ASoC: rt5677: Add a configuration option for LDO2_POW pin

Some boards have this pin statically tied and do not require any configuration,
some other boards allow to enable chip using GPIO.

Add an option that tells which GPIO is used to power the audio codec.

Signed-off-by: Anatol Pomozov <anatol.pomozov@gmail.com>
Signed-off-by: Mark Brown <broonie@kernel.org>

2 files changed, 55 insertions, 0 deletions

diff --git a/sound/soc/codecs/rt5677.c b/sound/soc/codecs/rt5677.c
index 4a0f3dfb2a47..d2c6abf38ad2 100644
--- a/sound/soc/codecs/rt5677.c
+++ b/sound/soc/codecs/rt5677.c
@@ -15,6 +15,7 @@
 #include <linux/init.h>
 #include <linux/delay.h>
 #include <linux/pm.h>
+#include <linux/of_gpio.h>
 #include <linux/regmap.h>
 #include <linux/i2c.h>
 #include <linux/platform_device.h>
@@ -3381,6 +3382,8 @@ static int rt5677_remove(struct snd_soc_codec *codec)
 	struct rt5677_priv *rt5677 = snd_soc_codec_get_drvdata(codec);
 
 	regmap_write(rt5677->regmap, RT5677_RESET, 0x10ec);
+	if (gpio_is_valid(rt5677->pow_ldo2))
+		gpio_set_value_cansleep(rt5677->pow_ldo2, 0);
 
 	return 0;
 }
@@ -3392,6 +3395,8 @@ static int rt5677_suspend(struct snd_soc_codec *codec)
 
 	regcache_cache_only(rt5677->regmap, true);
 	regcache_mark_dirty(rt5677->regmap);
+	if (gpio_is_valid(rt5677->pow_ldo2))
+		gpio_set_value_cansleep(rt5677->pow_ldo2, 0);
 
 	return 0;
 }
@@ -3400,6 +3405,10 @@ static int rt5677_resume(struct snd_soc_codec *codec)
 {
 	struct rt5677_priv *rt5677 = snd_soc_codec_get_drvdata(codec);
 
+	if (gpio_is_valid(rt5677->pow_ldo2)) {
+		gpio_set_value_cansleep(rt5677->pow_ldo2, 1);
+		msleep(10);
+	}
 	regcache_cache_only(rt5677->regmap, false);
 	regcache_sync(rt5677->regmap);
 
@@ -3558,6 +3567,24 @@ static const struct i2c_device_id rt5677_i2c_id[] = {
 };
 MODULE_DEVICE_TABLE(i2c, rt5677_i2c_id);
 
+static int rt5677_parse_dt(struct rt5677_priv *rt5677, struct device_node *np)
+{
+	rt5677->pow_ldo2 = of_get_named_gpio(np,
+					"realtek,pow-ldo2-gpio", 0);
+
+	/*
+	 * POW_LDO2 is optional (it may be statically tied on the board).
+	 * -ENOENT means that the property doesn't exist, i.e. there is no
+	 * GPIO, so is not an error. Any other error code means the property
+	 * exists, but could not be parsed.
+	 */
+	if (!gpio_is_valid(rt5677->pow_ldo2) &&
+			(rt5677->pow_ldo2 != -ENOENT))
+		return rt5677->pow_ldo2;
+
+	return 0;
+}
+
 static int rt5677_i2c_probe(struct i2c_client *i2c,
 		    const struct i2c_device_id *id)
 {
@@ -3576,6 +3603,33 @@ static int rt5677_i2c_probe(struct i2c_client *i2c,
 	if (pdata)
 		rt5677->pdata = *pdata;
 
+	if (i2c->dev.of_node) {
+		ret = rt5677_parse_dt(rt5677, i2c->dev.of_node);
+		if (ret) {
+			dev_err(&i2c->dev, "Failed to parse device tree: %d\n",
+				ret);
+			return ret;
+		}
+	} else {
+		rt5677->pow_ldo2 = -EINVAL;
+	}
+
+	if (gpio_is_valid(rt5677->pow_ldo2)) {
+		ret = devm_gpio_request_one(&i2c->dev, rt5677->pow_ldo2,
+					    GPIOF_OUT_INIT_HIGH,
+					    "RT5677 POW_LDO2");
+		if (ret < 0) {
+			dev_err(&i2c->dev, "Failed to request POW_LDO2 %d: %d\n",
+				rt5677->pow_ldo2, ret);
+			return ret;
+		}
+		/* Wait a while until I2C bus becomes available. The datasheet
+		 * does not specify the exact we should wait but startup
+		 * sequence mentiones at least a few milliseconds.
+		 */
+		msleep(10);
+	}
+
 	rt5677->regmap = devm_regmap_init_i2c(i2c, &rt5677_regmap);
 	if (IS_ERR(rt5677->regmap)) {
 		ret = PTR_ERR(rt5677->regmap);
diff --git a/sound/soc/codecs/rt5677.h b/sound/soc/codecs/rt5677.h
index 1fe88727a063..d4eb6d5e6746 100644
--- a/sound/soc/codecs/rt5677.h
+++ b/sound/soc/codecs/rt5677.h
@@ -1554,6 +1554,7 @@ struct rt5677_priv {
 	int pll_src;
 	int pll_in;
 	int pll_out;
+	int pow_ldo2; /* POW_LDO2 pin */
 #ifdef CONFIG_GPIOLIB
 	struct gpio_chip gpio_chip;
 #endif