media: i2c: Drop unused s5k6aa camera sensor driver

The s5k6aa camera sensor driver doesn't support DT and relies on
platform data. The last board files supplying platform data for that
device have been removed from the kernel in v3.11. The driver hasn't
been used since them. Drop it.

Signed-off-by: Laurent Pinchart <laurent.pinchart@ideasonboard.com>
Acked-by: Sakari Ailus <sakari.ailus@linux.intel.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@kernel.org>

5 files changed, 0 insertions, 1711 deletions

diff --git a/Documentation/admin-guide/media/i2c-cardlist.rst b/Documentation/admin-guide/media/i2c-cardlist.rst
index e6c2ae43d02d..b9a3a561183f 100644
--- a/Documentation/admin-guide/media/i2c-cardlist.rst
+++ b/Documentation/admin-guide/media/i2c-cardlist.rst
@@ -105,7 +105,6 @@ s5c73m3       Samsung S5C73M3 sensor
 s5k4ecgx      Samsung S5K4ECGX sensor
 s5k5baf       Samsung S5K5BAF sensor
 s5k6a3        Samsung S5K6A3 sensor
-s5k6aa        Samsung S5K6AAFX sensor
 sr030pc30     Siliconfile SR030PC30 sensor
 vs6624        ST VS6624 sensor
 ============  ==========================================================
diff --git a/drivers/media/i2c/Kconfig b/drivers/media/i2c/Kconfig
index 40304e017458..a7f2a8ba2fd3 100644
--- a/drivers/media/i2c/Kconfig
+++ b/drivers/media/i2c/Kconfig
@@ -784,15 +784,6 @@ config VIDEO_S5K6A3
 	  This is a V4L2 sensor driver for Samsung S5K6A3 raw
 	  camera sensor.
 
-config VIDEO_S5K6AA
-	tristate "Samsung S5K6AAFX sensor support"
-	depends on I2C && VIDEO_DEV
-	select MEDIA_CONTROLLER
-	select VIDEO_V4L2_SUBDEV_API
-	help
-	  This is a V4L2 sensor driver for Samsung S5K6AA(FX) 1.3M
-	  camera sensor with an embedded SoC image signal processor.
-
 config VIDEO_SR030PC30
 	tristate "Siliconfile SR030PC30 sensor support"
 	depends on I2C && VIDEO_DEV
diff --git a/drivers/media/i2c/Makefile b/drivers/media/i2c/Makefile
index e5e06c56efcd..6bc6c4682132 100644
--- a/drivers/media/i2c/Makefile
+++ b/drivers/media/i2c/Makefile
@@ -105,7 +105,6 @@ obj-$(CONFIG_VIDEO_RJ54N1) += rj54n1cb0c.o
 obj-$(CONFIG_VIDEO_S5C73M3) += s5c73m3/
 obj-$(CONFIG_VIDEO_S5K5BAF) += s5k5baf.o
 obj-$(CONFIG_VIDEO_S5K6A3) += s5k6a3.o
-obj-$(CONFIG_VIDEO_S5K6AA) += s5k6aa.o
 obj-$(CONFIG_VIDEO_SAA6588) += saa6588.o
 obj-$(CONFIG_VIDEO_SAA6752HS) += saa6752hs.o
 obj-$(CONFIG_VIDEO_SAA7110) += saa7110.o
diff --git a/drivers/media/i2c/s5k6aa.c b/drivers/media/i2c/s5k6aa.c
deleted file mode 100644
index 5996153371fc..000000000000
--- a/drivers/media/i2c/s5k6aa.c
+++ /dev/null
@@ -1,1652 +0,0 @@
-// SPDX-License-Identifier: GPL-2.0-or-later
-/*
- * Driver for Samsung S5K6AAFX SXGA 1/6" 1.3M CMOS Image Sensor
- * with embedded SoC ISP.
- *
- * Copyright (C) 2011, Samsung Electronics Co., Ltd.
- * Sylwester Nawrocki <s.nawrocki@samsung.com>
- *
- * Based on a driver authored by Dongsoo Nathaniel Kim.
- * Copyright (C) 2009, Dongsoo Nathaniel Kim <dongsoo45.kim@samsung.com>
- */
-
-#include <linux/clk.h>
-#include <linux/delay.h>
-#include <linux/gpio.h>
-#include <linux/i2c.h>
-#include <linux/media.h>
-#include <linux/module.h>
-#include <linux/regulator/consumer.h>
-#include <linux/slab.h>
-
-#include <media/media-entity.h>
-#include <media/v4l2-ctrls.h>
-#include <media/v4l2-device.h>
-#include <media/v4l2-subdev.h>
-#include <media/v4l2-mediabus.h>
-#include <media/i2c/s5k6aa.h>
-
-static int debug;
-module_param(debug, int, 0644);
-
-#define DRIVER_NAME			"S5K6AA"
-
-/* The token to indicate array termination */
-#define S5K6AA_TERM			0xffff
-#define S5K6AA_OUT_WIDTH_DEF		640
-#define S5K6AA_OUT_HEIGHT_DEF		480
-#define S5K6AA_WIN_WIDTH_MAX		1280
-#define S5K6AA_WIN_HEIGHT_MAX		1024
-#define S5K6AA_WIN_WIDTH_MIN		8
-#define S5K6AA_WIN_HEIGHT_MIN		8
-
-/*
- * H/W register Interface (0xD0000000 - 0xD0000FFF)
- */
-#define AHB_MSB_ADDR_PTR		0xfcfc
-#define GEN_REG_OFFSH			0xd000
-#define REG_CMDWR_ADDRH			0x0028
-#define REG_CMDWR_ADDRL			0x002a
-#define REG_CMDRD_ADDRH			0x002c
-#define REG_CMDRD_ADDRL			0x002e
-#define REG_CMDBUF0_ADDR		0x0f12
-#define REG_CMDBUF1_ADDR		0x0f10
-
-/*
- * Host S/W Register interface (0x70000000 - 0x70002000)
- * The value of the two most significant address bytes is 0x7000,
- * (HOST_SWIF_OFFS_H). The register addresses below specify 2 LSBs.
- */
-#define HOST_SWIF_OFFSH			0x7000
-
-/* Initialization parameters */
-/* Master clock frequency in KHz */
-#define REG_I_INCLK_FREQ_L		0x01b8
-#define REG_I_INCLK_FREQ_H		0x01ba
-#define  MIN_MCLK_FREQ_KHZ		6000U
-#define  MAX_MCLK_FREQ_KHZ		27000U
-#define REG_I_USE_NPVI_CLOCKS		0x01c6
-#define REG_I_USE_NMIPI_CLOCKS		0x01c8
-
-/* Clock configurations, n = 0..2. REG_I_* frequency unit is 4 kHz. */
-#define REG_I_OPCLK_4KHZ(n)		((n) * 6 + 0x01cc)
-#define REG_I_MIN_OUTRATE_4KHZ(n)	((n) * 6 + 0x01ce)
-#define REG_I_MAX_OUTRATE_4KHZ(n)	((n) * 6 + 0x01d0)
-#define  SYS_PLL_OUT_FREQ		(48000000 / 4000)
-#define  PCLK_FREQ_MIN			(24000000 / 4000)
-#define  PCLK_FREQ_MAX			(48000000 / 4000)
-#define REG_I_INIT_PARAMS_UPDATED	0x01e0
-#define REG_I_ERROR_INFO		0x01e2
-
-/* General purpose parameters */
-#define REG_USER_BRIGHTNESS		0x01e4
-#define REG_USER_CONTRAST		0x01e6
-#define REG_USER_SATURATION		0x01e8
-#define REG_USER_SHARPBLUR		0x01ea
-
-#define REG_G_SPEC_EFFECTS		0x01ee
-#define REG_G_ENABLE_PREV		0x01f0
-#define REG_G_ENABLE_PREV_CHG		0x01f2
-#define REG_G_NEW_CFG_SYNC		0x01f8
-#define REG_G_PREVZOOM_IN_WIDTH		0x020a
-#define REG_G_PREVZOOM_IN_HEIGHT	0x020c
-#define REG_G_PREVZOOM_IN_XOFFS		0x020e
-#define REG_G_PREVZOOM_IN_YOFFS		0x0210
-#define REG_G_INPUTS_CHANGE_REQ		0x021a
-#define REG_G_ACTIVE_PREV_CFG		0x021c
-#define REG_G_PREV_CFG_CHG		0x021e
-#define REG_G_PREV_OPEN_AFTER_CH	0x0220
-#define REG_G_PREV_CFG_ERROR		0x0222
-
-/* Preview control section. n = 0...4. */
-#define PREG(n, x)			((n) * 0x26 + x)
-#define REG_P_OUT_WIDTH(n)		PREG(n, 0x0242)
-#define REG_P_OUT_HEIGHT(n)		PREG(n, 0x0244)
-#define REG_P_FMT(n)			PREG(n, 0x0246)
-#define REG_P_MAX_OUT_RATE(n)		PREG(n, 0x0248)
-#define REG_P_MIN_OUT_RATE(n)		PREG(n, 0x024a)
-#define REG_P_PVI_MASK(n)		PREG(n, 0x024c)
-#define REG_P_CLK_INDEX(n)		PREG(n, 0x024e)
-#define REG_P_FR_RATE_TYPE(n)		PREG(n, 0x0250)
-#define  FR_RATE_DYNAMIC		0
-#define  FR_RATE_FIXED			1
-#define  FR_RATE_FIXED_ACCURATE		2
-#define REG_P_FR_RATE_Q_TYPE(n)		PREG(n, 0x0252)
-#define  FR_RATE_Q_BEST_FRRATE		1 /* Binning enabled */
-#define  FR_RATE_Q_BEST_QUALITY		2 /* Binning disabled */
-/* Frame period in 0.1 ms units */
-#define REG_P_MAX_FR_TIME(n)		PREG(n, 0x0254)
