
  - case label indenting fix.

3 files changed, 69 insertions, 48 deletions

diff --git a/drivers/iio/accel/bmc150-accel-core.c b/drivers/iio/accel/bmc150-accel-core.c
index 2a0735d6955d..197e693e7e7b 100644
--- a/drivers/iio/accel/bmc150-accel-core.c
+++ b/drivers/iio/accel/bmc150-accel-core.c
@@ -188,7 +188,6 @@ enum bmc150_accel_trigger_id {
 
 struct bmc150_accel_data {
 	struct regmap *regmap;
-	struct device *dev;
 	int irq;
 	struct bmc150_accel_interrupt interrupts[BMC150_ACCEL_INTERRUPTS];
 	atomic_t active_intr;
@@ -257,6 +256,7 @@ static int bmc150_accel_set_mode(struct bmc150_accel_data *data,
 				 enum bmc150_power_modes mode,
 				 int dur_us)
 {
+	struct device *dev = regmap_get_device(data->regmap);
 	int i;
 	int ret;
 	u8 lpw_bits;
@@ -280,11 +280,11 @@ static int bmc150_accel_set_mode(struct bmc150_accel_data *data,
 	lpw_bits = mode << BMC150_ACCEL_PMU_MODE_SHIFT;
 	lpw_bits |= (dur_val << BMC150_ACCEL_PMU_BIT_SLEEP_DUR_SHIFT);
 
-	dev_dbg(data->dev, "Set Mode bits %x\n", lpw_bits);
+	dev_dbg(dev, "Set Mode bits %x\n", lpw_bits);
 
 	ret = regmap_write(data->regmap, BMC150_ACCEL_REG_PMU_LPW, lpw_bits);
 	if (ret < 0) {
-		dev_err(data->dev, "Error writing reg_pmu_lpw\n");
+		dev_err(dev, "Error writing reg_pmu_lpw\n");
 		return ret;
 	}
 
@@ -317,23 +317,24 @@ static int bmc150_accel_set_bw(struct bmc150_accel_data *data, int val,
 
 static int bmc150_accel_update_slope(struct bmc150_accel_data *data)
 {
+	struct device *dev = regmap_get_device(data->regmap);
 	int ret;
 
 	ret = regmap_write(data->regmap, BMC150_ACCEL_REG_INT_6,
 					data->slope_thres);
 	if (ret < 0) {
-		dev_err(data->dev, "Error writing reg_int_6\n");
+		dev_err(dev, "Error writing reg_int_6\n");
 		return ret;
 	}
 
 	ret = regmap_update_bits(data->regmap, BMC150_ACCEL_REG_INT_5,
 				 BMC150_ACCEL_SLOPE_DUR_MASK, data->slope_dur);
 	if (ret < 0) {
-		dev_err(data->dev, "Error updating reg_int_5\n");
+		dev_err(dev, "Error updating reg_int_5\n");
 		return ret;
 	}
 
-	dev_dbg(data->dev, "%s: %x %x\n", __func__, data->slope_thres,
+	dev_dbg(dev, "%s: %x %x\n", __func__, data->slope_thres,
 		data->slope_dur);
 
 	return ret;
@@ -379,20 +380,21 @@ static int bmc150_accel_get_startup_times(struct bmc150_accel_data *data)
 
 static int bmc150_accel_set_power_state(struct bmc150_accel_data *data, bool on)
 {
+	struct device *dev = regmap_get_device(data->regmap);
 	int ret;
 
 	if (on) {
-		ret = pm_runtime_get_sync(data->dev);
+		ret = pm_runtime_get_sync(dev);
 	} else {
-		pm_runtime_mark_last_busy(data->dev);
-		ret = pm_runtime_put_autosuspend(data->dev);
+		pm_runtime_mark_last_busy(dev);
+		ret = pm_runtime_put_autosuspend(dev);
 	}
 
 	if (ret < 0) {
-		dev_err(data->dev,
+		dev_err(dev,
 			"Failed: bmc150_accel_set_power_state for %d\n", on);
 		if (on)
-			pm_runtime_put_noidle(data->dev);
+			pm_runtime_put_noidle(dev);
 
