Merge tag 'mmc-v5.8' of git://git.kernel.org/pub/scm/linux/kernel/git/ulfh/mmc

Pull MMC updates from Ulf Hansson:
 "MMC core:
   - Enable erase/discard/trim support for all (e)MMC/SD hosts
   - Export information through sysfs about enhanced RPMB support (eMMC v5.1+)
   - Align the initialization commands for SDIO cards
   - Fix SDIO initialization to prevent memory leaks and NULL pointer errors
   - Do not export undefined MMC_NAME/MODALIAS for SDIO cards
   - Export device/vendor field from common CIS for SDIO cards
   - Move SDIO IDs from functional drivers to the common SDIO header
   - Introduce the ->request_atomic() host ops

  MMC host:
   - Improve support for HW busy signaling for several hosts
   - Converting some DT bindings to the json-schema
   - meson-mx-sdhc: Add driver and DT doc for the Amlogic Meson SDHC controller
   - meson-mx-sdio: Run a soft reset to recover from timeout/CRC error
   - mmci: Convert to use mmc_regulator_set_vqmmc()
   - mmci_stm32_sdmmc: Fix a couple of DMA bugs
   - mmci_stm32_sdmmc: Fix power on issue
   - renesas,mmcif,sdhci: Document r8a7742 DT bindings
   - renesas_sdhi: Add support for M3-W ES1.2 and 1.3 revisions
   - renesas_sdhi: Improvements to the TAP selection
   - renesas_sdhi/tmio: Further fixup runtime PM management at ->remove()
   - sdhci: Introduce ops to dump vendor specific registers
   - sdhci-cadence: Fix PHY write sequence
   - sdhci-esdhc-imx: Improve tunings
   - sdhci-esdhc-imx: Enable GPIO card detect as system wakeup
   - sdhci-esdhc-imx: Add HS400 support for i.MX6SLL
   - sdhci-esdhc-mcf: Add driver for the Coldfire/M5441X esdhc controller
   - m68k: mcf5441x: Add platform data to enable esdhc mmc controller
   - sdhci-msm: Improve HS400 tuning
   - sdhci-msm: Dump vendor specific registers at error
   - sdhci-msm: Add support for DLL/DDR properties provided from DT
   - sdhci-msm: Add support for the sm8250 variant
   - sdhci-msm: Add support for DVFS by converting to dev_pm_opp_set_rate()
   - sdhci-of-arasan: Add support for Intel Keem Bay variant
   - sdhci-of-arasan: Add support for Xilinx Versal SD variant
   - sdhci-of-dwcmshc: Add support for system suspend/resume
   - sdhci-of-dwcmshc: Fix UHS signaling support
   - sdhci-of-esdhc: Fix tuning for eMMC HS400 mode
   - sdhci-pci-gli: Add Genesys Logic GL9763E support
   - sdhci-sprd: Add support for the ->request_atomic() ops
   - sdhci-tegra: Avoid reading autocal timeout values when not applicable

  MEMSTICK:
   - Minor trivial update"

* tag 'mmc-v5.8' of git://git.kernel.org/pub/scm/linux/kernel/git/ulfh/mmc: (127 commits)
  dt-bindings: mmc: Convert sdhci-pxa to json-schema
  mmc: sdhci-msm: Clear tuning done flag while hs400 tuning
  mmc: core: Export device/vendor ids from Common CIS for SDIO cards
  mmc: core: Do not export MMC_NAME= and MODALIAS=mmc:block for SDIO cards
  mmc: sdhci-of-at91: fix CALCR register being rewritten
  mmc: sdhci-esdhc-imx: disable the CMD CRC check for standard tuning
  mmc: sdhci-esdhc-imx: fix the mask for tuning start point
  mmc: host: sdhci-esdhc-imx: add wakeup feature for GPIO CD pin
  mmc: mmci_sdmmc: fix DMA API warning max segment size
  mmc: mmci_sdmmc: fix DMA API warning overlapping mappings
  mmc: sdhci-of-arasan: Add support for Intel Keem Bay
  dt-bindings: mmc: arasan: Add compatible strings for Intel Keem Bay
  mmc: sdhci-cadence: fix PHY write
  mmc: sdio: Sort all SDIO IDs in common include file
  mmc: sdio: Fix Cypress SDIO IDs macros in common include file
  mmc: sdio: Move SDIO IDs from b43-sdio driver to common include file
  mmc: sdio: Move SDIO IDs from ath10k driver to common include file
  mmc: sdio: Move SDIO IDs from ath6kl driver to common include file
  mmc: sdio: Move SDIO IDs from smssdio driver to common include file
  mmc: sdio: Move SDIO IDs from btmtksdio driver to common include file
  ...

