| Age | Commit message (Collapse) | Author | Files | Lines |
|---|
|
Most flexcan IP cores support 2 RX modes:
- FIFO
- mailbox
The flexcan IP core on the MCF5441X cannot receive CAN RTR messages
via mailboxes. However the mailbox mode is more performant. The commit
| 1c45f5778a3b ("can: flexcan: add ethtool support to change rx-rtr setting during runtime")
added support to switch from FIFO to mailbox mode on these cores.
After testing the mailbox mode on the MCF5441X by Angelo Dureghello,
this patch marks it (without RTR capability) as supported. Further the
IP core overview table is updated, that RTR reception via mailboxes is
not supported.
Link: https://lore.kernel.org/all/20220121084425.3141218-1-mkl@pengutronix.de
Tested-by: Angelo Dureghello <angelo@kernel-space.org>
Signed-off-by: Marc Kleine-Budde <mkl@pengutronix.de>
|
|
The MRAM of the tcan4x5x has a size of 2K and starts at 0x8000. There
are no further registers in the tcan4x5x making 0x87fc the biggest
addressable register.
This patch fixes the max register value of the regmap config from
0x8ffc to 0x87fc.
Fixes: 6e1caaf8ed22 ("can: tcan4x5x: fix max register value")
Link: https://lore.kernel.org/all/20220119064011.2943292-1-mkl@pengutronix.de
Signed-off-by: Marc Kleine-Budde <mkl@pengutronix.de>
|
|
length is 0
In order to optimize FIFO access, especially on m_can cores attached
to slow busses like SPI, in patch
| e39381770ec9 ("can: m_can: Disable IRQs on FIFO bus errors")
bulk read/write support has been added to the m_can_fifo_{read,write}
functions.
That change leads to the tcan driver to call
regmap_bulk_{read,write}() with a length of 0 (for CAN frames with 0
data length). regmap treats this as an error:
| tcan4x5x spi1.0 tcan4x5x0: FIFO write returned -22
This patch fixes the problem by not calling the
cdev->ops->{read,write)_fifo() in case of a 0 length read/write.
Fixes: e39381770ec9 ("can: m_can: Disable IRQs on FIFO bus errors")
Link: https://lore.kernel.org/all/20220114155751.2651888-1-mkl@pengutronix.de
Cc: stable@vger.kernel.org
Cc: Matt Kline <matt@bitbashing.io>
Cc: Chandrasekar Ramakrishnan <rcsekar@samsung.com>
Reported-by: Michael Anochin <anochin@photo-meter.com>
Signed-off-by: Marc Kleine-Budde <mkl@pengutronix.de>
|
|
git://git.kernel.org/pub/scm/linux/kernel/git/gregkh/tty
Pull tty/serial driver updates from Greg KH:
"Here is the big set of tty/serial driver updates for 5.17-rc1.
Nothing major in here, just lots of good updates and fixes, including:
- more tty core cleanups from Jiri as well as mxser driver cleanups.
This is the majority of the core diffstat
- tty documentation updates from Jiri
- platform_get_irq() updates
- various serial driver updates for new features and hardware
- fifo usage for 8250 console, reducing cpu load a lot
- LED fix for keyboards, long-time bugfix that went through many
revisions
- minor cleanups
All have been in linux-next for a while with no reported problems"
* tag 'tty-5.17-rc1' of git://git.kernel.org/pub/scm/linux/kernel/git/gregkh/tty: (119 commits)
serial: core: Keep mctrl register state and cached copy in sync
serial: stm32: correct loop for dma error handling
serial: stm32: fix flow control transfer in DMA mode
serial: stm32: rework TX DMA state condition
serial: stm32: move tx dma terminate DMA to shutdown
serial: pl011: Drop redundant DTR/RTS preservation on close/open
serial: pl011: Drop CR register reset on set_termios
serial: pl010: Drop CR register reset on set_termios
serial: liteuart: fix MODULE_ALIAS
serial: 8250_bcm7271: Fix return error code in case of dma_alloc_coherent() failure
Revert "serdev: BREAK/FRAME/PARITY/OVERRUN notification prototype V2"
tty: goldfish: Use platform_get_irq() to get the interrupt
serdev: BREAK/FRAME/PARITY/OVERRUN notification prototype V2
tty: serial: meson: Drop the legacy compatible strings and clock code
serial: pmac_zilog: Use platform_get_irq() to get the interrupt
serial: bcm63xx: Use platform_get_irq() to get the interrupt
serial: ar933x: Use platform_get_irq() to get the interrupt
serial: vt8500: Use platform_get_irq() to get the interrupt
serial: altera_jtaguart: Use platform_get_irq_optional() to get the interrupt
serial: pxa: Use platform_get_irq() to get the interrupt
...
|
|
Merge in fixes directly in prep for the 5.17 merge window.