-#define REG_P_MIN_FR_TIME(n)		PREG(n, 0x0256)
-/* Conversion to REG_P_[MAX/MIN]_FR_TIME value; __t: time in us */
-#define  US_TO_FR_TIME(__t)		((__t) / 100)
-#define  S5K6AA_MIN_FR_TIME		33300  /* us */
-#define  S5K6AA_MAX_FR_TIME		650000 /* us */
-#define  S5K6AA_MAX_HIGHRES_FR_TIME	666    /* x100 us */
-/* The below 5 registers are for "device correction" values */
-#define REG_P_COLORTEMP(n)		PREG(n, 0x025e)
-#define REG_P_PREV_MIRROR(n)		PREG(n, 0x0262)
-
-/* Extended image property controls */
-/* Exposure time in 10 us units */
-#define REG_SF_USR_EXPOSURE_L		0x03c6
-#define REG_SF_USR_EXPOSURE_H		0x03c8
-#define REG_SF_USR_EXPOSURE_CHG		0x03ca
-#define REG_SF_USR_TOT_GAIN		0x03cc
-#define REG_SF_USR_TOT_GAIN_CHG		0x03ce
-#define REG_SF_RGAIN			0x03d0
-#define REG_SF_RGAIN_CHG		0x03d2
-#define REG_SF_GGAIN			0x03d4
-#define REG_SF_GGAIN_CHG		0x03d6
-#define REG_SF_BGAIN			0x03d8
-#define REG_SF_BGAIN_CHG		0x03da
-#define REG_SF_FLICKER_QUANT		0x03dc
-#define REG_SF_FLICKER_QUANT_CHG	0x03de
-
-/* Output interface (parallel/MIPI) setup */
-#define REG_OIF_EN_MIPI_LANES		0x03fa
-#define REG_OIF_EN_PACKETS		0x03fc
-#define REG_OIF_CFG_CHG			0x03fe
-
-/* Auto-algorithms enable mask */
-#define REG_DBG_AUTOALG_EN		0x0400
-#define  AALG_ALL_EN_MASK		(1 << 0)
-#define  AALG_AE_EN_MASK		(1 << 1)
-#define  AALG_DIVLEI_EN_MASK		(1 << 2)
-#define  AALG_WB_EN_MASK		(1 << 3)
-#define  AALG_FLICKER_EN_MASK		(1 << 5)
-#define  AALG_FIT_EN_MASK		(1 << 6)
-#define  AALG_WRHW_EN_MASK		(1 << 7)
-
-/* Firmware revision information */
-#define REG_FW_APIVER			0x012e
-#define  S5K6AAFX_FW_APIVER		0x0001
-#define REG_FW_REVISION			0x0130
-
-/* For now we use only one user configuration register set */
-#define S5K6AA_MAX_PRESETS		1
-
-static const char * const s5k6aa_supply_names[] = {
-	"vdd_core",	/* Digital core supply 1.5V (1.4V to 1.6V) */
-	"vdda",		/* Analog power supply 2.8V (2.6V to 3.0V) */
-	"vdd_reg",	/* Regulator input power 1.8V (1.7V to 1.9V)
-			   or 2.8V (2.6V to 3.0) */
-	"vddio",	/* I/O supply 1.8V (1.65V to 1.95V)
-			   or 2.8V (2.5V to 3.1V) */
-};
-#define S5K6AA_NUM_SUPPLIES ARRAY_SIZE(s5k6aa_supply_names)
-
-enum s5k6aa_gpio_id {
-	STBY,
-	RSET,
-	GPIO_NUM,
-};
-
-struct s5k6aa_regval {
-	u16 addr;
-	u16 val;
-};
-
-struct s5k6aa_pixfmt {
-	u32 code;
-	u32 colorspace;
-	/* REG_P_FMT(x) register value */
-	u16 reg_p_fmt;
-};
-
-struct s5k6aa_preset {
-	/* output pixel format and resolution */
-	struct v4l2_mbus_framefmt mbus_fmt;
-	u8 clk_id;
-	u8 index;
-};
-
-struct s5k6aa_ctrls {
-	struct v4l2_ctrl_handler handler;
-	/* Auto / manual white balance cluster */
-	struct v4l2_ctrl *awb;
-	struct v4l2_ctrl *gain_red;
-	struct v4l2_ctrl *gain_blue;
-	struct v4l2_ctrl *gain_green;
-	/* Mirror cluster */
-	struct v4l2_ctrl *hflip;
-	struct v4l2_ctrl *vflip;
-	/* Auto exposure / manual exposure and gain cluster */
-	struct v4l2_ctrl *auto_exp;
-	struct v4l2_ctrl *exposure;
-	struct v4l2_ctrl *gain;
-};
-
-struct s5k6aa_interval {
-	u16 reg_fr_time;
-	struct v4l2_fract interval;
-	/* Maximum rectangle for the interval */
-	struct v4l2_frmsize_discrete size;
-};
-
-struct s5k6aa {
-	struct v4l2_subdev sd;
-	struct media_pad pad;
-
-	enum v4l2_mbus_type bus_type;
-	u8 mipi_lanes;
-
-	int (*s_power)(int enable);
-	struct regulator_bulk_data supplies[S5K6AA_NUM_SUPPLIES];
-	struct s5k6aa_gpio gpio[GPIO_NUM];
-
-	/* external master clock frequency */
-	unsigned long mclk_frequency;
-	/* ISP internal master clock frequency */
-	u16 clk_fop;
-	/* output pixel clock frequency range */
-	u16 pclk_fmin;
-	u16 pclk_fmax;
-
-	unsigned int inv_hflip:1;
-	unsigned int inv_vflip:1;
-
-	/* protects the struct members below */
-	struct mutex lock;
-
-	/* sensor matrix scan window */
-	struct v4l2_rect ccd_rect;
-
-	struct s5k6aa_ctrls ctrls;
-	struct s5k6aa_preset presets[S5K6AA_MAX_PRESETS];
-	struct s5k6aa_preset *preset;
-	const struct s5k6aa_interval *fiv;
-
-	unsigned int streaming:1;
-	unsigned int apply_cfg:1;
-	unsigned int apply_crop:1;
-	unsigned int power;
-};
-
-static struct s5k6aa_regval s5k6aa_analog_config[] = {
-	/* Analog settings */
-	{ 0x112a, 0x0000 }, { 0x1132, 0x0000 },
-	{ 0x113e, 0x0000 }, { 0x115c, 0x0000 },
-	{ 0x1164, 0x0000 }, { 0x1174, 0x0000 },
-	{ 0x1178, 0x0000 }, { 0x077a, 0x0000 },
-	{ 0x077c, 0x0000 }, { 0x077e, 0x0000 },
-	{ 0x0780, 0x0000 }, { 0x0782, 0x0000 },
-	{ 0x0784, 0x0000 }, { 0x0786, 0x0000 },
-	{ 0x0788, 0x0000 }, { 0x07a2, 0x0000 },
-	{ 0x07a4, 0x0000 }, { 0x07a6, 0x0000 },
-	{ 0x07a8, 0x0000 }, { 0x07b6, 0x0000 },
-	{ 0x07b8, 0x0002 }, { 0x07ba, 0x0004 },
-	{ 0x07bc, 0x0004 }, { 0x07be, 0x0005 },
-	{ 0x07c0, 0x0005 }, { S5K6AA_TERM, 0 },
-};
-
-/* TODO: Add RGB888 and Bayer format */
-static const struct s5k6aa_pixfmt s5k6aa_formats[] = {
-	{ MEDIA_BUS_FMT_YUYV8_2X8,	V4L2_COLORSPACE_JPEG,	5 },
-	/* range 16-240 */
-	{ MEDIA_BUS_FMT_YUYV8_2X8,	V4L2_COLORSPACE_REC709,	6 },
-	{ MEDIA_BUS_FMT_RGB565_2X8_BE,	V4L2_COLORSPACE_JPEG,	0 },
-};
-
-static const struct s5k6aa_interval s5k6aa_intervals[] = {
-	{ 1000, {10000, 1000000}, {1280, 1024} }, /* 10 fps */
-	{ 666,  {15000, 1000000}, {1280, 1024} }, /* 15 fps */
-	{ 500,  {20000, 1000000}, {1280, 720} },  /* 20 fps */
-	{ 400,  {25000, 1000000}, {640, 480} },   /* 25 fps */
-	{ 333,  {33300, 1000000}, {640, 480} },   /* 30 fps */
-};
-
-#define S5K6AA_INTERVAL_DEF_INDEX 1 /* 15 fps */
-
-static inline struct v4l2_subdev *ctrl_to_sd(struct v4l2_ctrl *ctrl)
-{
-	return &container_of(ctrl->handler, struct s5k6aa, ctrls.handler)->sd;
-}
-
-static inline struct s5k6aa *to_s5k6aa(struct v4l2_subdev *sd)
-{
-	return container_of(sd, struct s5k6aa, sd);
-}
-
-/* Set initial values for all preview presets */
-static void s5k6aa_presets_data_init(struct s5k6aa *s5k6aa)
-{
-	struct s5k6aa_preset *preset = &s5k6aa->presets[0];
-	int i;
-
-	for (i = 0; i < S5K6AA_MAX_PRESETS; i++) {
-		preset->mbus_fmt.width	= S5K6AA_OUT_WIDTH_DEF;
-		preset->mbus_fmt.height	= S5K6AA_OUT_HEIGHT_DEF;
-		preset->mbus_fmt.code	= s5k6aa_formats[0].code;
-		preset->index		= i;
-		preset->clk_id		= 0;
-		preset++;
-	}
-
-	s5k6aa->fiv = &s5k6aa_intervals[S5K6AA_INTERVAL_DEF_INDEX];
-	s5k6aa->preset = &s5k6aa->presets[0];
-}
-
-static int s5k6aa_i2c_read(struct i2c_client *client, u16 addr, u16 *val)
-{
-	u8 wbuf[2] = {addr >> 8, addr & 0xFF};
-	struct i2c_msg msg[2];
-	u8 rbuf[2];
-	int ret;
-
-	msg[0].addr = client->addr;
-	msg[0].flags = 0;
-	msg[0].len = 2;
-	msg[0].buf = wbuf;
-
-	msg[1].addr = client->addr;
-	msg[1].flags = I2C_M_RD;
-	msg[1].len = 2;