7 files changed, 245 insertions, 52 deletions

diff --git a/Documentation/devicetree/bindings/mmc/amlogic,meson-mx-sdhc.yaml b/Documentation/devicetree/bindings/mmc/amlogic,meson-mx-sdhc.yaml
new file mode 100644
index 000000000000..7a386a5b8fcb
--- /dev/null
+++ b/Documentation/devicetree/bindings/mmc/amlogic,meson-mx-sdhc.yaml
@@ -0,0 +1,68 @@
+# SPDX-License-Identifier: (GPL-2.0-only OR BSD-2-Clause)
+%YAML 1.2
+---
+$id: http://devicetree.org/schemas/mmc/amlogic,meson-mx-sdhc.yaml#
+$schema: http://devicetree.org/meta-schemas/core.yaml#
+
+title: Amlogic Meson SDHC controller Device Tree Bindings
+
+allOf:
+  - $ref: "mmc-controller.yaml"
+
+maintainers:
+  - Martin Blumenstingl <martin.blumenstingl@googlemail.com>
+
+description: |
+  The SDHC MMC host controller on Amlogic SoCs provides an eMMC and MMC
+  card interface with 1/4/8-bit bus width.
+  It supports eMMC spec 4.4x/4.5x including HS200 (up to 100MHz clock).
+
+properties:
+  compatible:
+    items:
+      - enum:
+        - amlogic,meson8-sdhc
+        - amlogic,meson8b-sdhc
+        - amlogic,meson8m2-sdhc
+      - const: amlogic,meson-mx-sdhc
+
+  reg:
+    minItems: 1
+
+  interrupts:
+    minItems: 1
+
+  clocks:
+    minItems: 5
+
+  clock-names:
+    items:
+      - const: clkin0
+      - const: clkin1
+      - const: clkin2
+      - const: clkin3
+      - const: pclk
+
+required:
+  - compatible
+  - reg
+  - interrupts
+  - clocks
+  - clock-names
+
+examples:
+  - |
+    #include <dt-bindings/interrupt-controller/irq.h>
+    #include <dt-bindings/interrupt-controller/arm-gic.h>
+
+    sdhc: mmc@8e00 {
+      compatible = "amlogic,meson8-sdhc", "amlogic,meson-mx-sdhc";
+      reg = <0x8e00 0x42>;
+      interrupts = <GIC_SPI 78 IRQ_TYPE_EDGE_RISING>;
+      clocks = <&xtal>,
+               <&fclk_div4>,
+               <&fclk_div3>,
+               <&fclk_div5>,
+               <&sdhc_pclk>;
+      clock-names = "clkin0", "clkin1", "clkin2", "clkin3", "pclk";
+    };
diff --git a/Documentation/devicetree/bindings/mmc/arasan,sdhci.txt b/Documentation/devicetree/bindings/mmc/arasan,sdhci.txt
index 428685eb2ded..f29bf7dd2ece 100644
--- a/Documentation/devicetree/bindings/mmc/arasan,sdhci.txt
+++ b/Documentation/devicetree/bindings/mmc/arasan,sdhci.txt
@@ -18,12 +18,21 @@ Required Properties:
     - "xlnx,zynqmp-8.9a": ZynqMP SDHCI 8.9a PHY
       For this device it is strongly suggested to include clock-output-names and
       #clock-cells.
+    - "xlnx,versal-8.9a": Versal SDHCI 8.9a PHY
+      For this device it is strongly suggested to include clock-output-names and
+      #clock-cells.
     - "ti,am654-sdhci-5.1", "arasan,sdhci-5.1": TI AM654 MMC PHY
 	Note: This binding has been deprecated and moved to [5].
     - "intel,lgm-sdhci-5.1-emmc", "arasan,sdhci-5.1": Intel LGM eMMC PHY
       For this device it is strongly suggested to include arasan,soc-ctl-syscon.
     - "intel,lgm-sdhci-5.1-sdxc", "arasan,sdhci-5.1": Intel LGM SDXC PHY
       For this device it is strongly suggested to include arasan,soc-ctl-syscon.
+    - "intel,keembay-sdhci-5.1-emmc", "arasan,sdhci-5.1": Intel Keem Bay eMMC
+      For this device it is strongly suggested to include arasan,soc-ctl-syscon.
+    - "intel,keembay-sdhci-5.1-sd": Intel Keem Bay SD controller
+      For this device it is strongly suggested to include arasan,soc-ctl-syscon.
+    - "intel,keembay-sdhci-5.1-sdio": Intel Keem Bay SDIO controller
+      For this device it is strongly suggested to include arasan,soc-ctl-syscon.
 
