diff options
Diffstat (limited to 'drivers/net/e1000e/ich8lan.c')
| -rw-r--r-- | drivers/net/e1000e/ich8lan.c | 2225 |
1 files changed, 2225 insertions, 0 deletions
diff --git a/drivers/net/e1000e/ich8lan.c b/drivers/net/e1000e/ich8lan.c new file mode 100644 index 000000000000..8f8139de1f48 --- /dev/null +++ b/drivers/net/e1000e/ich8lan.c @@ -0,0 +1,2225 @@ +/******************************************************************************* + + Intel PRO/1000 Linux driver + Copyright(c) 1999 - 2007 Intel Corporation. + + This program is free software; you can redistribute it and/or modify it + under the terms and conditions of the GNU General Public License, + version 2, as published by the Free Software Foundation. + + This program is distributed in the hope it will be useful, but WITHOUT + ANY WARRANTY; without even the implied warranty of MERCHANTABILITY or + FITNESS FOR A PARTICULAR PURPOSE. See the GNU General Public License for + more details. + + You should have received a copy of the GNU General Public License along with + this program; if not, write to the Free Software Foundation, Inc., + 51 Franklin St - Fifth Floor, Boston, MA 02110-1301 USA. + + The full GNU General Public License is included in this distribution in + the file called "COPYING". + + Contact Information: + Linux NICS <linux.nics@intel.com> + e1000-devel Mailing List <e1000-devel@lists.sourceforge.net> + Intel Corporation, 5200 N.E. Elam Young Parkway, Hillsboro, OR 97124-6497 + +*******************************************************************************/ + +/* + * 82562G-2 10/100 Network Connection + * 82562GT 10/100 Network Connection + * 82562GT-2 10/100 Network Connection + * 82562V 10/100 Network Connection + * 82562V-2 10/100 Network Connection + * 82566DC-2 Gigabit Network Connection + * 82566DC Gigabit Network Connection + * 82566DM-2 Gigabit Network Connection + * 82566DM Gigabit Network Connection + * 82566MC Gigabit Network Connection + * 82566MM Gigabit Network Connection + */ + +#include <linux/netdevice.h> +#include <linux/ethtool.h> +#include <linux/delay.h> +#include <linux/pci.h> + +#include "e1000.h" + +#define ICH_FLASH_GFPREG 0x0000 +#define ICH_FLASH_HSFSTS 0x0004 +#define ICH_FLASH_HSFCTL 0x0006 +#define ICH_FLASH_FADDR 0x0008 +#define ICH_FLASH_FDATA0 0x0010 + +#define ICH_FLASH_READ_COMMAND_TIMEOUT 500 +#define ICH_FLASH_WRITE_COMMAND_TIMEOUT 500 +#define ICH_FLASH_ERASE_COMMAND_TIMEOUT 3000000 +#define ICH_FLASH_LINEAR_ADDR_MASK 0x00FFFFFF +#define ICH_FLASH_CYCLE_REPEAT_COUNT 10 + +#define ICH_CYCLE_READ 0 +#define ICH_CYCLE_WRITE 2 +#define ICH_CYCLE_ERASE 3 + +#define FLASH_GFPREG_BASE_MASK 0x1FFF +#define FLASH_SECTOR_ADDR_SHIFT 12 + +#define ICH_FLASH_SEG_SIZE_256 256 +#define ICH_FLASH_SEG_SIZE_4K 4096 +#define ICH_FLASH_SEG_SIZE_8K 8192 +#define ICH_FLASH_SEG_SIZE_64K 65536 + + +#define E1000_ICH_FWSM_RSPCIPHY 0x00000040 /* Reset PHY on PCI Reset */ + +#define E1000_ICH_MNG_IAMT_MODE 0x2 + +#define ID_LED_DEFAULT_ICH8LAN ((ID_LED_DEF1_DEF2 << 12) | \ + (ID_LED_DEF1_OFF2 << 8) | \ + (ID_LED_DEF1_ON2 << 4) | \ + (ID_LED_DEF1_DEF2)) + +#define