1
2
3
4
5
6
7
8
9
10
11
12
13
14
15
16
17
18
19
20
21
22
23
24
25
26
27
28
29
30
31
32
33
34
35
36
37
38
39
40
41
42
43
44
45
46
47
48
49
50
51
52
53
54
55
56
57
58
59
60
61
62
63
64
65
66
67
68
69
70
71
72
73
74
75
76
77
78
79
80
81
82
83
84
85
86
87
88
89
90
91
92
93
94
95
96
97
98
99
100
101
102
103
104
105
106
107
108
109
110
111
112
113
114
115
116
117
118
119
120
121
122
123
124
125
126
127
128
129
130
131
132
133
134
135
136
137
138
139
140
141
142
143
144
145
146
147
148
149
150
151
152
153
154
155
156
157
158
159
160
161
162
163
164
165
166
167
168
169
170
171
172
173
174
175
176
177
178
179
180
181
182
183
184
185
186
187
188
189
190
191
192
193
194
195
196
197
198
199
200
201
|
# SPDX-License-Identifier: (GPL-2.0-only OR BSD-2-Clause)
%YAML 1.2
---
$id: http://devicetree.org/schemas/pci/fsl,imx6q-pcie.yaml#
$schema: http://devicetree.org/meta-schemas/core.yaml#
title: Freescale i.MX6 PCIe host controller
maintainers:
- Lucas Stach <l.stach@pengutronix.de>
- Richard Zhu <hongxing.zhu@nxp.com>
description: |+
This PCIe host controller is based on the Synopsys DesignWare PCIe IP
and thus inherits all the common properties defined in snps,dw-pcie.yaml.
allOf:
- $ref: /schemas/pci/snps,dw-pcie.yaml#
properties:
compatible:
enum:
- fsl,imx6q-pcie
- fsl,imx6sx-pcie
- fsl,imx6qp-pcie
- fsl,imx7d-pcie
- fsl,imx8mq-pcie
reg:
items:
- description: Data Bus Interface (DBI) registers.
- description: PCIe configuration space region.
reg-names:
items:
- const: dbi
- const: config
interrupts:
items:
- description: builtin MSI controller.
interrupt-names:
items:
- const: msi
clocks:
minItems: 3
items:
- description: PCIe bridge clock.
- description: PCIe bus clock.
- description: PCIe PHY clock.
- description: Additional required clock entry for imx6sx-pcie,
imx8mq-pcie.
clock-names:
minItems: 3
items:
- const: pcie
- const: pcie_bus
- const: pcie_phy
- const: pcie_inbound_axi for imx6sx-pcie, pcie_aux for imx8mq-pcie
num-lanes:
const: 1
fsl,imx7d-pcie-phy:
$ref: /schemas/types.yaml#/definitions/phandle
description: A phandle to an fsl,imx7d-pcie-phy node. Additional
required properties for imx7d-pcie and imx8mq-pcie.
power-domains:
items:
- description: The phandle pointing to the DISPLAY domain for
imx6sx-pcie, to PCIE_PHY power domain for imx7d-pcie and
imx8mq-pcie.
- description: The phandle pointing to the PCIE_PHY power domains
for imx6sx-pcie.
power-domain-names:
items:
- const: pcie
- const: pcie_phy
resets:
maxItems: 3
description: Phandles to PCIe-related reset lines exposed by SRC
IP block. Additional required by imx7d-pcie and imx8mq-pcie.
reset-names:
items:
- const: pciephy
- const: apps
- const: turnoff
fsl,tx-deemph-gen1:
description: Gen1 De-emphasis value (optional required).
$ref: /schemas/types.yaml#/definitions/uint32
default: 0
fsl,tx-deemph-gen2-3p5db:
description: Gen2 (3.5db) De-emphasis value (optional required).
$ref: /schemas/types.yaml#/definitions/uint32
default: 0
fsl,tx-deemph-gen2-6db:
description: Gen2 (6db) De-emphasis value (optional required).
$ref: /schemas/types.yaml#/definitions/uint32
default: 20
fsl,tx-swing-full:
description: Gen2 TX SWING FULL value (optional required).
$ref: /schemas/types.yaml#/definitions/uint32
default: 127
fsl,tx-swing-low:
description: TX launch amplitude swing_low value (optional required).
$ref: /schemas/types.yaml#/definitions/uint32
default: 127
fsl,max-link-speed:
description: Specify PCI Gen for link capability (optional required).
Note that the IMX6 LVDS clock outputs do not meet gen2 jitter
requirements and thus for gen2 capability a gen2 compliant clock
generator should be used and configured.
$ref: /schemas/types.yaml#/definitions/uint32
enum: [1, 2, 3, 4]
default: 1
reset-gpio:
description: Should specify the GPIO for controlling the PCI bus device
reset signal. It's not polarity aware and defaults to active-low reset
sequence (L=reset state, H=operation state) (optional required).
reset-gpio-active-high:
description: If present then the reset sequence using the GPIO
specified in the "reset-gpio" property is reversed (H=reset state,
L=operation state) (optional required).
vpcie-supply:
description: Should specify the regulator in charge of PCIe port power.
The regulator will be enabled when initializing the PCIe host and
disabled either as part of the init process or when shutting down
the host (optional required).
vph-supply:
description: Should specify the regulator in charge of VPH one of
the three PCIe PHY powers. This regulator can be supplied by both
1.8v and 3.3v voltage supplies (optional required).
required:
- compatible
- reg
- reg-names
- "#address-cells"
- "#size-cells"
- device_type
- bus-range
- ranges
- num-lanes
- interrupts
- interrupt-names
- "#interrupt-cells"
- interrupt-map-mask
- interrupt-map
- clocks
- clock-names
unevaluatedProperties: false
examples:
- |
#include <dt-bindings/clock/imx6qdl-clock.h>
#include <dt-bindings/interrupt-controller/arm-gic.h>
pcie: pcie@1ffc000 {
compatible = "fsl,imx6q-pcie";
reg = <0x01ffc000 0x04000>,
<0x01f00000 0x80000>;
reg-names = "dbi", "config";
#address-cells = <3>;
#size-cells = <2>;
device_type = "pci";
bus-range = <0x00 0xff>;
ranges = <0x81000000 0 0 0x01f80000 0 0x00010000>,
<0x82000000 0 0x01000000 0x01000000 0 0x00f00000>;
num-lanes = <1>;
interrupts = <GIC_SPI 120 IRQ_TYPE_LEVEL_HIGH>;
interrupt-names = "msi";
#interrupt-cells = <1>;
interrupt-map-mask = <0 0 0 0x7>;
interrupt-map = <0 0 0 1 &gpc GIC_SPI 123 IRQ_TYPE_LEVEL_HIGH>,
<0 0 0 2 &gpc GIC_SPI 122 IRQ_TYPE_LEVEL_HIGH>,
<0 0 0 3 &gpc GIC_SPI 121 IRQ_TYPE_LEVEL_HIGH>,
<0 0 0 4 &gpc GIC_SPI 120 IRQ_TYPE_LEVEL_HIGH>;
clocks = <&clks IMX6QDL_CLK_PCIE_AXI>,
<&clks IMX6QDL_CLK_LVDS1_GATE>,
<&clks IMX6QDL_CLK_PCIE_REF_125M>;
clock-names = "pcie", "pcie_bus", "pcie_phy";
};
...
|
