diff options
Diffstat (limited to 'drivers/usb')
36 files changed, 492 insertions, 155 deletions
diff --git a/drivers/usb/Makefile b/drivers/usb/Makefile index 825bf884537a..8b7ff467d262 100644 --- a/drivers/usb/Makefile +++ b/drivers/usb/Makefile @@ -51,6 +51,7 @@ obj-$(CONFIG_USB_SERIAL) += serial/ obj-$(CONFIG_USB_ADUTUX) += misc/ obj-$(CONFIG_USB_APPLEDISPLAY) += misc/ obj-$(CONFIG_USB_AUERSWALD) += misc/ +obj-$(CONFIG_USB_BERRY_CHARGE) += misc/ obj-$(CONFIG_USB_CYPRESS_CY7C63)+= misc/ obj-$(CONFIG_USB_CYTHERM) += misc/ obj-$(CONFIG_USB_EMI26) += misc/ diff --git a/drivers/usb/atm/ueagle-atm.c b/drivers/usb/atm/ueagle-atm.c index dae4ef1e8fe5..4973e147bc79 100644 --- a/drivers/usb/atm/ueagle-atm.c +++ b/drivers/usb/atm/ueagle-atm.c @@ -61,6 +61,7 @@ #include <linux/usb.h> #include <linux/firmware.h> #include <linux/ctype.h> +#include <linux/sched.h> #include <linux/kthread.h> #include <linux/version.h> #include <linux/mutex.h> diff --git a/drivers/usb/class/cdc-acm.c b/drivers/usb/class/cdc-acm.c index 98199628e394..d38a25f36ea5 100644 --- a/drivers/usb/class/cdc-acm.c +++ b/drivers/usb/class/cdc-acm.c @@ -326,10 +326,16 @@ static void acm_rx_tasklet(unsigned long _acm) struct tty_struct *tty = acm->tty; struct acm_ru *rcv; unsigned long flags; - int i = 0; + unsigned char throttled; dbg("Entering acm_rx_tasklet"); - if (!ACM_READY(acm) || acm->throttle) + if (!ACM_READY(acm)) + return; + + spin_lock(&acm->throttle_lock); + throttled = acm->throttle; + spin_unlock(&acm->throttle_lock); + if (throttled) return; next_buffer: @@ -346,22 +352,20 @@ next_buffer: dbg("acm_rx_tasklet: procesing buf 0x%p, size = %d", buf, buf->size); tty_buffer_request_room(tty, buf->size); - if (!acm->throttle) + spin_lock(&acm->throttle_lock); + throttled = acm->throttle; + spin_unlock(&acm->throttle_lock); + if (!throttled) tty_insert_flip_string(tty, buf->base, buf->size); tty_flip_buffer_push(tty); - spin_lock(&acm->throttle_lock); - if (acm->throttle) { - dbg("Throtteling noticed"); - memmove(buf->base, buf->base + i, buf->size - i); - buf->size -= i; - spin_unlock(&acm->throttle_lock); + if (throttled) { + dbg("Throttling noticed"); spin_lock_irqsave(&acm->read_lock, flags); list_add(&buf->list, &acm->filled_read_bufs); spin_unlock_irqrestore(&acm->read_lock, flags); return; } - spin_unlock(&acm->throttle_lock); spin_lock_irqsave(&acm->read_lock, flags); list_add(&buf->list, &acm->spare_read_bufs); @@ -467,7 +471,8 @@ static int acm_tty_open(struct tty_struct *tty, struct file *filp) goto bail_out; } - if (0 > acm_set_control(acm, acm->ctrlout = ACM_CTRL_DTR | ACM_CTRL_RTS)) + if (0 > acm_set_control(acm, acm->ctrlout = ACM_CTRL_DTR | ACM_CTRL_RTS) && + (acm->ctrl_caps & USB_CDC_CAP_LINE)) goto full_bailout; INIT_LIST_HEAD(&acm->spare_read_urbs); @@ -480,6 +485,8 @@ static int acm_tty_open(struct tty_struct *tty, struct file *filp) list_add(&(acm->rb[i].list), &acm->spare_read_bufs); } + acm->throttle = 0; + tasklet_schedule(&acm->urb_task); done: @@ -1092,6 +1099,10 @@ static struct usb_device_id acm_ids[] = { { USB_DEVICE(0x0ace, 0x1611), /* ZyDAS 56K USB MODEM - new version */ .driver_info = SINGLE_RX_URB, /* firmware bug */ }, + { USB_DEVICE(0x22b8, 0x7000), /* Motorola Q Phone */ + .driver_info = NO_UNION_NORMAL, /* has no union descriptor */ + }, + /* control interfaces with various AT-command sets */ { USB_INTERFACE_INFO(USB_CLASS_COMM, USB_CDC_SUBCLASS_ACM, USB_CDC_ACM_PROTO_AT_V25TER) }, diff --git a/drivers/usb/core/devices.c b/drivers/usb/core/devices.c index a47c30b2d764..aefc7987120d 100644 --- a/drivers/usb/core/devices.c +++ b/drivers/usb/core/devices.c @@ -604,10 +604,6 @@ static unsigned int usb_device_poll(struct file *file, struct poll_table_struct lock_kernel(); if (!st) { st = kmalloc(sizeof(struct usb_device_status), GFP_KERNEL); - if (!st) { - unlock_kernel(); - return POLLIN; - } /* we may have dropped BKL - need to check for having lost the race */ if (file->private_data) { @@ -615,6 +611,11 @@ static unsigned int usb_device_poll(struct file *file, struct poll_table_struct st = file->private_data; goto lost_race; } + /* we haven't lost - check for allocation failure now */ + if (!st) { + unlock_kernel(); + return POLLIN; + } /* * need to prevent the module from being unloaded, since diff --git a/drivers/usb/core/devio.c b/drivers/usb/core/devio.c index 2087766f9e88..274f14f1633e 100644 --- a/drivers/usb/core/devio.c +++ b/drivers/usb/core/devio.c @@ -857,11 +857,11 @@ static int proc_setintf(struct dev_state *ps, void __user *arg) static int proc_setconfig(struct dev_state *ps, void __user *arg) { - unsigned int u; + int u; int status = 0; struct usb_host_config *actconfig; - if (get_user(u, (unsigned int __user *)arg)) + if (get_user(u, (int __user *)arg)) return -EFAULT; actconfig = ps->dev->actconfig; diff --git a/drivers/usb/core/driver.c b/drivers/usb/core/driver.c index 600d1bc8272a..2aded261f42c 100644 --- a/drivers/usb/core/driver.c +++ b/drivers/usb/core/driver.c @@ -743,6 +743,7 @@ EXPORT_SYMBOL_GPL(usb_deregister_device_driver); * usb_register_driver - register a USB interface driver * @new_driver: USB operations for the interface driver * @owner: module owner of this driver. + * @mod_name: module name string * * Registers a USB interface driver with the USB core. The list of * unattached interfaces will be rescanned whenever a new driver is diff --git a/drivers/usb/core/endpoint.c b/drivers/usb/core/endpoint.c index 5e628ae3aec7..e0ec7045e865 100644 --- a/drivers/usb/core/endpoint.c +++ b/drivers/usb/core/endpoint.c @@ -229,7 +229,7 @@ static int init_endpoint_class(void) kref_init(&ep_class->kref); ep_class->class = class_create(THIS_MODULE, "usb_endpoint"); if (IS_ERR(ep_class->class)) { - result = IS_ERR(ep_class->class); + result = PTR_ERR(ep_class->class); goto class_create_error; } diff --git a/drivers/usb/core/generic.c b/drivers/usb/core/generic.c index b531a4fd30c2..9bbcb20e2d94 100644 --- a/drivers/usb/core/generic.c +++ b/drivers/usb/core/generic.c @@ -184,7 +184,7 @@ static void generic_disconnect(struct usb_device *udev) /* if this is only an unbind, not a physical disconnect, then * unconfigure the device */ if (udev->actconfig) - usb_set_configuration(udev, 0); + usb_set_configuration(udev, -1); usb_remove_sysfs_dev_files(udev); } diff --git