-	msg[1].buf = rbuf;
-
-	ret = i2c_transfer(client->adapter, msg, 2);
-	*val = be16_to_cpu(*((__be16 *)rbuf));
-
-	v4l2_dbg(3, debug, client, "i2c_read: 0x%04X : 0x%04x\n", addr, *val);
-
-	return ret == 2 ? 0 : ret;
-}
-
-static int s5k6aa_i2c_write(struct i2c_client *client, u16 addr, u16 val)
-{
-	u8 buf[4] = {addr >> 8, addr & 0xFF, val >> 8, val & 0xFF};
-
-	int ret = i2c_master_send(client, buf, 4);
-	v4l2_dbg(3, debug, client, "i2c_write: 0x%04X : 0x%04x\n", addr, val);
-
-	return ret == 4 ? 0 : ret;
-}
-
-/* The command register write, assumes Command_Wr_addH = 0x7000. */
-static int s5k6aa_write(struct i2c_client *c, u16 addr, u16 val)
-{
-	int ret = s5k6aa_i2c_write(c, REG_CMDWR_ADDRL, addr);
-	if (ret)
-		return ret;
-	return s5k6aa_i2c_write(c, REG_CMDBUF0_ADDR, val);
-}
-
-/* The command register read, assumes Command_Rd_addH = 0x7000. */
-static int s5k6aa_read(struct i2c_client *client, u16 addr, u16 *val)
-{
-	int ret = s5k6aa_i2c_write(client, REG_CMDRD_ADDRL, addr);
-	if (ret)
-		return ret;
-	return s5k6aa_i2c_read(client, REG_CMDBUF0_ADDR, val);
-}
-
-static int s5k6aa_write_array(struct v4l2_subdev *sd,
-			      const struct s5k6aa_regval *msg)
-{
-	struct i2c_client *client = v4l2_get_subdevdata(sd);
-	u16 addr_incr = 0;
-	int ret = 0;
-
-	while (msg->addr != S5K6AA_TERM) {
-		if (addr_incr != 2)
-			ret = s5k6aa_i2c_write(client, REG_CMDWR_ADDRL,
-					       msg->addr);
-		if (ret)
-			break;
-		ret = s5k6aa_i2c_write(client, REG_CMDBUF0_ADDR, msg->val);
-		if (ret)
-			break;
-		/* Assume that msg->addr is always less than 0xfffc */
-		addr_incr = (msg + 1)->addr - msg->addr;
-		msg++;
-	}
-
-	return ret;
-}
-
-/* Configure the AHB high address bytes for GTG registers access */
-static int s5k6aa_set_ahb_address(struct i2c_client *client)
-{
-	int ret = s5k6aa_i2c_write(client, AHB_MSB_ADDR_PTR, GEN_REG_OFFSH);
-	if (ret)
-		return ret;
-	ret = s5k6aa_i2c_write(client, REG_CMDRD_ADDRH, HOST_SWIF_OFFSH);
-	if (ret)
-		return ret;
-	return s5k6aa_i2c_write(client, REG_CMDWR_ADDRH, HOST_SWIF_OFFSH);
-}
-
-/**
- * s5k6aa_configure_pixel_clocks - apply ISP main clock/PLL configuration
- * @s5k6aa: pointer to &struct s5k6aa describing the device
- *
- * Configure the internal ISP PLL for the required output frequency.
- * Locking: called with s5k6aa.lock mutex held.
- */
-static int s5k6aa_configure_pixel_clocks(struct s5k6aa *s5k6aa)
-{
-	struct i2c_client *c = v4l2_get_subdevdata(&s5k6aa->sd);
-	unsigned long fmclk = s5k6aa->mclk_frequency / 1000;
-	u16 status;
-	int ret;
-
-	if (WARN(fmclk < MIN_MCLK_FREQ_KHZ || fmclk > MAX_MCLK_FREQ_KHZ,
-		 "Invalid clock frequency: %ld\n", fmclk))
-		return -EINVAL;
-
-	s5k6aa->pclk_fmin = PCLK_FREQ_MIN;
-	s5k6aa->pclk_fmax = PCLK_FREQ_MAX;
-	s5k6aa->clk_fop = SYS_PLL_OUT_FREQ;
-
-	/* External input clock frequency in kHz */
-	ret = s5k6aa_write(c, REG_I_INCLK_FREQ_H, fmclk >> 16);
-	if (!ret)
-		ret = s5k6aa_write(c, REG_I_INCLK_FREQ_L, fmclk & 0xFFFF);
-	if (!ret)
-		ret = s5k6aa_write(c, REG_I_USE_NPVI_CLOCKS, 1);
-	/* Internal PLL frequency */
-	if (!ret)
-		ret = s5k6aa_write(c, REG_I_OPCLK_4KHZ(0), s5k6aa->clk_fop);
-	if (!ret)
-		ret = s5k6aa_write(c, REG_I_MIN_OUTRATE_4KHZ(0),
-				   s5k6aa->pclk_fmin);
-	if (!ret)
-		ret = s5k6aa_write(c, REG_I_MAX_OUTRATE_4KHZ(0),
-				   s5k6aa->pclk_fmax);
-	if (!ret)
-		ret = s5k6aa_write(c, REG_I_INIT_PARAMS_UPDATED, 1);
-	if (!ret)
-		ret = s5k6aa_read(c, REG_I_ERROR_INFO, &status);
-
-	return ret ? ret : (status ? -EINVAL : 0);
-}
-
-/* Set horizontal and vertical image flipping */
-static int s5k6aa_set_mirror(struct s5k6aa *s5k6aa, int horiz_flip)
-{
-	struct i2c_client *client = v4l2_get_subdevdata(&s5k6aa->sd);
-	int index = s5k6aa->preset->index;
-
-	unsigned int vflip = s5k6aa->ctrls.vflip->val ^ s5k6aa->inv_vflip;
-	unsigned int flip = (horiz_flip ^ s5k6aa->inv_hflip) | (vflip << 1);
-
-	return s5k6aa_write(client, REG_P_PREV_MIRROR(index), flip);
-}
-
-/* Configure auto/manual white balance and R/G/B gains */
-static int s5k6aa_set_awb(struct s5k6aa *s5k6aa, int awb)
-{
-	struct i2c_client *c = v4l2_get_subdevdata(&s5k6aa->sd);
-	struct s5k6aa_ctrls *ctrls = &s5k6aa->ctrls;
-	u16 reg;
-
-	int ret = s5k6aa_read(c, REG_DBG_AUTOALG_EN, &reg);
-
-	if (!ret && !awb) {
-		ret = s5k6aa_write(c, REG_SF_RGAIN, ctrls->gain_red->val);
-		if (!ret)
-			ret = s5k6aa_write(c, REG_SF_RGAIN_CHG, 1);
-		if (ret)
-			return ret;
-
-		ret = s5k6aa_write(c, REG_SF_GGAIN, ctrls->gain_green->val);
-		if (!ret)
-			ret = s5k6aa_write(c, REG_SF_GGAIN_CHG, 1);
-		if (ret)
-			return ret;
-
-		ret = s5k6aa_write(c, REG_SF_BGAIN, ctrls->gain_blue->val);
-		if (!ret)
-			ret = s5k6aa_write(c, REG_SF_BGAIN_CHG, 1);
-	}
-	if (!ret) {
-		reg = awb ? reg | AALG_WB_EN_MASK : reg & ~AALG_WB_EN_MASK;
-		ret = s5k6aa_write(c, REG_DBG_AUTOALG_EN, reg);
-	}
-
-	return ret;
-}
-
-/* Program FW with exposure time, 'exposure' in us units */
-static int s5k6aa_set_user_exposure(struct i2c_client *client, int exposure)
-{
-	unsigned int time = exposure / 10;
-
-	int ret = s5k6aa_write(client, REG_SF_USR_EXPOSURE_L, time & 0xffff);
-	if (!ret)
-		ret = s5k6aa_write(client, REG_SF_USR_EXPOSURE_H, time >> 16);
-	if (ret)
-		return ret;
-	return s5k6aa_write(client, REG_SF_USR_EXPOSURE_CHG, 1);
-}
-
-static int s5k6aa_set_user_gain(struct i2c_client *client, int gain)
-{
-	int ret = s5k6aa_write(client, REG_SF_USR_TOT_GAIN, gain);
-	if (ret)
-		return ret;
-	return s5k6aa_write(client, REG_SF_USR_TOT_GAIN_CHG, 1);
-}
-
-/* Set auto/manual exposure and total gain */
-static int s5k6aa_set_auto_exposure(struct s5k6aa *s5k6aa, int value)
-{
-	struct i2c_client *c = v4l2_get_subdevdata(&s5k6aa->sd);
-	unsigned int exp_time = s5k6aa->ctrls.exposure->val;
-	u16 auto_alg;
-
-	int ret = s5k6aa_read(c, REG_DBG_AUTOALG_EN, &auto_alg);
-	if (ret)
-		return ret;
-
-	v4l2_dbg(1, debug, c, "man_exp: %d, auto_exp: %d, a_alg: 0x%x\n",
-		 exp_time, value, auto_alg);
-
-	if (value == V4L2_EXPOSURE_AUTO) {
-		auto_alg |= AALG_AE_EN_MASK | AALG_DIVLEI_EN_MASK;
-	} else {
-		ret = s5k6aa_set_user_exposure(c, exp_time);
-		if (ret)
-			return ret;
-		ret = s5k6aa_set_user_gain(c, s5k6aa->ctrls.gain->val);
-		if (ret)
-			return ret;
-		auto_alg &= ~(AALG_AE_EN_MASK | AALG_DIVLEI_EN_MASK);
-	}
-
-	return s5k6aa_write(c, REG_DBG_AUTOALG_EN, auto_alg);
-}
-
-static int s5k6aa_set_anti_flicker(struct s5k6aa *s5k6aa, int value)
-{
-	struct i2c_client *client = v4l2_get_subdevdata(&s5k6aa->sd);
-	u16 auto_alg;
-	int ret;
-