   [5] Documentation/devicetree/bindings/mmc/sdhci-am654.txt
 
@@ -104,6 +113,18 @@ Example:
 		clk-phase-sd-hs = <63>, <72>;
 	};
 
+	sdhci: mmc@f1040000 {
+		compatible = "xlnx,versal-8.9a", "arasan,sdhci-8.9a";
+		interrupt-parent = <&gic>;
+		interrupts = <0 126 4>;
+		reg = <0x0 0xf1040000 0x0 0x10000>;
+		clocks = <&clk200>, <&clk200>;
+		clock-names = "clk_xin", "clk_ahb";
+		clock-output-names = "clk_out_sd0", "clk_in_sd0";
+		#clock-cells = <1>;
+		clk-phase-sd-hs = <132>, <60>;
+	};
+
 	emmc: sdhci@ec700000 {
 		compatible = "intel,lgm-sdhci-5.1-emmc", "arasan,sdhci-5.1";
 		reg = <0xec700000 0x300>;
@@ -133,3 +154,39 @@ Example:
 		phy-names = "phy_arasan";
 		arasan,soc-ctl-syscon = <&sysconf>;
 	};
+
+	mmc: mmc@33000000 {
+		compatible = "intel,keembay-sdhci-5.1-emmc", "arasan,sdhci-5.1";
+		interrupts = <GIC_SPI 82 IRQ_TYPE_LEVEL_HIGH>;
+		reg = <0x0 0x33000000 0x0 0x300>;
+		clock-names = "clk_xin", "clk_ahb";
+		clocks = <&scmi_clk KEEM_BAY_PSS_AUX_EMMC>,
+			 <&scmi_clk KEEM_BAY_PSS_EMMC>;
+		phys = <&emmc_phy>;
+		phy-names = "phy_arasan";
+		assigned-clocks = <&scmi_clk KEEM_BAY_PSS_AUX_EMMC>;
+		assigned-clock-rates = <200000000>;
+		clock-output-names = "emmc_cardclock";
+		#clock-cells = <0>;
+		arasan,soc-ctl-syscon = <&mmc_phy_syscon>;
+	};
+
+	sd0: mmc@31000000 {
+		compatible = "intel,keembay-sdhci-5.1-sd";
+		interrupts = <GIC_SPI 83 IRQ_TYPE_LEVEL_HIGH>;
+		reg = <0x0 0x31000000 0x0 0x300>;
+		clock-names = "clk_xin", "clk_ahb";
+		clocks = <&scmi_clk KEEM_BAY_PSS_AUX_SD0>,
+			 <&scmi_clk KEEM_BAY_PSS_SD0>;
+		arasan,soc-ctl-syscon = <&sd0_phy_syscon>;
+	};
+
+	sd1: mmc@32000000 {
+		compatible = "intel,keembay-sdhci-5.1-sdio";
+		interrupts = <GIC_SPI 84 IRQ_TYPE_LEVEL_HIGH>;
+		reg = <0x0 0x32000000 0x0 0x300>;
+		clock-names = "clk_xin", "clk_ahb";
+		clocks = <&scmi_clk KEEM_BAY_PSS_AUX_SD1>,
+			 <&scmi_clk KEEM_BAY_PSS_SD1>;
+		arasan,soc-ctl-syscon = <&sd1_phy_syscon>;
+	};
diff --git a/Documentation/devicetree/bindings/mmc/renesas,mmcif.txt b/Documentation/devicetree/bindings/mmc/renesas,mmcif.txt
index c064af5838aa..291532ac0446 100644
--- a/Documentation/devicetree/bindings/mmc/renesas,mmcif.txt
+++ b/Documentation/devicetree/bindings/mmc/renesas,mmcif.txt
@@ -11,6 +11,7 @@ Required properties:
 	- "renesas,mmcif-r7s72100" for the MMCIF found in r7s72100 SoCs