a/drivers/usb/core/hub.c b/drivers/usb/core/hub.c index 590ec82d0515..50c0db15304a 100644 --- a/drivers/usb/core/hub.c +++ b/drivers/usb/core/hub.c @@ -44,6 +44,7 @@ struct usb_hub { struct usb_hub_status hub; struct usb_port_status port; } *status; /* buffer for status reports */ + struct mutex status_mutex; /* for the status buffer */ int error; /* last reported error */ int nerrors; /* track consecutive errors */ @@ -535,6 +536,7 @@ static int hub_hub_status(struct usb_hub *hub, { int ret; + mutex_lock(&hub->status_mutex); ret = get_hub_status(hub->hdev, &hub->status->hub); if (ret < 0) dev_err (hub->intfdev, @@ -544,6 +546,7 @@ static int hub_hub_status(struct usb_hub *hub, *change = le16_to_cpu(hub->status->hub.wHubChange); ret = 0; } + mutex_unlock(&hub->status_mutex); return ret; } @@ -617,6 +620,7 @@ static int hub_configure(struct usb_hub *hub, ret = -ENOMEM; goto fail; } + mutex_init(&hub->status_mutex); hub->descriptor = kmalloc(sizeof(*hub->descriptor), GFP_KERNEL); if (!hub->descriptor) { @@ -1396,6 +1400,7 @@ static int hub_port_status(struct usb_hub *hub, int port1, { int ret; + mutex_lock(&hub->status_mutex); ret = get_port_status(hub->hdev, port1, &hub->status->port); if (ret < 4) { dev_err (hub->intfdev, @@ -1407,6 +1412,7 @@ static int hub_port_status(struct usb_hub *hub, int port1, *change = le16_to_cpu(hub->status->port.wPortChange); ret = 0; } + mutex_unlock(&hub->status_mutex); return ret; } @@ -1904,6 +1910,7 @@ static int hub_suspend(struct usb_interface *intf, pm_message_t msg) struct usb_hub *hub = usb_get_intfdata (intf); struct usb_device *hdev = hub->hdev; unsigned port1; + int status = 0; /* fail if children aren't already suspended */ for (port1 = 1; port1 <= hdev->maxchild; port1++) { @@ -1927,24 +1934,18 @@ static int hub_suspend(struct usb_interface *intf, pm_message_t msg) dev_dbg(&intf->dev, "%s\n", __FUNCTION__); + /* stop khubd and related activity */ + hub_quiesce(hub); + /* "global suspend" of the downstream HC-to-USB interface */ if (!hdev->parent) { - struct usb_bus *bus = hdev->bus; - if (bus) { - int status = hcd_bus_suspend (bus); - - if (status != 0) { - dev_dbg(&hdev->dev, "'global' suspend %d\n", - status); - return status; - } - } else - return -EOPNOTSUPP; + status = hcd_bus_suspend(hdev->bus); + if (status != 0) { + dev_dbg(&hdev->dev, "'global' suspend %d\n", status); + hub_activate(hub); + } } - - /* stop khubd and related activity */ - hub_quiesce(hub); - return 0; + return status; } static int hub_resume(struct usb_interface *intf) diff --git a/drivers/usb/core/message.c b/drivers/usb/core/message.c index 8aca3574c2b5..74edaea5665d 100644 --- a/drivers/usb/core/message.c +++ b/drivers/usb/core/message.c @@ -1316,6 +1316,14 @@ static void release_interface(struct device *dev) * use this kind of configurability; many devices only have one * configuration. * + * @configuration is the value of the configuration to be installed. + * According to the USB spec (e.g. section 9.1.1.5), configuration values + * must be non-zero; a value of zero indicates that the device in + * unconfigured. However some devices erroneously use 0 as one of their + * configuration values. To help manage such devices, this routine will + * accept @configuration = -1 as indicating the device should be put in + * an unconfigured state. + * * USB device configurations may affect Linux interoperability, * power consumption and the functionality available. For example, * the default configuration is limited to using 100mA of bus power, @@ -1347,10 +1355,15 @@ int usb_set_configuration(struct usb_device *dev, int configuration) struct usb_interface **new_interfaces = NULL; int n, nintf; - for (i = 0; i < dev->descriptor.bNumConfigurations; i++) { - if (dev->config[i].desc.bConfigurationValue == configuration) { - cp = &dev->config[i]; - break; + if (configuration == -1) + configuration = 0; + else { + for (i = 0; i < dev->descriptor.bNumConfigurations; i++) { + if (dev->config[i].desc.bConfigurationValue == + configuration) { + cp = &dev->config[i]; + break; + } } } if ((!cp && configuration != 0)) @@ -1359,6 +1372,7 @@ int usb_set_configuration(struct usb_device *dev, int configuration) /* The USB spec says configuration 0 means unconfigured. * But if a device includes a configuration numbered 0, * we will accept it as a correctly configured state. + * Use -1 if you really want to unconfigure the device. */ if (cp && configuration == 0) dev_warn(&dev->dev, "config 0 descriptor??\n"); diff --git a/drivers/usb/core/otg_whitelist.h b/drivers/usb/core/otg_whitelist.h index 627a5a2fc9cf..7f31a495a25d 100644 --- a/drivers/usb/core/otg_whitelist.h +++ b/drivers/usb/core/otg_whitelist.h @@ -31,7 +31,7 @@ static struct usb_device_id whitelist_table [] = { { USB_DEVICE_INFO(7, 1, 3) }, #endif -#ifdef CONFIG_USB_CDCETHER +#ifdef CONFIG_USB_NET_CDCETHER /* Linux-USB CDC Ethernet gadget */ { USB_DEVICE(0x0525, 0xa4a1), }, /* Linux-USB CDC Ethernet + RNDIS gadget */ diff --git a/drivers/usb/core/sysfs.c b/drivers/usb/core/sysfs.c index 4eaa0ee8e72f..0edfbafd702c 100644 --- a/drivers/usb/core/sysfs.c +++ b/drivers/usb/core/sysfs.c @@ -63,7 +63,7 @@ set_bConfigurationValue(struct device *dev, struct device_attribute *attr, struct usb_device *udev = to_usb_device(dev); int config, value; - if (sscanf(buf, "%u", &config) != 1 || config > 255) + if (sscanf(buf, "%d", &config) != 1 || config < -1 || config > 255) return -EINVAL; usb_lock_device(udev); value = usb_set_configuration(udev, config); diff --git a/drivers/usb/gadget/at91_udc.c b/drivers/usb/gadget/at91_udc.c index 36b36e0175fc..82369c4729b5 100644 --- a/drivers/usb/gadget/at91_udc.c +++ b/drivers/usb/gadget/at91_udc.c @@ -784,7 +784,7 @@ static int at91_ep_set_halt(struct usb_ep *_ep, int value) return status; } -static struct usb_ep_ops at91_ep_ops = { +static const struct usb_ep_ops at91_ep_ops = { .enable = at91_ep_enable, .disable = at91_ep_disable, .alloc_request = at91_ep_alloc_request, @@ -1651,7 +1651,7 @@ static void at91udc_shutdown(struct platform_device *dev) pullup(platform_get_drvdata(dev), 0); } -static int __devinit at91udc_probe(struct platform_device *pdev) +static int __init at91udc_probe(struct platform_device *pdev) { struct device *dev = &pdev->dev; struct at91_udc *udc; @@ -1762,7 +1762,7 @@ fail0: return retval; } -static