 		return ret;
 	}
@@ -446,6 +448,7 @@ static void bmc150_accel_interrupts_setup(struct iio_dev *indio_dev,
 static int bmc150_accel_set_interrupt(struct bmc150_accel_data *data, int i,
 				      bool state)
 {
+	struct device *dev = regmap_get_device(data->regmap);
 	struct bmc150_accel_interrupt *intr = &data->interrupts[i];
 	const struct bmc150_accel_interrupt_info *info = intr->info;
 	int ret;
@@ -475,7 +478,7 @@ static int bmc150_accel_set_interrupt(struct bmc150_accel_data *data, int i,
 	ret = regmap_update_bits(data->regmap, info->map_reg, info->map_bitmask,
 				 (state ? info->map_bitmask : 0));
 	if (ret < 0) {
-		dev_err(data->dev, "Error updating reg_int_map\n");
+		dev_err(dev, "Error updating reg_int_map\n");
 		goto out_fix_power_state;
 	}
 
@@ -483,7 +486,7 @@ static int bmc150_accel_set_interrupt(struct bmc150_accel_data *data, int i,
 	ret = regmap_update_bits(data->regmap, info->en_reg, info->en_bitmask,
 				 (state ? info->en_bitmask : 0));
 	if (ret < 0) {
-		dev_err(data->dev, "Error updating reg_int_en\n");
+		dev_err(dev, "Error updating reg_int_en\n");
 		goto out_fix_power_state;
 	}
 
@@ -501,6 +504,7 @@ out_fix_power_state:
 
 static int bmc150_accel_set_scale(struct bmc150_accel_data *data, int val)
 {
+	struct device *dev = regmap_get_device(data->regmap);
 	int ret, i;
 
 	for (i = 0; i < ARRAY_SIZE(data->chip_info->scale_table); ++i) {
@@ -509,8 +513,7 @@ static int bmc150_accel_set_scale(struct bmc150_accel_data *data, int val)
 				     BMC150_ACCEL_REG_PMU_RANGE,
 				     data->chip_info->scale_table[i].reg_range);
 			if (ret < 0) {
-				dev_err(data->dev,
-					"Error writing pmu_range\n");
+				dev_err(dev, "Error writing pmu_range\n");
 				return ret;
 			}
 
@@ -524,6 +527,7 @@ static int bmc150_accel_set_scale(struct bmc150_accel_data *data, int val)
 
 static int bmc150_accel_get_temp(struct bmc150_accel_data *data, int *val)
 {
+	struct device *dev = regmap_get_device(data->regmap);
 	int ret;
 	unsigned int value;
 
@@ -531,7 +535,7 @@ static int bmc150_accel_get_temp(struct bmc150_accel_data *data, int *val)
 
 	ret = regmap_read(data->regmap, BMC150_ACCEL_REG_TEMP, &value);
 	if (ret < 0) {
-		dev_err(data->dev, "Error reading reg_temp\n");
+		dev_err(dev, "Error reading reg_temp\n");
 		mutex_unlock(&data->mutex);
 		return ret;
 	}
@@ -546,6 +550,7 @@ static int bmc150_accel_get_axis(struct bmc150_accel_data *data,
 				 struct iio_chan_spec const *chan,
 				 int *val)
 {
+	struct device *dev = regmap_get_device(data->regmap);
 	int ret;
 	int axis = chan->scan_index;
 	__le16 raw_val;
@@ -560,7 +565,7 @@ static int bmc150_accel_get_axis(struct bmc150_accel_data *data,
 	ret = regmap_bulk_read(data->regmap, BMC150_ACCEL_AXIS_TO_REG(axis),
 			       &raw_val, sizeof(raw_val));
 	if (ret < 0) {
-		dev_err(data->dev, "Error reading axis %d\n", axis);
+		dev_err(dev, "Error reading axis %d\n", axis);
 		bmc150_accel_set_power_state(data, false);
 		mutex_unlock(&data->mutex);
 		return ret;
@@ -832,6 +837,7 @@ static int bmc150_accel_set_watermark(struct iio_dev *indio_dev, unsigned val)
 static int bmc150_accel_fifo_transfer(struct bmc150_accel_data *data,
 				      char *buffer, int samples)
 {
+	struct device *dev = regmap_get_device(data->regmap);
 	int sample_length = 3 * 2;
 	int ret;
 	int total_length = samples * sample_length;
@@ -855,7 +861,8 @@ static int bmc150_accel_fifo_transfer(struct bmc150_accel_data *data,
 	}
 
 	if (ret)
-		dev_err(data->dev, "Error transferring data from fifo in single steps of %zu\n",
+		dev_err(dev,
+			"Error transferring data from fifo in single steps of %zu\n",
 			step);
 