 	- "renesas,mmcif-r8a73a4" for the MMCIF found in r8a73a4 SoCs
 	- "renesas,mmcif-r8a7740" for the MMCIF found in r8a7740 SoCs
+	- "renesas,mmcif-r8a7742" for the MMCIF found in r8a7742 SoCs
 	- "renesas,mmcif-r8a7743" for the MMCIF found in r8a7743 SoCs
 	- "renesas,mmcif-r8a7744" for the MMCIF found in r8a7744 SoCs
 	- "renesas,mmcif-r8a7745" for the MMCIF found in r8a7745 SoCs
@@ -24,8 +25,8 @@ Required properties:
 - interrupts: Some SoCs have only 1 shared interrupt, while others have either
   2 or 3 individual interrupts (error, int, card detect). Below is the number
   of interrupts for each SoC:
-    1: r8a73a4, r8a7743, r8a7744, r8a7745, r8a7778, r8a7790, r8a7791, r8a7793,
-       r8a7794
+    1: r8a73a4, r8a7742, r8a7743, r8a7744, r8a7745, r8a7778, r8a7790, r8a7791,
+       r8a7793, r8a7794
     2: r8a7740, sh73a0
     3: r7s72100
 
diff --git a/Documentation/devicetree/bindings/mmc/renesas,sdhi.txt b/Documentation/devicetree/bindings/mmc/renesas,sdhi.txt
index e6cc47844207..0ca9a622cce0 100644
--- a/Documentation/devicetree/bindings/mmc/renesas,sdhi.txt
+++ b/Documentation/devicetree/bindings/mmc/renesas,sdhi.txt
@@ -7,6 +7,7 @@ Required properties:
 		"renesas,sdhi-r7s9210" - SDHI IP on R7S9210 SoC
 		"renesas,sdhi-r8a73a4" - SDHI IP on R8A73A4 SoC
 		"renesas,sdhi-r8a7740" - SDHI IP on R8A7740 SoC
+		"renesas,sdhi-r8a7742" - SDHI IP on R8A7742 SoC
 		"renesas,sdhi-r8a7743" - SDHI IP on R8A7743 SoC
 		"renesas,sdhi-r8a7744" - SDHI IP on R8A7744 SoC
 		"renesas,sdhi-r8a7745" - SDHI IP on R8A7745 SoC
diff --git a/Documentation/devicetree/bindings/mmc/sdhci-msm.txt b/Documentation/devicetree/bindings/mmc/sdhci-msm.txt
index 5445931c5ab9..b8e1d2b7aea9 100644
--- a/Documentation/devicetree/bindings/mmc/sdhci-msm.txt
+++ b/Documentation/devicetree/bindings/mmc/sdhci-msm.txt
@@ -17,6 +17,7 @@ Required properties:
 		"qcom,msm8916-sdhci", "qcom,sdhci-msm-v4"
 		"qcom,msm8992-sdhci", "qcom,sdhci-msm-v4"
 		"qcom,msm8996-sdhci", "qcom,sdhci-msm-v4"
+		"qcom,sm8250-sdhci", "qcom,sdhci-msm-v5"
 		"qcom,sdm845-sdhci", "qcom,sdhci-msm-v5"
 		"qcom,qcs404-sdhci", "qcom,sdhci-msm-v5"
 		"qcom,sc7180-sdhci", "qcom,sdhci-msm-v5";
@@ -46,6 +47,13 @@ Required properties:
 	"cal"	- reference clock for RCLK delay calibration (optional)
 	"sleep"	- sleep clock for RCLK delay calibration (optional)
 