int __devexit at91udc_remove(struct platform_device *pdev) +static int __exit at91udc_remove(struct platform_device *pdev) { struct at91_udc *udc = platform_get_drvdata(pdev); struct resource *res; @@ -1836,8 +1836,7 @@ static int at91udc_resume(struct platform_device *pdev) #endif static struct platform_driver at91_udc = { - .probe = at91udc_probe, - .remove = __devexit_p(at91udc_remove), + .remove = __exit_p(at91udc_remove), .shutdown = at91udc_shutdown, .suspend = at91udc_suspend, .resume = at91udc_resume, @@ -1847,13 +1846,13 @@ static struct platform_driver at91_udc = { }, }; -static int __devinit udc_init_module(void) +static int __init udc_init_module(void) { - return platform_driver_register(&at91_udc); + return platform_driver_probe(&at91_udc, at91udc_probe); } module_init(udc_init_module); -static void __devexit udc_exit_module(void) +static void __exit udc_exit_module(void) { platform_driver_unregister(&at91_udc); } diff --git a/drivers/usb/gadget/serial.c b/drivers/usb/gadget/serial.c index e6c19aa4bef3..e552668d36b3 100644 --- a/drivers/usb/gadget/serial.c +++ b/drivers/usb/gadget/serial.c @@ -1699,6 +1699,7 @@ static int gs_setup_class(struct usb_gadget *gadget, memcpy(&port->port_line_coding, req->buf, ret); spin_unlock(&port->port_lock); } + ret = 0; break; case USB_CDC_REQ_GET_LINE_CODING: diff --git a/drivers/usb/host/ehci-hcd.c b/drivers/usb/host/ehci-hcd.c index 185721dba42b..a74056488234 100644 --- a/drivers/usb/host/ehci-hcd.c +++ b/drivers/usb/host/ehci-hcd.c @@ -42,6 +42,9 @@ #include <asm/irq.h> #include <asm/system.h> #include <asm/unaligned.h> +#ifdef CONFIG_PPC_PS3 +#include <asm/firmware.h> +#endif /*-------------------------------------------------------------------------*/ @@ -299,6 +302,19 @@ static void ehci_watchdog (unsigned long param) spin_unlock_irqrestore (&ehci->lock, flags); } +/* On some systems, leaving remote wakeup enabled prevents system shutdown. + * The firmware seems to think that powering off is a wakeup event! + * This routine turns off remote wakeup and everything else, on all ports. + */ +static void ehci_turn_off_all_ports(struct ehci_hcd *ehci) +{ + int port = HCS_N_PORTS(ehci->hcs_params); + + while (port--) + ehci_writel(ehci, PORT_RWC_BITS, + &ehci->regs->port_status[port]); +} + /* ehci_shutdown kick in for silicon on any bus (not just pci, etc). * This forcibly disables dma and IRQs, helping kexec and other cases * where the next system software may expect clean state. @@ -310,9 +326,13 @@ ehci_shutdown (struct usb_hcd *hcd) ehci = hcd_to_ehci (hcd); (void) ehci_halt (ehci); + ehci_turn_off_all_ports(ehci); /* make BIOS/etc use companion controller during reboot */ ehci_writel(ehci, 0, &ehci->regs->configured_flag); + + /* unblock posted writes */ + ehci_readl(ehci, &ehci->regs->configured_flag); } static void ehci_port_power (struct ehci_hcd *ehci, int is_on) @@ -951,15 +971,18 @@ static int __init ehci_hcd_init(void) #endif #ifdef PS3_SYSTEM_BUS_DRIVER - retval = ps3_system_bus_driver_register(&PS3_SYSTEM_BUS_DRIVER); - if (retval < 0) { + if (firmware_has_feature(FW_FEATURE_PS3_LV1)) { + retval = ps3_system_bus_driver_register( + &PS3_SYSTEM_BUS_DRIVER); + if (retval < 0) { #ifdef PLATFORM_DRIVER - platform_driver_unregister(&PLATFORM_DRIVER); + platform_driver_unregister(&PLATFORM_DRIVER); #endif #ifdef PCI_DRIVER - pci_unregister_driver(&PCI_DRIVER); + pci_unregister_driver(&PCI_DRIVER); #endif - return retval; + return retval; + } } #endif @@ -976,7 +999,8 @@ static void __exit ehci_hcd_cleanup(void) pci_unregister_driver(&PCI_DRIVER); #endif #ifdef PS3_SYSTEM_BUS_DRIVER - ps3_system_bus_driver_unregister(&PS3_SYSTEM_BUS_DRIVER); + if (firmware_has_feature(FW_FEATURE_PS3_LV1)) + ps3_system_bus_driver_unregister(&PS3_SYSTEM_BUS_DRIVER); #endif } module_exit(ehci_hcd_cleanup); diff --git a/drivers/usb/host/ehci-hub.c b/drivers/usb/host/ehci-hub.c index 0d83c6df1a3b..9af529d22b3e 100644 --- a/drivers/usb/host/ehci-hub.c +++ b/drivers/usb/host/ehci-hub.c @@ -36,6 +36,8 @@ static int ehci_bus_suspend (struct usb_hcd *hcd) int port; int mask; + ehci_dbg(ehci, "suspend root hub\n"); + if (time_before (jiffies, ehci->next_statechange)) msleep(5); diff --git a/drivers/usb/host/isp116x-hcd.c b/drivers/usb/host/isp116x-hcd.c index 2718b5dc4ec1..46873f2534b5 100644 --- a/drivers/usb/host/isp116x-hcd.c +++ b/drivers/usb/host/isp116x-hcd.c @@ -1577,7 +1577,7 @@ static int isp116x_remove(struct platform_device *pdev) #define resource_len(r) (((r)->end - (r)->start) + 1) -static int __init isp116x_probe(struct platform_device *pdev) +static int __devinit isp116x_probe(struct platform_device *pdev) { struct usb_hcd *hcd; struct isp116x *isp116x; diff --git a/drivers/usb/host/ohci-at91.c b/drivers/usb/host/ohci-at91.c index 930346487278..d849c809acbd 100644 --- a/drivers/usb/host/ohci-at91.c +++ b/drivers/usb/host/ohci-at91.c @@ -18,19 +18,38 @@ #include <asm/mach-types.h> #include <asm/hardware.h> #include <asm/arch/board.h> +#include <asm/arch/cpu.h> #ifndef CONFIG_ARCH_AT91 #error "CONFIG_ARCH_AT91 must be defined." #endif -/* interface and function clocks */ -static struct clk *iclk, *fclk; +/* interface and function clocks; sometimes also an AHB clock */ +static struct clk *iclk, *fclk, *hclk; static int clocked; extern int usb_disabled(void); /*-------------------------------------------------------------------------*/ +static void at91_start_clock(void) +{ + if (cpu_is_at91sam9261()) + clk_enable(hclk); + clk_enable(iclk); + clk_enable(fclk); + clocked = 1; +} + +static void at91_stop_clock(void) +{ + clk_disable(fclk); + clk_disable(iclk); + if (cpu_is_at91sam9261()) + clk_disable(hclk); + clocked = 0; +} + static void at91_start_hc(struct platform_device *pdev) { struct usb_hcd *hcd = platform_get_drvdata(pdev); @@ -41,9 +60,7 @@ static void at91_start_hc(struct platform_device *pdev) /* * Start the USB clocks. */ - clk_enable(iclk); - clk_enable(fclk); - clocked = 1; + at91_start_clock(); /* * The USB host controller must remain in reset. @@ -66,9 +83,7 @@ static void at91_stop_hc(struct platform_device *pdev) /* * Stop the USB clocks. */ - clk_disable(fclk); - clk_disable(iclk); - clocked = 0; + at91_stop_clock(); } @@ -126,6 +141,8 @@ static int usb_hcd_at91_probe(const struct hc_driver *driver, iclk = clk_get(&pdev->dev, "ohci_clk"); fclk = clk_get(&pdev->dev, "uhpck"); + if (cpu_is_at91sam9261()) + hclk = clk_get(&pdev->dev, "hck0"); at91_start_hc(pdev); ohci_hcd_init(hcd_to_ohci(hcd)); @@ -137,6 +154,8 @@ static int usb_hcd_at91_probe(const struct hc_driver *driver, /* Error handling */ at91_stop_hc(pdev); + if (cpu_is_at91sam9261()) + clk_put(hclk); clk_put(fclk); clk_put(iclk); @@ -171,9 +190,11 @@ static int usb_hcd_at91_remove(struct usb_hcd *hcd, iounmap(hcd->regs); release_mem_region(hcd->rsrc_start, hcd->rsrc_len); + if (cpu_is_at91sam9261()) + clk_put(hclk); clk_put(fclk); clk_put(iclk); - fclk = iclk = NULL; + fclk = iclk = hclk = NULL; dev_set_drvdata(&pdev->dev, NULL); return 0; @@ -280,9 +301,7 @@ ohci_hcd_at91_drv_suspend(struct platform_device *pdev, pm_message_t mesg) */ if (at91_suspend_entering_slow_clock()) { ohci_usb_reset (ohci); - clk_disable(fclk); - clk_disable(iclk); - clocked = 0; + at91_stop_clock(); } return 0; @@ -295,11 +314,8 @@ static int ohci_hcd_at91_drv_resume(struct platform_device *pdev) if (device_may_wakeup(&pdev->dev)) disable_irq_wake(hcd->irq); - if (!clocked) { - clk_enable(iclk); - clk_enable(fclk); - clocked = 1; - } + if (!clocked) + at91_start_clock(); return 0; } diff --git a/drivers/usb/host/ohci-hcd.c b/drivers/usb/host/ohci-hcd.c index fa6a7ceaa0db..f0d29eda3c6d 100644 --- a/drivers/usb/host/ohci-hcd.c +++ b/drivers/usb/host/ohci-hcd.c @@ -42,6 +42,9 @@ #include <asm/system.h> #include <asm/unaligned.h> #include <asm/byteorder.h> +#ifdef CONFIG_PPC_PS3 +#include <asm/firmware.h> +#endif #include "../core/hcd.h" @@ -944,9 +947,12 @@ static int __init ohci_hcd_mod_init(void) sizeof (struct ed), sizeof (struct td)); #ifdef PS3_SYSTEM_BUS_DRIVER - retval = ps3_system_bus_driver_register(&PS3_SYSTEM_BUS_DRIVER); - if (retval < 0) - goto error_ps3; + if (firmware_has_feature(FW_FEATURE_PS3_LV1)) { + retval = ps3_system_bus_driver_register( + &PS3_SYSTEM_BUS_DRIVER); + if (retval < 0) + goto error_ps3; + } #endif #ifdef PLATFORM_DRIVER @@ -992,7 +998,8 @@ static int __init ohci_hcd_mod_init(void) error_platform: #endif #ifdef PS3_SYSTEM_BUS_DRIVER - ps3_system_bus_driver_unregister(&PS3_SYSTEM_BUS_DRIVER); + if (firmware_has_feature(FW_FEATURE_PS3_LV1)) + ps3_system_bus_driver_unregister(&PS3_SYSTEM_BUS_DRIVER); error_ps3: #endif return retval; @@ -1014,7 +1021,8 @@ static void __exit ohci_hcd_mod_exit(void) platform_driver_unregister(&PLATFORM_DRIVER); #endif #ifdef PS3_SYSTEM_BUS_DRIVER - ps3_system_bus_driver_unregister(&PS3_SYSTEM_BUS_DRIVER); + if (firmware_has_feature(FW_FEATURE_PS3_LV1)) + ps3_system_bus_driver_unregister(&PS3_SYSTEM_BUS_DRIVER); #endif } module_exit(ohci_hcd_mod_exit); diff --git a/drivers/usb/input/hid-core.c b/drivers/usb/input/hid-core.c index 4d8ed3d71a15..ef09952f2039 100644 --- a/drivers/usb/input/hid-core.c +++ b/drivers/usb/input/hid-core.c @@ -515,6 +515,7 @@ void usbhid_close(struct hid_device *hid) #define USB_VENDOR_ID_TURBOX 0x062a #define USB_DEVICE_ID_TURBOX_KEYBOARD 0x0201 +#define USB_VENDOR_ID_CIDC 0x1677 /* * Initialize all reports @@ -548,7 +549,6 @@ void usbhid_init_reports(struct hid_device *hid) } #define USB_VENDOR_ID_GTCO 0x078c -#define USB_VENDOR_ID_GTCO_IPANEL_2 0x5543 #define USB_DEVICE_ID_GTCO_90 0x0090 #define USB_DEVICE_ID_GTCO_100 0x0100 #define USB_DEVICE_ID_GTCO_101 0x0101 @@ -594,8 +594,6 @@ void usbhid_init_reports(struct hid_device *hid) #define USB_DEVICE_ID_GTCO_1004 0x1004 #define USB_DEVICE_ID_GTCO_1005 0x1005 #define USB_DEVICE_ID_GTCO_1006 0x1006 -#define USB_DEVICE_ID_GTCO_8 0x0008 -#define USB_DEVICE_ID_GTCO_d 0x000d #define USB_VENDOR_ID_WACOM 0x056a @@ -854,8 +852,6 @@ static const struct hid_blacklist { { USB_VENDOR_ID_GTCO, USB_DEVICE_ID_GTCO_1004, HID_QUIRK_IGNORE }, { USB_VENDOR_ID_GTCO, USB_DEVICE_ID_GTCO_1005, HID_QUIRK_IGNORE }, { USB_VENDOR_ID_GTCO, USB_DEVICE_ID_GTCO_1006, HID_QUIRK_IGNORE }, - { USB_VENDOR_ID_GTCO_IPANEL_2, USB_DEVICE_ID_GTCO_8, HID_QUIRK_IGNORE }, - { USB_VENDOR_ID_GTCO_IPANEL_2, USB_DEVICE_ID_GTCO_d, HID_QUIRK_IGNORE }, { USB_VENDOR_ID_IMATION, USB_DEVICE_ID_DISC_STAKKA, HID_QUIRK_IGNORE }, { USB_VENDOR_ID_KBGEAR, USB_DEVICE_ID_KBGEAR_JAMSTUDIO, HID_QUIRK_IGNORE }, { USB_VENDOR_ID_LD, USB_DEVICE_ID_LD_CASSY, HID_QUIRK_IGNORE }, @@ -953,6 +949,8 @@ static const struct hid_blacklist { { USB_VENDOR_ID_SONY, USB_DEVICE_ID_SONY_PS3_CONTROLLER, HID_QUIRK_SONY_PS3_CONTROLLER }, + { USB_VENDOR_ID_CIDC, 0x0103, HID_QUIRK_IGNORE }, + { 0, 0 } }; diff --git a/drivers/usb/misc/Kconfig b/drivers/usb/misc/Kconfig index a74bf8617e7f..4907e8b80070 100644 --- a/drivers/usb/misc/Kconfig +++ b/drivers/usb/misc/Kconfig @@ -88,6 +88,17 @@ config USB_LCD To compile this driver as a module, choose M here: the module will be called usblcd. +config USB_BERRY_CHARGE + tristate "USB BlackBerry recharge support" + depends on USB + help + Say Y here if you want to connect a BlackBerry device to your + computer's USB port and have it automatically switch to "recharge" + mode. + + To compile this driver as a module, choose M here: the + module will be called berry_charge. + config USB_LED tristate "USB LED driver support" depends on USB diff --git a/drivers/usb/misc/Makefile b/drivers/usb/misc/Makefile index 2cba07d31971..dac2d5b71566 100644 --- a/drivers/usb/misc/Makefile +++ b/drivers/usb/misc/Makefile @@ -6,6 +6,7 @@ obj-$(CONFIG_USB_ADUTUX) += adutux.o obj-$(CONFIG_USB_APPLEDISPLAY) += appledisplay.o obj-$(CONFIG_USB_AUERSWALD) += auerswald.o +obj-$(CONFIG_USB_BERRY_CHARGE) += berry_charge.o obj-$(CONFIG_USB_CYPRESS_CY7C63)+= cypress_cy7c63.o obj-$(CONFIG_USB_CYTHERM) += cytherm.o obj-$(CONFIG_USB_EMI26) += emi26.o diff --git a/drivers/usb/misc/berry_charge.c b/drivers/usb/misc/berry_charge.c new file mode 100644 index 000000000000..60893c6c8221 --- /dev/null +++ b/drivers/usb/misc/berry_charge.c @@ -0,0 +1,140 @@ +/* + * USB BlackBerry charging module + * + * Copyright (C) 2007 Greg Kroah-Hartman <gregkh@suse.de> + * + * This program is free software; you can redistribute it and/or + * modify it under the terms of the GNU General Public License as + * published by the Free Software Foundation, version 2. + * + * Information on how to switch configs was taken by the bcharge.cc file + * created by the barry.sf.net project. + * + * bcharge.cc has the following copyright: + * Copyright (C) 2006, Net Direct Inc. (http://www.netdirect.ca/) + * and is released under the GPLv2. + * + * + */ + +#include <linux/kernel.h> +#include <linux/errno.h> +#include <linux/init.h> +#include <linux/slab.h> +#include <linux/module.h> +#include <linux/usb.h> + +#define RIM_VENDOR 0x0fca +#define BLACKBERRY 0x0001 + +static int debug; + +#ifdef dbg +#undef dbg +#endif +#define dbg(dev, format, arg...) \ + if (debug) \ + dev_printk(KERN_DEBUG , dev , format , ## arg) + +static struct usb_device_id id_table [] = { + { USB_DEVICE(RIM_VENDOR, BLACKBERRY) }, + { }, /* Terminating entry */ +}; +MODULE_DEVICE_TABLE(usb, id_table); + +static int magic_charge(struct usb_device *udev) +{ + char *dummy_buffer = kzalloc(2, GFP_KERNEL); + int retval; + + if (!dummy_buffer) + return -ENOMEM; + + /* send two magic commands and then set the configuration. The device + * will then reset itself with the new power usage and should start + * charging. */ + + /* Note, with testing, it only seems that the first message is really + * needed (at least for the 8700c), but to be safe, we emulate what + * other operating systems seem to be sending to their device. We + * really need to get some specs for this device to be sure about what + * is going on here. + */ + dbg(&udev->dev, "Sending first magic command\n"); + retval = usb_control_msg(udev, usb_rcvctrlpipe(udev, 0), + 0xa5, 0xc0, 0, 1, dummy_buffer, 2, 100); + if (retval != 2) { + dev_err(&udev->dev, "First magic command failed: %d.\n", + retval); + return retval; + } + + dbg(&udev->dev, "Sending first magic command\n"); + retval = usb_control_msg(udev, usb_rcvctrlpipe(udev, 0), + 0xa2, 0x40, 0, 1, dummy_buffer, 0, 100); + if (retval != 0) { + dev_err(&udev->dev, "Second magic command failed: %d.\n", + retval); + return retval; + } + + dbg(&udev->dev, "Calling set_configuration\n"); + retval = usb_driver_set_configuration(udev, 1); + if (retval) + dev_err(&udev->dev, "Set Configuration failed :%d.\n", retval); + + return retval; +} + +static int berry_probe(struct usb_interface *intf, + const struct usb_device_id *id) +{ + struct usb_device *udev = interface_to_usbdev(intf); + + dbg(&udev->dev, "Power is set to %dmA\n", + udev->actconfig->desc.bMaxPower * 2); + + /* check the power usage so we don't try to enable something that is + * already enabled */ + if ((udev->actconfig->desc.bMaxPower * 2) == 500) { + dbg(&udev->dev, "device is already charging, power is " + "set to %dmA\n", udev->actconfig->desc.bMaxPower * 2); + return -ENODEV; + } + + /* turn the power on */ + magic_charge(udev); + + /* we don't really want to bind to the device, userspace programs can + * handle the syncing just fine, so get outta here. */ + return -ENODEV; +} + +static void berry_disconnect(struct usb_interface *intf) +{ +} + +static struct usb_driver berry_driver = { + .name = "berry_charge", + .probe = berry_probe, + .disconnect = berry_disconnect, + .id_table = id_table, +}; + +static int __init berry_init(void) +{ + return usb_register(&berry_driver); +} + +static void __exit berry_exit(void) +{ + usb_deregister(&berry_driver); +} + +module_init(berry_init); +module_exit(berry_exit); + +MODULE_LICENSE("GPL"); +MODULE_AUTHOR("Greg Kroah-Hartman <gregkh@suse.de>"); +module_param(debug, bool, S_IRUGO | S_IWUSR); +MODULE_PARM_DESC(debug, "Debug enabled or not"); diff --git a/drivers/usb/net/Kconfig b/drivers/usb/net/Kconfig index a2b94ef512bc..0f3d7dbb537f 100644 --- a/drivers/usb/net/Kconfig +++ b/drivers/usb/net/Kconfig @@ -84,6 +84,7 @@ config USB_PEGASUS config USB_RTL8150 tristate "USB RTL8150 based ethernet device support (EXPERIMENTAL)" depends on EXPERIMENTAL + select MII help Say Y here if you have RTL8150 based usb-ethernet adapter. Send me <petkan@users.sourceforge.net> any comments you may have. @@ -98,7 +99,7 @@ config USB_USBNET_MII config USB_USBNET tristate "Multi-purpose USB Networking Framework" - select MII if USBNET_MII != n + select MII if USB_USBNET_MII != n ---help--- This driver supports several kinds of network links over USB, with "minidrivers" built around a common network driver core @@ -239,6 +240,7 @@ config USB_NET_RNDIS_HOST config USB_NET_CDC_SUBSET tristate "Simple USB Network Links (CDC Ethernet subset)" depends on USB_USBNET + default y help This driver module supports USB network devices that can work without any device-specific information. Select it if you have @@ -298,6 +300,13 @@ config USB_EPSON2888 Choose this option to support the usb networking links used by some sample firmware from Epson. +config USB_KC2190 + boolean "KT Technology KC2190 based cables (InstaNet)" + depends on USB_NET_CDC_SUBSET && EXPERIMENTAL + help + Choose this option if you're using a host-to-host cable + with one of these chips. + config USB_NET_ZAURUS tristate "Sharp Zaurus (stock ROMs) and compatible" depends on USB_USBNET diff --git a/drivers/usb/net/asix.c b/drivers/usb/net/asix.c index bd357e178e55..7ef2e4b5e39b 100644 --- a/drivers/usb/net/asix.c +++ b/drivers/usb/net/asix.c @@ -351,9 +351,11 @@ static struct sk_buff *asix_tx_fixup(struct usbnet *dev, struct sk_buff *skb, skb_push(skb, 4); packet_len = (((skb->len - 4) ^ 0x0000ffff) << 16) + (skb->len - 4); + cpu_to_le32s(&packet_len); memcpy(skb->data, &packet_len, sizeof(packet_len)); if ((skb->len % 512) == 0) { + cpu_to_le32s(&padbytes); memcpy( skb->tail, &padbytes, sizeof(padbytes)); skb_put(skb, sizeof(padbytes)); } diff --git a/drivers/usb/net/cdc_subset.c b/drivers/usb/net/cdc_subset.c index ae8fb06cf38e..bc62b012602b 100644 --- a/drivers/usb/net/cdc_subset.c +++ b/drivers/usb/net/cdc_subset.c @@ -79,13 +79,19 @@ static int always_connected (struct usbnet *dev) * * ALi M5632 driver ... does high speed * + * NOTE that the MS-Windows drivers for this chip use some funky and + * (naturally) undocumented 7-byte prefix to each packet, so this is a + * case where we don't currently interoperate. Also, once you unplug + * one end of the cable, you need to replug the other end too ... since + * chip docs are unavailable, there's no way to reset the relevant state + * short of a power cycle. + * *-------------------------------------------------------------------------*/ static const struct driver_info ali_m5632_info = { .description = "ALi M5632", }; - #endif @@ -159,6 +165,11 @@ static const struct driver_info