diff options
Diffstat (limited to 'arch/ppc/kernel/head.S')
| -rw-r--r-- | arch/ppc/kernel/head.S | 183 |
1 files changed, 4 insertions, 179 deletions
diff --git a/arch/ppc/kernel/head.S b/arch/ppc/kernel/head.S index 53ea845fb911..01303efeddad 100644 --- a/arch/ppc/kernel/head.S +++ b/arch/ppc/kernel/head.S @@ -37,19 +37,6 @@ #include <asm/amigappc.h> #endif -#ifdef CONFIG_PPC64BRIDGE -#define LOAD_BAT(n, reg, RA, RB) \ - ld RA,(n*32)+0(reg); \ - ld RB,(n*32)+8(reg); \ - mtspr SPRN_IBAT##n##U,RA; \ - mtspr SPRN_IBAT##n##L,RB; \ - ld RA,(n*32)+16(reg); \ - ld RB,(n*32)+24(reg); \ - mtspr SPRN_DBAT##n##U,RA; \ - mtspr SPRN_DBAT##n##L,RB; \ - -#else /* CONFIG_PPC64BRIDGE */ - /* 601 only have IBAT; cr0.eq is set on 601 when using this macro */ #define LOAD_BAT(n, reg, RA, RB) \ /* see the comment for clear_bats() -- Cort */ \ @@ -66,7 +53,6 @@ mtspr SPRN_DBAT##n##U,RA; \ mtspr SPRN_DBAT##n##L,RB; \ 1: -#endif /* CONFIG_PPC64BRIDGE */ .text .stabs "arch/ppc/kernel/",N_SO,0,0,0f @@ -129,11 +115,6 @@ _start: .globl __start __start: -/* - * We have to do any OF calls before we map ourselves to KERNELBASE, - * because OF may have I/O devices mapped into that area - * (particularly on CHRP). - */ mr r31,r3 /* save parameters */ mr r30,r4 mr r29,r5 @@ -148,14 +129,6 @@ __start: */ bl early_init -/* - * On POWER4, we first need to tweak some CPU configuration registers - * like real mode cache inhibit or exception base - */ -#ifdef CONFIG_POWER4 - bl __970_cpu_preinit -#endif /* CONFIG_POWER4 */ - #ifdef CONFIG_APUS /* On APUS the __va/__pa constants need to be set to the correct * values before continuing. @@ -169,7 +142,6 @@ __start: */ bl mmu_off __after_mmu_off: -#ifndef CONFIG_POWER4 bl clear_bats bl flush_tlbs @@ -177,10 +149,6 @@ __after_mmu_off: #if !defined(CONFIG_APUS) && defined(CONFIG_BOOTX_TEXT) bl setup_disp_bat #endif -#else /* CONFIG_POWER4 */ - bl reloc_offset - bl initial_mm_power4 -#endif /* CONFIG_POWER4 */ /* * Call setup_cpu for CPU 0 and initialize 6xx Idle @@ -192,18 +160,11 @@ __after_mmu_off: bl reloc_offset bl init_idle_6xx #endif /* CONFIG_6xx */ -#ifdef CONFIG_POWER4 - bl reloc_offset - bl init_idle_power4 -#endif /* CONFIG_POWER4 */ #ifndef CONFIG_APUS /* * We need to run with _start at physical address 0. - * On CHRP, we are loaded at 0x10000 since OF on CHRP uses - * the exception vectors at 0 (and therefore this copy - * overwrites OF's exception vectors with our own). * If the MMU is already turned on, we copy stuff to KERNELBASE, * otherwise we copy it to 0. */ @@ -358,51 +319,19 @@ i##n: \ #endif /* Machine check */ -/* - * On CHRP, this is complicated by the fact that we could get a - * machine check inside RTAS, and we have no guarantee that certain - * critical registers will have the values we expect. The set of - * registers that might have bad values includes all the GPRs - * and all the BATs. We indicate that we are in RTAS by putting - * a non-zero value, the address of the exception frame to use, - * in SPRG2. The machine check handler checks SPRG2 and uses its - * value if it is non-zero. If we ever needed to free up SPRG2, - * we could use a field in the thread_info or thread_struct instead. - * (Other exception handlers assume that r1 is a valid kernel stack - * pointer when we take an exception from supervisor mode.) - * -- paulus. - */ . = 0x200 mtspr SPRN_SPRG0,r10 mtspr SPRN_SPRG1,r11 mfcr r10 -#ifdef