E1000_ICH_NVM_SIG_WORD 0x13 +#define E1000_ICH_NVM_SIG_MASK 0xC000 + +#define E1000_ICH8_LAN_INIT_TIMEOUT 1500 + +#define E1000_FEXTNVM_SW_CONFIG 1 +#define E1000_FEXTNVM_SW_CONFIG_ICH8M (1 << 27) /* Bit redefined for ICH8M :/ */ + +#define PCIE_ICH8_SNOOP_ALL PCIE_NO_SNOOP_ALL + +#define E1000_ICH_RAR_ENTRIES 7 + +#define PHY_PAGE_SHIFT 5 +#define PHY_REG(page, reg) (((page) << PHY_PAGE_SHIFT) | \ + ((reg) & MAX_PHY_REG_ADDRESS)) +#define IGP3_KMRN_DIAG PHY_REG(770, 19) /* KMRN Diagnostic */ +#define IGP3_VR_CTRL PHY_REG(776, 18) /* Voltage Regulator Control */ + +#define IGP3_KMRN_DIAG_PCS_LOCK_LOSS 0x0002 +#define IGP3_VR_CTRL_DEV_POWERDOWN_MODE_MASK 0x0300 +#define IGP3_VR_CTRL_MODE_SHUTDOWN 0x0200 + +/* ICH GbE Flash Hardware Sequencing Flash Status Register bit breakdown */ +/* Offset 04h HSFSTS */ +union ich8_hws_flash_status { + struct ich8_hsfsts { + u16 flcdone :1; /* bit 0 Flash Cycle Done */ + u16 flcerr :1; /* bit 1 Flash Cycle Error */ + u16 dael :1; /* bit 2 Direct Access error Log */ + u16 berasesz :2; /* bit 4:3 Sector Erase Size */ + u16 flcinprog :1; /* bit 5 flash cycle in Progress */ + u16 reserved1 :2; /* bit 13:6 Reserved */ + u16 reserved2 :6; /* bit 13:6 Reserved */ + u16 fldesvalid :1; /* bit 14 Flash Descriptor Valid */ + u16 flockdn :1; /* bit 15 Flash Config Lock-Down */ + } hsf_status; + u16 regval; +}; + +/* ICH GbE Flash Hardware Sequencing Flash control Register bit breakdown */ +/* Offset 06h FLCTL */ +union ich8_hws_flash_ctrl { + struct ich8_hsflctl { + u16 flcgo :1; /* 0 Flash Cycle Go */ + u16 flcycle :2; /* 2:1 Flash Cycle */ + u16 reserved :5; /* 7:3 Reserved */ + u16 fldbcount :2; /* 9:8 Flash Data Byte Count */ + u16 flockdn :6; /* 15:10 Reserved */ + } hsf_ctrl; + u16 regval; +}; + +/* ICH Flash Region Access Permissions */ +union ich8_hws_flash_regacc { + struct ich8_flracc { + u32 grra :8; /* 0:7 GbE region Read Access */ + u32 grwa :8; /* 8:15 GbE region Write Access */ + u32 gmrag :8; /* 23:16 GbE Master Read Access Grant */ + u32 gmwag :8; /* 31:24 GbE Master Write Access Grant */ + } hsf_flregacc; + u16 regval; +}; + +static s32 e1000_setup_link_ich8lan(struct e1000_hw *hw); +static void e1000_clear_hw_cntrs_ich8lan(struct e1000_hw *hw); +static void e1000_initialize_hw_bits_ich8lan(struct e1000_hw *hw); +static s32 e1000_check_polarity_ife_ich8lan(struct e1000_hw *hw); +static s32 e1000_erase_flash_bank_ich8lan(struct e1000_hw *hw, u32 bank); +static s32 e1000_retry_write_flash_byte_ich8lan(struct e1000_hw *hw, + u32 offset, u8 byte); +static s32 e1000_read_flash_word_ich8lan(struct e1000_hw *hw, u32 offset, + u16 *data); +static s32 e1000_read_flash_data_ich8lan(struct e1000_hw *hw, u32 offset, + u8 size, u16 *data); +static s32 e1000_setup_copper_link_ich8lan(struct e1000_hw *hw); +static s32 e1000_kmrn_lock_loss_workaround_ich8lan(struct e1000_hw *hw); + +static inline u16 __er16flash(struct e1000_hw *hw, unsigned long reg) +{ + return readw(hw->flash_address + reg); +} + +static inline u32 __er32flash(struct e1000_hw *hw, unsigned long reg) +{ + return readl(hw->flash_address + reg); +} + +static inline void __ew16flash(struct e1000_hw *hw, unsigned long reg, u16 val) +{ + writew(val, hw->flash_address + reg); +} + +static inline void __ew32flash(struct e1000_hw *hw, unsigned long reg, u32 val) +{ + writel(val, hw->flash_address + reg); +} + +#define er16flash(reg) __er16flash(hw, (reg)) +#define er32flash(reg) __er32flash(hw, (reg)) +#define ew16flash(reg,val) __ew16flash(hw, (reg), (val)) +#define ew32flash(reg,val) __ew32flash(hw, (reg), (val)) + +/** + * e1000_init_phy_params_ich8lan - Initialize PHY function pointers + * @hw: pointer to the HW structure + * + * Initialize family-specific PHY parameters and function pointers. + **/ +static s32 e1000_init_phy_params_ich8lan(struct e1000_hw *hw) +{ + struct e1000_phy_info *phy = &hw->phy; + s32 ret_val; + u16 i = 0; + + phy->addr = 1; + phy->reset_delay_us = 100; + + phy->id = 0; + while ((e1000_phy_unknown == e1000e_get_phy_type_from_id(phy->id)) && + (i++ < 100)) { + msleep(1); + ret_val = e1000e_get_phy_id(hw); + if (ret_val) + return ret_val; + } + + /* Verify phy id */ + switch (phy->id) { + case IGP03E1000_E_PHY_ID: + phy->type = e1000_phy_igp_3; + phy->autoneg_mask = AUTONEG_ADVERTISE_SPEED_DEFAULT; + break; + case IFE_E_PHY_ID: + case IFE_PLUS_E_PHY_ID: + case IFE_C_E_PHY_ID: + phy->type = e1000_phy_ife; + phy->autoneg_mask = E1000_ALL_NOT_GIG; + break; + default: + return -E1000_ERR_PHY; + break; + } + + return 0; +} + +/** + * e1000_init_nvm_params_ich8lan - Initialize NVM function pointers + * @hw: pointer to the HW structure + * + * Initialize family-specific NVM parameters and function + * pointers. + **/ +static s32 e1000_init_nvm_params_ich8lan(struct e1000_hw *hw) +{ + struct e1000_nvm_info *nvm = &hw->nvm; + struct e1000_dev_spec_ich8lan *dev_spec = &hw->dev_spec.ich8lan; + u32 gfpreg; + u32 sector_base_addr; + u32 sector_end_addr; + u16 i; + + /* Can't read flash registers if the register set isn't mapped. + */ + if (!hw->flash_address) { + hw_dbg(hw, "ERROR: Flash registers not mapped\n"); + return -E1000_ERR_CONFIG; + } + + nvm->type = e1000_nvm_flash_sw; + + gfpreg = er32flash(ICH_FLASH_GFPREG); + + /* sector_X_addr is a "sector"-aligned address (4096 bytes) + * Add 1 to sector_end_addr since this sector is included in + * the overall size. */ + sector_base_addr = gfpreg & FLASH_GFPREG_BASE_MASK; + sector_end_addr = ((gfpreg >> 16) & FLASH_GFPREG_BASE_MASK) + 1; + + /* flash_base_addr is byte-aligned */ + nvm->flash_base_addr = sector_base_addr << FLASH_SECTOR_ADDR_SHIFT; + + /* find total size of the NVM, then cut in half since the total + * size represents two separate NVM banks. */ + nvm->flash_bank_size = (sector_end_addr - sector_base_addr) + << FLASH_SECTOR_ADDR_SHIFT; + nvm->flash_bank_size /= 2; + /* Adjust to word count */ + nvm->flash_bank_size /= sizeof(u16); + + nvm->word_size = E1000_ICH8_SHADOW_RAM_WORDS; + + /* Clear shadow ram */ + for (i = 0; i < nvm->word_size; i++) { + dev_spec->shadow_ram[i].modified = 0; + dev_spec->shadow_ram[i].value = 0xFFFF; + } + + return 0; +} + +/** + * e1000_init_mac_params_ich8lan - Initialize