epson2888_info = { #endif /* CONFIG_USB_EPSON2888 */ +/*------------------------------------------------------------------------- + * + * info from Jonathan McDowell <noodles@earth.li> + * + *-------------------------------------------------------------------------*/ #ifdef CONFIG_USB_KC2190 #define HAVE_HARDWARE static const struct driver_info kc2190_info = { @@ -223,6 +234,10 @@ static const struct usb_device_id products [] = { USB_DEVICE (0x0402, 0x5632), // ALi defaults .driver_info = (unsigned long) &ali_m5632_info, }, +{ + USB_DEVICE (0x182d,0x207c), // SiteCom CN-124 + .driver_info = (unsigned long) &ali_m5632_info, +}, #endif #ifdef CONFIG_USB_AN2720 @@ -314,13 +329,13 @@ static struct usb_driver cdc_subset_driver = { static int __init cdc_subset_init(void) { - return usb_register(&cdc_subset_driver); + return usb_register(&cdc_subset_driver); } module_init(cdc_subset_init); static void __exit cdc_subset_exit(void) { - usb_deregister(&cdc_subset_driver); + usb_deregister(&cdc_subset_driver); } module_exit(cdc_subset_exit); diff --git a/drivers/usb/net/usbnet.c b/drivers/usb/net/usbnet.c index 43ba61abfcc5..de69b183bd2f 100644 --- a/drivers/usb/net/usbnet.c +++ b/drivers/usb/net/usbnet.c @@ -147,7 +147,7 @@ int usbnet_get_endpoints(struct usbnet *dev, struct usb_interface *intf) if (tmp < 0) return tmp; } - + dev->in = usb_rcvbulkpipe (dev->udev, in->desc.bEndpointAddress & USB_ENDPOINT_NUMBER_MASK); dev->out = usb_sndbulkpipe (dev->udev, @@ -327,7 +327,7 @@ static void rx_submit (struct usbnet *dev, struct urb *urb, gfp_t flags) if (netif_running (dev->net) && netif_device_present (dev->net) && !test_bit (EVENT_RX_HALT, &dev->flags)) { - switch (retval = usb_submit_urb (urb, GFP_ATOMIC)){ + switch (retval = usb_submit_urb (urb, GFP_ATOMIC)){ case -EPIPE: usbnet_defer_kevent (dev, EVENT_RX_HALT); break; @@ -443,7 +443,7 @@ block: case -EOVERFLOW: dev->stats.rx_over_errors++; // FALLTHROUGH - + default: entry->state = rx_cleanup; dev->stats.rx_errors++; @@ -560,7 +560,7 @@ static int usbnet_stop (struct net_device *net) if (netif_msg_ifdown (dev)) devinfo (dev, "stop stats: rx/tx %ld/%ld, errs %ld/%ld", - dev->stats.rx_packets, dev->stats.tx_packets, + dev->stats.rx_packets, dev->stats.tx_packets, dev->stats.rx_errors, dev->stats.tx_errors ); @@ -578,7 +578,7 @@ static int usbnet_stop (struct net_device *net) devdbg (dev, "waited for %d urb completions", temp); } dev->wait = NULL; - remove_wait_queue (&unlink_wakeup, &wait); + remove_wait_queue (&unlink_wakeup, &wait); usb_kill_urb(dev->interrupt); @@ -834,7 +834,7 @@ kevent (struct work_struct *work) } if (test_bit (EVENT_LINK_RESET, &dev->flags)) { - struct driver_info *info = dev->driver_info; + struct driver_info *info = dev->driver_info; int retval = 0; clear_bit (EVENT_LINK_RESET, &dev->flags); @@ -1066,7 +1066,7 @@ static void usbnet_bh (unsigned long param) * USB Device Driver support * *-------------------------------------------------------------------------*/ - + // precondition: never called in_interrupt void usbnet_disconnect (struct usb_interface *intf) @@ -1087,7 +1087,7 @@ void usbnet_disconnect (struct usb_interface *intf) intf->dev.driver->name, xdev->bus->bus_name, xdev->devpath, dev->driver_info->description); - + net = dev->net; unregister_netdev (net); @@ -1111,7 +1111,7 @@ int usbnet_probe (struct usb_interface *udev, const struct usb_device_id *prod) { struct usbnet *dev; - struct net_device *net; + struct net_device *net; struct usb_host_interface *interface; struct driver_info *info; struct usb_device *xdev; @@ -1181,6 +1181,9 @@ usbnet_probe (struct usb_interface *udev, const struct usb_device_id *prod) // NOTE net->name still not usable ... if (info->bind) { status = info->bind (dev, udev); + if (status < 0) + goto out1; + // heuristic: "usb%d" for links we know are two-host, // else "eth%d" when there's reasonable doubt. userspace // can rename the link if it knows better. @@ -1207,12 +1210,12 @@ usbnet_probe (struct usb_interface *udev, const struct usb_device_id *prod) if (status == 0 && dev->status) status = init_status (dev, udev); if (status < 0) - goto out1; + goto out3; if (!dev->rx_urb_size) dev->rx_urb_size = dev->hard_mtu; dev->maxpacket = usb_maxpacket (dev->udev, dev->out, 1); - + SET_NETDEV_DEV(net, &udev->dev); status = register_netdev (net); if (status) @@ -1255,7 +1258,7 @@ EXPORT_SYMBOL_GPL(usbnet_probe); int usbnet_suspend (struct usb_interface *intf, pm_message_t message) { struct usbnet *dev = usb_get_intfdata(intf); - + /* accelerate emptying of the rx and queues, to avoid * having everything error out. */ @@ -1286,7 +1289,7 @@ static int __init usbnet_init(void) < sizeof (struct skb_data)); random_ether_addr(node_id); - return 0; + return 0; } module_init(usbnet_init); diff --git a/drivers/usb/serial/airprime.c b/drivers/usb/serial/airprime.c index 0af42e32fa0a..18816bf96a4d 100644 --- a/drivers/usb/serial/airprime.c +++ b/drivers/usb/serial/airprime.c @@ -58,11 +58,6 @@ static void airprime_read_bulk_callback(struct urb *urb) if (urb->status) { dbg("%s - nonzero read bulk status received: %d", __FUNCTION__, urb->status); - /* something happened, so free up the memory for this urb */ - if (urb->transfer_buffer) { - kfree (urb->transfer_buffer); - urb->transfer_buffer = NULL; - } return; } usb_serial_debug_data(debug, &port->dev, __FUNCTION__, urb->actual_length, data); @@ -146,6 +141,8 @@ static int airprime_open(struct usb_serial_port *port, struct file *filp) airprime_read_bulk_callback, port); result = usb_submit_urb(urb, GFP_KERNEL); if (result) { + usb_free_urb(urb); + kfree(buffer); dev_err(&port->dev, "%s - failed submitting read urb %d for port %d, error %d\n", __FUNCTION__, i, port->number, result); @@ -160,27 +157,12 @@ static int airprime_open(struct usb_serial_port *port, struct file *filp) /* some error happened, cancel any submitted urbs and clean up anything that got allocated successfully */ - for ( ; i >= 0; --i) { + while (i-- != 0) { urb = priv->read_urbp[i]; - if (urb) { - /* This urb was submitted successfully. So we have to - cancel it. - Unlinking the urb will invoke read_bulk_callback() - with an error status, so its transfer buffer will - be freed there */ - if (usb_unlink_urb (urb) != -EINPROGRESS) { - /* comments in drivers/usb/core/urb.c say this - can only