-	ret = s5k6aa_read(client, REG_DBG_AUTOALG_EN, &auto_alg);
-	if (ret)
-		return ret;
-
-	if (value == V4L2_CID_POWER_LINE_FREQUENCY_AUTO) {
-		auto_alg |= AALG_FLICKER_EN_MASK;
-	} else {
-		auto_alg &= ~AALG_FLICKER_EN_MASK;
-		/* The V4L2_CID_LINE_FREQUENCY control values match
-		 * the register values */
-		ret = s5k6aa_write(client, REG_SF_FLICKER_QUANT, value);
-		if (ret)
-			return ret;
-		ret = s5k6aa_write(client, REG_SF_FLICKER_QUANT_CHG, 1);
-		if (ret)
-			return ret;
-	}
-
-	return s5k6aa_write(client, REG_DBG_AUTOALG_EN, auto_alg);
-}
-
-static int s5k6aa_set_colorfx(struct s5k6aa *s5k6aa, int val)
-{
-	struct i2c_client *client = v4l2_get_subdevdata(&s5k6aa->sd);
-	static const struct v4l2_control colorfx[] = {
-		{ V4L2_COLORFX_NONE,	 0 },
-		{ V4L2_COLORFX_BW,	 1 },
-		{ V4L2_COLORFX_NEGATIVE, 2 },
-		{ V4L2_COLORFX_SEPIA,	 3 },
-		{ V4L2_COLORFX_SKY_BLUE, 4 },
-		{ V4L2_COLORFX_SKETCH,	 5 },
-	};
-	int i;
-
-	for (i = 0; i < ARRAY_SIZE(colorfx); i++) {
-		if (colorfx[i].id == val)
-			return s5k6aa_write(client, REG_G_SPEC_EFFECTS,
-					    colorfx[i].value);
-	}
-	return -EINVAL;
-}
-
-static int s5k6aa_preview_config_status(struct i2c_client *client)
-{
-	u16 error = 0;
-	int ret = s5k6aa_read(client, REG_G_PREV_CFG_ERROR, &error);
-
-	v4l2_dbg(1, debug, client, "error: 0x%x (%d)\n", error, ret);
-	return ret ? ret : (error ? -EINVAL : 0);
-}
-
-static int s5k6aa_get_pixfmt_index(struct s5k6aa *s5k6aa,
-				   struct v4l2_mbus_framefmt *mf)
-{
-	unsigned int i;
-
-	for (i = 0; i < ARRAY_SIZE(s5k6aa_formats); i++)
-		if (mf->colorspace == s5k6aa_formats[i].colorspace &&
-		    mf->code == s5k6aa_formats[i].code)
-			return i;
-	return 0;
-}
-
-static int s5k6aa_set_output_framefmt(struct s5k6aa *s5k6aa,
-				      struct s5k6aa_preset *preset)
-{
-	struct i2c_client *client = v4l2_get_subdevdata(&s5k6aa->sd);
-	int fmt_index = s5k6aa_get_pixfmt_index(s5k6aa, &preset->mbus_fmt);
-	int ret;
-
-	ret = s5k6aa_write(client, REG_P_OUT_WIDTH(preset->index),
-			   preset->mbus_fmt.width);
-	if (!ret)
-		ret = s5k6aa_write(client, REG_P_OUT_HEIGHT(preset->index),
-				   preset->mbus_fmt.height);
-	if (!ret)
-		ret = s5k6aa_write(client, REG_P_FMT(preset->index),
-				   s5k6aa_formats[fmt_index].reg_p_fmt);
-	return ret;
-}
-
-static int s5k6aa_set_input_params(struct s5k6aa *s5k6aa)
-{
-	struct i2c_client *c = v4l2_get_subdevdata(&s5k6aa->sd);
-	struct v4l2_rect *r = &s5k6aa->ccd_rect;
-	int ret;
-
-	ret = s5k6aa_write(c, REG_G_PREVZOOM_IN_WIDTH, r->width);
-	if (!ret)
-		ret = s5k6aa_write(c, REG_G_PREVZOOM_IN_HEIGHT, r->height);
-	if (!ret)
-		ret = s5k6aa_write(c, REG_G_PREVZOOM_IN_XOFFS, r->left);
-	if (!ret)
-		ret = s5k6aa_write(c, REG_G_PREVZOOM_IN_YOFFS, r->top);
-	if (!ret)
-		ret = s5k6aa_write(c, REG_G_INPUTS_CHANGE_REQ, 1);
-	if (!ret)
-		s5k6aa->apply_crop = 0;
-
-	return ret;
-}
-
-/**
- * s5k6aa_configure_video_bus - configure the video output interface
- * @s5k6aa: pointer to &struct s5k6aa describing the device
- * @bus_type: video bus type: parallel or MIPI-CSI
- * @nlanes: number of MIPI lanes to be used (MIPI-CSI only)
- *
- * Note: Only parallel bus operation has been tested.
- */
-static int s5k6aa_configure_video_bus(struct s5k6aa *s5k6aa,
-				      enum v4l2_mbus_type bus_type, int nlanes)
-{
-	struct i2c_client *client = v4l2_get_subdevdata(&s5k6aa->sd);
-	u16 cfg = 0;
-	int ret;
-
-	/*
-	 * TODO: The sensor is supposed to support BT.601 and BT.656
-	 * but there is nothing indicating how to switch between both
-	 * in the datasheet. For now default BT.601 interface is assumed.
-	 */
-	if (bus_type == V4L2_MBUS_CSI2_DPHY)
-		cfg = nlanes;
-	else if (bus_type != V4L2_MBUS_PARALLEL)
-		return -EINVAL;
-
-	ret = s5k6aa_write(client, REG_OIF_EN_MIPI_LANES, cfg);
-	if (ret)
-		return ret;
-	return s5k6aa_write(client, REG_OIF_CFG_CHG, 1);
-}
-
-/* This function should be called when switching to new user configuration set*/
-static int s5k6aa_new_config_sync(struct i2c_client *client, int timeout,
-				  int cid)
-{
-	unsigned long end = jiffies + msecs_to_jiffies(timeout);
-	u16 reg = 1;
-	int ret;
-
-	ret = s5k6aa_write(client, REG_G_ACTIVE_PREV_CFG, cid);
-	if (!ret)
-		ret = s5k6aa_write(client, REG_G_PREV_CFG_CHG, 1);
-	if (!ret)
-		ret = s5k6aa_write(client, REG_G_NEW_CFG_SYNC, 1);
-	if (timeout == 0)
-		return ret;
-
-	while (ret >= 0 && time_is_after_jiffies(end)) {
-		ret = s5k6aa_read(client, REG_G_NEW_CFG_SYNC, &reg);
-		if (!reg)
-			return 0;
-		usleep_range(1000, 5000);
-	}
-	return ret ? ret : -ETIMEDOUT;
-}
-
-/**
- * s5k6aa_set_prev_config - write user preview register set
- * @s5k6aa: pointer to &struct s5k6aa describing the device
- * @preset: s5kaa preset to be applied
- *
- * Configure output resolution and color format, pixel clock
- * frequency range, device frame rate type and frame period range.
- */
-static int s5k6aa_set_prev_config(struct s5k6aa *s5k6aa,
-				  struct s5k6aa_preset *preset)
-{
-	struct i2c_client *client = v4l2_get_subdevdata(&s5k6aa->sd);
-	int idx = preset->index;
-	u16 frame_rate_q;
-	int ret;
-
-	if (s5k6aa->fiv->reg_fr_time >= S5K6AA_MAX_HIGHRES_FR_TIME)
-		frame_rate_q = FR_RATE_Q_BEST_FRRATE;
-	else
-		frame_rate_q = FR_RATE_Q_BEST_QUALITY;
-
-	ret = s5k6aa_set_output_framefmt(s5k6aa, preset);
-	if (!ret)
-		ret = s5k6aa_write(client, REG_P_MAX_OUT_RATE(idx),
-				   s5k6aa->pclk_fmax);
-	if (!ret)
-		ret = s5k6aa_write(client, REG_P_MIN_OUT_RATE(idx),
-				   s5k6aa->pclk_fmin);
-	if (!ret)
-		ret = s5k6aa_write(client, REG_P_CLK_INDEX(idx),
-				   preset->clk_id);
-	if (!ret)
-		ret = s5k6aa_write(client, REG_P_FR_RATE_TYPE(idx),
-				   FR_RATE_DYNAMIC);
-	if (!ret)
-		ret = s5k6aa_write(client, REG_P_FR_RATE_Q_TYPE(idx),
-				   frame_rate_q);
-	if (!ret)
-		ret = s5k6aa_write(client, REG_P_MAX_FR_TIME(idx),
-				   s5k6aa->fiv->reg_fr_time + 33);
-	if (!ret)
-		ret = s5k6aa_write(client, REG_P_MIN_FR_TIME(idx),
-				   s5k6aa->fiv->reg_fr_time - 33);
-	if (!ret)
-		ret = s5k6aa_new_config_sync(client, 250, idx);
-	if (!ret)
-		ret = s5k6aa_preview_config_status(client);
-	if (!ret)
-		s5k6aa->apply_cfg = 0;
-
-	v4l2_dbg(1, debug, client, "Frame interval: %d +/- 3.3ms. (%d)\n",
-		 s5k6aa->fiv->reg_fr_time, ret);
-	return ret;
-}
-
-/**
- * s5k6aa_initialize_isp - basic ISP MCU initialization
- * @sd: pointer to V4L2 sub-device descriptor
- *
- * Configure AHB addresses for registers read/write; configure PLLs for
- * required output pixel clock. The ISP power supply needs to be already
- * enabled, with an optional H/W reset.