No conflicts.
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
|
|
No information is deliberately sent in hf->flags in host -> device
communications, but the open-source candleLight firmware echoes it
back, which can result in the GS_CAN_FLAG_OVERFLOW flag being set and
generating spurious ERRORFRAMEs.
While there also initialize the reserved member with 0.
Fixes: d08e973a77d1 ("can: gs_usb: Added support for the GS_USB CAN devices")
Link: https://lore.kernel.org/all/20220106002952.25883-1-brian.silverman@bluerivertech.com
Link: https://github.com/candle-usb/candleLight_fw/issues/87
Cc: stable@vger.kernel.org
Signed-off-by: Brian Silverman <brian.silverman@bluerivertech.com>
[mkl: initialize the reserved member, too]
Signed-off-by: Marc Kleine-Budde <mkl@pengutronix.de>
|
|
device
Make sure we free CAN network device in the error path. There are
several jumps to fail label after allocating the CAN network device
successfully. This patch places the free_candev() under fail label so
that in failure path a jump to fail label frees the CAN network
device.
Fixes: 76e9353a80e9 ("can: rcar_canfd: Add support for RZ/G2L family")
Link: https://lore.kernel.org/all/20220106114801.20563-1-prabhakar.mahadev-lad.rj@bp.renesas.com
Reported-by: Pavel Machek <pavel@denx.de>
Signed-off-by: Lad Prabhakar <prabhakar.mahadev-lad.rj@bp.renesas.com>
Reviewed-by: Kieran Bingham <kieran.bingham+renesas@ideasonboard.com>
Signed-off-by: Marc Kleine-Budde <mkl@pengutronix.de>
|
|
For the possible failure of the platform_get_irq(), the returned irq
could be error number and will finally cause the failure of the
request_irq().
Consider that platform_get_irq() can now in certain cases return
-EPROBE_DEFER, and the consequences of letting request_irq()
effectively convert that into -EINVAL, even at probe time rather than
later on. So it might be better to check just now.
Fixes: b1201e44f50b ("can: xilinx CAN controller support")
Link: https://lore.kernel.org/all/20211224021324.1447494-1-jiasheng@iscas.ac.cn
Signed-off-by: Jiasheng Jiang <jiasheng@iscas.ac.cn>
Signed-off-by: Marc Kleine-Budde <mkl@pengutronix.de>
|
|
In the function softing_startstop() the variable error_reporting is
assigned but not used. The code that uses this variable is commented
out. Its stated that the functionality is not finally verified.
To fix the warning:
| drivers/net/can/softing/softing_fw.c:424:9: error: variable 'error_reporting' set but not used [-Werror,-Wunused-but-set-variable]
remove the comment, activate the code, but add a "0 &&" to the if
expression and rely on the optimizer rather than the preprocessor to
remove the code.
Link: https://lore.kernel.org/all/20220109103126.1872833-1-mkl@pengutronix.de
Fixes: 03fd3cf5a179 ("can: add driver for Softing card")
Cc: Kurt Van Dijck <dev.kurt@vandijck-laurijssen.be>
Signed-off-by: Marc Kleine-Budde <mkl@pengutronix.de>
|
|
In case device registration fails during probe, the driver state and
the embedded platform device structure needs to be freed using
platform_device_put() to properly free all resources (e.g. the device
name).
Fixes: 0a0b7a5f7a04 ("can: add driver for Softing card")
Link: https://lore.kernel.org/all/20211222104843.6105-1-johan@kernel.org
Cc: stable@vger.kernel.org # 2.6.38
Signed-off-by: Johan Hovold <johan@kernel.org>
Reviewed-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Signed-off-by: Marc Kleine-Budde <mkl@pengutronix.de>
|
|
This patch adds ethtool support to get the number of message buffers
configured for reception/transmission, which may also depends on
runtime configurations such as the 'rx-rtr' flag state.
Link: https://lore.kernel.org/all/20220108181633.420433-1-dario.binacchi@amarulasolutions.com
Signed-off-by: Dario Binacchi <dario.binacchi@amarulasolutions.com>
[mkl: port to net-next/master, replace __sw_hweight64 by simpler calculation]
Signed-off-by: Marc Kleine-Budde <mkl@pengutronix.de>
|
|
This patch adds a private flag to the flexcan driver to switch the
"rx-rtr" setting on and off.