happen if the urb was never submitted, - or has completed already. - Either way we may have to free the transfer - buffer here. */ - if (urb->transfer_buffer) { - kfree (urb->transfer_buffer); - urb->transfer_buffer = NULL; - } - } - usb_free_urb (urb); - } + buffer = urb->transfer_buffer; + usb_kill_urb (urb); + usb_free_urb (urb); + kfree (buffer); } out: @@ -194,10 +176,9 @@ static void airprime_close(struct usb_serial_port *port, struct file * filp) dbg("%s - port %d", __FUNCTION__, port->number); - /* killing the urb will invoke read_bulk_callback() with an error status, - so the transfer buffer will be freed there */ for (i = 0; i < NUM_READ_URBS; ++i) { usb_kill_urb (priv->read_urbp[i]); + kfree (priv->read_urbp[i]->transfer_buffer); usb_free_urb (priv->read_urbp[i]); } diff --git a/drivers/usb/serial/cp2101.c b/drivers/usb/serial/cp2101.c index 3ec24870bca9..db623e754899 100644 --- a/drivers/usb/serial/cp2101.c +++ b/drivers/usb/serial/cp2101.c @@ -69,6 +69,7 @@ static struct usb_device_id id_table [] = { { USB_DEVICE(0x10C4, 0x8218) }, /* Lipowsky Industrie Elektronik GmbH, HARP-1 */ { USB_DEVICE(0x10C4, 0xEA60) }, /* Silicon Labs factory default */ { USB_DEVICE(0x10C4, 0xEA61) }, /* Silicon Labs factory default */ + { USB_DEVICE(0x10C5, 0xEA61) }, /* Silicon Labs MobiData GPRS USB Modem */ { USB_DEVICE(0x13AD, 0x9999) }, /* Baltech card reader */ { USB_DEVICE(0x16D6, 0x0001) }, /* Jablotron serial interface */ { } /* Terminating Entry */ diff --git a/drivers/usb/serial/generic.c b/drivers/usb/serial/generic.c index 601e0648dec6..53baeec8f265 100644 --- a/drivers/usb/serial/generic.c +++ b/drivers/usb/serial/generic.c @@ -66,6 +66,8 @@ struct usb_serial_driver usb_serial_generic_device = { .num_bulk_out = NUM_DONT_CARE, .num_ports = 1, .shutdown = usb_serial_generic_shutdown, + .throttle = usb_serial_generic_throttle, + .unthrottle = usb_serial_generic_unthrottle, }; static int generic_probe(struct usb_interface *interface, @@ -115,6 +117,7 @@ int usb_serial_generic_open (struct usb_serial_port *port, struct file *filp) { struct usb_serial *serial = port->serial; int result = 0; + unsigned long flags; dbg("%s - port %d", __FUNCTION__, port->number); @@ -124,7 +127,13 @@ int usb_serial_generic_open (struct usb_serial_port *port, struct file *filp) if (port->tty) port->tty->low_latency = 1; - /* if we have a bulk interrupt, start reading from it */ + /* clear the throttle flags */ + spin_lock_irqsave(&port->lock, flags); + port->throttled = 0; + port->throttle_req = 0; + spin_unlock_irqrestore(&port->lock, flags); + + /* if we have a bulk endpoint, start reading from it */ if (serial->num_bulk_in) { /* Start reading from the device */ usb_fill_bulk_urb (port->read_urb, serial->dev, @@ -253,31 +262,22 @@ int usb_serial_generic_chars_in_buffer (struct usb_serial_port *port) return (chars); } -void usb_serial_generic_read_bulk_callback (struct urb *urb) +/* Push data to tty layer and resubmit the bulk read URB */ +static void flush_and_resubmit_read_urb (struct usb_serial_port *port) { - struct usb_serial_port *port = (struct usb_serial_port *)urb->context; struct usb_serial *serial = port->serial; - struct tty_struct *tty; - unsigned char *data = urb->transfer_buffer; + struct urb *urb = port->read_urb; + struct tty_struct *tty = port->tty; int result; - dbg("%s - port %d", __FUNCTION__, port->number); - - if (urb->status) { - dbg("%s - nonzero read bulk status received: %d", __FUNCTION__, urb->status); - return; - } - - usb_serial_debug_data(debug, &port->dev, __FUNCTION__, urb->actual_length, data); - - tty = port->tty; + /* Push data to tty */ if (tty && urb->actual_length) { tty_buffer_request_room(tty, urb->actual_length); - tty_insert_flip_string(tty, data, urb->actual_length); - tty_flip_buffer_push(tty); + tty_insert_flip_string(tty, urb->transfer_buffer, urb->actual_length); + tty_flip_buffer_push(tty); /* is this allowed from an URB callback ? */ } - /* Continue trying to always read */ + /* Continue reading from device */ usb_fill_bulk_urb (port->read_urb, serial->dev, usb_rcvbulkpipe (serial->dev, port->bulk_in_endpointAddress), @@ -290,6 +290,40 @@ void usb_serial_generic_read_bulk_callback (struct urb *urb) if (result) dev_err(&port->dev, "%s - failed resubmitting read urb, error %d\n", __FUNCTION__, result); } + +void usb_serial_generic_read_bulk_callback (struct urb *urb) +{ + struct usb_serial_port *port = (struct usb_serial_port *)urb->context; + unsigned char *data = urb->transfer_buffer; + int is_throttled; + unsigned long flags; + + dbg("%s - port %d", __FUNCTION__, port->number); + + if (urb->status) { + dbg("%s - nonzero read bulk status received: %d", __FUNCTION__, urb->status); + return; + } + + usb_serial_debug_data(debug, &port->dev, __FUNCTION__, urb->actual_length, data); + + /* Throttle the device if requested by tty */ + if (urb->actual_length) { + spin_lock_irqsave(&port->lock, flags); + is_throttled = port->throttled = port->throttle_req; + spin_unlock_irqrestore(&port->lock, flags); + if (is_throttled) { + /* Let the received data linger in the read URB; + * usb_serial_generic_unthrottle() will pick it + * up later. */ + dbg("%s - throttling device", __FUNCTION__); + return; + } + } + + /* Handle data and continue reading from device */ + flush_and_resubmit_read_urb(port); +} EXPORT_SYMBOL_GPL(usb_serial_generic_read_bulk_callback); void usb_serial_generic_write_bulk_callback (struct urb *urb) @@ -308,6 +342,38 @@ void usb_serial_generic_write_bulk_callback (struct urb *urb) } EXPORT_SYMBOL_GPL(usb_serial_generic_write_bulk_callback); +void usb_serial_generic_throttle (struct usb_serial_port *port) +{ + unsigned long flags; + + dbg("%s - port %d", __FUNCTION__, port->number); + + /* Set the throttle request flag. It will be picked up + * by usb_serial_generic_read_bulk_callback(). */ + spin_lock_irqsave(&port->lock, flags); + port->throttle_req = 1; + spin_unlock_irqrestore(&port->lock, flags); +} + +void usb_serial_generic_unthrottle (struct usb_serial_port *port) +{ + int was_throttled; + unsigned long flags; + + dbg("%s - port %d", __FUNCTION__, port->number); + + /* Clear the throttle flags */ + spin_lock_irqsave(&port->lock, flags); + was_throttled = port->throttled; + port->throttled = port->throttle_req = 0; + spin_unlock_irqrestore(&port->lock, flags); + + if (was_throttled) { + /* Handle pending data and resume reading from device */ + flush_and_resubmit_read_urb(port); + } +} + void usb_serial_generic_shutdown (struct usb_serial *serial) { int i; diff --git a/drivers/usb/serial/option.c b/drivers/usb/serial/option.c index ced9f32b29d9..9963a8b75840 100644 --- a/drivers/usb/serial/option.c +++ b/drivers/usb/serial/option.c @@ -69,7 +69,6 @@ static int option_send_setup(struct usb_serial_port *port); /* Vendor and product IDs */ #define OPTION_VENDOR_ID 0x0AF0 #define HUAWEI_VENDOR_ID 0x12D1 -#define AUDIOVOX_VENDOR_ID 0x0F3D #define NOVATELWIRELESS_VENDOR_ID 0x1410 #define ANYDATA_VENDOR_ID 0x16d5 @@ -81,7 +80,6 @@ static int option_send_setup(struct usb_serial_port *port); #define OPTION_PRODUCT_GTMAX36 0x6701 #define HUAWEI_PRODUCT_E600 0x1001 #define HUAWEI_PRODUCT_E220 0x1003 -#define AUDIOVOX_PRODUCT_AIRCARD 0x0112 #define NOVATELWIRELESS_PRODUCT_U740 0x1400 #define ANYDATA_PRODUCT_ID 0x6501 @@ -94,7 +92,6 @@ static struct usb_device_id option_ids[] = { { USB_DEVICE(OPTION_VENDOR_ID, OPTION_PRODUCT_GTMAX36) }, { USB_DEVICE(HUAWEI_VENDOR_ID, HUAWEI_PRODUCT_E600) }, { USB_DEVICE(HUAWEI_VENDOR_ID, HUAWEI_PRODUCT_E220) }, - { USB_DEVICE(AUDIOVOX_VENDOR_ID, AUDIOVOX_PRODUCT_AIRCARD) }, { USB_DEVICE(NOVATELWIRELESS_VENDOR_ID,NOVATELWIRELESS_PRODUCT_U740) }, { USB_DEVICE(ANYDATA_VENDOR_ID, ANYDATA_PRODUCT_ID) }, { } /* Terminating entry */ @@ -109,7 +106,6 @@ static struct usb_device_id option_ids1[] = { { USB_DEVICE(OPTION_VENDOR_ID, OPTION_PRODUCT_GTMAX36) }, { USB_DEVICE(HUAWEI_VENDOR_ID, HUAWEI_PRODUCT_E600) }, { USB_DEVICE(HUAWEI_VENDOR_ID, HUAWEI_PRODUCT_E220) }, - { USB_DEVICE(AUDIOVOX_VENDOR_ID, AUDIOVOX_PRODUCT_AIRCARD) }, { USB_DEVICE(NOVATELWIRELESS_VENDOR_ID,NOVATELWIRELESS_PRODUCT_U740) }, { USB_DEVICE(ANYDATA_VENDOR_ID, ANYDATA_PRODUCT_ID) }, { } /* Terminating entry */ diff --git a/drivers/usb/serial/pl2303.c b/drivers/usb/serial/pl2303.c index 6c083d4e2c9b..83dfae93a45d 100644 --- a/drivers/usb/serial/pl2303.c +++ b/drivers/usb/serial/pl2303.c @@ -83,6 +83,7 @@ static struct usb_device_id id_table [] = { { USB_DEVICE(BELKIN_VENDOR_ID, BELKIN_PRODUCT_ID) }, { USB_DEVICE(ALCOR_VENDOR_ID, ALCOR_PRODUCT_ID) }, { USB_DEVICE(HUAWEI_VENDOR_ID, HUAWEI_PRODUCT_ID) }, + { USB_DEVICE(WS002IN_VENDOR_ID, WS002IN_PRODUCT_ID) }, { } /* Terminating entry */ }; diff --git a/drivers/usb/serial/pl2303.h b/drivers/usb/serial/pl2303.h index 65a5039665e7..f9a71d0c102e 100644 --- a/drivers/usb/serial/pl2303.h +++ b/drivers/usb/serial/pl2303.h @@ -97,3 +97,8 @@ /* Huawei E620 UMTS/HSDPA card (ID: 12d1:1001) */ #define HUAWEI_VENDOR_ID 0x12d1 #define HUAWEI_PRODUCT_ID 0x1001 + +/* Willcom WS002IN Data Driver (by NetIndex Inc.) */ +#define WS002IN_VENDOR_ID 0x11f6 +#define WS002IN_PRODUCT_ID 0x2001 + diff --git a/drivers/usb/storage/scsiglue.c b/drivers/usb/storage/scsiglue.c index 70234f5dbeeb..e227f64d5641 100644 --- a/drivers/usb/storage/scsiglue.c +++ b/drivers/usb/storage/scsiglue.c @@ -153,6 +153,12 @@ static int slave_configure(struct scsi_device *sdev) if (us->flags & US_FL_FIX_CAPACITY) sdev->fix_capacity = 1; + /* A few disks have two indistinguishable version, one of + * which reports the correct capacity and the other does not. + * The sd driver has to guess which is the case. */ + if (us->flags & US_FL_CAPACITY_HEURISTICS) + sdev->guess_capacity = 1; + /* Some devices report a SCSI revision level above 2 but are * unable to handle the REPORT LUNS command (for which * support is mandatory at level 3). Since we already have diff --git a/drivers/usb/storage/unusual_devs.h b/drivers/usb/storage/unusual_devs.h index f49a62fc32d2..9644a8ea4aa7 100644 --- a/drivers/usb/storage/unusual_devs.h +++ b/drivers/usb/storage/unusual_devs.h @@ -1101,6 +1101,15 @@ UNUSUAL_DEV( 0x08bd, 0x1100, 0x0000, 0x0000, US_SC_DEVICE, US_PR_DEVICE, NULL, US_FL_SINGLE_LUN), +/* Submitted by Dylan Taft <d13f00l@gmail.com> + * US_FL_IGNORE_RESIDUE Needed + */ +UNUSUAL_DEV( 0x08ca, 0x3103, 0x0100, 0x0100, + "AIPTEK", + "Aiptek USB Keychain MP3 Player", + US_SC_DEVICE, US_PR_DEVICE, NULL, + US_FL_IGNORE_RESIDUE), + /* Entry needed for flags. Moreover, all devices with this ID use * bulk-only transport, but _some_ falsely report Control/Bulk instead. * One example is "Trumpion Digital Research MYMP3". @@ -1311,12 +1320,13 @@ UNUSUAL_DEV( 0x0fce, 0xd008, 0x0000, 0x0000, US_SC_DEVICE, US_PR_DEVICE, NULL, US_FL_NO_WP_DETECT ), -/* Reported by Jan Mate <mate@fiit.stuba.sk> */ +/* Reported by Jan Mate <mate@fiit.stuba.sk> + * and by Soeren Sonnenburg <kernel@nn7.de> */ UNUSUAL_DEV( 0x0fce, 0xe030, 0x0000, 0x0000, "Sony Ericsson", "P990i", US_SC_DEVICE, US_PR_DEVICE, NULL, - US_FL_FIX_CAPACITY ), + US_FL_FIX_CAPACITY | US_FL_IGNORE_RESIDUE ), /* Reported by Emmanuel Vasilakis <evas@forthnet.gr> */ UNUSUAL_DEV( 0x0fce, 0xe031, 0x0000, 0x0000, @@ -1385,6 +1395,16 @@ UNUSUAL_DEV( 0x1652, 0x6600, 0x0201, 0x0201, US_SC_DEVICE, US_PR_DEVICE, NULL, US_FL_IGNORE_RESIDUE ), +/* Reported by Thomas Baechler <thomas@archlinux.org> + * Fixes I/O errors with Teac HD-35PU devices + */ + +UNUSUAL_DEV( 0x1652, 0x6600, 0x0201, 0x0201, + "Super Top", + "USB 2.0 IDE DEVICE", + US_SC_DEVICE, US_PR_DEVICE, NULL, + US_FL_IGNORE_RESIDUE), + /* patch submitted by Davide Perini <perini.davide@dpsoftware.org> * and Renato Perini <rperini@email.it> */ @@ -1423,7 +1443,7 @@ UNUSUAL_DEV( 0xed06, 0x4500, 0x0001, 0x0001, "DataStor", "USB4500 FW1.04", US_SC_DEVICE, US_PR_DEVICE, NULL, - US_FL_FIX_CAPACITY), + US_FL_CAPACITY_HEURISTICS), /* Control/Bulk transport for all SubClass values */ USUAL_DEV(US_SC_RBC, US_PR_CB, USB_US_TYPE_STOR), diff --git a/drivers/usb/usb-skeleton.c b/drivers/usb/usb-skeleton.c index 296b091cf168..46929a1b6f24 100644 --- a/drivers/usb/usb-skeleton.c +++ b/drivers/usb/usb-skeleton.c @@ -90,13 +90,15 @@ static int skel_open(struct inode *inode, struct file *file) goto exit; } + /* increment our usage count for the device */ + kref_get(&dev->kref); + /* prevent the device from being autosuspended */ retval = usb_autopm_get_interface(interface); - if (retval) + if (retval) { + kref_put(&dev->kref, skel_delete); goto exit; - - /* increment our usage count for the device */ - kref_get(&dev->kref); + } /* save our object in the file's private structure */ file->private_data = dev; |