ARC: intc: split into ARCompact ISA specific, common bits

Signed-off-by: Vineet Gupta <vgupta@synopsys.com>

1 files changed, 0 insertions, 210 deletions

diff --git a/arch/arc/kernel/irq.c b/arch/arc/kernel/irq.c
index 620ec2fe32a9..2989a7bcf8a8 100644
--- a/arch/arc/kernel/irq.c
+++ b/arch/arc/kernel/irq.c
@@ -8,116 +8,10 @@
  */
 
 #include <linux/interrupt.h>
-#include <linux/module.h>
-#include <linux/of.h>
-#include <linux/irqdomain.h>
 #include <linux/irqchip.h>
-#include "../../drivers/irqchip/irqchip.h"
-#include <asm/sections.h>
-#include <asm/irq.h>
 #include <asm/mach_desc.h>
 
 /*
- * Early Hardware specific Interrupt setup
- * -Platform independent, needed for each CPU (not foldable into init_IRQ)
- * -Called very early (start_kernel -> setup_arch -> setup_processor)
- *
- * what it does ?
- * -Optionally, setup the High priority Interrupts as Level 2 IRQs
- */
-void arc_init_IRQ(void)
-{
-	int level_mask = 0;
-
-       /* setup any high priority Interrupts (Level2 in ARCompact jargon) */
-	level_mask |= IS_ENABLED(CONFIG_ARC_IRQ3_LV2) << 3;
-	level_mask |= IS_ENABLED(CONFIG_ARC_IRQ5_LV2) << 5;
-	level_mask |= IS_ENABLED(CONFIG_ARC_IRQ6_LV2) << 6;
-
-	/*
-	 * Write to register, even if no LV2 IRQs configured to reset it
-	 * in case bootloader had mucked with it
-	 */
-	write_aux_reg(AUX_IRQ_LEV, level_mask);
-
-	if (level_mask)
-		pr_info("Level-2 interrupts bitset %x\n", level_mask);
-}
-
-/*
- * ARC700 core includes a simple on-chip intc supporting
- * -per IRQ enable/disable
- * -2 levels of interrupts (high/low)
- * -all interrupts being level triggered
- *
- * To reduce platform code, we assume all IRQs directly hooked-up into intc.
- * Platforms with external intc, hence cascaded IRQs, are free to over-ride
- * below, per IRQ.
- */
-
-static void arc_irq_mask(struct irq_data *data)
-{
-	unsigned int ienb;
-
-	ienb = read_aux_reg(AUX_IENABLE);
-	ienb &= ~(1 << data->irq);
-	write_aux_reg(AUX_IENABLE, ienb);
-}
-
-static void arc_irq_unmask(struct irq_data *data)
-{
-	unsigned int ienb;
-
-	ienb = read_aux_reg(AUX_IENABLE);
-	ienb |= (1 << data->irq);
-	write_aux_reg(AUX_IENABLE, ienb);
-}
-
-static struct irq_chip onchip_intc = {
-	.name           = "ARC In-core Intc",
-	.irq_mask	= arc_irq_mask,
-	.irq_unmask	= arc_irq_unmask,
-};
-
-static int arc_intc_domain_map(struct irq_domain *d, unsigned int irq,
-				irq_hw_number_t hw)
-{
-	if (irq == TIMER0_IRQ)
-		irq_set_chip_and_handler(irq, &onchip_intc, handle_percpu_irq);
-	else
-		irq_set_chip_and_handler(irq, &onchip_intc, handle_level_irq);
-
-	return 0;
-}
-
-static const struct irq_domain_ops arc_intc_domain_ops = {
-	.xlate = irq_domain_xlate_onecell,
-	.map = arc_intc_domain_map,
-};
-
-static struct irq_domain *root_domain;
-
-static int __init
-init_onchip_IRQ(struct device_node *intc, struct device_node *parent)
-{
-	if (parent)
-		panic("DeviceTree incore intc not a root irq controller\n");
-
-	root_domain = irq_domain_add_legacy(intc, NR_CPU_IRQS, 0, 0,
-					    &arc_intc_domain_ops, NULL);
-
-	if (!root_domain)
-		panic("root irq domain not avail\n");
-
-	/* with this we don't need to export root_domain */
-	irq_set_default_host(root_domain);
-
-	return 0;
-}
-
-IRQCHIP_DECLARE(arc_intc, "snps,arc700-intc", init_onchip_IRQ);
-
-/*
  * Late Interrupt system init called from start_kernel for Boot CPU only
  *
  * Since slab must already be initialized, platforms can start doing any
@@ -178,107 +72,3 @@ void arc_request_percpu_irq(int irq, int cpu,
 
