diff options
Diffstat (limited to 'Documentation/devicetree/bindings/mmc/nvidia,tegra20-sdhci.txt')
| -rw-r--r-- | Documentation/devicetree/bindings/mmc/nvidia,tegra20-sdhci.txt | 143 |
1 files changed, 0 insertions, 143 deletions
diff --git a/Documentation/devicetree/bindings/mmc/nvidia,tegra20-sdhci.txt b/Documentation/devicetree/bindings/mmc/nvidia,tegra20-sdhci.txt deleted file mode 100644 index 96c0b1440c9c..000000000000 --- a/Documentation/devicetree/bindings/mmc/nvidia,tegra20-sdhci.txt +++ /dev/null @@ -1,143 +0,0 @@ -* NVIDIA Tegra Secure Digital Host Controller - -This controller on Tegra family SoCs provides an interface for MMC, SD, -and SDIO types of memory cards. - -This file documents differences between the core properties described -by mmc.txt and the properties used by the sdhci-tegra driver. - -Required properties: -- compatible : should be one of: - - "nvidia,tegra20-sdhci": for Tegra20 - - "nvidia,tegra30-sdhci": for Tegra30 - - "nvidia,tegra114-sdhci": for Tegra114 - - "nvidia,tegra124-sdhci": for Tegra124 and Tegra132 - - "nvidia,tegra210-sdhci": for Tegra210 - - "nvidia,tegra186-sdhci": for Tegra186 - - "nvidia,tegra194-sdhci": for Tegra194 -- clocks: For Tegra210, Tegra186 and Tegra194 must contain two entries. - One for the module clock and one for the timeout clock. - For all other Tegra devices, must contain a single entry for - the module clock. See ../clocks/clock-bindings.txt for details. -- clock-names: For Tegra210, Tegra186 and Tegra194 must contain the - strings 'sdhci' and 'tmclk' to represent the module and - the timeout clocks, respectively. - For all other Tegra devices must contain the string 'sdhci' - to represent the module clock. -- resets : Must contain an entry for each entry in reset-names. - See ../reset/reset.txt for details. -- reset-names : Must include the following entries: - - sdhci - -Optional properties: -- power-gpios : Specify GPIOs for power control - -Example: - -sdhci@c8000200 { - compatible = "nvidia,tegra20-sdhci"; - reg = <0xc8000200 0x200>; - interrupts = <47>; - clocks = <&tegra_car 14>; - resets = <&tegra_car 14>; - reset-names = "sdhci"; - cd-gpios = <&gpio 69 0>; /* gpio PI5 */ - wp-gpios = <&gpio 57 0>; /* gpio PH1 */ - power-gpios = <&gpio 155 0>; /* gpio PT3 */ - bus-width = <8>; -}; - -Optional properties for Tegra210, Tegra186 and Tegra194: -- pinctrl-names, pinctrl-0, pinctrl-1 : Specify pad voltage - configurations. Valid pinctrl-names are "sdmmc-3v3" and "sdmmc-1v8" - for controllers supporting multiple voltage levels. The order of names - should correspond to the pin configuration states in pinctrl-0 and - pinctrl-1. -- pinctrl-names : "sdmmc-3v3-drv" and "sdmmc-1v8-drv" are applicable for - Tegra210 where pad config registers are in the pinmux register domain - for pull-up-strength and pull-down-strength values configuration when - using pads at 3V3 and 1V8 levels. -- nvidia,only-1-8-v : The presence of this property indicates that the - controller operates at a 1.8 V fixed I/O voltage. -- nvidia,pad-autocal-pull-up-offset-3v3, - nvidia,pad-autocal-pull-down-offset-3v3 : Specify drive strength - calibration offsets for 3.3 V signaling modes. -- nvidia,pad-autocal-pull-up-offset-1v8, - nvidia,pad-autocal-pull-down-offset-1v8 : Specify drive strength - calibration offsets for 1.8 V signaling modes. -- nvidia,pad-autocal-pull-up-offset-3v3-timeout, - nvidia,pad-autocal-pull-down-offset-3v3-timeout : Specify drive - strength used as a fallback in case the automatic calibration times - out on a 3.3 V signaling mode. -- nvidia,pad-autocal-pull-up-offset-1v8-timeout, - nvidia,pad-autocal-pull-down-offset-1v8-timeout : Specify drive - strength used as a fallback in case the automatic calibration times - out on a 1.8 V signaling mode. -- nvidia,pad-autocal-pull-up-offset-sdr104, - nvidia,pad-autocal-pull-down-offset-sdr104 : Specify drive strength - calibration offsets for SDR104 mode. -- nvidia,pad-autocal-pull-up-offset-hs400, - nvidia,pad-autocal-pull-down-offset-hs400 : Specify drive strength - calibration offsets for HS400 mode. -- nvidia,default-tap : Specify the default inbound sampling clock - trimmer value for non-tunable modes. -- nvidia,default-trim : Specify the default outbound clock trimmer - value. -- nvidia,dqs-trim : Specify DQS trim value for HS400 timing - - Notes on the pad calibration pull up and pulldown offset values: - - The property values are drive codes which are programmed into the - PD_OFFSET and PU_OFFSET sections of the - SDHCI_TEGRA_AUTO_CAL_CONFIG register. - - A higher value corresponds to higher drive strength. Please refer - to the reference manual of the SoC for correct values. - - The SDR104 and HS400 timing specific values are used in - corresponding modes if specified. - - Notes on tap and trim values: - - The values are used for compensating trace length differences - by adjusting the sampling point. - - The values are programmed to the Vendor Clock Control Register. - Please refer to the reference manual of the SoC for correct - values. - - The DQS trim values are only used on controllers which support - HS400 timing. Only SDMMC4 on Tegra210 and Tegra 186 supports - HS400. - -Example: -sdhci@700b0000 { - compatible = "nvidia,tegra124-sdhci"; - reg = <0x0 0x700b0000 0x0 0x200>; - interrupts = <GIC_SPI 14 IRQ_TYPE_LEVEL_HIGH>; - clocks = <&tegra_car TEGRA210_CLK_SDMMC1>; - clock-names = "sdhci"; - resets = <&tegra_car 14>; - reset-names = "sdhci"; - pinctrl-names = "sdmmc-3v3", "sdmmc-1v8"; - pinctrl-0 = <&sdmmc1_3v3>; - pinctrl-1 = <&sdmmc1_1v8>; - nvidia,pad-autocal-pull-up-offset-3v3 = <0x00>; - nvidia,pad-autocal-pull-down-offset-3v3 = <0x7d>; - nvidia,pad-autocal-pull-up-offset-1v8 = <0x7b>; - nvidia,pad-autocal-pull-down-offset-1v8 = <0x7b>; - status = "disabled"; -}; - -sdhci@700b0000 { - compatible = "nvidia,tegra210-sdhci"; - reg = <0x0 0x700b0000 0x0 0x200>; - interrupts = <GIC_SPI 14 IRQ_TYPE_LEVEL_HIGH>; - clocks = <&tegra_car TEGRA210_CLK_SDMMC1>, - <&tegra_car TEGRA210_CLK_SDMMC_LEGACY>; - clock-names = "sdhci", "tmclk"; - resets = <&tegra_car 14>; - reset-names = "sdhci"; - pinctrl-names = "sdmmc-3v3", "sdmmc-1v8"; - pinctrl-0 = <&sdmmc1_3v3>; - pinctrl-1 = <&sdmmc1_1v8>; - nvidia,pad-autocal-pull-up-offset-3v3 = <0x00>; - nvidia,pad-autocal-pull-down-offset-3v3 = <0x7d>; - nvidia,pad-autocal-pull-up-offset-1v8 = <0x7b>; - nvidia,pad-autocal-pull-down-offset-1v8 = <0x7b>; - status = "disabled"; -}; |