MAC function pointers + * @hw: pointer to the HW structure + * + * Initialize family-specific MAC parameters and function + * pointers. + **/ +static s32 e1000_init_mac_params_ich8lan(struct e1000_adapter *adapter) +{ + struct e1000_hw *hw = &adapter->hw; + struct e1000_mac_info *mac = &hw->mac; + + /* Set media type function pointer */ + hw->media_type = e1000_media_type_copper; + + /* Set mta register count */ + mac->mta_reg_count = 32; + /* Set rar entry count */ + mac->rar_entry_count = E1000_ICH_RAR_ENTRIES; + if (mac->type == e1000_ich8lan) + mac->rar_entry_count--; + /* Set if manageability features are enabled. */ + mac->arc_subsystem_valid = 1; + + /* Enable PCS Lock-loss workaround for ICH8 */ + if (mac->type == e1000_ich8lan) + e1000e_set_kmrn_lock_loss_workaround_ich8lan(hw, 1); + + return 0; +} + +static s32 e1000_get_invariants_ich8lan(struct e1000_adapter *adapter) +{ + struct e1000_hw *hw = &adapter->hw; + s32 rc; + + rc = e1000_init_mac_params_ich8lan(adapter); + if (rc) + return rc; + + rc = e1000_init_nvm_params_ich8lan(hw); + if (rc) + return rc; + + rc = e1000_init_phy_params_ich8lan(hw); + if (rc) + return rc; + + if ((adapter->hw.mac.type == e1000_ich8lan) && + (adapter->hw.phy.type == e1000_phy_igp_3)) + adapter->flags |= FLAG_LSC_GIG_SPEED_DROP; + + return 0; +} + +/** + * e1000_acquire_swflag_ich8lan - Acquire software control flag + * @hw: pointer to the HW structure + * + * Acquires the software control flag for performing NVM and PHY + * operations. This is a function pointer entry point only called by + * read/write routines for the PHY and NVM parts. + **/ +static s32 e1000_acquire_swflag_ich8lan(struct e1000_hw *hw) +{ + u32 extcnf_ctrl; + u32 timeout = PHY_CFG_TIMEOUT; + + while (timeout) { + extcnf_ctrl = er32(EXTCNF_CTRL); + extcnf_ctrl |= E1000_EXTCNF_CTRL_SWFLAG; + ew32(EXTCNF_CTRL, extcnf_ctrl); + + extcnf_ctrl = er32(EXTCNF_CTRL); + if (extcnf_ctrl & E1000_EXTCNF_CTRL_SWFLAG) + break; + mdelay(1); + timeout--; + } + + if (!timeout) { + hw_dbg(hw, "FW or HW has locked the resource for too long.\n"); + return -E1000_ERR_CONFIG; + } + + return 0; +} + +/** + * e1000_release_swflag_ich8lan - Release software control flag + * @hw: pointer to the HW structure + * + * Releases the software control flag for performing NVM and PHY operations. + * This is a function pointer entry point only called by read/write + * routines for the PHY and NVM parts. + **/ +static void e1000_release_swflag_ich8lan(struct e1000_hw *hw) +{ + u32 extcnf_ctrl; + + extcnf_ctrl = er32(EXTCNF_CTRL); + extcnf_ctrl &= ~E1000_EXTCNF_CTRL_SWFLAG; + ew32(EXTCNF_CTRL, extcnf_ctrl); +} + +/** + * e1000_check_reset_block_ich8lan - Check if PHY reset is blocked + * @hw: pointer to the HW structure + * + * Checks if firmware is blocking the reset of the PHY. + * This is a function pointer entry point only called by + * reset routines. + **/ +static s32 e1000_check_reset_block_ich8lan(struct e1000_hw *hw) +{ + u32 fwsm; + + fwsm = er32(FWSM); + + return (fwsm & E1000_ICH_FWSM_RSPCIPHY) ? 