 	enable_percpu_irq(irq, 0);
 }
-
-/*
- * arch_local_irq_enable - Enable interrupts.
- *
- * 1. Explicitly called to re-enable interrupts
- * 2. Implicitly called from spin_unlock_irq, write_unlock_irq etc
- *    which maybe in hard ISR itself
- *
- * Semantics of this function change depending on where it is called from:
- *
- * -If called from hard-ISR, it must not invert interrupt priorities
- *  e.g. suppose TIMER is high priority (Level 2) IRQ
- *    Time hard-ISR, timer_interrupt( ) calls spin_unlock_irq several times.
- *    Here local_irq_enable( ) shd not re-enable lower priority interrupts
- * -If called from soft-ISR, it must re-enable all interrupts
- *    soft ISR are low prioity jobs which can be very slow, thus all IRQs
- *    must be enabled while they run.
- *    Now hardware context wise we may still be in L2 ISR (not done rtie)
- *    still we must re-enable both L1 and L2 IRQs
- *  Another twist is prev scenario with flow being
- *     L1 ISR ==> interrupted by L2 ISR  ==> L2 soft ISR
- *     here we must not re-enable Ll as prev Ll Interrupt's h/w context will get
- *     over-written (this is deficiency in ARC700 Interrupt mechanism)
- */
-
-#ifdef CONFIG_ARC_COMPACT_IRQ_LEVELS	/* Complex version for 2 IRQ levels */
-
-void arch_local_irq_enable(void)
-{
-
-	unsigned long flags;
-	flags = arch_local_save_flags();
-
-	/* Allow both L1 and L2 at the onset */
-	flags |= (STATUS_E1_MASK | STATUS_E2_MASK);
-
-	/* Called from hard ISR (between irq_enter and irq_exit) */
-	if (in_irq()) {
-
-		/* If in L2 ISR, don't re-enable any further IRQs as this can
-		 * cause IRQ priorities to get upside down. e.g. it could allow
-		 * L1 be taken while in L2 hard ISR which is wrong not only in
-		 * theory, it can also cause the dreaded L1-L2-L1 scenario
-		 */
-		if (flags & STATUS_A2_MASK)
-			flags &= ~(STATUS_E1_MASK | STATUS_E2_MASK);
-
-		/* Even if in L1 ISR, allowe Higher prio L2 IRQs */
-		else if (flags & STATUS_A1_MASK)
-			flags &= ~(STATUS_E1_MASK);
-	}
-
-	/* called from soft IRQ, ideally we want to re-enable all levels */
-
-	else if (in_softirq()) {
-
-		/* However if this is case of L1 interrupted by L2,
-		 * re-enabling both may cause whaco L1-L2-L1 scenario
-		 * because ARC700 allows level 1 to interrupt an active L2 ISR
-		 * Thus we disable both
-		 * However some code, executing in soft ISR wants some IRQs
-		 * to be enabled so we re-enable L2 only
-		 *
-		 * How do we determine L1 intr by L2
-		 *  -A2 is set (means in L2 ISR)
-		 *  -E1 is set in this ISR's pt_regs->status32 which is
-		 *      saved copy of status32_l2 when l2 ISR happened
-		 */
-		struct pt_regs *pt = get_irq_regs();
-		if ((flags & STATUS_A2_MASK) && pt &&
-		    (pt->status32 & STATUS_A1_MASK)) {
-			/*flags &= ~(STATUS_E1_MASK | STATUS_E2_MASK); */
-			flags &= ~(STATUS_E1_MASK);
-		}
-	}
-
-	arch_local_irq_restore(flags);
-}
-
-#else /* ! CONFIG_ARC_COMPACT_IRQ_LEVELS */
-
-/*
- * Simpler version for only 1 level of interrupt
- * Here we only Worry about Level 1 Bits
- */
-void arch_local_irq_enable(void)
-{
-	unsigned long flags;
-
-	/*
-	 * ARC IDE Drivers tries to re-enable interrupts from hard-isr
-	 * context which is simply wrong
-	 */
-	if (in_irq()) {
-		WARN_ONCE(1, "IRQ enabled from hard-isr");
-		return;
-	}
-
-	flags = arch_local_save_flags();
-	flags |= (STATUS_E1_MASK | STATUS_E2_MASK);
-	arch_local_irq_restore(flags);
-}
-#endif
-EXPORT_SYMBOL(arch_local_irq_enable);