"rx-rtr" on - Receive RTR frames. (default)
The CAN controller can and will receive RTR frames.
On some IP cores the controller cannot receive RTR
frames in the more performant "RX mailbox" mode and
will use "RX FIFO" mode instead.
"rx-rtr" off - Waive ability to receive RTR frames. (not supported on all IP cores)
This mode activates the "RX mailbox mode" for better
performance, on some IP cores RTR frames cannot be
received anymore.
The "RX FIFO" mode uses a FIFO with a depth of 6 CAN frames.
The "RX mailbox" mode uses up to 62 mailboxes.
Link: https://lore.kernel.org/all/20220107193105.1699523-6-mkl@pengutronix.de
Signed-off-by: Dario Binacchi <dario.binacchi@amarulasolutions.com>
Co-developed-by: Dario Binacchi <dario.binacchi@amarulasolutions.com>
Signed-off-by: Marc Kleine-Budde <mkl@pengutronix.de>
|
|
Most flexcan IP cores support 2 RX modes:
- FIFO
- mailbox
Some IP core versions cannot receive CAN RTR messages via mailboxes.
This patch adds quirks to document this.
This information will be used in a later patch to switch from FIFO to
more performant mailbox mode at the expense of losing the ability to
receive RTR messages. This trade off is beneficial in certain use
cases.
Link: https://lore.kernel.org/all/20220107193105.1699523-5-mkl@pengutronix.de
Signed-off-by: Marc Kleine-Budde <mkl@pengutronix.de>
|
|
Most flexcan IP cores support 2 RX modes:
- FIFO
- mailbox
The names for these modes were chosen to reflect the name of the
rx-offload mode they are using.
The name of the RX modes should better reflect their difference with
regards the flexcan IP core. So this patch renames the various
occurrences of OFF_FIFO to RX_FIFO and OFF_TIMESTAMP to RX_MAILBOX:
| FLEXCAN_TX_MB_RESERVED_OFF_FIFO -> FLEXCAN_TX_MB_RESERVED_RX_FIFO
| FLEXCAN_TX_MB_RESERVED_OFF_TIMESTAMP -> FLEXCAN_TX_MB_RESERVED_RX_MAILBOX
| FLEXCAN_QUIRK_USE_OFF_TIMESTAMP -> FLEXCAN_QUIRK_USE_RX_MAILBOX
Link: https://lore.kernel.org/all/20220107193105.1699523-4-mkl@pengutronix.de
Signed-off-by: Marc Kleine-Budde <mkl@pengutronix.de>
|
|
This is a preparation patch for the upcoming support to change the
rx-rtr capability via the ethtool API.
Link: https://lore.kernel.org/all/20220107193105.1699523-3-mkl@pengutronix.de
Signed-off-by: Dario Binacchi <dario.binacchi@amarulasolutions.com>
Signed-off-by: Marc Kleine-Budde <mkl@pengutronix.de>
|
|
This patch moves the flexcan driver into a separate directory, a later
patch will add more files.
Link: https://lore.kernel.org/all/20220107193105.1699523-2-mkl@pengutronix.de
Signed-off-by: Marc Kleine-Budde <mkl@pengutronix.de>
|
|
This patch replaces the open coded check, if the chip's FIFOs are
configured for CAN-FD mode, by the newly introduced function
mcp251xfd_is_fd_mode().
Link: https://lore.kernel.org/all/20220105154300.1258636-14-mkl@pengutronix.de
Signed-off-by: Marc Kleine-Budde <mkl@pengutronix.de>
|
|
This patch moves the ring initialization from the mcp251xfd core file
into a separate one to make the driver a bit more orderly.
Link: https://lore.kernel.org/all/20220105154300.1258636-13-mkl@pengutronix.de
Signed-off-by: Marc Kleine-Budde <mkl@pengutronix.de>
|
|
This patch moves the chip FIFO initialization from the mcp251xfd core
file into a separate one to make the driver a bit more orderly.
Link: https://lore.kernel.org/all/20220105154300.1258636-12-mkl@pengutronix.de
Signed-off-by: Marc Kleine-Budde <mkl@pengutronix.de>
|
|
This patch moves the TEF handling from the mcp251xfd core file into a
separate one to make the driver a bit more orderly.
Link: https://lore.kernel.org/all/20220105154300.1258636-11-mkl@pengutronix.de
Signed-off-by: Marc Kleine-Budde <mkl@pengutronix.de>
|
|
This patch moves the TX handling from the mcp251xfd core file into a
separate one to make the driver a bit more orderly.
Link: https://lore.kernel.org/all/20220105154300.1258636-10-mkl@pengutronix.de
Signed-off-by: Marc Kleine-Budde <mkl@pengutronix.de>
|
|
This patch moves the RX handling from the mcp251xfd core file into a
separate one to make the driver a bit more orderly.
Link: https://lore.kernel.org/all/20220105154300.1258636-9-mkl@pengutronix.de
Signed-off-by: Marc Kleine-Budde <mkl@pengutronix.de>
|
|
The .c files in the Makefile are ordered alphabetically. This patch
groups the function prototypes by their corresponding .c file and
brings the into the same order.
Link: https://lore.kernel.org/all/20220105154300.1258636-8-mkl@pengutronix.de
Signed-off-by: Marc Kleine-Budde <mkl@pengutronix.de>
|
|
debug + add rate limiting
A RX overflow usually happens during high system load. Printing
overflow messages to the kernel log, which on embedded systems often
is outputted on the serial console, even increases the system load.
To decrease the system load in these situations, denote the messages
to debug level and wrap them with net_ratelimit().
Link: https://lore.kernel.org/all/20220105154300.1258636-7-mkl@pengutronix.de
Signed-off-by: Marc Kleine-Budde <mkl@pengutronix.de>
|
|
With patch
| dd8088d5a896 PM: runtime: Add pm_runtime_resume_and_get to deal with usage counter
the usual pm_runtime_get_sync() and pm_runtime_put_noidle()
in-case-of-error dance is no longer needed. Convert the mcp251xfd
driver to use this function.
Link: https://lore.kernel.org/all/20220105154300.1258636-6-mkl@pengutronix.de
Signed-off-by: Marc Kleine-Budde <mkl@pengutronix.de>
|
|
This patch exchanges the order of open_candev() and
pm_runtime_get_sync(), so that open_candev() is called first.
A usual reason why open_candev() fails is missing CAN bit rate
configuration. It makes no sense to resume the device from PM sleep
first just to put it to sleep if the bit rate is not configured.
Link: https://lore.kernel.org/all/20220105154300.1258636-5-mkl@pengutronix.de
Signed-off-by: Marc Kleine-Budde <mkl@pengutronix.de>
|
|
This patch adds the missing newline to printed strings.
Fixes: 55e5b97f003e ("can: mcp25xxfd: add driver for Microchip MCP25xxFD SPI CAN")
Link: https://lore.kernel.org/all/20220105154300.1258636-4-mkl@pengutronix.de
Signed-off-by: Marc Kleine-Budde <mkl@pengutronix.de>
|
|
This patch fixes a typo in the error message in
mcp251xfd_tef_obj_read(), if trying to read too many objects.
Link: https://lore.kernel.org/all/20220105154300.1258636-3-mkl@pengutronix.de
Fixes: 55e5b97f003e ("can: mcp25xxfd: add driver for Microchip MCP25xxFD SPI CAN")
Signed-off-by: Marc Kleine-Budde <mkl@pengutronix.de>
|
|
This patch removes double blank lines from the driver.
Link: https://lore.kernel.org/all/20220105154300.1258636-2-mkl@pengutronix.de
Signed-off-by: Marc Kleine-Budde <mkl@pengutronix.de>
|
|
Clang static analysis reports this problem
janz-ican3.c:1311:2: warning: Undefined or garbage value returned to caller
return dlc;
^~~~~~~~~~
dlc is only set with this conditional
if (!(cf->can_id & CAN_RTR_FLAG))
dlc = cf->len;
But is always returned. So initialize dlc to 0.
Fixes: cc4b08c31b5c ("can: do not increase tx_bytes statistics for RTR frames")
Link: https://lore.kernel.org/all/20220108143319.3986923-1-trix@redhat.com
Signed-off-by: Tom Rix <trix@redhat.com>
Acked-by: Vincent Mailhol <mailhol.vincent@wanadoo.fr>
Signed-off-by: Marc Kleine-Budde <mkl@pengutronix.de>
|
|
of invalid USB data
The received data contains the channel the received data is associated
with. If the channel number is bigger than the actual number of
channels assume broken or malicious USB device and shut it down.