- * Locking: called with s5k6aa.lock mutex held.
- */
-static int s5k6aa_initialize_isp(struct v4l2_subdev *sd)
-{
-	struct i2c_client *client = v4l2_get_subdevdata(sd);
-	struct s5k6aa *s5k6aa = to_s5k6aa(sd);
-	int ret;
-
-	s5k6aa->apply_crop = 1;
-	s5k6aa->apply_cfg = 1;
-	msleep(100);
-
-	ret = s5k6aa_set_ahb_address(client);
-	if (ret)
-		return ret;
-	ret = s5k6aa_configure_video_bus(s5k6aa, s5k6aa->bus_type,
-					 s5k6aa->mipi_lanes);
-	if (ret)
-		return ret;
-	ret = s5k6aa_write_array(sd, s5k6aa_analog_config);
-	if (ret)
-		return ret;
-	msleep(20);
-
-	return s5k6aa_configure_pixel_clocks(s5k6aa);
-}
-
-static int s5k6aa_gpio_set_value(struct s5k6aa *priv, int id, u32 val)
-{
-	if (!gpio_is_valid(priv->gpio[id].gpio))
-		return 0;
-	gpio_set_value(priv->gpio[id].gpio, !!val);
-	return 1;
-}
-
-static int s5k6aa_gpio_assert(struct s5k6aa *priv, int id)
-{
-	return s5k6aa_gpio_set_value(priv, id, priv->gpio[id].level);
-}
-
-static int s5k6aa_gpio_deassert(struct s5k6aa *priv, int id)
-{
-	return s5k6aa_gpio_set_value(priv, id, !priv->gpio[id].level);
-}
-
-static int __s5k6aa_power_on(struct s5k6aa *s5k6aa)
-{
-	int ret;
-
-	ret = regulator_bulk_enable(S5K6AA_NUM_SUPPLIES, s5k6aa->supplies);
-	if (ret)
-		return ret;
-	if (s5k6aa_gpio_deassert(s5k6aa, STBY))
-		usleep_range(150, 200);
-
-	if (s5k6aa->s_power)
-		ret = s5k6aa->s_power(1);
-	usleep_range(4000, 5000);
-
-	if (s5k6aa_gpio_deassert(s5k6aa, RSET))
-		msleep(20);
-
-	return ret;
-}
-
-static int __s5k6aa_power_off(struct s5k6aa *s5k6aa)
-{
-	int ret;
-
-	if (s5k6aa_gpio_assert(s5k6aa, RSET))
-		usleep_range(100, 150);
-
-	if (s5k6aa->s_power) {
-		ret = s5k6aa->s_power(0);
-		if (ret)
-			return ret;
-	}
-	if (s5k6aa_gpio_assert(s5k6aa, STBY))
-		usleep_range(50, 100);
-	s5k6aa->streaming = 0;
-
-	return regulator_bulk_disable(S5K6AA_NUM_SUPPLIES, s5k6aa->supplies);
-}
-
-/*
- * V4L2 subdev core and video operations
- */
-static int s5k6aa_set_power(struct v4l2_subdev *sd, int on)
-{
-	struct s5k6aa *s5k6aa = to_s5k6aa(sd);
-	int ret = 0;
-
-	mutex_lock(&s5k6aa->lock);
-
-	if (s5k6aa->power == !on) {
-		if (on) {
-			ret = __s5k6aa_power_on(s5k6aa);
-			if (!ret)
-				ret = s5k6aa_initialize_isp(sd);
-		} else {
-			ret = __s5k6aa_power_off(s5k6aa);
-		}
-
-		if (!ret)
-			s5k6aa->power += on ? 1 : -1;
-	}
-
-	mutex_unlock(&s5k6aa->lock);
-
-	if (!on || ret || s5k6aa->power != 1)
-		return ret;
-
-	return v4l2_ctrl_handler_setup(sd->ctrl_handler);
-}
-
-static int __s5k6aa_stream(struct s5k6aa *s5k6aa, int enable)
-{
-	struct i2c_client *client = v4l2_get_subdevdata(&s5k6aa->sd);
-	int ret = 0;
-
-	ret = s5k6aa_write(client, REG_G_ENABLE_PREV, enable);
-	if (!ret)
-		ret = s5k6aa_write(client, REG_G_ENABLE_PREV_CHG, 1);
-	if (!ret)
-		s5k6aa->streaming = enable;
-
-	return ret;
-}
-
-static int s5k6aa_s_stream(struct v4l2_subdev *sd, int on)
-{
-	struct s5k6aa *s5k6aa = to_s5k6aa(sd);
-	int ret = 0;
-
-	mutex_lock(&s5k6aa->lock);
-
-	if (s5k6aa->streaming == !on) {
-		if (!ret && s5k6aa->apply_cfg)
-			ret = s5k6aa_set_prev_config(s5k6aa, s5k6aa->preset);
-		if (s5k6aa->apply_crop)
-			ret = s5k6aa_set_input_params(s5k6aa);
-		if (!ret)
-			ret = __s5k6aa_stream(s5k6aa, !!on);
-	}
-	mutex_unlock(&s5k6aa->lock);
-
-	return ret;
-}
-
-static int s5k6aa_g_frame_interval(struct v4l2_subdev *sd,
-				   struct v4l2_subdev_frame_interval *fi)
-{
-	struct s5k6aa *s5k6aa = to_s5k6aa(sd);
-
-	mutex_lock(&s5k6aa->lock);
-	fi->interval = s5k6aa->fiv->interval;
-	mutex_unlock(&s5k6aa->lock);
-
-	return 0;
-}
-
-static int __s5k6aa_set_frame_interval(struct s5k6aa *s5k6aa,
-				       struct v4l2_subdev_frame_interval *fi)
-{
-	struct v4l2_mbus_framefmt *mbus_fmt = &s5k6aa->preset->mbus_fmt;
-	const struct s5k6aa_interval *fiv = &s5k6aa_intervals[0];
-	unsigned int err, min_err = UINT_MAX;
-	unsigned int i, fr_time;
-
-	if (fi->interval.denominator == 0)
-		return -EINVAL;
-
-	fr_time = fi->interval.numerator * 10000 / fi->interval.denominator;
-
-	for (i = 0; i < ARRAY_SIZE(s5k6aa_intervals); i++) {
-		const struct s5k6aa_interval *iv = &s5k6aa_intervals[i];
-
-		if (mbus_fmt->width > iv->size.width ||
-		    mbus_fmt->height > iv->size.height)
-			continue;
-
-		err = abs(iv->reg_fr_time - fr_time);
-		if (err < min_err) {
-			fiv = iv;
-			min_err = err;
-		}
-	}
-	s5k6aa->fiv = fiv;
-
-	v4l2_dbg(1, debug, &s5k6aa->sd, "Changed frame interval to %d us\n",
-		 fiv->reg_fr_time * 100);
-	return 0;
-}
-
-static int s5k6aa_s_frame_interval(struct v4l2_subdev *sd,
-				   struct v4l2_subdev_frame_interval *fi)
-{
-	struct s5k6aa *s5k6aa = to_s5k6aa(sd);
-	int ret;
-
-	v4l2_dbg(1, debug, sd, "Setting %d/%d frame interval\n",
-		 fi->interval.numerator, fi->interval.denominator);
-
-	mutex_lock(&s5k6aa->lock);
-	ret = __s5k6aa_set_frame_interval(s5k6aa, fi);
-	s5k6aa->apply_cfg = 1;
-
-	mutex_unlock(&s5k6aa->lock);
-	return ret;
-}
-
-/*
- * V4L2 subdev pad level and video operations
- */
-static int s5k6aa_enum_frame_interval(struct v4l2_subdev *sd,
-			      struct v4l2_subdev_state *sd_state,
-			      struct v4l2_subdev_frame_interval_enum *fie)
-{
-	struct s5k6aa *s5k6aa = to_s5k6aa(sd);
-	const struct s5k6aa_interval *fi;
-	int ret = 0;
-
-	if (fie->index >= ARRAY_SIZE(s5k6aa_intervals))
-		return -EINVAL;
-
-	v4l_bound_align_image(&fie->width, S5K6AA_WIN_WIDTH_MIN,
-			      S5K6AA_WIN_WIDTH_MAX, 1,
-			      &fie->height, S5K6AA_WIN_HEIGHT_MIN,
-			      S5K6AA_WIN_HEIGHT_MAX, 1, 0);
-
-	mutex_lock(&s5k6aa->lock);
-	fi = &s5k6aa_intervals[fie->index];
-	if (fie->width > fi->size.width || fie->height > fi->size.height)
-		ret = -EINVAL;
-	else
-		fie->interval = fi->interval;
-	mutex_unlock(&s5k6aa->lock);
-
-	return ret;
-}
-
-static int s5k6aa_enum_mbus_code(struct v4l2_subdev *sd,
-				 struct v4l2_subdev_state *sd_state,
-				 struct v4l2_subdev_mbus_code_enum *code)
-{
-	if (code->index >= ARRAY_SIZE(s5k6aa_formats))
-		return -EINVAL;
-
-	code->code = s5k6aa_formats[code->index].code;
-	return 0;
-}
-
-static int s5k6aa_enum_frame_size(struct v4l2_subdev *sd,
-				  struct v4l2_subdev_state *sd_state,
-				  struct v4l2_subdev_frame_size_enum *fse)
-{
-	int i = ARRAY_SIZE(s5k6aa_formats);
-
-	if (fse->index > 0)
-		return -EINVAL;
-
-	while (--i)