+- qcom,ddr-config: Certain chipsets and platforms require particular settings
+	for the DDR_CONFIG register. Use this field to specify the register
+	value as per the Hardware Programming Guide.
+
+- qcom,dll-config: Chipset and Platform specific value. Use this field to
+	specify the DLL_CONFIG register value as per Hardware Programming Guide.
+
 Example:
 
 	sdhc_1: sdhci@f9824900 {
@@ -63,6 +71,9 @@ Example:
 
 		clocks = <&gcc GCC_SDCC1_APPS_CLK>, <&gcc GCC_SDCC1_AHB_CLK>;
 		clock-names = "core", "iface";
+
+		qcom,dll-config = <0x000f642c>;
+		qcom,ddr-config = <0x80040868>;
 	};
 
 	sdhc_2: sdhci@f98a4900 {
@@ -80,4 +91,7 @@ Example:
 
 		clocks = <&gcc GCC_SDCC2_APPS_CLK>, <&gcc GCC_SDCC2_AHB_CLK>;
 		clock-names = "core", "iface";
+
+		qcom,dll-config = <0x0007642c>;
+		qcom,ddr-config = <0x80040868>;
 	};
diff --git a/Documentation/devicetree/bindings/mmc/sdhci-pxa.txt b/Documentation/devicetree/bindings/mmc/sdhci-pxa.txt
deleted file mode 100644
index 3d1b449d6097..000000000000
--- a/Documentation/devicetree/bindings/mmc/sdhci-pxa.txt
+++ /dev/null
@@ -1,50 +0,0 @@
-* Marvell sdhci-pxa v2/v3 controller
-
-This file documents differences between the core properties in mmc.txt
-and the properties used by the sdhci-pxav2 and sdhci-pxav3 drivers.
-
-Required properties:
-- compatible: Should be "mrvl,pxav2-mmc", "mrvl,pxav3-mmc" or
-  "marvell,armada-380-sdhci".
-- reg:
-  * for "mrvl,pxav2-mmc" and "mrvl,pxav3-mmc", one register area for
-    the SDHCI registers.
-
-  * for "marvell,armada-380-sdhci", three register areas. The first
-    one for the SDHCI registers themselves, the second one for the
-    AXI/Mbus bridge registers of the SDHCI unit, the third one for the
-    SDIO3 Configuration register
-- reg names: should be "sdhci", "mbus", "conf-sdio3". only mandatory
-  for "marvell,armada-380-sdhci"
-- clocks: Array of clocks required for SDHCI; requires at least one for
-    I/O clock.
-- clock-names: Array of names corresponding to clocks property; shall be
-    "io" for I/O clock and "core" for optional core clock.
-
-Optional properties:
-- mrvl,clk-delay-cycles: Specify a number of cycles to delay for tuning.
-
-Example:
-
-sdhci@d4280800 {
-	compatible = "mrvl,pxav3-mmc";
-	reg = <0xd4280800 0x800>;
-	bus-width = <8>;
-	interrupts = <27>;
-	clocks = <&chip CLKID_SDIO1XIN>, <&chip CLKID_SDIO1>;
-	clock-names = "io", "core";
-	non-removable;
-	mrvl,clk-delay-cycles = <31>;
-};
-
-sdhci@d8000 {
-	compatible = "marvell,armada-380-sdhci";
-	reg-names = "sdhci", "mbus", "conf-sdio3";