 	return ret;
@@ -865,6 +872,7 @@ static int __bmc150_accel_fifo_flush(struct iio_dev *indio_dev,
 				     unsigned samples, bool irq)
 {
 	struct bmc150_accel_data *data = iio_priv(indio_dev);
+	struct device *dev = regmap_get_device(data->regmap);
 	int ret, i;
 	u8 count;
 	u16 buffer[BMC150_ACCEL_FIFO_LENGTH * 3];
@@ -874,7 +882,7 @@ static int __bmc150_accel_fifo_flush(struct iio_dev *indio_dev,
 
 	ret = regmap_read(data->regmap, BMC150_ACCEL_REG_FIFO_STATUS, &val);
 	if (ret < 0) {
-		dev_err(data->dev, "Error reading reg_fifo_status\n");
+		dev_err(dev, "Error reading reg_fifo_status\n");
 		return ret;
 	}
 
@@ -1136,6 +1144,7 @@ static int bmc150_accel_trig_try_reen(struct iio_trigger *trig)
 {
 	struct bmc150_accel_trigger *t = iio_trigger_get_drvdata(trig);
 	struct bmc150_accel_data *data = t->data;
+	struct device *dev = regmap_get_device(data->regmap);
 	int ret;
 
 	/* new data interrupts don't need ack */
@@ -1149,8 +1158,7 @@ static int bmc150_accel_trig_try_reen(struct iio_trigger *trig)
 			   BMC150_ACCEL_INT_MODE_LATCH_RESET);
 	mutex_unlock(&data->mutex);
 	if (ret < 0) {
-		dev_err(data->dev,
-			"Error writing reg_int_rst_latch\n");
+		dev_err(dev, "Error writing reg_int_rst_latch\n");
 		return ret;
 	}
 
@@ -1201,13 +1209,14 @@ static const struct iio_trigger_ops bmc150_accel_trigger_ops = {
 static int bmc150_accel_handle_roc_event(struct iio_dev *indio_dev)
 {
 	struct bmc150_accel_data *data = iio_priv(indio_dev);
+	struct device *dev = regmap_get_device(data->regmap);
 	int dir;
 	int ret;
 	unsigned int val;
 
 	ret = regmap_read(data->regmap, BMC150_ACCEL_REG_INT_STATUS_2, &val);
 	if (ret < 0) {
-		dev_err(data->dev, "Error reading reg_int_status_2\n");
+		dev_err(dev, "Error reading reg_int_status_2\n");
 		return ret;
 	}
 
@@ -1250,6 +1259,7 @@ static irqreturn_t bmc150_accel_irq_thread_handler(int irq, void *private)
 {
 	struct iio_dev *indio_dev = private;
 	struct bmc150_accel_data *data = iio_priv(indio_dev);
+	struct device *dev = regmap_get_device(data->regmap);
 	bool ack = false;
 	int ret;
 
@@ -1273,7 +1283,7 @@ static irqreturn_t bmc150_accel_irq_thread_handler(int irq, void *private)
 				   BMC150_ACCEL_INT_MODE_LATCH_INT |
 				   BMC150_ACCEL_INT_MODE_LATCH_RESET);
 		if (ret)
-			dev_err(data->dev, "Error writing reg_int_rst_latch\n");
+			dev_err(dev, "Error writing reg_int_rst_latch\n");
 
 		ret = IRQ_HANDLED;
 	} else {
@@ -1344,13 +1354,14 @@ static void bmc150_accel_unregister_triggers(struct bmc150_accel_data *data,
 static int bmc150_accel_triggers_setup(struct iio_dev *indio_dev,
 				       struct bmc150_accel_data *data)
 {
+	struct device *dev = regmap_get_device(data->regmap);
 	int i, ret;
 
 	for (i = 0; i < BMC150_ACCEL_TRIGGERS; i++) {
 		struct bmc150_accel_trigger *t = &data->triggers[i];
 
-		t->indio_trig = devm_iio_trigger_alloc(data->dev,
-					       bmc150_accel_triggers[i].name,
+		t->indio_trig = devm_iio_trigger_alloc(dev,
+					bmc150_accel_triggers[i].name,
 						       indio_dev->name,
 						       indio_dev->id);
 		if (!t->indio_trig) {
@@ -1358,7 +1369,7 @@ static int bmc150_accel_triggers_setup(struct iio_dev *indio_dev,
 			break;
 		}
 