-		if (fse->code == s5k6aa_formats[i].code)
-			break;
-
-	fse->code = s5k6aa_formats[i].code;
-	fse->min_width  = S5K6AA_WIN_WIDTH_MIN;
-	fse->max_width  = S5K6AA_WIN_WIDTH_MAX;
-	fse->max_height = S5K6AA_WIN_HEIGHT_MIN;
-	fse->min_height = S5K6AA_WIN_HEIGHT_MAX;
-
-	return 0;
-}
-
-static struct v4l2_rect *
-__s5k6aa_get_crop_rect(struct s5k6aa *s5k6aa,
-		       struct v4l2_subdev_state *sd_state,
-		       enum v4l2_subdev_format_whence which)
-{
-	if (which == V4L2_SUBDEV_FORMAT_ACTIVE)
-		return &s5k6aa->ccd_rect;
-
-	WARN_ON(which != V4L2_SUBDEV_FORMAT_TRY);
-	return v4l2_subdev_get_try_crop(&s5k6aa->sd, sd_state, 0);
-}
-
-static void s5k6aa_try_format(struct s5k6aa *s5k6aa,
-			      struct v4l2_mbus_framefmt *mf)
-{
-	unsigned int index;
-
-	v4l_bound_align_image(&mf->width, S5K6AA_WIN_WIDTH_MIN,
-			      S5K6AA_WIN_WIDTH_MAX, 1,
-			      &mf->height, S5K6AA_WIN_HEIGHT_MIN,
-			      S5K6AA_WIN_HEIGHT_MAX, 1, 0);
-
-	if (mf->colorspace != V4L2_COLORSPACE_JPEG &&
-	    mf->colorspace != V4L2_COLORSPACE_REC709)
-		mf->colorspace = V4L2_COLORSPACE_JPEG;
-
-	index = s5k6aa_get_pixfmt_index(s5k6aa, mf);
-
-	mf->colorspace	= s5k6aa_formats[index].colorspace;
-	mf->code	= s5k6aa_formats[index].code;
-	mf->field	= V4L2_FIELD_NONE;
-}
-
-static int s5k6aa_get_fmt(struct v4l2_subdev *sd,
-			  struct v4l2_subdev_state *sd_state,
-			  struct v4l2_subdev_format *fmt)
-{
-	struct s5k6aa *s5k6aa = to_s5k6aa(sd);
-	struct v4l2_mbus_framefmt *mf;
-
-	memset(fmt->reserved, 0, sizeof(fmt->reserved));
-
-	if (fmt->which == V4L2_SUBDEV_FORMAT_TRY) {
-		mf = v4l2_subdev_get_try_format(sd, sd_state, 0);
-		fmt->format = *mf;
-		return 0;
-	}
-
-	mutex_lock(&s5k6aa->lock);
-	fmt->format = s5k6aa->preset->mbus_fmt;
-	mutex_unlock(&s5k6aa->lock);
-
-	return 0;
-}
-
-static int s5k6aa_set_fmt(struct v4l2_subdev *sd,
-			  struct v4l2_subdev_state *sd_state,
-			  struct v4l2_subdev_format *fmt)
-{
-	struct s5k6aa *s5k6aa = to_s5k6aa(sd);
-	struct s5k6aa_preset *preset = s5k6aa->preset;
-	struct v4l2_mbus_framefmt *mf;
-	struct v4l2_rect *crop;
-	int ret = 0;
-
-	mutex_lock(&s5k6aa->lock);
-	s5k6aa_try_format(s5k6aa, &fmt->format);
-
-	if (fmt->which == V4L2_SUBDEV_FORMAT_TRY) {
-		mf = v4l2_subdev_get_try_format(sd, sd_state, fmt->pad);
-		crop = v4l2_subdev_get_try_crop(sd, sd_state, 0);
-	} else {
-		if (s5k6aa->streaming) {
-			ret = -EBUSY;
-		} else {
-			mf = &preset->mbus_fmt;
-			crop = &s5k6aa->ccd_rect;
-			s5k6aa->apply_cfg = 1;
-		}
-	}
-
-	if (ret == 0) {
-		struct v4l2_subdev_frame_interval fiv = {
-			.interval = {0, 1}
-		};
-
-		*mf = fmt->format;
-		/*
-		 * Make sure the crop window is valid, i.e. its size is
-		 * greater than the output window, as the ISP supports
-		 * only down-scaling.
-		 */
-		crop->width = clamp_t(unsigned int, crop->width, mf->width,
-				      S5K6AA_WIN_WIDTH_MAX);
-		crop->height = clamp_t(unsigned int, crop->height, mf->height,
-				       S5K6AA_WIN_HEIGHT_MAX);
-		crop->left = clamp_t(unsigned int, crop->left, 0,
-				     S5K6AA_WIN_WIDTH_MAX - crop->width);
-		crop->top  = clamp_t(unsigned int, crop->top, 0,
-				     S5K6AA_WIN_HEIGHT_MAX - crop->height);
-
-		/* Reset to minimum possible frame interval */
-		ret = __s5k6aa_set_frame_interval(s5k6aa, &fiv);
-	}
-	mutex_unlock(&s5k6aa->lock);
-
-	return ret;
-}
-
-static int s5k6aa_get_selection(struct v4l2_subdev *sd,
-				struct v4l2_subdev_state *sd_state,
-				struct v4l2_subdev_selection *sel)
-{
-	struct s5k6aa *s5k6aa = to_s5k6aa(sd);
-	struct v4l2_rect *rect;
-
-	if (sel->target != V4L2_SEL_TGT_CROP)
-		return -EINVAL;
-
-	memset(sel->reserved, 0, sizeof(sel->reserved));
-
-	mutex_lock(&s5k6aa->lock);
-	rect = __s5k6aa_get_crop_rect(s5k6aa, sd_state, sel->which);
-	sel->r = *rect;
-	mutex_unlock(&s5k6aa->lock);
-
-	v4l2_dbg(1, debug, sd, "Current crop rectangle: (%d,%d)/%dx%d\n",
-		 rect->left, rect->top, rect->width, rect->height);
-
-	return 0;
-}
-
-static int s5k6aa_set_selection(struct v4l2_subdev *sd,
-				struct v4l2_subdev_state *sd_state,
-				struct v4l2_subdev_selection *sel)
-{
-	struct s5k6aa *s5k6aa = to_s5k6aa(sd);
-	struct v4l2_mbus_framefmt *mf;
-	unsigned int max_x, max_y;
-	struct v4l2_rect *crop_r;
-
-	if (sel->target != V4L2_SEL_TGT_CROP)
-		return -EINVAL;
-
-	mutex_lock(&s5k6aa->lock);
-	crop_r = __s5k6aa_get_crop_rect(s5k6aa, sd_state, sel->which);
-
-	if (sel->which == V4L2_SUBDEV_FORMAT_ACTIVE) {
-		mf = &s5k6aa->preset->mbus_fmt;
-		s5k6aa->apply_crop = 1;
-	} else {
-		mf = v4l2_subdev_get_try_format(sd, sd_state, 0);
-	}
-	v4l_bound_align_image(&sel->r.width, mf->width,
-			      S5K6AA_WIN_WIDTH_MAX, 1,
-			      &sel->r.height, mf->height,
-			      S5K6AA_WIN_HEIGHT_MAX, 1, 0);
-
-	max_x = (S5K6AA_WIN_WIDTH_MAX - sel->r.width) & ~1;
-	max_y = (S5K6AA_WIN_HEIGHT_MAX - sel->r.height) & ~1;
-
-	sel->r.left = clamp_t(unsigned int, sel->r.left, 0, max_x);
-	sel->r.top  = clamp_t(unsigned int, sel->r.top, 0, max_y);
-
-	*crop_r = sel->r;
-
-	mutex_unlock(&s5k6aa->lock);
-
-	v4l2_dbg(1, debug, sd, "Set crop rectangle: (%d,%d)/%dx%d\n",
-		 crop_r->left, crop_r->top, crop_r->width, crop_r->height);
-
-	return 0;
-}
-
-static const struct v4l2_subdev_pad_ops s5k6aa_pad_ops = {
-	.enum_mbus_code		= s5k6aa_enum_mbus_code,
-	.enum_frame_size	= s5k6aa_enum_frame_size,
-	.enum_frame_interval	= s5k6aa_enum_frame_interval,
-	.get_fmt		= s5k6aa_get_fmt,
-	.set_fmt		= s5k6aa_set_fmt,
-	.get_selection		= s5k6aa_get_selection,
-	.set_selection		= s5k6aa_set_selection,
-};
-
-static const struct v4l2_subdev_video_ops s5k6aa_video_ops = {
-	.g_frame_interval	= s5k6aa_g_frame_interval,
-	.s_frame_interval	= s5k6aa_s_frame_interval,
-	.s_stream		= s5k6aa_s_stream,
-};
-
-/*
- * V4L2 subdev controls
- */
-
-static int s5k6aa_s_ctrl(struct v4l2_ctrl *ctrl)
-{
-	struct v4l2_subdev *sd = ctrl_to_sd(ctrl);
-	struct i2c_client *client = v4l2_get_subdevdata(sd);
-	struct s5k6aa *s5k6aa = to_s5k6aa(sd);
-	int idx, err = 0;
-
-	v4l2_dbg(1, debug, sd, "ctrl: 0x%x, value: %d\n", ctrl->id, ctrl->val);
-
-	mutex_lock(&s5k6aa->lock);
-	/*
-	 * If the device is not powered up by the host driver do
-	 * not apply any controls to H/W at this time. Instead
-	 * the controls will be restored right after power-up.
