Merge branch 'parisc-4.11-3' of git://git.kernel.org/pub/scm/linux/kernel/git/deller/parisc-linux into uaccess.parisc

1 files changed, 16 insertions, 7 deletions

diff --git a/drivers/gpu/drm/i915/intel_pm.c b/drivers/gpu/drm/i915/intel_pm.c
index 249623d45be0..6a29784d2b41 100644
--- a/drivers/gpu/drm/i915/intel_pm.c
+++ b/drivers/gpu/drm/i915/intel_pm.c
@@ -4891,6 +4891,12 @@ static void gen6_set_rps_thresholds(struct drm_i915_private *dev_priv, u8 val)
 		break;
 	}
 
+	/* When byt can survive without system hang with dynamic
+	 * sw freq adjustments, this restriction can be lifted.
+	 */
+	if (IS_VALLEYVIEW(dev_priv))
+		goto skip_hw_write;
+
 	I915_WRITE(GEN6_RP_UP_EI,
 		   GT_INTERVAL_FROM_US(dev_priv, ei_up));
 	I915_WRITE(GEN6_RP_UP_THRESHOLD,
@@ -4911,6 +4917,7 @@ static void gen6_set_rps_thresholds(struct drm_i915_private *dev_priv, u8 val)
 		   GEN6_RP_UP_BUSY_AVG |
 		   GEN6_RP_DOWN_IDLE_AVG);
 
+skip_hw_write:
 	dev_priv->rps.power = new_power;
 	dev_priv->rps.up_threshold = threshold_up;
 	dev_priv->rps.down_threshold = threshold_down;
@@ -4921,8 +4928,9 @@ static u32 gen6_rps_pm_mask(struct drm_i915_private *dev_priv, u8 val)
 {
 	u32 mask = 0;
 
+	/* We use UP_EI_EXPIRED interupts for both up/down in manual mode */
 	if (val > dev_priv->rps.min_freq_softlimit)
-		mask |= GEN6_PM_RP_DOWN_EI_EXPIRED | GEN6_PM_RP_DOWN_THRESHOLD | GEN6_PM_RP_DOWN_TIMEOUT;
+		mask |= GEN6_PM_RP_UP_EI_EXPIRED | GEN6_PM_RP_DOWN_THRESHOLD | GEN6_PM_RP_DOWN_TIMEOUT;
 	if (val < dev_priv->rps.max_freq_softlimit)
 		mask |= GEN6_PM_RP_UP_EI_EXPIRED | GEN6_PM_RP_UP_THRESHOLD;
 
@@ -5032,7 +5040,7 @@ void gen6_rps_busy(struct drm_i915_private *dev_priv)
 {
 	mutex_lock(&dev_priv->rps.hw_lock);
 	if (dev_priv->rps.enabled) {
-		if (dev_priv->pm_rps_events & (GEN6_PM_RP_DOWN_EI_EXPIRED | GEN6_PM_RP_UP_EI_EXPIRED))
+		if (dev_priv->pm_rps_events & GEN6_PM_RP_UP_EI_EXPIRED)
 			gen6_rps_reset_ei(dev_priv);
 		I915_WRITE(GEN6_PMINTRMSK,
 			   gen6_rps_pm_mask(dev_priv, dev_priv->rps.cur_freq));
@@ -7916,10 +7924,10 @@ static bool skl_pcode_try_request(struct drm_i915_private *dev_priv, u32 mbox,
  * @timeout_base_ms: timeout for polling with preemption enabled
  *
  * Keep resending the @request to @mbox until PCODE acknowledges it, PCODE
- * reports an error or an overall timeout of @timeout_base_ms+10 ms expires.
+ * reports an error or an overall timeout of @timeout_base_ms+50 ms expires.
  * The request is acknowledged once the PCODE reply dword equals @reply after
  * applying @reply_mask. Polling is first attempted with preemption enabled
- * for @timeout_base_ms and if this times out for another 10 ms with
+ * for @timeout_base_ms and if this times out for another 50 ms with
  * preemption disabled.
  *
  * Returns 0 on success, %-ETIMEDOUT in case of a timeout, <0 in case of some
@@ -7955,14 +7963,15 @@ int skl_pcode_request(struct drm_i915_private *dev_priv, u32 mbox, u32 request,
 	 * worst case) _and_ PCODE was busy for some reason even after a
 	 * (queued) request and @timeout_base_ms delay. As a workaround retry
 	 * the poll with preemption disabled to maximize the number of
-	 * requests. Increase the timeout from @timeout_base_ms to 10ms to
+	 * requests. Increase the timeout from @timeout_base_ms to 50ms to
 	 * account for interrupts that could reduce the number of these
-	 * requests.
+	 * requests, and for any quirks of the PCODE firmware that delays
+	 * the request completion.
 	 */
 	DRM_DEBUG_KMS("PCODE timeout, retrying with preemption disabled\n");
 	WARN_ON_ONCE(timeout_base_ms > 3);
 	preempt_disable();
-	ret = wait_for_atomic(COND, 10);
+	ret = wait_for_atomic(COND, 50);
 	preempt_enable();
 
 out: