summaryrefslogtreecommitdiff
path: root/drivers/ide/hpt366.c
diff options
context:
space:
mode:
Diffstat (limited to 'drivers/ide/hpt366.c')
-rw-r--r--drivers/ide/hpt366.c1545
1 files changed, 0 insertions, 1545 deletions
diff --git a/drivers/ide/hpt366.c b/drivers/ide/hpt366.c
deleted file mode 100644
index 50c9a41467c8..000000000000
--- a/drivers/ide/hpt366.c
+++ /dev/null
@@ -1,1545 +0,0 @@
-// SPDX-License-Identifier: GPL-2.0-only
-/*
- * Copyright (C) 1999-2003 Andre Hedrick <andre@linux-ide.org>
- * Portions Copyright (C) 2001 Sun Microsystems, Inc.
- * Portions Copyright (C) 2003 Red Hat Inc
- * Portions Copyright (C) 2007 Bartlomiej Zolnierkiewicz
- * Portions Copyright (C) 2005-2009 MontaVista Software, Inc.
- *
- * Thanks to HighPoint Technologies for their assistance, and hardware.
- * Special Thanks to Jon Burchmore in SanDiego for the deep pockets, his
- * donation of an ABit BP6 mainboard, processor, and memory acellerated
- * development and support.
- *
- *
- * HighPoint has its own drivers (open source except for the RAID part)
- * available from http://www.highpoint-tech.com/USA_new/service_support.htm
- * This may be useful to anyone wanting to work on this driver, however do not
- * trust them too much since the code tends to become less and less meaningful
- * as the time passes... :-/
- *
- * Note that final HPT370 support was done by force extraction of GPL.
- *
- * - add function for getting/setting power status of drive
- * - the HPT370's state machine can get confused. reset it before each dma
- * xfer to prevent that from happening.
- * - reset state engine whenever we get an error.
- * - check for busmaster state at end of dma.
- * - use new highpoint timings.
- * - detect bus speed using highpoint register.
- * - use pll if we don't have a clock table. added a 66MHz table that's
- * just 2x the 33MHz table.
- * - removed turnaround. NOTE: we never want to switch between pll and
- * pci clocks as the chip can glitch in those cases. the highpoint
- * approved workaround slows everything down too much to be useful. in
- * addition, we would have to serialize access to each chip.
- * Adrian Sun <a.sun@sun.com>
- *
- * add drive timings for 66MHz PCI bus,
- * fix ATA Cable signal detection, fix incorrect /proc info
- * add /proc display for per-drive PIO/DMA/UDMA mode and
- * per-channel ATA-33/66 Cable detect.
- * Duncan Laurie <void@sun.com>
- *
- * fixup /proc output for multiple controllers
- * Tim Hockin <thockin@sun.com>
- *
- * On hpt366:
- * Reset the hpt366 on error, reset on dma
- * Fix disabling Fast Interrupt hpt366.
- * Mike Waychison <crlf@sun.com>
- *
- * Added support for 372N clocking and clock switching. The 372N needs
- * different clocks on read/write. This requires overloading rw_disk and
- * other deeply crazy things. Thanks to <http://www.hoerstreich.de> for
- * keeping me sane.
- * Alan Cox <alan@lxorguk.ukuu.org.uk>
- *
- * - fix the clock turnaround code: it was writing to the wrong ports when
- * called for the secondary channel, caching the current clock mode per-
- * channel caused the cached register value to get out of sync with the
- * actual one, the channels weren't serialized, the turnaround shouldn't
- * be done on 66 MHz PCI bus
- * - disable UltraATA/100 for HPT370 by default as the 33 MHz clock being used
- * does not allow for this speed anyway
- * - avoid touching disabled channels (e.g. HPT371/N are single channel chips,
- * their primary channel is kind of virtual, it isn't tied to any pins)
- * - fix/remove bad/unused timing tables and use one set of tables for the whole
- * HPT37x chip family; save space by introducing the separate transfer mode
- * table in which the mode lookup is done
- * - use f_CNT value saved by the HighPoint BIOS as reading it directly gives
- * the wrong PCI frequency since DPLL has already been calibrated by BIOS;
- * read it only from the function 0 of HPT374 chips
- * - fix the hotswap code: it caused RESET- to glitch when tristating the bus,
- * and for HPT36x the obsolete HDIO_TRISTATE_HWIF handler was called instead
- * - pass to init_chipset() handlers a copy of the IDE PCI device structure as
- * they tamper with its fields
- * - pass to the init_setup handlers a copy of the ide_pci_device_t structure
- * since they may tamper with its fields
- * - prefix the driver startup messages with the real chip name
- * - claim the extra 240 bytes of I/O space for all chips
- * - optimize the UltraDMA filtering and the drive list lookup code
- * - use pci_get_slot() to get to the function 1 of HPT36x/374
- * - cache offset of the channel's misc. control registers (MCRs) being used
- * throughout the driver
- * - only touch the relevant MCR when detecting the cable type on HPT374's
- * function 1
- * - rename all the register related variables consistently
- * - move all the interrupt twiddling code from the speedproc handlers into
- * init_hwif_hpt366(), also grouping all the DMA related code together there
- * - merge HPT36x/HPT37x speedproc handlers, fix PIO timing register mask and
- * separate the UltraDMA and MWDMA masks there to avoid changing PIO timings
- * when setting an UltraDMA mode
- * - fix hpt3xx_tune_drive() to set the PIO mode requested, not always select
- * the best possible one
- * - clean up DMA timeout handling for HPT370
- * - switch to using the enumeration type to differ between the numerous chip
- * variants, matching PCI device/revision ID with the chip type early, at the
- * init_setup stage
- * - extend the hpt_info structure to hold the DPLL and PCI clock frequencies,
- * stop duplicating it for each channel by storing the pointer in the pci_dev
- * structure: first, at the init_setup stage, point it to a static "template"
- * with only the chip type and its specific base DPLL frequency, the highest
- * UltraDMA mode, and the chip settings table pointer filled, then, at the
- * init_chipset stage, allocate per-chip instance and fill it with the rest
- * of the necessary information
- * - get rid of the constant thresholds in the HPT37x PCI clock detection code,
- * switch to calculating PCI clock frequency based on the chip's base DPLL
- * frequency
- * - switch to using the DPLL clock and enable UltraATA/133 mode by default on
- * anything newer than HPT370/A (except HPT374 that is not capable of this
- * mode according to the manual)
- * - fold PCI clock detection and DPLL setup code into init_chipset_hpt366(),
- * also fixing the interchanged 25/40 MHz PCI clock cases for HPT36x chips;
- * unify HPT36x/37x timing setup code and the speedproc handlers by joining
- * the register setting lists into the table indexed by the clock selected
- * - set the correct hwif->ultra_mask for each individual chip
- * - add Ultra and MW DMA mode filtering for the HPT37[24] based SATA cards
- * - stop resetting HPT370's state machine before each DMA transfer as that has
- * caused more harm than good
- * Sergei Shtylyov, <sshtylyov@ru.mvista.com> or <source@mvista.com>
- */
-
-#include <linux/types.h>
-#include <linux/module.h>
-#include <linux/kernel.h>
-#include <linux/delay.h>
-#include <linux/blkdev.h>
-#include <linux/interrupt.h>
-#include <linux/pci.h>
-#include <linux/init.h>
-#include <linux/ide.h>
-#include <linux/slab.h>
-
-#include <linux/uaccess.h>
-#include <asm/io.h>
-
-#define DRV_NAME "hpt366"
-
-/* various tuning parameters */
-#undef HPT_RESET_STATE_ENGINE
-#undef HPT_DELAY_INTERRUPT
-
-static const char *bad_ata100_5[] = {
- "IBM-DTLA-307075",
- "IBM-DTLA-307060",
- "IBM-DTLA-307045",
- "IBM-DTLA-307030",
- "IBM-DTLA-307020",
- "IBM-DTLA-307015",
- "IBM-DTLA-305040",
- "IBM-DTLA-305030",
- "IBM-DTLA-305020",
- "IC35L010AVER07-0",
- "IC35L020AVER07-0",
- "IC35L030AVER07-0",
- "IC35L040AVER07-0",
- "IC35L060AVER07-0",
- "WDC AC310200R",
- NULL
-};
-
-static const char *bad_ata66_4[] = {
- "IBM-DTLA-307075",
- "IBM-DTLA-307060",
- "IBM-DTLA-307045",
- "IBM-DTLA-307030",
- "IBM-DTLA-307020",
- "IBM-DTLA-307015",
- "IBM-DTLA-305040",
- "IBM-DTLA-305030",
- "IBM-DTLA-305020",
- "IC35L010AVER07-0",
- "IC35L020AVER07-0",
- "IC35L030AVER07-0",
- "IC35L040AVER07-0",
- "IC35L060AVER07-0",
- "WDC AC310200R",
- "MAXTOR STM3320620A",
- NULL
-};
-
-static const char *bad_ata66_3[] = {
- "WDC AC310200R",
- NULL
-};
-
-static const char *bad_ata33[] = {
- "Maxtor 92720U8", "Maxtor 92040U6", "Maxtor 91360U4", "Maxtor 91020U3", "Maxtor 90845U3", "Maxtor 90650U2",
- "Maxtor 91360D8", "Maxtor 91190D7", "Maxtor 91020D6", "Maxtor 90845D5", "Maxtor 90680D4", "Maxtor 90510D3", "Maxtor 90340D2",
- "Maxtor 91152D8", "Maxtor 91008D7", "Maxtor 90845D6", "Maxtor 90840D6", "Maxtor 90720D5", "Maxtor 90648D5", "Maxtor 90576D4",
- "Maxtor 90510D4",
- "Maxtor 90432D3", "Maxtor 90288D2", "Maxtor 90256D2",
- "Maxtor 91000D8", "Maxtor 90910D8", "Maxtor 90875D7", "Maxtor 90840D7", "Maxtor 90750D6", "Maxtor 90625D5", "Maxtor 90500D4",
- "Maxtor 91728D8", "Maxtor 91512D7", "Maxtor 91303D6", "Maxtor 91080D5", "Maxtor 90845D4", "Maxtor 90680D4", "Maxtor 90648D3", "Maxtor 90432D2",
- NULL
-};
-
-static u8 xfer_speeds[] = {
- XFER_UDMA_6,
- XFER_UDMA_5,
- XFER_UDMA_4,
- XFER_UDMA_3,
- XFER_UDMA_2,
- XFER_UDMA_1,
- XFER_UDMA_0,
-
- XFER_MW_DMA_2,
- XFER_MW_DMA_1,
- XFER_MW_DMA_0,
-
- XFER_PIO_4,
- XFER_PIO_3,
- XFER_PIO_2,
- XFER_PIO_1,
- XFER_PIO_0
-};
-
-/* Key for bus clock timings
- * 36x 37x
- * bits bits
- * 0:3 0:3 data_high_time. Inactive time of DIOW_/DIOR_ for PIO and MW DMA.
- * cycles = value + 1
- * 4:7 4:8 data_low_time. Active time of DIOW_/DIOR_ for PIO and MW DMA.
- * cycles = value + 1
- * 8:11 9:12 cmd_high_time. Inactive time of DIOW_/DIOR_ during task file
- * register access.
- * 12:15 13:17 cmd_low_time. Active time of DIOW_/DIOR_ during task file
- * register access.
- * 16:18 18:20 udma_cycle_time. Clock cycles for UDMA xfer.
- * - 21 CLK frequency: 0=ATA clock, 1=dual ATA clock.
- * 19:21 22:24 pre_high_time. Time to initialize the 1st cycle for PIO and
- * MW DMA xfer.
- * 22:24 25:27 cmd_pre_high_time. Time to initialize the 1st PIO cycle for
- * task file register access.
- * 28 28 UDMA enable.
- * 29 29 DMA enable.
- * 30 30 PIO MST enable. If set, the chip is in bus master mode during
- * PIO xfer.
- * 31 31 FIFO enable.
- */
-
-static u32 forty_base_hpt36x[] = {
- /* XFER_UDMA_6 */ 0x900fd943,
- /* XFER_UDMA_5 */ 0x900fd943,
- /* XFER_UDMA_4 */ 0x900fd943,
- /* XFER_UDMA_3 */ 0x900ad943,
- /* XFER_UDMA_2 */ 0x900bd943,
- /* XFER_UDMA_1 */ 0x9008d943,
- /* XFER_UDMA_0 */ 0x9008d943,
-
- /* XFER_MW_DMA_2 */ 0xa008d943,
- /* XFER_MW_DMA_1 */ 0xa010d955,
- /* XFER_MW_DMA_0 */ 0xa010d9fc,
-
- /* XFER_PIO_4 */ 0xc008d963,
- /* XFER_PIO_3 */ 0xc010d974,
- /* XFER_PIO_2 */ 0xc010d997,
- /* XFER_PIO_1 */ 0xc010d9c7,
- /* XFER_PIO_0 */ 0xc018d9d9
-};
-
-static u32 thirty_three_base_hpt36x[] = {
- /* XFER_UDMA_6 */ 0x90c9a731,
- /* XFER_UDMA_5 */ 0x90c9a731,
- /* XFER_UDMA_4 */ 0x90c9a731,
- /* XFER_UDMA_3 */ 0x90cfa731,
- /* XFER_UDMA_2 */ 0x90caa731,
- /* XFER_UDMA_1 */ 0x90cba731,
- /* XFER_UDMA_0 */ 0x90c8a731,
-
- /* XFER_MW_DMA_2 */ 0xa0c8a731,
- /* XFER_MW_DMA_1 */ 0xa0c8a732, /* 0xa0c8a733 */
- /* XFER_MW_DMA_0 */ 0xa0c8a797,
-
- /* XFER_PIO_4 */ 0xc0c8a731,
- /* XFER_PIO_3 */ 0xc0c8a742,
- /* XFER_PIO_2 */ 0xc0d0a753,
- /* XFER_PIO_1 */ 0xc0d0a7a3, /* 0xc0d0a793 */
- /* XFER_PIO_0 */ 0xc0d0a7aa /* 0xc0d0a7a7 */
-};
-
-static u32 twenty_five_base_hpt36x[] = {
- /* XFER_UDMA_6 */ 0x90c98521,
- /* XFER_UDMA_5 */ 0x90c98521,
- /* XFER_UDMA_4 */ 0x90c98521,
- /* XFER_UDMA_3 */ 0x90cf8521,
- /* XFER_UDMA_2 */ 0x90cf8521,
- /* XFER_UDMA_1 */ 0x90cb8521,
- /* XFER_UDMA_0 */ 0x90cb8521,
-
- /* XFER_MW_DMA_2 */ 0xa0ca8521,
- /* XFER_MW_DMA_1 */ 0xa0ca8532,
- /* XFER_MW_DMA_0 */ 0xa0ca8575,
-
- /* XFER_PIO_4 */ 0xc0ca8521,
- /* XFER_PIO_3 */ 0xc0ca8532,
- /* XFER_PIO_2 */ 0xc0ca8542,
- /* XFER_PIO_1 */ 0xc0d08572,
- /* XFER_PIO_0 */ 0xc0d08585
-};
-
-/*
- * The following are the new timing tables with PIO mode data/taskfile transfer
- * overclocking fixed...
- */
-
-/* This table is taken from the HPT370 data manual rev. 1.02 */
-static u32 thirty_three_base_hpt37x[] = {
- /* XFER_UDMA_6 */ 0x16455031, /* 0x16655031 ?? */
- /* XFER_UDMA_5 */ 0x16455031,
- /* XFER_UDMA_4 */ 0x16455031,
- /* XFER_UDMA_3 */ 0x166d5031,
- /* XFER_UDMA_2 */ 0x16495031,
- /* XFER_UDMA_1 */ 0x164d5033,
- /* XFER_UDMA_0 */ 0x16515097,
-
- /* XFER_MW_DMA_2 */ 0x26515031,
- /* XFER_MW_DMA_1 */ 0x26515033,
- /* XFER_MW_DMA_0 */ 0x26515097,
-
- /* XFER_PIO_4 */ 0x06515021,
- /* XFER_PIO_3 */ 0x06515022,
- /* XFER_PIO_2 */ 0x06515033,
- /* XFER_PIO_1 */ 0x06915065,
- /* XFER_PIO_0 */ 0x06d1508a
-};
-
-static u32 fifty_base_hpt37x[] = {
- /* XFER_UDMA_6 */ 0x1a861842,
- /* XFER_UDMA_5 */ 0x1a861842,
- /* XFER_UDMA_4 */ 0x1aae1842,
- /* XFER_UDMA_3 */ 0x1a8e1842,
- /* XFER_UDMA_2 */ 0x1a0e1842,
- /* XFER_UDMA_1 */ 0x1a161854,
- /* XFER_UDMA_0 */ 0x1a1a18ea,
-
- /* XFER_MW_DMA_2 */ 0x2a821842,
- /* XFER_MW_DMA_1 */ 0x2a821854,
- /* XFER_MW_DMA_0 */ 0x2a8218ea,
-
- /* XFER_PIO_4 */ 0x0a821842,
- /* XFER_PIO_3 */ 0x0a821843,
- /* XFER_PIO_2 */ 0x0a821855,
- /* XFER_PIO_1 */ 0x0ac218a8,
- /* XFER_PIO_0 */ 0x0b02190c
-};
-
-static u32 sixty_six_base_hpt37x[] = {
- /* XFER_UDMA_6 */ 0x1c86fe62,
- /* XFER_UDMA_5 */ 0x1caefe62, /* 0x1c8afe62 */
- /* XFER_UDMA_4 */ 0x1c8afe62,
- /* XFER_UDMA_3 */ 0x1c8efe62,
- /* XFER_UDMA_2 */ 0x1c92fe62,
- /* XFER_UDMA_1 */ 0x1c9afe62,
- /* XFER_UDMA_0 */ 0x1c82fe62,
-
- /* XFER_MW_DMA_2 */ 0x2c82fe62,
- /* XFER_MW_DMA_1 */ 0x2c82fe66,
- /* XFER_MW_DMA_0 */ 0x2c82ff2e,
-
- /* XFER_PIO_4 */ 0x0c82fe62,
- /* XFER_PIO_3 */ 0x0c82fe84,
- /* XFER_PIO_2 */ 0x0c82fea6,
- /* XFER_PIO_1 */ 0x0d02ff26,
- /* XFER_PIO_0 */ 0x0d42ff7f
-};
-
-#define HPT371_ALLOW_ATA133_6 1
-#define HPT302_ALLOW_ATA133_6 1
-#define HPT372_ALLOW_ATA133_6 1
-#define HPT370_ALLOW_ATA100_5 0
-#define HPT366_ALLOW_ATA66_4 1
-#define HPT366_ALLOW_ATA66_3 1
-
-/* Supported ATA clock frequencies */
-enum ata_clock {
- ATA_CLOCK_25MHZ,
- ATA_CLOCK_33MHZ,
- ATA_CLOCK_40MHZ,
- ATA_CLOCK_50MHZ,
- ATA_CLOCK_66MHZ,
- NUM_ATA_CLOCKS
-};
-
-struct hpt_timings {
- u32 pio_mask;
- u32 dma_mask;
- u32 ultra_mask;
- u32 *clock_table[NUM_ATA_CLOCKS];
-};
-
-/*
- * Hold all the HighPoint chip information in one place.
- */
-
-struct hpt_info {
- char *chip_name; /* Chip name */
- u8 chip_type; /* Chip type */
- u8 udma_mask; /* Allowed UltraDMA modes mask. */
- u8 dpll_clk; /* DPLL clock in MHz */
- u8 pci_clk; /* PCI clock in MHz */
- struct hpt_timings *timings; /* Chipset timing data */
- u8 clock; /* ATA clock selected */
-};
-
-/* Supported HighPoint chips */
-enum {
- HPT36x,
- HPT370,
- HPT370A,
- HPT374,
- HPT372,
- HPT372A,
- HPT302,
- HPT371,
- HPT372N,
- HPT302N,
- HPT371N
-};
-
-static struct hpt_timings hpt36x_timings = {
- .pio_mask = 0xc1f8ffff,
- .dma_mask = 0x303800ff,
- .ultra_mask = 0x30070000,
- .clock_table = {
- [ATA_CLOCK_25MHZ] = twenty_five_base_hpt36x,
- [ATA_CLOCK_33MHZ] = thirty_three_base_hpt36x,
- [ATA_CLOCK_40MHZ] = forty_base_hpt36x,
- [ATA_CLOCK_50MHZ] = NULL,
- [ATA_CLOCK_66MHZ] = NULL
- }
-};
-
-static struct hpt_timings hpt37x_timings = {
- .pio_mask = 0xcfc3ffff,
- .dma_mask = 0x31c001ff,
- .ultra_mask = 0x303c0000,
- .clock_table = {
- [ATA_CLOCK_25MHZ] = NULL,
- [ATA_CLOCK_33MHZ] = thirty_three_base_hpt37x,
- [ATA_CLOCK_40MHZ] = NULL,
- [ATA_CLOCK_50MHZ] = fifty_base_hpt37x,
- [ATA_CLOCK_66MHZ] = sixty_six_base_hpt37x
- }
-};
-
-static const struct hpt_info hpt36x = {
- .chip_name = "HPT36x",
- .chip_type = HPT36x,
- .udma_mask = HPT366_ALLOW_ATA66_3 ? (HPT366_ALLOW_ATA66_4 ? ATA_UDMA4 : ATA_UDMA3) : ATA_UDMA2,
- .dpll_clk = 0, /* no DPLL */
- .timings = &hpt36x_timings
-};
-
-static const struct hpt_info hpt370 = {
- .chip_name = "HPT370",
- .chip_type = HPT370,
- .udma_mask = HPT370_ALLOW_ATA100_5 ? ATA_UDMA5 : ATA_UDMA4,
- .dpll_clk = 48,
- .timings = &hpt37x_timings
-};
-
-static const struct hpt_info hpt370a = {
- .chip_name = "HPT370A",
- .chip_type = HPT370A,
- .udma_mask = HPT370_ALLOW_ATA100_5 ? ATA_UDMA5 : ATA_UDMA4,
- .dpll_clk = 48,
- .timings = &hpt37x_timings
-};
-
-static const struct hpt_info hpt374 = {
- .chip_name = "HPT374",
- .chip_type = HPT374,
- .udma_mask = ATA_UDMA5,
- .dpll_clk = 48,
- .timings = &hpt37x_timings
-};
-
-static const struct hpt_info hpt372 = {
- .chip_name = "HPT372",
- .chip_type = HPT372,
- .udma_mask = HPT372_ALLOW_ATA133_6 ? ATA_UDMA6 : ATA_UDMA5,
- .dpll_clk = 55,
- .timings = &hpt37x_timings
-};
-
-static const struct hpt_info hpt372a = {
- .chip_name = "HPT372A",
- .chip_type = HPT372A,
- .udma_mask = HPT372_ALLOW_ATA133_6 ? ATA_UDMA6 : ATA_UDMA5,
- .dpll_clk = 66,
- .timings = &hpt37x_timings
-};
-
-static const struct hpt_info hpt302 = {
- .chip_name = "HPT302",
- .chip_type = HPT302,
- .udma_mask = HPT302_ALLOW_ATA133_6 ? ATA_UDMA6 : ATA_UDMA5,
- .dpll_clk = 66,
- .timings = &hpt37x_timings
-};
-
-static const struct hpt_info hpt371 = {
- .chip_name = "HPT371",
- .chip_type = HPT371,
- .udma_mask = HPT371_ALLOW_ATA133_6 ? ATA_UDMA6 : ATA_UDMA5,
- .dpll_clk = 66,
- .timings = &hpt37x_timings
-};
-
-static const struct hpt_info hpt372n = {
- .chip_name = "HPT372N",
- .chip_type = HPT372N,
- .udma_mask = HPT372_ALLOW_ATA133_6 ? ATA_UDMA6 : ATA_UDMA5,
- .dpll_clk = 77,
- .timings = &hpt37x_timings
-};
-
-static const struct hpt_info hpt302n = {
- .chip_name = "HPT302N",
- .chip_type = HPT302N,
- .udma_mask = HPT302_ALLOW_ATA133_6 ? ATA_UDMA6 : ATA_UDMA5,
- .dpll_clk = 77,
- .timings = &hpt37x_timings
-};
-
-static const struct hpt_info hpt371n = {
- .chip_name = "HPT371N",
- .chip_type = HPT371N,
- .udma_mask = HPT371_ALLOW_ATA133_6 ? ATA_UDMA6 : ATA_UDMA5,
- .dpll_clk = 77,
- .timings = &hpt37x_timings
-};
-
-static bool check_in_drive_list(ide_drive_t *drive, const char **list)
-{
- return match_string(list, -1, (char *)&drive->id[ATA_ID_PROD]) >= 0;
-}
-
-static struct hpt_info *hpt3xx_get_info(struct device *dev)
-{
- struct ide_host *host = dev_get_drvdata(dev);
- struct hpt_info *info = (struct hpt_info *)host->host_priv;
-
- return dev == host->dev[1] ? info + 1 : info;
-}
-
-/*
- * The Marvell bridge chips used on the HighPoint SATA cards do not seem
- * to support the UltraDMA modes 1, 2, and 3 as well as any MWDMA modes...
- */
-
-static u8 hpt3xx_udma_filter(ide_drive_t *drive)
-{
- ide_hwif_t *hwif = drive->hwif;
- struct hpt_info *info = hpt3xx_get_info(hwif->dev);
- u8 mask = hwif->ultra_mask;
-
- switch (info->chip_type) {
- case HPT36x:
- if (!HPT366_ALLOW_ATA66_4 ||
- check_in_drive_list(drive, bad_ata66_4))
- mask = ATA_UDMA3;
-
- if (!HPT366_ALLOW_ATA66_3 ||
- check_in_drive_list(drive, bad_ata66_3))
- mask = ATA_UDMA2;
- break;
- case HPT370:
- if (!HPT370_ALLOW_ATA100_5 ||
- check_in_drive_list(drive, bad_ata100_5))
- mask = ATA_UDMA4;
- break;
- case HPT370A:
- if (!HPT370_ALLOW_ATA100_5 ||
- check_in_drive_list(drive, bad_ata100_5))
- return ATA_UDMA4;
- fallthrough;
- case HPT372 :
- case HPT372A:
- case HPT372N:
- case HPT374 :
- if (ata_id_is_sata(drive->id))
- mask &= ~0x0e;
- fallthrough;
- default:
- return mask;
- }
-
- return check_in_drive_list(drive, bad_ata33) ? 0x00 : mask;
-}
-
-static u8 hpt3xx_mdma_filter(ide_drive_t *drive)
-{
- ide_hwif_t *hwif = drive->hwif;
- struct hpt_info *info = hpt3xx_get_info(hwif->dev);
-
- switch (info->chip_type) {
- case HPT372 :
- case HPT372A:
- case HPT372N:
- case HPT374 :
- if (ata_id_is_sata(drive->id))
- return 0x00;
- fallthrough;
- default:
- return 0x07;
- }
-}
-
-static u32 get_speed_setting(u8 speed, struct hpt_info *info)
-{
- int i;
-
- /*
- * Lookup the transfer mode table to get the index into
- * the timing table.
- *
- * NOTE: For XFER_PIO_SLOW, PIO mode 0 timings will be used.
- */
- for (i = 0; i < ARRAY_SIZE(xfer_speeds) - 1; i++)
- if (xfer_speeds[i] == speed)
- break;
-
- return info->timings->clock_table[info->clock][i];
-}
-
-static void hpt3xx_set_mode(ide_hwif_t *hwif, ide_drive_t *drive)
-{
- struct pci_dev *dev = to_pci_dev(hwif->dev);
- struct hpt_info *info = hpt3xx_get_info(hwif->dev);
- struct hpt_timings *t = info->timings;
- u8 itr_addr = 0x40 + (drive->dn * 4);
- u32 old_itr = 0;
- const u8 speed = drive->dma_mode;
- u32 new_itr = get_speed_setting(speed, info);
- u32 itr_mask = speed < XFER_MW_DMA_0 ? t->pio_mask :
- (speed < XFER_UDMA_0 ? t->dma_mask :
- t->ultra_mask);
-
- pci_read_config_dword(dev, itr_addr, &old_itr);
- new_itr = (old_itr & ~itr_mask) | (new_itr & itr_mask);
- /*
- * Disable on-chip PIO FIFO/buffer (and PIO MST mode as well)
- * to avoid problems handling I/O errors later
- */
- new_itr &= ~0xc0000000;
-
- pci_write_config_dword(dev, itr_addr, new_itr);
-}
-
-static void hpt3xx_set_pio_mode(ide_hwif_t *hwif, ide_drive_t *drive)
-{
- drive->dma_mode = drive->pio_mode;
- hpt3xx_set_mode(hwif, drive);
-}
-
-static void hpt3xx_maskproc(ide_drive_t *drive, int mask)
-{
- ide_hwif_t *hwif = drive->hwif;
- struct pci_dev *dev = to_pci_dev(hwif->dev);
- struct hpt_info *info = hpt3xx_get_info(hwif->dev);
-
- if ((drive->dev_flags & IDE_DFLAG_NIEN_QUIRK) == 0)
- return;
-
- if (info->chip_type >= HPT370) {
- u8 scr1 = 0;
-
- pci_read_config_byte(dev, 0x5a, &scr1);
- if (((scr1 & 0x10) >> 4) != mask) {
- if (mask)
- scr1 |= 0x10;
- else
- scr1 &= ~0x10;
- pci_write_config_byte(dev, 0x5a, scr1);
- }
- } else if (mask)
- disable_irq(hwif->irq);
- else
- enable_irq(hwif->irq);
-}
-
-/*
- * This is specific to the HPT366 UDMA chipset
- * by HighPoint|Triones Technologies, Inc.
- */
-static void hpt366_dma_lost_irq(ide_drive_t *drive)
-{
- struct pci_dev *dev = to_pci_dev(drive->hwif->dev);
- u8 mcr1 = 0, mcr3 = 0, scr1 = 0;
-
- pci_read_config_byte(dev, 0x50, &mcr1);
- pci_read_config_byte(dev, 0x52, &mcr3);
- pci_read_config_byte(dev, 0x5a, &scr1);
- printk("%s: (%s) mcr1=0x%02x, mcr3=0x%02x, scr1=0x%02x\n",
- drive->name, __func__, mcr1, mcr3, scr1);
- if (scr1 & 0x10)
- pci_write_config_byte(dev, 0x5a, scr1 & ~0x10);
- ide_dma_lost_irq(drive);
-}
-
-static void hpt370_clear_engine(ide_drive_t *drive)
-{
- ide_hwif_t *hwif = drive->hwif;
- struct pci_dev *dev = to_pci_dev(hwif->dev);
-
- pci_write_config_byte(dev, hwif->select_data, 0x37);
- udelay(10);
-}
-
-static void hpt370_irq_timeout(ide_drive_t *drive)
-{
- ide_hwif_t *hwif = drive->hwif;
- struct pci_dev *dev = to_pci_dev(hwif->dev);
- u16 bfifo = 0;
- u8 dma_cmd;
-
- pci_read_config_word(dev, hwif->select_data + 2, &bfifo);
- printk(KERN_DEBUG "%s: %d bytes in FIFO\n", drive->name, bfifo & 0x1ff);
-
- /* get DMA command mode */
- dma_cmd = inb(hwif->dma_base + ATA_DMA_CMD);
- /* stop DMA */
- outb(dma_cmd & ~ATA_DMA_START, hwif->dma_base + ATA_DMA_CMD);
- hpt370_clear_engine(drive);
-}
-
-static void hpt370_dma_start(ide_drive_t *drive)
-{
-#ifdef HPT_RESET_STATE_ENGINE
- hpt370_clear_engine(drive);
-#endif
- ide_dma_start(drive);
-}
-
-static int hpt370_dma_end(ide_drive_t *drive)
-{
- ide_hwif_t *hwif = drive->hwif;
- u8 dma_stat = inb(hwif->dma_base + ATA_DMA_STATUS);
-
- if (dma_stat & ATA_DMA_ACTIVE) {
- /* wait a little */
- udelay(20);
- dma_stat = inb(hwif->dma_base + ATA_DMA_STATUS);
- if (dma_stat & ATA_DMA_ACTIVE)
- hpt370_irq_timeout(drive);
- }
- return ide_dma_end(drive);
-}
-
-/* returns 1 if DMA IRQ issued, 0 otherwise */
-static int hpt374_dma_test_irq(ide_drive_t *drive)
-{
- ide_hwif_t *hwif = drive->hwif;
- struct pci_dev *dev = to_pci_dev(hwif->dev);
- u16 bfifo = 0;
- u8 dma_stat;
-
- pci_read_config_word(dev, hwif->select_data + 2, &bfifo);
- if (bfifo & 0x1FF) {
-// printk("%s: %d bytes in FIFO\n", drive->name, bfifo);
- return 0;
- }
-
- dma_stat = inb(hwif->dma_base + ATA_DMA_STATUS);
- /* return 1 if INTR asserted */
- if (dma_stat & ATA_DMA_INTR)
- return 1;
-
- return 0;
-}
-
-static int hpt374_dma_end(ide_drive_t *drive)
-{
- ide_hwif_t *hwif = drive->hwif;
- struct pci_dev *dev = to_pci_dev(hwif->dev);
- u8 mcr = 0, mcr_addr = hwif->select_data;
- u8 bwsr = 0, mask = hwif->channel ? 0x02 : 0x01;
-
- pci_read_config_byte(dev, 0x6a, &bwsr);
- pci_read_config_byte(dev, mcr_addr, &mcr);
- if (bwsr & mask)
- pci_write_config_byte(dev, mcr_addr, mcr | 0x30);
- return ide_dma_end(drive);
-}
-
-/**
- * hpt3xxn_set_clock - perform clock switching dance
- * @hwif: hwif to switch
- * @mode: clocking mode (0x21 for write, 0x23 otherwise)
- *
- * Switch the DPLL clock on the HPT3xxN devices. This is a right mess.
- */
-
-static void hpt3xxn_set_clock(ide_hwif_t *hwif, u8 mode)
-{
- unsigned long base = hwif->extra_base;
- u8 scr2 = inb(base + 0x6b);
-
- if ((scr2 & 0x7f) == mode)
- return;
-
- /* Tristate the bus */
- outb(0x80, base + 0x63);
- outb(0x80, base + 0x67);
-
- /* Switch clock and reset channels */
- outb(mode, base + 0x6b);
- outb(0xc0, base + 0x69);
-
- /*
- * Reset the state machines.
- * NOTE: avoid accidentally enabling the disabled channels.
- */
- outb(inb(base + 0x60) | 0x32, base + 0x60);
- outb(inb(base + 0x64) | 0x32, base + 0x64);
-
- /* Complete reset */
- outb(0x00, base + 0x69);
-
- /* Reconnect channels to bus */
- outb(0x00, base + 0x63);
- outb(0x00, base + 0x67);
-}
-
-/**
- * hpt3xxn_rw_disk - prepare for I/O
- * @drive: drive for command
- * @rq: block request structure
- *
- * This is called when a disk I/O is issued to HPT3xxN.
- * We need it because of the clock switching.
- */
-
-static void hpt3xxn_rw_disk(ide_drive_t *drive, struct request *rq)
-{
- hpt3xxn_set_clock(drive->hwif, rq_data_dir(rq) ? 0x21 : 0x23);
-}
-
-/**
- * hpt37x_calibrate_dpll - calibrate the DPLL
- * @dev: PCI device
- *
- * Perform a calibration cycle on the DPLL.
- * Returns 1 if this succeeds
- */
-static int hpt37x_calibrate_dpll(struct pci_dev *dev, u16 f_low, u16 f_high)
-{
- u32 dpll = (f_high << 16) | f_low | 0x100;
- u8 scr2;
- int i;
-
- pci_write_config_dword(dev, 0x5c, dpll);
-
- /* Wait for oscillator ready */
- for(i = 0; i < 0x5000; ++i) {
- udelay(50);
- pci_read_config_byte(dev, 0x5b, &scr2);
- if (scr2 & 0x80)
- break;
- }
- /* See if it stays ready (we'll just bail out if it's not yet) */
- for(i = 0; i < 0x1000; ++i) {
- pci_read_config_byte(dev, 0x5b, &scr2);
- /* DPLL destabilized? */
- if(!(scr2 & 0x80))
- return 0;
- }
- /* Turn off tuning, we have the DPLL set */
- pci_read_config_dword (dev, 0x5c, &dpll);
- pci_write_config_dword(dev, 0x5c, (dpll & ~0x100));
- return 1;
-}
-
-static void hpt3xx_disable_fast_irq(struct pci_dev *dev, u8 mcr_addr)
-{
- struct ide_host *host = pci_get_drvdata(dev);
- struct hpt_info *info = host->host_priv + (&dev->dev == host->dev[1]);
- u8 chip_type = info->chip_type;
- u8 new_mcr, old_mcr = 0;
-
- /*
- * Disable the "fast interrupt" prediction. Don't hold off
- * on interrupts. (== 0x01 despite what the docs say)
- */
- pci_read_config_byte(dev, mcr_addr + 1, &old_mcr);
-
- if (chip_type >= HPT374)
- new_mcr = old_mcr & ~0x07;
- else if (chip_type >= HPT370) {
- new_mcr = old_mcr;
- new_mcr &= ~0x02;
-#ifdef HPT_DELAY_INTERRUPT
- new_mcr &= ~0x01;
-#else
- new_mcr |= 0x01;
-#endif
- } else /* HPT366 and HPT368 */
- new_mcr = old_mcr & ~0x80;
-
- if (new_mcr != old_mcr)
- pci_write_config_byte(dev, mcr_addr + 1, new_mcr);
-}
-
-static int init_chipset_hpt366(struct pci_dev *dev)
-{
- unsigned long io_base = pci_resource_start(dev, 4);
- struct hpt_info *info = hpt3xx_get_info(&dev->dev);
- const char *name = DRV_NAME;
- u8 pci_clk, dpll_clk = 0; /* PCI and DPLL clock in MHz */
- u8 chip_type;
- enum ata_clock clock;
-
- chip_type = info->chip_type;
-
- pci_write_config_byte(dev, PCI_CACHE_LINE_SIZE, (L1_CACHE_BYTES / 4));
- pci_write_config_byte(dev, PCI_LATENCY_TIMER, 0x78);
- pci_write_config_byte(dev, PCI_MIN_GNT, 0x08);
- pci_write_config_byte(dev, PCI_MAX_LAT, 0x08);
-
- /*
- * First, try to estimate the PCI clock frequency...
- */
- if (chip_type >= HPT370) {
- u8 scr1 = 0;
- u16 f_cnt = 0;
- u32 temp = 0;
-
- /* Interrupt force enable. */
- pci_read_config_byte(dev, 0x5a, &scr1);
- if (scr1 & 0x10)
- pci_write_config_byte(dev, 0x5a, scr1 & ~0x10);
-
- /*
- * HighPoint does this for HPT372A.
- * NOTE: This register is only writeable via I/O space.
- */
- if (chip_type == HPT372A)
- outb(0x0e, io_base + 0x9c);
-
- /*
- * Default to PCI clock. Make sure MA15/16 are set to output
- * to prevent drives having problems with 40-pin cables.
- */
- pci_write_config_byte(dev, 0x5b, 0x23);
-
- /*
- * We'll have to read f_CNT value in order to determine
- * the PCI clock frequency according to the following ratio:
- *
- * f_CNT = Fpci * 192 / Fdpll
- *
- * First try reading the register in which the HighPoint BIOS
- * saves f_CNT value before reprogramming the DPLL from its
- * default setting (which differs for the various chips).
- *
- * NOTE: This register is only accessible via I/O space;
- * HPT374 BIOS only saves it for the function 0, so we have to
- * always read it from there -- no need to check the result of
- * pci_get_slot() for the function 0 as the whole device has
- * been already "pinned" (via function 1) in init_setup_hpt374()
- */
- if (chip_type == HPT374 && (PCI_FUNC(dev->devfn) & 1)) {
- struct pci_dev *dev1 = pci_get_slot(dev->bus,
- dev->devfn - 1);
- unsigned long io_base = pci_resource_start(dev1, 4);
-
- temp = inl(io_base + 0x90);
- pci_dev_put(dev1);
- } else
- temp = inl(io_base + 0x90);
-
- /*
- * In case the signature check fails, we'll have to
- * resort to reading the f_CNT register itself in hopes
- * that nobody has touched the DPLL yet...
- */
- if ((temp & 0xFFFFF000) != 0xABCDE000) {
- int i;
-
- printk(KERN_WARNING "%s %s: no clock data saved by "
- "BIOS\n", name, pci_name(dev));
-
- /* Calculate the average value of f_CNT. */
- for (temp = i = 0; i < 128; i++) {
- pci_read_config_word(dev, 0x78, &f_cnt);
- temp += f_cnt & 0x1ff;
- mdelay(1);
- }
- f_cnt = temp / 128;
- } else
- f_cnt = temp & 0x1ff;
-
- dpll_clk = info->dpll_clk;
- pci_clk = (f_cnt * dpll_clk) / 192;
-
- /* Clamp PCI clock to bands. */
- if (pci_clk < 40)
- pci_clk = 33;
- else if(pci_clk < 45)
- pci_clk = 40;
- else if(pci_clk < 55)
- pci_clk = 50;
- else
- pci_clk = 66;
-
- printk(KERN_INFO "%s %s: DPLL base: %d MHz, f_CNT: %d, "
- "assuming %d MHz PCI\n", name, pci_name(dev),
- dpll_clk, f_cnt, pci_clk);
- } else {
- u32 itr1 = 0;
-
- pci_read_config_dword(dev, 0x40, &itr1);
-
- /* Detect PCI clock by looking at cmd_high_time. */
- switch ((itr1 >> 8) & 0x0f) {
- case 0x09:
- pci_clk = 40;
- break;
- case 0x05:
- pci_clk = 25;
- break;
- case 0x07:
- default:
- pci_clk = 33;
- break;
- }
- }
-
- /* Let's assume we'll use PCI clock for the ATA clock... */
- switch (pci_clk) {
- case 25:
- clock = ATA_CLOCK_25MHZ;
- break;
- case 33:
- default:
- clock = ATA_CLOCK_33MHZ;
- break;
- case 40:
- clock = ATA_CLOCK_40MHZ;
- break;
- case 50:
- clock = ATA_CLOCK_50MHZ;
- break;
- case 66:
- clock = ATA_CLOCK_66MHZ;
- break;
- }
-
- /*
- * Only try the DPLL if we don't have a table for the PCI clock that
- * we are running at for HPT370/A, always use it for anything newer...
- *
- * NOTE: Using the internal DPLL results in slow reads on 33 MHz PCI.
- * We also don't like using the DPLL because this causes glitches
- * on PRST-/SRST- when the state engine gets reset...
- */
- if (chip_type >= HPT374 || info->timings->clock_table[clock] == NULL) {
- u16 f_low, delta = pci_clk < 50 ? 2 : 4;
- int adjust;
-
- /*
- * Select 66 MHz DPLL clock only if UltraATA/133 mode is
- * supported/enabled, use 50 MHz DPLL clock otherwise...
- */
- if (info->udma_mask == ATA_UDMA6) {
- dpll_clk = 66;
- clock = ATA_CLOCK_66MHZ;
- } else if (dpll_clk) { /* HPT36x chips don't have DPLL */
- dpll_clk = 50;
- clock = ATA_CLOCK_50MHZ;
- }
-
- if (info->timings->clock_table[clock] == NULL) {
- printk(KERN_ERR "%s %s: unknown bus timing!\n",
- name, pci_name(dev));
- return -EIO;
- }
-
- /* Select the DPLL clock. */
- pci_write_config_byte(dev, 0x5b, 0x21);
-
- /*
- * Adjust the DPLL based upon PCI clock, enable it,
- * and wait for stabilization...
- */
- f_low = (pci_clk * 48) / dpll_clk;
-
- for (adjust = 0; adjust < 8; adjust++) {
- if(hpt37x_calibrate_dpll(dev, f_low, f_low + delta))
- break;
-
- /*
- * See if it'll settle at a fractionally different clock
- */
- if (adjust & 1)
- f_low -= adjust >> 1;
- else
- f_low += adjust >> 1;
- }
- if (adjust == 8) {
- printk(KERN_ERR "%s %s: DPLL did not stabilize!\n",
- name, pci_name(dev));
- return -EIO;
- }
-
- printk(KERN_INFO "%s %s: using %d MHz DPLL clock\n",
- name, pci_name(dev), dpll_clk);
- } else {
- /* Mark the fact that we're not using the DPLL. */
- dpll_clk = 0;
-
- printk(KERN_INFO "%s %s: using %d MHz PCI clock\n",
- name, pci_name(dev), pci_clk);
- }
-
- /* Store the clock frequencies. */
- info->dpll_clk = dpll_clk;
- info->pci_clk = pci_clk;
- info->clock = clock;
-
- if (chip_type >= HPT370) {
- u8 mcr1, mcr4;
-
- /*
- * Reset the state engines.
- * NOTE: Avoid accidentally enabling the disabled channels.
- */
- pci_read_config_byte (dev, 0x50, &mcr1);
- pci_read_config_byte (dev, 0x54, &mcr4);
- pci_write_config_byte(dev, 0x50, (mcr1 | 0x32));
- pci_write_config_byte(dev, 0x54, (mcr4 | 0x32));
- udelay(100);
- }
-
- /*
- * On HPT371N, if ATA clock is 66 MHz we must set bit 2 in
- * the MISC. register to stretch the UltraDMA Tss timing.
- * NOTE: This register is only writeable via I/O space.
- */
- if (chip_type == HPT371N && clock == ATA_CLOCK_66MHZ)
- outb(inb(io_base + 0x9c) | 0x04, io_base + 0x9c);
-
- hpt3xx_disable_fast_irq(dev, 0x50);
- hpt3xx_disable_fast_irq(dev, 0x54);
-
- return 0;
-}
-
-static u8 hpt3xx_cable_detect(ide_hwif_t *hwif)
-{
- struct pci_dev *dev = to_pci_dev(hwif->dev);
- struct hpt_info *info = hpt3xx_get_info(hwif->dev);
- u8 chip_type = info->chip_type;
- u8 scr1 = 0, ata66 = hwif->channel ? 0x01 : 0x02;
-
- /*
- * The HPT37x uses the CBLID pins as outputs for MA15/MA16
- * address lines to access an external EEPROM. To read valid
- * cable detect state the pins must be enabled as inputs.
- */
- if (chip_type == HPT374 && (PCI_FUNC(dev->devfn) & 1)) {
- /*
- * HPT374 PCI function 1
- * - set bit 15 of reg 0x52 to enable TCBLID as input
- * - set bit 15 of reg 0x56 to enable FCBLID as input
- */
- u8 mcr_addr = hwif->select_data + 2;
- u16 mcr;
-
- pci_read_config_word(dev, mcr_addr, &mcr);
- pci_write_config_word(dev, mcr_addr, mcr | 0x8000);
- /* Debounce, then read cable ID register */
- udelay(10);
- pci_read_config_byte(dev, 0x5a, &scr1);
- pci_write_config_word(dev, mcr_addr, mcr);
- } else if (chip_type >= HPT370) {
- /*
- * HPT370/372 and 374 pcifn 0
- * - clear bit 0 of reg 0x5b to enable P/SCBLID as inputs
- */
- u8 scr2 = 0;
-
- pci_read_config_byte(dev, 0x5b, &scr2);
- pci_write_config_byte(dev, 0x5b, scr2 & ~1);
- /* Debounce, then read cable ID register */
- udelay(10);
- pci_read_config_byte(dev, 0x5a, &scr1);
- pci_write_config_byte(dev, 0x5b, scr2);
- } else
- pci_read_config_byte(dev, 0x5a, &scr1);
-
- return (scr1 & ata66) ? ATA_CBL_PATA40 : ATA_CBL_PATA80;
-}
-
-static void init_hwif_hpt366(ide_hwif_t *hwif)
-{
- struct hpt_info *info = hpt3xx_get_info(hwif->dev);
- u8 chip_type = info->chip_type;
-
- /* Cache the channel's MISC. control registers' offset */
- hwif->select_data = hwif->channel ? 0x54 : 0x50;
-
- /*
- * HPT3xxN chips have some complications:
- *
- * - on 33 MHz PCI we must clock switch
- * - on 66 MHz PCI we must NOT use the PCI clock
- */
- if (chip_type >= HPT372N && info->dpll_clk && info->pci_clk < 66) {
- /*
- * Clock is shared between the channels,
- * so we'll have to serialize them... :-(
- */
- hwif->host->host_flags |= IDE_HFLAG_SERIALIZE;
- hwif->rw_disk = &hpt3xxn_rw_disk;
- }
-}
-
-static int init_dma_hpt366(ide_hwif_t *hwif,
- const struct ide_port_info *d)
-{
- struct pci_dev *dev = to_pci_dev(hwif->dev);
- unsigned long flags, base = ide_pci_dma_base(hwif, d);
- u8 dma_old, dma_new, masterdma = 0, slavedma = 0;
-
- if (base == 0)
- return -1;
-
- hwif->dma_base = base;
-
- if (ide_pci_check_simplex(hwif, d) < 0)
- return -1;
-
- if (ide_pci_set_master(dev, d->name) < 0)
- return -1;
-
- dma_old = inb(base + 2);
-
- local_irq_save(flags);
-
- dma_new = dma_old;
- pci_read_config_byte(dev, hwif->channel ? 0x4b : 0x43, &masterdma);
- pci_read_config_byte(dev, hwif->channel ? 0x4f : 0x47, &slavedma);
-
- if (masterdma & 0x30) dma_new |= 0x20;
- if ( slavedma & 0x30) dma_new |= 0x40;
- if (dma_new != dma_old)
- outb(dma_new, base + 2);
-
- local_irq_restore(flags);
-
- printk(KERN_INFO " %s: BM-DMA at 0x%04lx-0x%04lx\n",
- hwif->name, base, base + 7);
-
- hwif->extra_base = base + (hwif->channel ? 8 : 16);
-
- if (ide_allocate_dma_engine(hwif))
- return -1;
-
- return 0;
-}
-
-static void hpt374_init(struct pci_dev *dev, struct pci_dev *dev2)
-{
- if (dev2->irq != dev->irq) {
- /* FIXME: we need a core pci_set_interrupt() */
- dev2->irq = dev->irq;
- printk(KERN_INFO DRV_NAME " %s: PCI config space interrupt "
- "fixed\n", pci_name(dev2));
- }
-}
-
-static void hpt371_init(struct pci_dev *dev)
-{
- u8 mcr1 = 0;
-
- /*
- * HPT371 chips physically have only one channel, the secondary one,
- * but the primary channel registers do exist! Go figure...
- * So, we manually disable the non-existing channel here
- * (if the BIOS hasn't done this already).
- */
- pci_read_config_byte(dev, 0x50, &mcr1);
- if (mcr1 & 0x04)
- pci_write_config_byte(dev, 0x50, mcr1 & ~0x04);
-}
-
-static int hpt36x_init(struct pci_dev *dev, struct pci_dev *dev2)
-{
- u8 mcr1 = 0, pin1 = 0, pin2 = 0;
-
- /*
- * Now we'll have to force both channels enabled if
- * at least one of them has been enabled by BIOS...
- */
- pci_read_config_byte(dev, 0x50, &mcr1);
- if (mcr1 & 0x30)
- pci_write_config_byte(dev, 0x50, mcr1 | 0x30);
-
- pci_read_config_byte(dev, PCI_INTERRUPT_PIN, &pin1);
- pci_read_config_byte(dev2, PCI_INTERRUPT_PIN, &pin2);
-
- if (pin1 != pin2 && dev->irq == dev2->irq) {
- printk(KERN_INFO DRV_NAME " %s: onboard version of chipset, "
- "pin1=%d pin2=%d\n", pci_name(dev), pin1, pin2);
- return 1;
- }
-
- return 0;
-}
-
-#define IDE_HFLAGS_HPT3XX \
- (IDE_HFLAG_NO_ATAPI_DMA | \
- IDE_HFLAG_OFF_BOARD)
-
-static const struct ide_port_ops hpt3xx_port_ops = {
- .set_pio_mode = hpt3xx_set_pio_mode,
- .set_dma_mode = hpt3xx_set_mode,
- .maskproc = hpt3xx_maskproc,
- .mdma_filter = hpt3xx_mdma_filter,
- .udma_filter = hpt3xx_udma_filter,
- .cable_detect = hpt3xx_cable_detect,
-};
-
-static const struct ide_dma_ops hpt37x_dma_ops = {
- .dma_host_set = ide_dma_host_set,
- .dma_setup = ide_dma_setup,
- .dma_start = ide_dma_start,
- .dma_end = hpt374_dma_end,
- .dma_test_irq = hpt374_dma_test_irq,
- .dma_lost_irq = ide_dma_lost_irq,
- .dma_timer_expiry = ide_dma_sff_timer_expiry,
- .dma_sff_read_status = ide_dma_sff_read_status,
-};
-
-static const struct ide_dma_ops hpt370_dma_ops = {
- .dma_host_set = ide_dma_host_set,
- .dma_setup = ide_dma_setup,
- .dma_start = hpt370_dma_start,
- .dma_end = hpt370_dma_end,
- .dma_test_irq = ide_dma_test_irq,
- .dma_lost_irq = ide_dma_lost_irq,
- .dma_timer_expiry = ide_dma_sff_timer_expiry,
- .dma_clear = hpt370_irq_timeout,
- .dma_sff_read_status = ide_dma_sff_read_status,
-};
-
-static const struct ide_dma_ops hpt36x_dma_ops = {
- .dma_host_set = ide_dma_host_set,
- .dma_setup = ide_dma_setup,
- .dma_start = ide_dma_start,
- .dma_end = ide_dma_end,
- .dma_test_irq = ide_dma_test_irq,
- .dma_lost_irq = hpt366_dma_lost_irq,
- .dma_timer_expiry = ide_dma_sff_timer_expiry,
- .dma_sff_read_status = ide_dma_sff_read_status,
-};
-
-static const struct ide_port_info hpt366_chipsets[] = {
- { /* 0: HPT36x */
- .name = DRV_NAME,
- .init_chipset = init_chipset_hpt366,
- .init_hwif = init_hwif_hpt366,
- .init_dma = init_dma_hpt366,
- /*
- * HPT36x chips have one channel per function and have
- * both channel enable bits located differently and visible
- * to both functions -- really stupid design decision... :-(
- * Bit 4 is for the primary channel, bit 5 for the secondary.
- */
- .enablebits = {{0x50,0x10,0x10}, {0x54,0x04,0x04}},
- .port_ops = &hpt3xx_port_ops,
- .dma_ops = &hpt36x_dma_ops,
- .host_flags = IDE_HFLAGS_HPT3XX | IDE_HFLAG_SINGLE,
- .pio_mask = ATA_PIO4,
- .mwdma_mask = ATA_MWDMA2,
- },
- { /* 1: HPT3xx */
- .name = DRV_NAME,
- .init_chipset = init_chipset_hpt366,
- .init_hwif = init_hwif_hpt366,
- .init_dma = init_dma_hpt366,
- .enablebits = {{0x50,0x04,0x04}, {0x54,0x04,0x04}},
- .port_ops = &hpt3xx_port_ops,
- .dma_ops = &hpt37x_dma_ops,
- .host_flags = IDE_HFLAGS_HPT3XX,
- .pio_mask = ATA_PIO4,
- .mwdma_mask = ATA_MWDMA2,
- }
-};
-
-/**
- * hpt366_init_one - called when an HPT366 is found
- * @dev: the hpt366 device
- * @id: the matching pci id
- *
- * Called when the PCI registration layer (or the IDE initialization)
- * finds a device matching our IDE device tables.
- */
-static int hpt366_init_one(struct pci_dev *dev, const struct pci_device_id *id)
-{
- const struct hpt_info *info = NULL;
- struct hpt_info *dyn_info;
- struct pci_dev *dev2 = NULL;
- struct ide_port_info d;
- u8 idx = id->driver_data;
- u8 rev = dev->revision;
- int ret;
-
- if ((idx == 0 || idx == 4) && (PCI_FUNC(dev->devfn) & 1))
- return -ENODEV;
-
- switch (idx) {
- case 0:
- if (rev < 3)
- info = &hpt36x;
- else {
- switch (min_t(u8, rev, 6)) {
- case 3: info = &hpt370; break;
- case 4: info = &hpt370a; break;
- case 5: info = &hpt372; break;
- case 6: info = &hpt372n; break;
- }
- idx++;
- }
- break;
- case 1:
- info = (rev > 1) ? &hpt372n : &hpt372a;
- break;
- case 2:
- info = (rev > 1) ? &hpt302n : &hpt302;
- break;
- case 3:
- hpt371_init(dev);
- info = (rev > 1) ? &hpt371n : &hpt371;
- break;
- case 4:
- info = &hpt374;
- break;
- case 5:
- info = &hpt372n;
- break;
- }
-
- printk(KERN_INFO DRV_NAME ": %s chipset detected\n", info->chip_name);
-
- d = hpt366_chipsets[min_t(u8, idx, 1)];
-
- d.udma_mask = info->udma_mask;
-
- /* fixup ->dma_ops for HPT370/HPT370A */
- if (info == &hpt370 || info == &hpt370a)
- d.dma_ops = &hpt370_dma_ops;
-
- if (info == &hpt36x || info == &hpt374)
- dev2 = pci_get_slot(dev->bus, dev->devfn + 1);
-
- dyn_info = kcalloc(dev2 ? 2 : 1, sizeof(*dyn_info), GFP_KERNEL);
- if (dyn_info == NULL) {
- printk(KERN_ERR "%s %s: out of memory!\n",
- d.name, pci_name(dev));
- pci_dev_put(dev2);
- return -ENOMEM;
- }
-
- /*
- * Copy everything from a static "template" structure
- * to just allocated per-chip hpt_info structure.
- */
- memcpy(dyn_info, info, sizeof(*dyn_info));
-
- if (dev2) {
- memcpy(dyn_info + 1, info, sizeof(*dyn_info));
-
- if (info == &hpt374)
- hpt374_init(dev, dev2);
- else {
- if (hpt36x_init(dev, dev2))
- d.host_flags &= ~IDE_HFLAG_NON_BOOTABLE;
- }
-
- ret = ide_pci_init_two(dev, dev2, &d, dyn_info);
- if (ret < 0) {
- pci_dev_put(dev2);
- kfree(dyn_info);
- }
- return ret;
- }
-
- ret = ide_pci_init_one(dev, &d, dyn_info);
- if (ret < 0)
- kfree(dyn_info);
-
- return ret;
-}
-
-static void hpt366_remove(struct pci_dev *dev)
-{
- struct ide_host *host = pci_get_drvdata(dev);
- struct ide_info *info = host->host_priv;
- struct pci_dev *dev2 = host->dev[1] ? to_pci_dev(host->dev[1]) : NULL;
-
- ide_pci_remove(dev);
- pci_dev_put(dev2);
- kfree(info);
-}
-
-static const struct pci_device_id hpt366_pci_tbl[] = {
- { PCI_VDEVICE(TTI, PCI_DEVICE_ID_TTI_HPT366), 0 },
- { PCI_VDEVICE(TTI, PCI_DEVICE_ID_TTI_HPT372), 1 },
- { PCI_VDEVICE(TTI, PCI_DEVICE_ID_TTI_HPT302), 2 },
- { PCI_VDEVICE(TTI, PCI_DEVICE_ID_TTI_HPT371), 3 },
- { PCI_VDEVICE(TTI, PCI_DEVICE_ID_TTI_HPT374), 4 },
- { PCI_VDEVICE(TTI, PCI_DEVICE_ID_TTI_HPT372N), 5 },
- { 0, },
-};
-MODULE_DEVICE_TABLE(pci, hpt366_pci_tbl);
-
-static struct pci_driver hpt366_pci_driver = {
- .name = "HPT366_IDE",
- .id_table = hpt366_pci_tbl,
- .probe = hpt366_init_one,
- .remove = hpt366_remove,
- .suspend = ide_pci_suspend,
- .resume = ide_pci_resume,
-};
-
-static int __init hpt366_ide_init(void)
-{
- return ide_pci_register_driver(&hpt366_pci_driver);
-}
-
-static void __exit hpt366_ide_exit(void)
-{
- pci_unregister_driver(&hpt366_pci_driver);
-}
-
-module_init(hpt366_ide_init);
-module_exit(hpt366_ide_exit);
-
-MODULE_AUTHOR("Andre Hedrick");
-MODULE_DESCRIPTION("PCI driver module for Highpoint HPT366 IDE");
-MODULE_LICENSE("GPL");
generated by cgit v1.2.3 (git 2.39.1) at 2024-11-28 20:31:30 +0000