-	 */
-	if (s5k6aa->power == 0)
-		goto unlock;
-	idx = s5k6aa->preset->index;
-
-	switch (ctrl->id) {
-	case V4L2_CID_AUTO_WHITE_BALANCE:
-		err = s5k6aa_set_awb(s5k6aa, ctrl->val);
-		break;
-
-	case V4L2_CID_BRIGHTNESS:
-		err = s5k6aa_write(client, REG_USER_BRIGHTNESS, ctrl->val);
-		break;
-
-	case V4L2_CID_COLORFX:
-		err = s5k6aa_set_colorfx(s5k6aa, ctrl->val);
-		break;
-
-	case V4L2_CID_CONTRAST:
-		err = s5k6aa_write(client, REG_USER_CONTRAST, ctrl->val);
-		break;
-
-	case V4L2_CID_EXPOSURE_AUTO:
-		err = s5k6aa_set_auto_exposure(s5k6aa, ctrl->val);
-		break;
-
-	case V4L2_CID_HFLIP:
-		err = s5k6aa_set_mirror(s5k6aa, ctrl->val);
-		if (err)
-			break;
-		err = s5k6aa_write(client, REG_G_PREV_CFG_CHG, 1);
-		break;
-
-	case V4L2_CID_POWER_LINE_FREQUENCY:
-		err = s5k6aa_set_anti_flicker(s5k6aa, ctrl->val);
-		break;
-
-	case V4L2_CID_SATURATION:
-		err = s5k6aa_write(client, REG_USER_SATURATION, ctrl->val);
-		break;
-
-	case V4L2_CID_SHARPNESS:
-		err = s5k6aa_write(client, REG_USER_SHARPBLUR, ctrl->val);
-		break;
-
-	case V4L2_CID_WHITE_BALANCE_TEMPERATURE:
-		err = s5k6aa_write(client, REG_P_COLORTEMP(idx), ctrl->val);
-		if (err)
-			break;
-		err = s5k6aa_write(client, REG_G_PREV_CFG_CHG, 1);
-		break;
-	}
-unlock:
-	mutex_unlock(&s5k6aa->lock);
-	return err;
-}
-
-static const struct v4l2_ctrl_ops s5k6aa_ctrl_ops = {
-	.s_ctrl	= s5k6aa_s_ctrl,
-};
-
-static int s5k6aa_log_status(struct v4l2_subdev *sd)
-{
-	v4l2_ctrl_handler_log_status(sd->ctrl_handler, sd->name);
-	return 0;
-}
-
-#define V4L2_CID_RED_GAIN	(V4L2_CTRL_CLASS_CAMERA | 0x1001)
-#define V4L2_CID_GREEN_GAIN	(V4L2_CTRL_CLASS_CAMERA | 0x1002)
-#define V4L2_CID_BLUE_GAIN	(V4L2_CTRL_CLASS_CAMERA | 0x1003)
-
-static const struct v4l2_ctrl_config s5k6aa_ctrls[] = {
-	{
-		.ops	= &s5k6aa_ctrl_ops,
-		.id	= V4L2_CID_RED_GAIN,
-		.type	= V4L2_CTRL_TYPE_INTEGER,
-		.name	= "Gain, Red",
-		.min	= 0,
-		.max	= 256,
-		.def	= 127,
-		.step	= 1,
-	}, {
-		.ops	= &s5k6aa_ctrl_ops,
-		.id	= V4L2_CID_GREEN_GAIN,
-		.type	= V4L2_CTRL_TYPE_INTEGER,
-		.name	= "Gain, Green",
-		.min	= 0,
-		.max	= 256,
-		.def	= 127,
-		.step	= 1,
-	}, {
-		.ops	= &s5k6aa_ctrl_ops,
-		.id	= V4L2_CID_BLUE_GAIN,
-		.type	= V4L2_CTRL_TYPE_INTEGER,
-		.name	= "Gain, Blue",
-		.min	= 0,
-		.max	= 256,
-		.def	= 127,
-		.step	= 1,
-	},
-};
-
-static int s5k6aa_initialize_ctrls(struct s5k6aa *s5k6aa)
-{
-	const struct v4l2_ctrl_ops *ops = &s5k6aa_ctrl_ops;
-	struct s5k6aa_ctrls *ctrls = &s5k6aa->ctrls;
-	struct v4l2_ctrl_handler *hdl = &ctrls->handler;
-
-	int ret = v4l2_ctrl_handler_init(hdl, 16);
-	if (ret)
-		return ret;
-	/* Auto white balance cluster */
-	ctrls->awb = v4l2_ctrl_new_std(hdl, ops, V4L2_CID_AUTO_WHITE_BALANCE,
-				       0, 1, 1, 1);
-	ctrls->gain_red = v4l2_ctrl_new_custom(hdl, &s5k6aa_ctrls[0], NULL);
-	ctrls->gain_green = v4l2_ctrl_new_custom(hdl, &s5k6aa_ctrls[1], NULL);
-	ctrls->gain_blue = v4l2_ctrl_new_custom(hdl, &s5k6aa_ctrls[2], NULL);
-	v4l2_ctrl_auto_cluster(4, &ctrls->awb, 0, false);
-
-	ctrls->hflip = v4l2_ctrl_new_std(hdl, ops, V4L2_CID_HFLIP, 0, 1, 1, 0);
-	ctrls->vflip = v4l2_ctrl_new_std(hdl, ops, V4L2_CID_VFLIP, 0, 1, 1, 0);
-	v4l2_ctrl_cluster(2, &ctrls->hflip);
-
-	ctrls->auto_exp = v4l2_ctrl_new_std_menu(hdl, ops,
-				V4L2_CID_EXPOSURE_AUTO,
-				V4L2_EXPOSURE_MANUAL, 0, V4L2_EXPOSURE_AUTO);
-	/* Exposure time: x 1 us */
-	ctrls->exposure = v4l2_ctrl_new_std(hdl, ops, V4L2_CID_EXPOSURE,
-					    0, 6000000U, 1, 100000U);
-	/* Total gain: 256 <=> 1x */
-	ctrls->gain = v4l2_ctrl_new_std(hdl, ops, V4L2_CID_GAIN,
-					0, 256, 1, 256);
-	v4l2_ctrl_auto_cluster(3, &ctrls->auto_exp, 0, false);
-
-	v4l2_ctrl_new_std_menu(hdl, ops, V4L2_CID_POWER_LINE_FREQUENCY,
-			       V4L2_CID_POWER_LINE_FREQUENCY_AUTO, 0,
-			       V4L2_CID_POWER_LINE_FREQUENCY_AUTO);
-
-	v4l2_ctrl_new_std_menu(hdl, ops, V4L2_CID_COLORFX,
-			       V4L2_COLORFX_SKY_BLUE, ~0x6f, V4L2_COLORFX_NONE);
-
-	v4l2_ctrl_new_std(hdl, ops, V4L2_CID_WHITE_BALANCE_TEMPERATURE,
-			  0, 256, 1, 0);
-
-	v4l2_ctrl_new_std(hdl, ops, V4L2_CID_SATURATION, -127, 127, 1, 0);
-	v4l2_ctrl_new_std(hdl, ops, V4L2_CID_BRIGHTNESS, -127, 127, 1, 0);
-	v4l2_ctrl_new_std(hdl, ops, V4L2_CID_CONTRAST, -127, 127, 1, 0);
-	v4l2_ctrl_new_std(hdl, ops, V4L2_CID_SHARPNESS, -127, 127, 1, 0);
-
-	if (hdl->error) {
-		ret = hdl->error;
-		v4l2_ctrl_handler_free(hdl);
-		return ret;
-	}
-
-	s5k6aa->sd.ctrl_handler = hdl;
-	return 0;
-}
-
-/*
- * V4L2 subdev internal operations
- */
-static int s5k6aa_open(struct v4l2_subdev *sd, struct v4l2_subdev_fh *fh)
-{
-	struct v4l2_mbus_framefmt *format = v4l2_subdev_get_try_format(sd,
-								       fh->state,
-								       0);
-	struct v4l2_rect *crop = v4l2_subdev_get_try_crop(sd, fh->state, 0);
-
-	format->colorspace = s5k6aa_formats[0].colorspace;
-	format->code = s5k6aa_formats[0].code;
-	format->width = S5K6AA_OUT_WIDTH_DEF;
-	format->height = S5K6AA_OUT_HEIGHT_DEF;
-	format->field = V4L2_FIELD_NONE;
-
-	crop->width = S5K6AA_WIN_WIDTH_MAX;
-	crop->height = S5K6AA_WIN_HEIGHT_MAX;
-	crop->left = 0;
-	crop->top = 0;
-
-	return 0;
-}
-
-static int s5k6aa_check_fw_revision(struct s5k6aa *s5k6aa)
-{
-	struct i2c_client *client = v4l2_get_subdevdata(&s5k6aa->sd);
-	u16 api_ver = 0, fw_rev = 0;
-
-	int ret = s5k6aa_set_ahb_address(client);
-
-	if (!ret)
-		ret = s5k6aa_read(client, REG_FW_APIVER, &api_ver);
-	if (!ret)
-		ret = s5k6aa_read(client, REG_FW_REVISION, &fw_rev);
-	if (ret) {
-		v4l2_err(&s5k6aa->sd, "FW revision check failed!\n");
-		return ret;
-	}
-
-	v4l2_info(&s5k6aa->sd, "FW API ver.: 0x%X, FW rev.: 0x%X\n",
-		  api_ver, fw_rev);
-
-	return api_ver == S5K6AAFX_FW_APIVER ? 0 : -ENODEV;
-}
-
-static int s5k6aa_registered(struct v4l2_subdev *sd)
-{
-	struct s5k6aa *s5k6aa = to_s5k6aa(sd);
-	int ret;
-
-	mutex_lock(&s5k6aa->lock);