0 : E1000_BLK_PHY_RESET; +} + +/** + * e1000_phy_force_speed_duplex_ich8lan - Force PHY speed & duplex + * @hw: pointer to the HW structure + * + * Forces the speed and duplex settings of the PHY. + * This is a function pointer entry point only called by + * PHY setup routines. + **/ +static s32 e1000_phy_force_speed_duplex_ich8lan(struct e1000_hw *hw) +{ + struct e1000_phy_info *phy = &hw->phy; + s32 ret_val; + u16 data; + bool link; + + if (phy->type != e1000_phy_ife) { + ret_val = e1000e_phy_force_speed_duplex_igp(hw); + return ret_val; + } + + ret_val = e1e_rphy(hw, PHY_CONTROL, &data); + if (ret_val) + return ret_val; + + e1000e_phy_force_speed_duplex_setup(hw, &data); + + ret_val = e1e_wphy(hw, PHY_CONTROL, data); + if (ret_val) + return ret_val; + + /* Disable MDI-X support for 10/100 */ + ret_val = e1e_rphy(hw, IFE_PHY_MDIX_CONTROL, &data); + if (ret_val) + return ret_val; + + data &= ~IFE_PMC_AUTO_MDIX; + data &= ~IFE_PMC_FORCE_MDIX; + + ret_val = e1e_wphy(hw, IFE_PHY_MDIX_CONTROL, data); + if (ret_val) + return ret_val; + + hw_dbg(hw, "IFE PMC: %X\n", data); + + udelay(1); + + if (phy->wait_for_link) { + hw_dbg(hw, "Waiting for forced speed/duplex link on IFE phy.\n"); + + ret_val = e1000e_phy_has_link_generic(hw, + PHY_FORCE_LIMIT, + 100000, + &link); + if (ret_val) + return ret_val; + + if (!link) + hw_dbg(hw, "Link taking longer than expected.\n"); + + /* Try once more */ + ret_val = e1000e_phy_has_link_generic(hw, + PHY_FORCE_LIMIT, + 100000, + &link); + if (ret_val) + return ret_val; + } + + return 0; +} + +/** + * e1000_phy_hw_reset_ich8lan - Performs a PHY reset + * @hw: pointer to the HW structure + * + * Resets the PHY + * This is a function pointer entry point called by drivers + * or other shared routines. + **/ +static s32 e1000_phy_hw_reset_ich8lan(struct e1000_hw *hw) +{ + struct e1000_phy_info *phy = &hw->phy; + u32 i; + u32 data, cnf_size, cnf_base_addr, sw_cfg_mask; + s32 ret_val; + u16 loop = E1000_ICH8_LAN_INIT_TIMEOUT; + u16 word_addr, reg_data, reg_addr, phy_page = 0; + + ret_val = e1000e_phy_hw_reset_generic(hw); + if (ret_val) + return ret_val; + + /* Initialize the PHY from the NVM on ICH platforms. This + * is needed due to an issue where the NVM configuration is + * not properly autoloaded after power transitions. + * Therefore, after each PHY reset, we will load the + * configuration data out of the NVM manually. + */ + if (hw->mac.type == e1000_ich8lan && phy->type == e1000_phy_igp_3) { + struct e1000_adapter *adapter = hw->adapter; + + /* Check if SW needs configure the PHY */ + if ((adapter->pdev->device == E1000_DEV_ID_ICH8_IGP_M_AMT) || + (adapter->pdev->device == E1000_DEV_ID_ICH8_IGP_M)) + sw_cfg_mask = E1000_FEXTNVM_SW_CONFIG_ICH8M; + else + sw_cfg_mask = E1000_FEXTNVM_SW_CONFIG; + + data = er32(FEXTNVM); + if (!