-		t->indio_trig->dev.parent = data->dev;
+		t->indio_trig->dev.parent = dev;
 		t->indio_trig->ops = &bmc150_accel_trigger_ops;
 		t->intr = bmc150_accel_triggers[i].intr;
 		t->data = data;
@@ -1382,12 +1393,13 @@ static int bmc150_accel_triggers_setup(struct iio_dev *indio_dev,
 
 static int bmc150_accel_fifo_set_mode(struct bmc150_accel_data *data)
 {
+	struct device *dev = regmap_get_device(data->regmap);
 	u8 reg = BMC150_ACCEL_REG_FIFO_CONFIG1;
 	int ret;
 
 	ret = regmap_write(data->regmap, reg, data->fifo_mode);
 	if (ret < 0) {
-		dev_err(data->dev, "Error writing reg_fifo_config1\n");
+		dev_err(dev, "Error writing reg_fifo_config1\n");
 		return ret;
 	}
 
@@ -1397,7 +1409,7 @@ static int bmc150_accel_fifo_set_mode(struct bmc150_accel_data *data)
 	ret = regmap_write(data->regmap, BMC150_ACCEL_REG_FIFO_CONFIG0,
 			   data->watermark);
 	if (ret < 0)
-		dev_err(data->dev, "Error writing reg_fifo_config0\n");
+		dev_err(dev, "Error writing reg_fifo_config0\n");
 
 	return ret;
 }
@@ -1481,17 +1493,17 @@ static const struct iio_buffer_setup_ops bmc150_accel_buffer_ops = {
 
 static int bmc150_accel_chip_init(struct bmc150_accel_data *data)
 {
+	struct device *dev = regmap_get_device(data->regmap);
 	int ret, i;
 	unsigned int val;
 
 	ret = regmap_read(data->regmap, BMC150_ACCEL_REG_CHIP_ID, &val);
 	if (ret < 0) {
-		dev_err(data->dev,
-			"Error: Reading chip id\n");
+		dev_err(dev, "Error: Reading chip id\n");
 		return ret;
 	}
 
-	dev_dbg(data->dev, "Chip Id %x\n", val);
+	dev_dbg(dev, "Chip Id %x\n", val);
 	for (i = 0; i < ARRAY_SIZE(bmc150_accel_chip_info_tbl); i++) {
 		if (bmc150_accel_chip_info_tbl[i].chip_id == val) {
 			data->chip_info = &bmc150_accel_chip_info_tbl[i];
@@ -1500,7 +1512,7 @@ static int bmc150_accel_chip_init(struct bmc150_accel_data *data)
 	}
 
 	if (!data->chip_info) {
-		dev_err(data->dev, "Invalid chip %x\n", val);
+		dev_err(dev, "Invalid chip %x\n", val);
 		return -ENODEV;
 	}
 
@@ -1517,8 +1529,7 @@ static int bmc150_accel_chip_init(struct bmc150_accel_data *data)
 	ret = regmap_write(data->regmap, BMC150_ACCEL_REG_PMU_RANGE,
 			   BMC150_ACCEL_DEF_RANGE_4G);
 	if (ret < 0) {
-		dev_err(data->dev,
-					"Error writing reg_pmu_range\n");
+		dev_err(dev, "Error writing reg_pmu_range\n");
 		return ret;
 	}
 
@@ -1536,8 +1547,7 @@ static int bmc150_accel_chip_init(struct bmc150_accel_data *data)
 			   BMC150_ACCEL_INT_MODE_LATCH_INT |
 			   BMC150_ACCEL_INT_MODE_LATCH_RESET);
 	if (ret < 0) {
-		dev_err(data->dev,
-			"Error writing reg_int_rst_latch\n");
+		dev_err(dev, "Error writing reg_int_rst_latch\n");
 		return ret;
 	}
 
@@ -1557,7 +1567,6 @@ int bmc150_accel_core_probe(struct device *dev, struct regmap *regmap, int irq,
 
 	data = iio_priv(indio_dev);
 	dev_set_drvdata(dev, indio_dev);
-	data->dev = dev;
 	data->irq = irq;
 
 	data->regmap = regmap;
@@ -1581,13 +1590,13 @@ int bmc150_accel_core_probe(struct device *dev, struct regmap *regmap, int irq,
 					 bmc150_accel_trigger_handler,
 					 &bmc150_accel_buffer_ops);
 	if (ret < 0) {
-		dev_err(data->dev, "Failed: iio triggered buffer setup\n");
+		dev_err(dev, "Failed: iio triggered buffer setup\n");
 		return ret;
 	}
 
 	if (data->irq > 0) {
 		ret = devm_request_threaded_irq(
-						data->dev, data->irq,
+						dev, data->irq,
 						bmc150_accel_irq_handler,
 						bmc150_accel_irq_thread_handler,
 						IRQF_TRIGGER_RISING,
@@ -1605,7 +1614,7 @@ int bmc150_accel_core_probe(struct device *dev, struct regmap *regmap, int irq,
 		ret = regmap_write(data->regmap, BMC150_ACCEL_REG_INT_RST_LATCH,
 				   BMC150_ACCEL_INT_MODE_LATCH_RESET);
 		if (ret < 0) {
-			dev_err(data->dev, "Error writing reg_int_rst_latch\n");
+			dev_err(dev, "Error writing reg_int_rst_latch\n");
 			goto err_buffer_cleanup;
 		}
 
@@ -1654,9 +1663,9 @@ int bmc150_accel_core_remove(struct device *dev)
 
 	iio_device_unregister(indio_dev);
 
-	pm_runtime_disable(data->dev);
-	pm_runtime_set_suspended(data->dev);
-	pm_runtime_put_noidle(data->dev);
+	pm_runtime_disable(dev);
+	pm_runtime_set_suspended(dev);
+	pm_runtime_put_noidle(dev);
 
 	bmc150_accel_unregister_triggers(data, BMC150_ACCEL_TRIGGERS - 1);
 
@@ -1705,7 +1714,7 @@ static int bmc150_accel_runtime_suspend(struct device *dev)
 	struct bmc150_accel_data *data = iio_priv(indio_dev);
 	int ret;
 
-	dev_dbg(data->dev,  __func__);
+	dev_dbg(dev,  __func__);
 	ret = bmc150_accel_set_mode(data, BMC150_ACCEL_SLEEP_MODE_SUSPEND, 0);
 	if (ret < 0)
 		return -EAGAIN;
@@ -1720,7 +1729,7 @@ static int bmc150_accel_runtime_resume(struct device *dev)
 	int ret;
 	int sleep_val;
 
-	dev_dbg(data->dev,  __func__);
+	dev_dbg(dev,  __func__);
 
 	ret = bmc150_accel_set_mode(data, BMC150_ACCEL_SLEEP_MODE_NORMAL, 0);
 	if (ret < 0)
diff --git a/drivers/iio/accel/mma7455_core.c b/drivers/iio/accel/mma7455_core.c
index c633cc2c0789..c902f54c23f5 100644
--- a/drivers/iio/accel/mma7455_core.c
+++ b/drivers/iio/accel/mma7455_core.c
@@ -55,11 +55,11 @@
 
 struct mma7455_data {
 	struct regmap *regmap;
-	struct device *dev;
 };
 
 static int mma7455_drdy(struct mma7455_data *mma7455)
 {
+	struct device *dev = regmap_get_device(mma7455->regmap);
 	unsigned int reg;
 	int tries = 3;
 	int ret;
@@ -75,7 +75,7 @@ static int mma7455_drdy(struct mma7455_data *mma7455)
 		msleep(20);
 	}
 
-	dev_warn(mma7455->dev, "data not ready\n");
+	dev_warn(dev, "data not ready\n");
 
 	return -EIO;
 }
@@ -260,7 +260,6 @@ int mma7455_core_probe(struct device *dev, struct regmap *regmap,
 	dev_set_drvdata(dev, indio_dev);
 	mma7455 = iio_priv(indio_dev);
 	mma7455->regmap = regmap;
-	mma7455->dev = dev;
 
 	indio_dev->info = &mma7455_info;
 	indio_dev->name = name;
diff --git a/drivers/iio/accel/st_accel_core.c b/drivers/iio/accel/st_accel_core.c
index fee32e3d7a05..dc73f2d85e6d 100644
--- a/drivers/iio/accel/st_accel_core.c
+++ b/drivers/iio/accel/st_accel_core.c
@@ -99,6 +99,8 @@
 #define ST_ACCEL_2_DRDY_IRQ_INT2_MASK		0x10
 #define ST_ACCEL_2_IHL_IRQ_ADDR			0x22
 #define ST_ACCEL_2_IHL_IRQ_MASK			0x80
+#define ST_ACCEL_2_OD_IRQ_ADDR			0x22
+#define ST_ACCEL_2_OD_IRQ_MASK			0x40
 #define ST_ACCEL_2_MULTIREAD_BIT		true
 