This fixes the error found by clang:
| drivers/net/can/usb/gs_usb.c:386:6: error: variable 'dev' is used
| uninitialized whenever 'if' condition is true
| if (hf->channel >= GS_MAX_INTF)
| ^~~~~~~~~~~~~~~~~~~~~~~~~~
| drivers/net/can/usb/gs_usb.c:474:10: note: uninitialized use occurs here
| hf, dev->gs_hf_size, gs_usb_receive_bulk_callback,
| ^~~
Link: https://lore.kernel.org/all/20211210091158.408326-1-mkl@pengutronix.de
Fixes: d08e973a77d1 ("can: gs_usb: Added support for the GS_USB CAN devices")
Cc: stable@vger.kernel.org
Signed-off-by: Marc Kleine-Budde <mkl@pengutronix.de>
|
|
Currently, the CAN netlink interface provides no easy ways to check
the capabilities of a given controller. The only method from the
command line is to try each CAN_CTRLMODE_* individually to check
whether the netlink interface returns an -EOPNOTSUPP error or not
(alternatively, one may find it easier to directly check the source
code of the driver instead...)
This patch introduces a method for the user to check both the
supported and the static capabilities. The proposed method introduces
a new IFLA nest: IFLA_CAN_CTRLMODE_EXT which extends the current
IFLA_CAN_CTRLMODE. This is done to guaranty a full forward and
backward compatibility between the kernel and the user land
applications.
The IFLA_CAN_CTRLMODE_EXT nest contains one single entry:
IFLA_CAN_CTRLMODE_SUPPORTED. Because this entry is only used in one
direction: kernel to userland, no new struct nla_policy are
introduced.
Below table explains how IFLA_CAN_CTRLMODE_SUPPORTED (hereafter:
"supported") and can_ctrlmode::flags (hereafter: "flags") allow us to
identify both the supported and the static capabilities, when masked
with any of the CAN_CTRLMODE_* bit flags:
supported & flags & Controller capabilities
CAN_CTRLMODE_* CAN_CTRLMODE_*
-----------------------------------------------------------------------
false false Feature not supported (always disabled)
false true Static feature (always enabled)
true false Feature supported but disabled
true true Feature supported and enabled
Link: https://lore.kernel.org/all/20211213160226.56219-5-mailhol.vincent@wanadoo.fr
Signed-off-by: Vincent Mailhol <mailhol.vincent@wanadoo.fr>
Signed-off-by: Marc Kleine-Budde <mkl@pengutronix.de>
|
|
Previous patch removed can_priv::ctrlmode_static to replace it with
can_get_static_ctrlmode().
A condition sine qua non for this to work is that the controller
static modes should never be set in can_priv::ctrlmode_supported
(c.f. the comment on can_priv::ctrlmode_supported which states that it
is for "options that can be *modified* by netlink"). Also, this
condition is already correctly fulfilled by all existing drivers
which rely on the ctrlmode_static feature.
Nonetheless, we added an extra safeguard in can_set_static_ctrlmode()
to return an error value and to warn the developer who would be
adventurous enough to set to static a given feature that is already
set to supported.
The drivers which rely on the static controller mode are then updated
to check the return value of can_set_static_ctrlmode().
Link: https://lore.kernel.org/all/20211213160226.56219-3-mailhol.vincent@wanadoo.fr
Signed-off-by: Vincent Mailhol <mailhol.vincent@wanadoo.fr>
Signed-off-by: Marc Kleine-Budde <mkl@pengutronix.de>
|
|
The statically enabled features of a CAN controller can be retrieved
using below formula:
| u32 ctrlmode_static = priv->ctrlmode & ~priv->ctrlmode_supported;
As such, there is no need to store this information. This patch remove
the field ctrlmode_static of struct can_priv and provides, in
replacement, the inline function can_get_static_ctrlmode() which
returns the same value.
Link: https://lore.kernel.org/all/20211213160226.56219-2-mailhol.vincent@wanadoo.fr
Signed-off-by: Vincent Mailhol <mailhol.vincent@wanadoo.fr>
Signed-off-by: Marc Kleine-Budde <mkl@pengutronix.de>
|
|
The actual payload length of the CAN Remote Transmission Request (RTR)
frames is always 0, i.e. no payload is transmitted on the wire.
However, those RTR frames still use the DLC to indicate the length of
the requested frame.
As such, net_device_stats::tx_bytes should not be increased when
sending RTR frames.