CONFIG_PPC_CHRP - mfspr r11,SPRN_SPRG2 - cmpwi 0,r11,0 - bne 7f -#endif /* CONFIG_PPC_CHRP */ EXCEPTION_PROLOG_1 7: EXCEPTION_PROLOG_2 addi r3,r1,STACK_FRAME_OVERHEAD -#ifdef CONFIG_PPC_CHRP - mfspr r4,SPRN_SPRG2 - cmpwi cr1,r4,0 - bne cr1,1f -#endif EXC_XFER_STD(0x200, machine_check_exception) -#ifdef CONFIG_PPC_CHRP -1: b machine_check_in_rtas -#endif /* Data access exception. */ . = 0x300 -#ifdef CONFIG_PPC64BRIDGE - b DataAccess -DataAccessCont: -#else DataAccess: EXCEPTION_PROLOG -#endif /* CONFIG_PPC64BRIDGE */ mfspr r10,SPRN_DSISR andis. r0,r10,0xa470 /* weird error? */ bne 1f /* if not, try to put a PTE */ @@ -414,21 +343,10 @@ DataAccess: mfspr r4,SPRN_DAR EXC_XFER_EE_LITE(0x300, handle_page_fault) -#ifdef CONFIG_PPC64BRIDGE -/* SLB fault on data access. */ - . = 0x380 - b DataSegment -#endif /* CONFIG_PPC64BRIDGE */ - /* Instruction access exception. */ . = 0x400 -#ifdef CONFIG_PPC64BRIDGE - b InstructionAccess -InstructionAccessCont: -#else InstructionAccess: EXCEPTION_PROLOG -#endif /* CONFIG_PPC64BRIDGE */ andis. r0,r9,0x4000 /* no pte found? */ beq 1f /* if so, try to put a PTE */ li r3,0 /* into the hash table */ @@ -438,12 +356,6 @@ InstructionAccess: mr r5,r9 EXC_XFER_EE_LITE(0x400, handle_page_fault) -#ifdef CONFIG_PPC64BRIDGE -/* SLB fault on instruction access. */ - . = 0x480 - b InstructionSegment -#endif /* CONFIG_PPC64BRIDGE */ - /* External interrupt */ EXCEPTION(0x500, HardwareInterrupt, do_IRQ, EXC_XFER_LITE) @@ -708,15 +620,9 @@ DataStoreTLBMiss: EXCEPTION(0x1300, Trap_13, instruction_breakpoint_exception, EXC_XFER_EE) EXCEPTION(0x1400, SMI, SMIException, EXC_XFER_EE) EXCEPTION(0x1500, Trap_15, unknown_exception, EXC_XFER_EE) -#ifdef CONFIG_POWER4 - EXCEPTION(0x1600, Trap_16, unknown_exception, EXC_XFER_EE) - EXCEPTION(0x1700, Trap_17, altivec_assist_exception, EXC_XFER_EE) - EXCEPTION(0x1800, Trap_18, TAUException, EXC_XFER_STD) -#else /* !CONFIG_POWER4 */ EXCEPTION(0x1600, Trap_16, altivec_assist_exception, EXC_XFER_EE) EXCEPTION(0x1700, Trap_17, TAUException, EXC_XFER_STD) EXCEPTION(0x1800, Trap_18, unknown_exception, EXC_XFER_EE) -#endif /* CONFIG_POWER4 */ EXCEPTION(0x1900, Trap_19, unknown_exception, EXC_XFER_EE) EXCEPTION(0x1a00, Trap_1a, unknown_exception, EXC_XFER_EE) EXCEPTION(0x1b00, Trap_1b, unknown_exception, EXC_XFER_EE) @@ -754,28 +660,6 @@ AltiVecUnavailable: addi r3,r1,STACK_FRAME_OVERHEAD EXC_XFER_EE_LITE(0xf20, altivec_unavailable_exception) -#ifdef CONFIG_PPC64BRIDGE -DataAccess: - EXCEPTION_PROLOG - b DataAccessCont - -InstructionAccess: - EXCEPTION_PROLOG - b InstructionAccessCont - -DataSegment: - EXCEPTION_PROLOG - addi r3,r1,STACK_FRAME_OVERHEAD - mfspr r4,SPRN_DAR - stw r4,_DAR(r11) - EXC_XFER_STD(0x380, unknown_exception) - -InstructionSegment: - EXCEPTION_PROLOG - addi r3,r1,STACK_FRAME_OVERHEAD - EXC_XFER_STD(0x480, unknown_exception) -#endif /* CONFIG_PPC64BRIDGE */ - #ifdef CONFIG_ALTIVEC /* Note that the AltiVec support is closely modeled after the FP * support. Changes to one are likely to be applicable to the @@ -1048,13 +932,6 @@ __secondary_start_pmac_0: .globl __secondary_start __secondary_start: -#ifdef CONFIG_PPC64BRIDGE - mfmsr r0 - clrldi r0,r0,1 /* make sure it's in 32-bit mode */ - SYNC - MTMSRD(r0) - isync -#endif /* Copy some CPU settings from CPU 0 */ bl __restore_cpu_setup @@ -1065,10 +942,6 @@ __secondary_start: lis r3,-KERNELBASE@h bl init_idle_6xx #endif /* CONFIG_6xx */ -#ifdef