-	reg = <0xd8000 0x1000>,
-		<0xdc000 0x100>;
-		<0x18454 0x4>;
-	interrupts = <0 25 0x4>;
-	clocks = <&gateclk 17>;
-	clock-names = "io";
-	mrvl,clk-delay-cycles = <0x1F>;
-};
diff --git a/Documentation/devicetree/bindings/mmc/sdhci-pxa.yaml b/Documentation/devicetree/bindings/mmc/sdhci-pxa.yaml
new file mode 100644
index 000000000000..a58715c860b7
--- /dev/null
+++ b/Documentation/devicetree/bindings/mmc/sdhci-pxa.yaml
@@ -0,0 +1,102 @@
+# SPDX-License-Identifier: GPL-2.0-only
+%YAML 1.2
+---
+$id: http://devicetree.org/schemas/mmc/sdhci-pxa.yaml#
+$schema: http://devicetree.org/meta-schemas/core.yaml#
+
+title: Marvell PXA SDHCI v2/v3 bindings
+
+maintainers:
+  - Ulf Hansson <ulf.hansson@linaro.org>
+
+allOf:
+  - $ref: mmc-controller.yaml#
+  - if:
+      properties:
+        compatible:
+          contains:
+            const: marvell,armada-380-sdhci
+    then:
+      properties:
+        regs:
+          minItems: 3
+        reg-names:
+          minItems: 3
+      required:
+        - reg-names
+    else:
+      properties:
+        regs:
+          maxItems: 1
+        reg-names:
+          maxItems: 1
+
+properties:
+  compatible:
+    enum:
+      - mrvl,pxav2-mmc
+      - mrvl,pxav3-mmc
+      - marvell,armada-380-sdhci
+
+  reg:
+    minItems: 1
+    maxItems: 3
+
+  reg-names:
+    items:
+      - const: sdhci
+      - const: mbus
+      - const: conf-sdio3
+
+  interrupts:
+    maxItems: 1
+
+  clocks:
+    minItems: 1
+    maxItems: 2
+
+  clock-names:
+    minItems: 1
+    maxItems: 2
+    items:
+      - const: io
+      - const: core
+
+  mrvl,clk-delay-cycles:
+    description: Specify a number of cycles to delay for tuning.
+    $ref: /schemas/types.yaml#/definitions/uint32
+
+required:
+  - compatible
+  - reg
+  - interrupts
+  - clocks
+  - clock-names
+
+examples:
+  - |
+    #include <dt-bindings/clock/berlin2.h>
+    mmc@d4280800 {
+        compatible = "mrvl,pxav3-mmc";
+        reg = <0xd4280800 0x800>;
+        bus-width = <8>;
+        interrupts = <27>;
+        clocks = <&chip CLKID_SDIO1XIN>, <&chip CLKID_SDIO1>;
+        clock-names = "io", "core";
+        non-removable;
+        mrvl,clk-delay-cycles = <31>;
+    };
+  - |
+    mmc@d8000 {
+        compatible = "marvell,armada-380-sdhci";
+        reg-names = "sdhci", "mbus", "conf-sdio3";
+        reg = <0xd8000 0x1000>,
+              <0xdc000 0x100>,
+              <0x18454 0x4>;
+        interrupts = <0 25 0x4>;
+        clocks = <&gateclk 17>;
+        clock-names = "io";
+        mrvl,clk-delay-cycles = <0x1F>;
+    };
+
+...