serial: max3107: Abstract out the platform specific bits

At the moment there is only one platform type supported and there is is
hard wired, but with these changes the infrastructure is now there for
anyone else to provide methods for their hardware.

Signed-off-by: Alan Cox <alan@linux.intel.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>

1 files changed, 83 insertions, 2 deletions

diff --git a/drivers/serial/max3107.h b/drivers/serial/max3107.h
index a5625d1f263d..72b30415f417 100644
--- a/drivers/serial/max3107.h
+++ b/drivers/serial/max3107.h
@@ -10,8 +10,8 @@
  * (at your option) any later version.
  */
 
-#ifndef _LINUX_SERIAL_MAX3107_H
-#define _LINUX_SERIAL_MAX3107_H
+#ifndef _MAX3107_H
+#define _MAX3107_H
 
 /* Serial error status definitions */
 #define MAX3107_PARITY_ERROR	1
@@ -355,4 +355,85 @@
 #define MAX3107_BRG13_IB460800	(0x000000 | 0x00)
 #define MAX3107_BRG13_IB921600	(0x000000 | 0x00)
 
+
+struct baud_table {
+	int baud;
+	u32 new_brg;
+};
+
+struct max3107_port {
+	/* UART port structure */
+	struct uart_port port;
+
+	/* SPI device structure */
+	struct spi_device *spi;
+
+	/* GPIO chip stucture */
+	struct gpio_chip chip;
+
+	/* Workqueue that does all the magic */
+	struct workqueue_struct *workqueue;
+	struct work_struct work;
+
+	/* Lock for shared data */
+	spinlock_t data_lock;
+
+	/* Device configuration */
+	int ext_clk;		/* 1 if external clock used */
+	int loopback;		/* Current loopback mode state */
+	int baud;			/* Current baud rate */
+
+	/* State flags */
+	int suspended;		/* Indicates suspend mode */
+	int tx_fifo_empty;	/* Flag for TX FIFO state */
+	int rx_enabled;		/* Flag for receiver state */
+	int tx_enabled;		/* Flag for transmitter state */
+
+	u16 irqen_reg;		/* Current IRQ enable register value */
+	/* Shared data */
+	u16 mode1_reg;		/* Current mode1 register value*/
+	int mode1_commit;	/* Flag for setting new mode1 register value */
+	u16 lcr_reg;		/* Current LCR register value */
+	int lcr_commit;		/* Flag for setting new LCR register value */
+	u32 brg_cfg;		/* Current Baud rate generator config  */
+	int brg_commit;		/* Flag for setting new baud rate generator
+				 * config
+				 */
+	struct baud_table *baud_tbl;
+	int handle_irq;		/* Indicates that IRQ should be handled */
+
+	/* Rx buffer and str*/
+	u16 *rxbuf;
+	u8  *rxstr;
+	/* Tx buffer*/
+	u16 *txbuf;
+
+	struct max3107_plat *pdata;	/* Platform data */
+};
+
+/* Platform data structure */
+struct max3107_plat {
+	/* Loopback mode enable */
+	int loopback;
+	/* External clock enable */
+	int ext_clk;
+	/* Called during the register initialisation */
+	void (*init)(struct max3107_port *s);
+	/* Called when the port is found and configured */
+	int (*configure)(struct max3107_port *s);
+	/* HW suspend function */
+	void (*hw_suspend) (struct max3107_port *s, int suspend);
+	/* Polling mode enable */
+	int polled_mode;
+	/* Polling period if polling mode enabled */
+	int poll_time;
+};
+
+extern int max3107_rw(struct max3107_port *s, u8 *tx, u8 *rx, int len);
+extern void max3107_hw_susp(struct max3107_port *s, int suspend);
+extern int max3107_probe(struct spi_device *spi, struct max3107_plat *pdata);
+extern int max3107_remove(struct spi_device *spi);
+extern int max3107_suspend(struct spi_device *spi, pm_message_t state);
+extern int max3107_resume(struct spi_device *spi);
+
 #endif /* _LINUX_SERIAL_MAX3107_H */