 /* CUSTOM VALUES FOR SENSOR 3 */
@@ -180,6 +182,8 @@
 #define ST_ACCEL_5_DRDY_IRQ_INT2_MASK		0x20
 #define ST_ACCEL_5_IHL_IRQ_ADDR			0x22
 #define ST_ACCEL_5_IHL_IRQ_MASK			0x80
+#define ST_ACCEL_5_OD_IRQ_ADDR			0x22
+#define ST_ACCEL_5_OD_IRQ_MASK			0x40
 #define ST_ACCEL_5_IG1_EN_ADDR			0x21
 #define ST_ACCEL_5_IG1_EN_MASK			0x08
 #define ST_ACCEL_5_MULTIREAD_BIT		false
@@ -332,6 +336,7 @@ static const struct st_sensor_settings st_accel_sensors_settings[] = {
 			.mask_int2 = ST_ACCEL_1_DRDY_IRQ_INT2_MASK,
 			.addr_ihl = ST_ACCEL_1_IHL_IRQ_ADDR,
 			.mask_ihl = ST_ACCEL_1_IHL_IRQ_MASK,
+			.addr_stat_drdy = ST_SENSORS_DEFAULT_STAT_ADDR,
 		},
 		.multi_read_bit = ST_ACCEL_1_MULTIREAD_BIT,
 		.bootime = 2,
@@ -397,6 +402,9 @@ static const struct st_sensor_settings st_accel_sensors_settings[] = {
 			.mask_int2 = ST_ACCEL_2_DRDY_IRQ_INT2_MASK,
 			.addr_ihl = ST_ACCEL_2_IHL_IRQ_ADDR,
 			.mask_ihl = ST_ACCEL_2_IHL_IRQ_MASK,
+			.addr_od = ST_ACCEL_2_OD_IRQ_ADDR,
+			.mask_od = ST_ACCEL_2_OD_IRQ_MASK,
+			.addr_stat_drdy = ST_SENSORS_DEFAULT_STAT_ADDR,
 		},
 		.multi_read_bit = ST_ACCEL_2_MULTIREAD_BIT,
 		.bootime = 2,
@@ -474,6 +482,7 @@ static const struct st_sensor_settings st_accel_sensors_settings[] = {
 			.mask_int2 = ST_ACCEL_3_DRDY_IRQ_INT2_MASK,
 			.addr_ihl = ST_ACCEL_3_IHL_IRQ_ADDR,
 			.mask_ihl = ST_ACCEL_3_IHL_IRQ_MASK,
+			.addr_stat_drdy = ST_SENSORS_DEFAULT_STAT_ADDR,
 			.ig1 = {
 				.en_addr = ST_ACCEL_3_IG1_EN_ADDR,
 				.en_mask = ST_ACCEL_3_IG1_EN_MASK,
@@ -532,6 +541,7 @@ static const struct st_sensor_settings st_accel_sensors_settings[] = {
 		.drdy_irq = {
 			.addr = ST_ACCEL_4_DRDY_IRQ_ADDR,
 			.mask_int1 = ST_ACCEL_4_DRDY_IRQ_INT1_MASK,
+			.addr_stat_drdy = ST_SENSORS_DEFAULT_STAT_ADDR,
 		},
 		.multi_read_bit = ST_ACCEL_4_MULTIREAD_BIT,
 		.bootime = 2, /* guess */
@@ -583,6 +593,9 @@ static const struct st_sensor_settings st_accel_sensors_settings[] = {
 			.mask_int2 = ST_ACCEL_5_DRDY_IRQ_INT2_MASK,
 			.addr_ihl = ST_ACCEL_5_IHL_IRQ_ADDR,
 			.mask_ihl = ST_ACCEL_5_IHL_IRQ_MASK,
+			.addr_od = ST_ACCEL_5_OD_IRQ_ADDR,
+			.mask_od = ST_ACCEL_5_OD_IRQ_MASK,
+			.addr_stat_drdy = ST_SENSORS_DEFAULT_STAT_ADDR,
 		},
 		.multi_read_bit = ST_ACCEL_5_MULTIREAD_BIT,
 		.bootime = 2, /* guess */