-	ret = __s5k6aa_power_on(s5k6aa);
-	if (!ret) {
-		msleep(100);
-		ret = s5k6aa_check_fw_revision(s5k6aa);
-		__s5k6aa_power_off(s5k6aa);
-	}
-	mutex_unlock(&s5k6aa->lock);
-
-	return ret;
-}
-
-static const struct v4l2_subdev_internal_ops s5k6aa_subdev_internal_ops = {
-	.registered = s5k6aa_registered,
-	.open = s5k6aa_open,
-};
-
-static const struct v4l2_subdev_core_ops s5k6aa_core_ops = {
-	.s_power = s5k6aa_set_power,
-	.log_status = s5k6aa_log_status,
-};
-
-static const struct v4l2_subdev_ops s5k6aa_subdev_ops = {
-	.core = &s5k6aa_core_ops,
-	.pad = &s5k6aa_pad_ops,
-	.video = &s5k6aa_video_ops,
-};
-
-/*
- * GPIO setup
- */
-
-static int s5k6aa_configure_gpios(struct s5k6aa *s5k6aa,
-				  const struct s5k6aa_platform_data *pdata)
-{
-	struct i2c_client *client = v4l2_get_subdevdata(&s5k6aa->sd);
-	const struct s5k6aa_gpio *gpio;
-	unsigned long flags;
-	int ret;
-
-	s5k6aa->gpio[STBY].gpio = -EINVAL;
-	s5k6aa->gpio[RSET].gpio  = -EINVAL;
-
-	gpio = &pdata->gpio_stby;
-	if (gpio_is_valid(gpio->gpio)) {
-		flags = (gpio->level ? GPIOF_OUT_INIT_HIGH : GPIOF_OUT_INIT_LOW)
-		      | GPIOF_EXPORT;
-		ret = devm_gpio_request_one(&client->dev, gpio->gpio, flags,
-					    "S5K6AA_STBY");
-		if (ret < 0)
-			return ret;
-
-		s5k6aa->gpio[STBY] = *gpio;
-	}
-
-	gpio = &pdata->gpio_reset;
-	if (gpio_is_valid(gpio->gpio)) {
-		flags = (gpio->level ? GPIOF_OUT_INIT_HIGH : GPIOF_OUT_INIT_LOW)
-		      | GPIOF_EXPORT;
-		ret = devm_gpio_request_one(&client->dev, gpio->gpio, flags,
-					    "S5K6AA_RST");
-		if (ret < 0)
-			return ret;
-
-		s5k6aa->gpio[RSET] = *gpio;
-	}
-
-	return 0;
-}
-
-static int s5k6aa_probe(struct i2c_client *client)
-{
-	const struct s5k6aa_platform_data *pdata = client->dev.platform_data;
-	struct v4l2_subdev *sd;
-	struct s5k6aa *s5k6aa;
-	int i, ret;
-
-	if (pdata == NULL) {
-		dev_err(&client->dev, "Platform data not specified\n");
-		return -EINVAL;
-	}
-
-	if (pdata->mclk_frequency == 0) {
-		dev_err(&client->dev, "MCLK frequency not specified\n");
-		return -EINVAL;
-	}
-
-	s5k6aa = devm_kzalloc(&client->dev, sizeof(*s5k6aa), GFP_KERNEL);
-	if (!s5k6aa)
-		return -ENOMEM;
-
-	mutex_init(&s5k6aa->lock);
-
-	s5k6aa->mclk_frequency = pdata->mclk_frequency;
-	s5k6aa->bus_type = pdata->bus_type;
-	s5k6aa->mipi_lanes = pdata->nlanes;
-	s5k6aa->s_power	= pdata->set_power;
-	s5k6aa->inv_hflip = pdata->horiz_flip;
-	s5k6aa->inv_vflip = pdata->vert_flip;
-
-	sd = &s5k6aa->sd;
-	v4l2_i2c_subdev_init(sd, client, &s5k6aa_subdev_ops);
-	/* Static name; NEVER use in new drivers! */
-	strscpy(sd->name, DRIVER_NAME, sizeof(sd->name));
-
-	sd->internal_ops = &s5k6aa_subdev_internal_ops;
-	sd->flags |= V4L2_SUBDEV_FL_HAS_DEVNODE;
-
-	s5k6aa->pad.flags = MEDIA_PAD_FL_SOURCE;
-	sd->entity.function = MEDIA_ENT_F_CAM_SENSOR;
-	ret = media_entity_pads_init(&sd->entity, 1, &s5k6aa->pad);
-	if (ret)
-		return ret;
-
-	ret = s5k6aa_configure_gpios(s5k6aa, pdata);
-	if (ret)
-		goto out_err;
-
-	for (i = 0; i < S5K6AA_NUM_SUPPLIES; i++)
-		s5k6aa->supplies[i].supply = s5k6aa_supply_names[i];
-
-	ret = devm_regulator_bulk_get(&client->dev, S5K6AA_NUM_SUPPLIES,
-				 s5k6aa->supplies);
-	if (ret) {
-		dev_err(&client->dev, "Failed to get regulators\n");
-		goto out_err;
-	}
-
-	ret = s5k6aa_initialize_ctrls(s5k6aa);
-	if (ret)
-		goto out_err;
-
-	s5k6aa_presets_data_init(s5k6aa);
-
-	s5k6aa->ccd_rect.width = S5K6AA_WIN_WIDTH_MAX;
-	s5k6aa->ccd_rect.height	= S5K6AA_WIN_HEIGHT_MAX;
-	s5k6aa->ccd_rect.left = 0;
-	s5k6aa->ccd_rect.top = 0;
-
-	return 0;
-
-out_err:
-	media_entity_cleanup(&s5k6aa->sd.entity);
-	return ret;
-}
-
-static void s5k6aa_remove(struct i2c_client *client)
-{
-	struct v4l2_subdev *sd = i2c_get_clientdata(client);
-
-	v4l2_device_unregister_subdev(sd);
-	v4l2_ctrl_handler_free(sd->ctrl_handler);
-	media_entity_cleanup(&sd->entity);
-}
-
-static const struct i2c_device_id s5k6aa_id[] = {
-	{ DRIVER_NAME, 0 },
-	{ },
-};
-MODULE_DEVICE_TABLE(i2c, s5k6aa_id);
-
-
-static struct i2c_driver s5k6aa_i2c_driver = {
-	.driver = {
-		.name = DRIVER_NAME
-	},
-	.probe_new	= s5k6aa_probe,
-	.remove		= s5k6aa_remove,
-	.id_table	= s5k6aa_id,
-};
-
-module_i2c_driver(s5k6aa_i2c_driver);
-
-MODULE_DESCRIPTION("Samsung S5K6AA(FX) SXGA camera driver");
-MODULE_AUTHOR("Sylwester Nawrocki <s.nawrocki@samsung.com>");
-MODULE_LICENSE("GPL");
diff --git a/include/media/i2c/s5k6aa.h b/include/media/i2c/s5k6aa.h
deleted file mode 100644
index eb3444d8b731..000000000000
--- a/include/media/i2c/s5k6aa.h
+++ /dev/null
@@ -1,48 +0,0 @@
-/* SPDX-License-Identifier: GPL-2.0-or-later */
-/*
- * S5K6AAFX camera sensor driver header
- *
- * Copyright (C) 2011 Samsung Electronics Co., Ltd.
- */
-
-#ifndef S5K6AA_H
-#define S5K6AA_H
-
-#include <media/v4l2-mediabus.h>
-
-/**
- * struct s5k6aa_gpio - data structure describing a GPIO
- * @gpio:  GPIO number
- * @level: indicates active state of the @gpio
- */
-struct s5k6aa_gpio {
-	int gpio;
-	int level;
-};
-
-/**
- * struct s5k6aa_platform_data - s5k6aa driver platform data
- * @set_power:   an additional callback to the board code, called
- *               after enabling the regulators and before switching
- *               the sensor off
- * @mclk_frequency: sensor's master clock frequency in Hz
- * @gpio_reset:  GPIO driving RESET pin
- * @gpio_stby:   GPIO driving STBY pin
- * @bus_type:    bus type
- * @nlanes:      maximum number of MIPI-CSI lanes used
- * @horiz_flip:  default horizontal image flip value, non zero to enable
- * @vert_flip:   default vertical image flip value, non zero to enable
- */
-
-struct s5k6aa_platform_data {
-	int (*set_power)(int enable);
-	unsigned long mclk_frequency;
-	struct s5k6aa_gpio gpio_reset;
-	struct s5k6aa_gpio gpio_stby;
-	enum v4l2_mbus_type bus_type;
-	u8 nlanes;
-	u8 horiz_flip;
-	u8 vert_flip;
-};
-
-#endif /* S5K6AA_H */