The function can_get_echo_skb() already returns the correct length,
even for RTR frames (c.f. [1]). However, for historical reasons, the
drivers do not use can_get_echo_skb()'s return value and instead, most
of them store a temporary length (or dlc) in some local structure or
array. Using the return value of can_get_echo_skb() solves the
issue. After doing this, such length/dlc fields become unused and so
this patch does the adequate cleaning when needed.
This patch fixes all the CAN drivers.
Finally, can_get_echo_skb() is decorated with the __must_check
attribute in order to force future drivers to correctly use its return
value (else the compiler would emit a warning).
[1] commit ed3320cec279 ("can: dev: __can_get_echo_skb():
fix real payload length return value for RTR frames")
Link: https://lore.kernel.org/all/20211207121531.42941-6-mailhol.vincent@wanadoo.fr
Cc: Nicolas Ferre <nicolas.ferre@microchip.com>
Cc: Alexandre Belloni <alexandre.belloni@bootlin.com>
Cc: Ludovic Desroches <ludovic.desroches@microchip.com>
Cc: Maxime Ripard <mripard@kernel.org>
Cc: Chen-Yu Tsai <wens@csie.org>
Cc: Jernej Skrabec <jernej.skrabec@gmail.com>
Cc: Yasushi SHOJI <yashi@spacecubics.com>
Cc: Oliver Hartkopp <socketcan@hartkopp.net>
Cc: Stephane Grosjean <s.grosjean@peak-system.com>
Cc: Andreas Larsson <andreas@gaisler.com>
Tested-by: Jimmy Assarsson <extja@kvaser.com> # kvaser
Signed-off-by: Vincent Mailhol <mailhol.vincent@wanadoo.fr>
Acked-by: Stefan Mätje <stefan.maetje@esd.eu> # esd_usb2
Tested-by: Stefan Mätje <stefan.maetje@esd.eu> # esd_usb2
[mkl: add conversion for grcan]
Signed-off-by: Marc Kleine-Budde <mkl@pengutronix.de>
|
|
The actual payload length of the CAN Remote Transmission Request (RTR)
frames is always 0, i.e. no payload is transmitted on the wire.
However, those RTR frames still use the DLC to indicate the length of
the requested frame.
As such, net_device_stats::rx_bytes should not be increased for the
RTR frames.
This patch fixes all the CAN drivers.
Link: https://lore.kernel.org/all/20211207121531.42941-5-mailhol.vincent@wanadoo.fr
Cc: Marc Kleine-Budde <mkl@pengutronix.de>
Cc: Nicolas Ferre <nicolas.ferre@microchip.com>
Cc: Alexandre Belloni <alexandre.belloni@bootlin.com>
Cc: Ludovic Desroches <ludovic.desroches@microchip.com>
Cc: Chandrasekar Ramakrishnan <rcsekar@samsung.com>
Cc: Maxime Ripard <mripard@kernel.org>
Cc: Chen-Yu Tsai <wens@csie.org>
Cc: Jernej Skrabec <jernej.skrabec@gmail.com>
Cc: Yasushi SHOJI <yashi@spacecubics.com>
Cc: Appana Durga Kedareswara rao <appana.durga.rao@xilinx.com>
Cc: Naga Sureshkumar Relli <naga.sureshkumar.relli@xilinx.com>
Cc: Michal Simek <michal.simek@xilinx.com>
Cc: Stephane Grosjean <s.grosjean@peak-system.com>
Tested-by: Jimmy Assarsson <extja@kvaser.com> # kvaser
Signed-off-by: Vincent Mailhol <mailhol.vincent@wanadoo.fr>
Acked-by: Stefan Mätje <stefan.maetje@esd.eu> # esd_usb2
Tested-by: Stefan Mätje <stefan.maetje@esd.eu> # esd_usb2
Signed-off-by: Marc Kleine-Budde <mkl@pengutronix.de>
|
|
The actual payload length of the CAN Remote Transmission Request (RTR)
frames is always 0, i.e. no payload is transmitted on the wire.
However, those RTR frames still use the DLC to indicate the length of
the requested frame.
For this reason, it is incorrect to copy the payload of RTR frames
(the payload buffer would only contain garbage data). This patch
encapsulates the payload copy in a check toward the RTR flag.