(data & sw_cfg_mask)) + return 0; + + /* Wait for basic configuration completes before proceeding*/ + do { + data = er32(STATUS); + data &= E1000_STATUS_LAN_INIT_DONE; + udelay(100); + } while ((!data) && --loop); + + /* If basic configuration is incomplete before the above loop + * count reaches 0, loading the configuration from NVM will + * leave the PHY in a bad state possibly resulting in no link. + */ + if (loop == 0) { + hw_dbg(hw, "LAN_INIT_DONE not set, increase timeout\n"); + } + + /* Clear the Init Done bit for the next init event */ + data = er32(STATUS); + data &= ~E1000_STATUS_LAN_INIT_DONE; + ew32(STATUS, data); + + /* Make sure HW does not configure LCD from PHY + * extended configuration before SW configuration */ + data = er32(EXTCNF_CTRL); + if (data & E1000_EXTCNF_CTRL_LCD_WRITE_ENABLE) + return 0; + + cnf_size = er32(EXTCNF_SIZE); + cnf_size &= E1000_EXTCNF_SIZE_EXT_PCIE_LENGTH_MASK; + cnf_size >>= E1000_EXTCNF_SIZE_EXT_PCIE_LENGTH_SHIFT; + if (!cnf_size) + return 0; + + cnf_base_addr = data & E1000_EXTCNF_CTRL_EXT_CNF_POINTER_MASK; + cnf_base_addr >>= E1000_EXTCNF_CTRL_EXT_CNF_POINTER_SHIFT; + + /* Configure LCD from extended configuration + * region. */ + + /* cnf_base_addr is in DWORD */ + word_addr = (u16)(cnf_base_addr << 1); + + for (i = 0; i < cnf_size; i++) { + ret_val = e1000_read_nvm(hw, + (word_addr + i * 2), + 1, + ®_data); + if (ret_val) + return ret_val; + + ret_val = e1000_read_nvm(hw, + (word_addr + i * 2 + 1), + 1, + ®_addr); + if (ret_val) + return ret_val; + + /* Save off the PHY page for future writes. */ + if (reg_addr == IGP01E1000_PHY_PAGE_SELECT) { + phy_page = reg_data; + continue; + } + + reg_addr |= phy_page; + + ret_val = e1e_wphy(hw, (u32)reg_addr, reg_data); + if (ret_val) + return ret_val; + } + } + + return 0; +} + +/** + * e1000_get_phy_info_ife_ich8lan - Retrieves various IFE PHY states + * @hw: pointer to the HW structure + * + * Populates "phy" structure with various feature states. + * This function is only called by other family-specific + * routines. + **/ +static s32 e1000_get_phy_info_ife_ich8lan(struct e1000_hw *hw) +{ + struct e1000_phy_info *phy = &hw->phy; + s32 ret_val; + u16 data; + bool link; + + ret_val = e1000e_phy_has_link_generic(hw, 1, 0, &link); + if (ret_val) + return ret_val; + + if (!link) { + hw_dbg(hw, "Phy info is only valid if link is up\n"); + return -E1000_ERR_CONFIG; + } + + ret_val = e1e_rphy(hw, IFE_PHY_SPECIAL_CONTROL, &data); + if (ret_val) + return ret_val; + phy->polarity_correction = (!(data & IFE_PSC_AUTO_POLARITY_DISABLE)); + + if (phy->polarity_correction) { + ret_val = e1000_check_polarity_ife_ich8lan(hw); + if (ret_val) + return ret_val; + } else { + /* Polarity is forced */ + phy->cable_polarity = (data & IFE_PSC_FORCE_POLARITY) + ? e1000_rev_polarity_reversed + : e1000_rev_polarity_normal; + } + + ret_val = e1e_rphy(hw, IFE_PHY_MDIX_CONTROL, &data); + if (ret_val) + return ret_val; + + phy->is_mdix = (data & IFE_PMC_MDIX_STATUS); + + /* The following parameters are undefined for 10/100 operation. */ + phy->cable_length = E1000_CABLE_LENGTH_UNDEFINED; + phy->local_rx = e1000_1000t_rx_status_undefined; + phy->remote_rx = e1000_1000t_rx_status_undefined; + + return 0; +} + +/** + * e1000_get_phy_info_ich8lan - Calls appropriate PHY type get_phy_info + * @hw: pointer to the HW structure + * + * Wrapper for calling the get_phy_info routines for the appropriate phy type. + * This is a