CONFIG_POWER4 - lis r3,-KERNELBASE@h - bl init_idle_power4 -#endif /* CONFIG_POWER4 */ /* get current_thread_info and current */ lis r1,secondary_ti@ha @@ -1109,12 +982,12 @@ __secondary_start: * Those generic dummy functions are kept for CPUs not * included in CONFIG_6xx */ -#if !defined(CONFIG_6xx) && !defined(CONFIG_POWER4) +#if !defined(CONFIG_6xx) _GLOBAL(__save_cpu_setup) blr _GLOBAL(__restore_cpu_setup) blr -#endif /* !defined(CONFIG_6xx) && !defined(CONFIG_POWER4) */ +#endif /* !defined(CONFIG_6xx) */ /* @@ -1132,11 +1005,6 @@ load_up_mmu: tophys(r6,r6) lwz r6,_SDR1@l(r6) mtspr SPRN_SDR1,r6 -#ifdef CONFIG_PPC64BRIDGE - /* clear the ASR so we only use the pseudo-segment registers. */ - li r6,0 - mtasr r6 -#endif /* CONFIG_PPC64BRIDGE */ li r0,16 /* load up segment register values */ mtctr r0 /* for context 0 */ lis r3,0x2000 /* Ku = 1, VSID = 0 */ @@ -1145,7 +1013,7 @@ load_up_mmu: addi r3,r3,0x111 /* increment VSID */ addis r4,r4,0x1000 /* address of next segment */ bdnz 3b -#ifndef CONFIG_POWER4 + /* Load the BAT registers with the values set up by MMU_init. MMU_init takes care of whether we're on a 601 or not. */ mfpvr r3 @@ -1158,7 +1026,7 @@ load_up_mmu: LOAD_BAT(1,r3,r4,r5) LOAD_BAT(2,r3,r4,r5) LOAD_BAT(3,r3,r4,r5) -#endif /* CONFIG_POWER4 */ + blr /* @@ -1269,9 +1137,6 @@ _GLOBAL(set_context) li r4,0 isync 3: -#ifdef CONFIG_PPC64BRIDGE - slbie r4 -#endif /* CONFIG_PPC64BRIDGE */ mtsrin r3,r4 addi r3,r3,0x111 /* next VSID */ rlwinm r3,r3,0,8,3 /* clear out any overflow from VSID field */ @@ -1358,7 +1223,6 @@ mmu_off: sync RFI -#ifndef CONFIG_POWER4 /* * Use the first pair of BAT registers to map the 1st 16MB * of RAM to KERNELBASE. From this point on we can't safely @@ -1366,7 +1230,6 @@ mmu_off: */ initial_bats: lis r11,KERNELBASE@h -#ifndef CONFIG_PPC64BRIDGE mfspr r9,SPRN_PVR rlwinm r9,r9,16,16,31 /* r9 = 1 for 601, 4 for 604 */ cmpwi 0,r9,1 @@ -1381,7 +1244,6 @@ initial_bats: mtspr SPRN_IBAT1L,r10 isync blr -#endif /* CONFIG_PPC64BRIDGE */ 4: tophys(r8,r11) #ifdef CONFIG_SMP @@ -1395,11 +1257,6 @@ initial_bats: ori r11,r11,BL_256M<<2|0x2 /* set up BAT registers for 604 */ #endif /* CONFIG_APUS */ -#ifdef CONFIG_PPC64BRIDGE - /* clear out the high 32 bits in the BAT */ - clrldi r11,r11,32 - clrldi r8,r8,32 -#endif /* CONFIG_PPC64BRIDGE */ mtspr SPRN_DBAT0L,r8 /* N.B. 6xx (not 601) have valid */ mtspr SPRN_DBAT0U,r11 /* bit in upper BAT register */ mtspr SPRN_IBAT0L,r8 @@ -1432,38 +1289,6 @@ setup_disp_bat: #endif /* !defined(CONFIG_APUS) && defined(CONFIG_BOOTX_TEXT) */ -#else /* CONFIG_POWER4 */ -/* - * Load up the SDR1 and segment register values now - * since we don't have the BATs. - * Also make sure we are running in 32-bit mode. - */ - -initial_mm_power4: - addis r14,r3,_SDR1@ha /* get the value from _SDR1 */ - lwz r14,_SDR1@l(r14) /* assume hash table below 4GB */ - mtspr SPRN_SDR1,r14 - slbia - lis r4,0x2000 /* set pseudo-segment reg 12 */ - ori r5,r4,0x0ccc - mtsr 12,r5 -#if 0 - ori r5,r4,0x0888 /* set pseudo-segment reg 8 */ - mtsr 8,r5 /* (for access to serial port) */ -#endif -#ifdef CONFIG_BOOTX_TEXT - ori r5,r4,0x0999 /* set pseudo-segment reg 9 */ - mtsr 9,r5 /* (for access to screen) */ -#endif - mfmsr r0 - clrldi r0,r0,1 - sync - mtmsr r0 - isync - blr - -#endif /* CONFIG_POWER4 */ - #ifdef CONFIG_8260 /* Jump into the system reset for the rom. * We first disable the MMU, and then jump to the ROM reset address. |