Link: https://lore.kernel.org/all/20211207121531.42941-4-mailhol.vincent@wanadoo.fr
Cc: Yasushi SHOJI <yashi@spacecubics.com>
Tested-by: Yasushi SHOJI <yashi@spacecubics.com>
Signed-off-by: Vincent Mailhol <mailhol.vincent@wanadoo.fr>
Signed-off-by: Marc Kleine-Budde <mkl@pengutronix.de>
|
|
The CAN error message frames (i.e. error skb) are an interface
specific to socket CAN. The payload of the CAN error message frames
does not correspond to any actual data sent on the wire. Only an error
flag and a delimiter are transmitted when an error occurs (c.f. ISO
11898-1 section 10.4.4.2 "Error flag").
For this reason, it makes no sense to increment the tx_packets and
tx_bytes fields of struct net_device_stats when sending an error
message frame because no actual payload will be transmitted on the
wire.
N.B. Sending error message frames is a very specific feature which, at
the moment, is only supported by the Kvaser Hydra hardware. Please
refer to [1] for more details on the topic.
[1] https://lore.kernel.org/linux-can/CAMZ6RqK0rTNg3u3mBpZOoY51jLZ-et-J01tY6-+mWsM4meVw-A@mail.gmail.com/t/#u
Link: https://lore.kernel.org/all/20211207121531.42941-3-mailhol.vincent@wanadoo.fr
Co-developed-by: Jimmy Assarsson <extja@kvaser.com>
Signed-off-by: Jimmy Assarsson <extja@kvaser.com>
Signed-off-by: Vincent Mailhol <mailhol.vincent@wanadoo.fr>
Signed-off-by: Marc Kleine-Budde <mkl@pengutronix.de>
|
|
The CAN error message frames (i.e. error skb) are an interface
specific to socket CAN. The payload of the CAN error message frames
does not correspond to any actual data sent on the wire. Only an error
flag and a delimiter are transmitted when an error occurs (c.f. ISO
11898-1 section 10.4.4.2 "Error flag").
For this reason, it makes no sense to increment the rx_packets and
rx_bytes fields of struct net_device_stats because no actual payload
were transmitted on the wire.
This patch fixes all the CAN drivers.
Link: https://lore.kernel.org/all/20211207121531.42941-2-mailhol.vincent@wanadoo.fr
CC: Marc Kleine-Budde <mkl@pengutronix.de>
CC: Nicolas Ferre <nicolas.ferre@microchip.com>
CC: Alexandre Belloni <alexandre.belloni@bootlin.com>
CC: Ludovic Desroches <ludovic.desroches@microchip.com>
CC: Chandrasekar Ramakrishnan <rcsekar@samsung.com>
CC: Maxime Ripard <mripard@kernel.org>
CC: Chen-Yu Tsai <wens@csie.org>
CC: Jernej Skrabec <jernej.skrabec@gmail.com>
CC: Appana Durga Kedareswara rao <appana.durga.rao@xilinx.com>
CC: Naga Sureshkumar Relli <naga.sureshkumar.relli@xilinx.com>
CC: Michal Simek <michal.simek@xilinx.com>
CC: Stephane Grosjean <s.grosjean@peak-system.com>
Tested-by: Jimmy Assarsson <extja@kvaser.com> # kvaser
Signed-off-by: Vincent Mailhol <mailhol.vincent@wanadoo.fr>
Acked-by: Stefan Mätje <stefan.maetje@esd.eu> # esd_usb2
Tested-by: Stefan Mätje <stefan.maetje@esd.eu> # esd_usb2
Signed-off-by: Marc Kleine-Budde <mkl@pengutronix.de>
|
|
The field dev_port of struct net_device indicates the port number of a
network device [1]. This patch populates this field.
This field can be helpful to distinguish between the two network
interfaces of a dual channel device (i.e. ES581.4 or ES582.1). Indeed,
at the moment, all the network interfaces of a same device share the
same static udev attributes c.f. output of:
| udevadm info --attribute-walk /sys/class/net/canX
The dev_port attribute can then be used to write some udev rules to,
for example, assign a permanent name to each network interface based
on the serial/dev_port pair (which is convenient when you have a test
bench with several CAN devices connected simultaneously and wish to
keep consistent interface names upon reboot).
[1] https://www.kernel.org/doc/Documentation/ABI/testing/sysfs-class-net
Link: https://lore.kernel.org/all/20211026180553.1953189-1-mailhol.vincent@wanadoo.fr
Suggested-by: Lukas Magel <lukas.magel@escrypt.com>
Signed-off-by: Vincent Mailhol <mailhol.vincent@wanadoo.fr>
Signed-off-by: Marc Kleine-Budde <mkl@pengutronix.de>
|
|
It is preferred that drivers use platform_get_irq() instead of
irq_of_parse_and_map(), so replace.
