1 files changed, 0 insertions, 133 deletions
diff --git a/Documentation/devicetree/bindings/arm/tegra/nvidia,tegra186-pmc.txt b/Documentation/devicetree/bindings/arm/tegra/nvidia,tegra186-pmc.txt
deleted file mode 100644
index 576462fae27f..000000000000
--- a/Documentation/devicetree/bindings/arm/tegra/nvidia,tegra186-pmc.txt
+++ /dev/null
@@ -1,133 +0,0 @@
-NVIDIA Tegra Power Management Controller (PMC)
-
-Required properties:
-- compatible: Should contain one of the following:
-  - "nvidia,tegra186-pmc": for Tegra186
-  - "nvidia,tegra194-pmc": for Tegra194
-  - "nvidia,tegra234-pmc": for Tegra234
-- reg: Must contain an (offset, length) pair of the register set for each
-  entry in reg-names.
-- reg-names: Must include the following entries:
-  - "pmc"
-  - "wake"
-  - "aotag"
-  - "scratch"
-  - "misc" (Only for Tegra194 and later)
-
-Optional properties:
-- nvidia,invert-interrupt: If present, inverts the PMU interrupt signal.
-- interrupt-controller: Identifies the node as an interrupt controller.
-- #interrupt-cells: Specifies the number of cells needed to encode an
-  interrupt source. The value must be 2.
-
-Example:
-
-SoC DTSI:
-
-	pmc@c3600000 {
-		compatible = "nvidia,tegra186-pmc";
-		reg = <0 0x0c360000 0 0x10000>,
-		      <0 0x0c370000 0 0x10000>,
-		      <0 0x0c380000 0 0x10000>,
-		      <0 0x0c390000 0 0x10000>;
-		reg-names = "pmc", "wake", "aotag", "scratch";
-	};
-
-Board DTS:
-
-	pmc@c360000 {
-		nvidia,invert-interrupt;
-	};
-
-== Pad Control ==
-
-On Tegra SoCs a pad is a set of pins which are configured as a group.
-The pin grouping is a fixed attribute of the hardware. The PMC can be
-used to set pad power state and signaling voltage. A pad can be either
-in active or power down mode. The support for power state and signaling
-voltage configuration varies depending on the pad in question. 3.3 V and
-1.8 V signaling voltages are supported on pins where software
-controllable signaling voltage switching is available.
-
-Pad configurations are described with pin configuration nodes which
-are placed under the pmc node and they are referred to by the pinctrl
-client properties. For more information see
-Documentation/devicetree/bindings/pinctrl/pinctrl-bindings.txt.
-
-The following pads are present on Tegra186:
-csia		csib		dsi		mipi-bias
-pex-clk-bias	pex-clk3	pex-clk2	pex-clk1
-usb0		usb1		usb2		usb-bias
-uart		audio		hsic		dbg
-hdmi-dp0	hdmi-dp1	pex-cntrl	sdmmc2-hv
-sdmmc4		cam		dsib		dsic
-dsid		csic		csid		csie
-dsif		spi		ufs		dmic-hv
-edp		sdmmc1-hv	sdmmc3-hv	conn
-audio-hv	ao-hv
-
-Required pin configuration properties:
-  - pins: A list of strings, each of which contains the name of a pad
-	  to be configured.
-
-Optional pin configuration properties:
-  - low-power-enable: Configure the pad into power down mode
-  - low-power-disable: Configure the pad into active mode
-  - power-source: Must contain either TEGRA_IO_PAD_VOLTAGE_1V8 or
-    TEGRA_IO_PAD_VOLTAGE_3V3 to select between signaling voltages.
-    The values are defined in
-    include/dt-bindings/pinctrl/pinctrl-tegra-io-pad.h.
-
-Note: The power state can be configured on all of the above pads except
-      for ao-hv. Following pads have software configurable signaling
-      voltages: sdmmc2-hv, dmic-hv, sdmmc1-hv, sdmmc3-hv, audio-hv,
-      ao-hv.
-
-Pad configuration state example:
-	pmc: pmc@7000e400 {
-		compatible = "nvidia,tegra186-pmc";
-		reg = <0 0x0c360000 0 0x10000>,
-		      <0 0x0c370000 0 0x10000>,
-		      <0 0x0c380000 0 0x10000>,
-		      <0 0x0c390000 0 0x10000>;
-		reg-names = "pmc", "wake", "aotag", "scratch";
-
-		...
-
-		sdmmc1_3v3: sdmmc1-3v3 {
-			pins = "sdmmc1-hv";
-			power-source = <TEGRA_IO_PAD_VOLTAGE_3V3>;
-		};
-
-		sdmmc1_1v8: sdmmc1-1v8 {
-			pins = "sdmmc1-hv";
-			power-source = <TEGRA_IO_PAD_VOLTAGE_1V8>;
-		};
-
-		hdmi_off: hdmi-off {
-			pins = "hdmi";
-			low-power-enable;
-		}
-
-		hdmi_on: hdmi-on {
-			pins = "hdmi";
-			low-power-disable;
-		}
-	};
-
-Pinctrl client example:
-	sdmmc1: sdhci@3400000 {
-		...
-		pinctrl-names = "sdmmc-3v3", "sdmmc-1v8";
-		pinctrl-0 = <&sdmmc1_3v3>;
-		pinctrl-1 = <&sdmmc1_1v8>;
-	};
-
-	...
-
-	sor0: sor@15540000 {
-		...
-		pinctrl-0 = <&hdmi_off>;
-		pinctrl-1 = <&hdmi_on>;
-		pinctrl-names = "hdmi-on", "hdmi-off";
-	};