Link: https://lore.kernel.org/all/20211221200016.13459-1-prabhakar.mahadev-lad.rj@bp.renesas.com
Signed-off-by: Lad Prabhakar <prabhakar.mahadev-lad.rj@bp.renesas.com>
Signed-off-by: Marc Kleine-Budde <mkl@pengutronix.de>
|
|
platform_get_resource(pdev, IORESOURCE_IRQ, ..) relies on static
allocation of IRQ resources in DT core code, this causes an issue when
using hierarchical interrupt domains using "interrupts" property in
the node as this bypasses the hierarchical setup and messes up the irq
chaining.
In preparation for removal of static setup of IRQ resource from DT
core code use platform_get_irq().
Link: https://lore.kernel.org/all/20211221194508.11737-1-prabhakar.mahadev-lad.rj@bp.renesas.com
Signed-off-by: Lad Prabhakar <prabhakar.mahadev-lad.rj@bp.renesas.com>
Signed-off-by: Marc Kleine-Budde <mkl@pengutronix.de>
|
|
Use the MEGA define plus the comment /* Hz */ when assigning
frequencies.
Link: https://lore.kernel.org/all/20211210075803.343841-1-mkl@pengutronix.de
Signed-off-by: Jimmy Assarsson <extja@kvaser.com>
Signed-off-by: Marc Kleine-Budde <mkl@pengutronix.de>
|
|
GPIO library does copy the of_node from the parent device of the GPIO
chip, there is no need to repeat this in the individual drivers.
Remove assignment here.
For the details one may look into the of_gpio_dev_init()
implementation.
Link: https://lore.kernel.org/all/20211202205855.76946-1-andriy.shevchenko@linux.intel.com
Signed-off-by: Andy Shevchenko <andriy.shevchenko@linux.intel.com>
Signed-off-by: Marc Kleine-Budde <mkl@pengutronix.de>
|
|
This patch removes the unused memberecho_skb from the struct
usb_8dev_priv.
Fixes: 0024d8ad1639 ("can: usb_8dev: Add support for USB2CAN interface from 8 devices")
Link: https://lore.kernel.org/all/20220104230753.956520-1-mkl@pengutronix.de
Signed-off-by: Marc Kleine-Budde <mkl@pengutronix.de>
|
|
sock.h is pretty heavily used (5k objects rebuilt on x86 after
it's touched). We can drop the include of filter.h from it and
add a forward declaration of struct sk_filter instead.
This decreases the number of rebuilt objects when bpf.h
is touched from ~5k to ~1k.
There's a lot of missing includes this was masking. Primarily
in networking tho, this time.
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
Signed-off-by: Alexei Starovoitov <ast@kernel.org>
Acked-by: Marc Kleine-Budde <mkl@pengutronix.de>
Acked-by: Florian Fainelli <f.fainelli@gmail.com>
Acked-by: Nikolay Aleksandrov <nikolay@nvidia.com>
Acked-by: Stefano Garzarella <sgarzare@redhat.com>
Link: https://lore.kernel.org/bpf/20211229004913.513372-1-kuba@kernel.org
|
|
We need the tty/serial fixes in here as well.
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
|
|
No conflicts.
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
|
|
The CAN clock frequency is used when calculating the CAN bittiming
parameters. When wrong clock frequency is used, the device may end up
with wrong bittiming parameters, depending on user requested bittiming
parameters.
To avoid this, get the CAN clock frequency from the device. Various
existing Kvaser Leaf products use different CAN clocks.
Fixes: 080f40a6fa28 ("can: kvaser_usb: Add support for Kvaser CAN/USB devices")
Link: https://lore.kernel.org/all/20211208152122.250852-2-extja@kvaser.com
Cc: stable@vger.kernel.org
Signed-off-by: Jimmy Assarsson <extja@kvaser.com>
Signed-off-by: Marc Kleine-Budde <mkl@pengutronix.de>
|
|
stats->{rx,tx}_errors counter
Check the direction bit in the error frame packet (EPACK) to determine
which net_device_stats {rx,tx}_errors counter to increase.
Fixes: 26ad340e582d ("can: kvaser_pciefd: Add driver for Kvaser PCIEcan devices")
Link: https://lore.kernel.org/all/20211208152122.250852-1-extja@kvaser.com
Cc: stable@vger.kernel.org
Signed-off-by: Jimmy Assarsson <extja@kvaser.com>
Signed-off-by: Marc Kleine-Budde <mkl@pengutronix.de>
|