function pointer entry point called by drivers + * or other shared routines. + **/ +static s32 e1000_get_phy_info_ich8lan(struct e1000_hw *hw) +{ + switch (hw->phy.type) { + case e1000_phy_ife: + return e1000_get_phy_info_ife_ich8lan(hw); + break; + case e1000_phy_igp_3: + return e1000e_get_phy_info_igp(hw); + break; + default: + break; + } + + return -E1000_ERR_PHY_TYPE; +} + +/** + * e1000_check_polarity_ife_ich8lan - Check cable polarity for IFE PHY + * @hw: pointer to the HW structure + * + * Polarity is determined on the polarity reveral feature being enabled. + * This function is only called by other family-specific + * routines. + **/ +static s32 e1000_check_polarity_ife_ich8lan(struct e1000_hw *hw) +{ + struct e1000_phy_info *phy = &hw->phy; + s32 ret_val; + u16 phy_data, offset, mask; + + /* Polarity is determined based on the reversal feature + * being enabled. + */ + if (phy->polarity_correction) { + offset = IFE_PHY_EXTENDED_STATUS_CONTROL; + mask = IFE_PESC_POLARITY_REVERSED; + } else { + offset = IFE_PHY_SPECIAL_CONTROL; + mask = IFE_PSC_FORCE_POLARITY; + } + + ret_val = e1e_rphy(hw, offset, &phy_data); + + if (!ret_val) + phy->cable_polarity = (phy_data & mask) + ? e1000_rev_polarity_reversed + : e1000_rev_polarity_normal; + + return ret_val; +} + +/** + * e1000_set_d0_lplu_state_ich8lan - Set Low Power Linkup D0 state + * @hw: pointer to the HW structure + * @active: TRUE to enable LPLU, FALSE to disable + * + * Sets the LPLU D0 state according to the active flag. When + * activating LPLU this function also disables smart speed + * and vice versa. LPLU will not be activated unless the + * device autonegotiation advertisement meets standards of + * either 10 or 10/100 or 10/100/1000 at all duplexes. + * This is a function pointer entry point only called by + * PHY setup routines. + **/ +static s32 e1000_set_d0_lplu_state_ich8lan(struct e1000_hw *hw, bool active) +{ + struct e1000_phy_info *phy = &hw->phy; + u32 phy_ctrl; + s32 ret_val = 0; + u16 data; + + if (phy->type != e1000_phy_igp_3) + return ret_val; + + phy_ctrl = er32(PHY_CTRL); + + if (active) { + phy_ctrl |= E1000_PHY_CTRL_D0A_LPLU; + ew32(PHY_CTRL, phy_ctrl); + + /* Call gig speed drop workaround on LPLU before accessing + * any PHY registers */ + if ((hw->mac.type == e1000_ich8lan) && + (hw->phy.type == e1000_phy_igp_3)) + e1000e_gig_downshift_workaround_ich8lan(hw); + + /* When LPLU is enabled, we should disable SmartSpeed */ + ret_val = e1e_rphy(hw, IGP01E1000_PHY_PORT_CONFIG, &data); + data &= ~IGP01E1000_PSCFR_SMART_SPEED; + ret_val = e1e_wphy(hw, IGP01E1000_PHY_PORT_CONFIG, data); + if (ret_val) + return ret_val; + } else { + phy_ctrl &= ~E1000_PHY_CTRL_D0A_LPLU; + ew32(PHY_CTRL, phy_ctrl); + + /* LPLU and SmartSpeed are mutually exclusive. LPLU is used + * during Dx states where the power conservation is most + * important. During driver activity we should enable + * SmartSpeed, so performance is maintained. */ + if (phy->smart_speed == e1000_smart_speed_on) { + ret_val = e1e_rphy(hw, IGP01E1000_PHY_PORT_CONFIG, + &data); + if (ret_val) + return ret_val; + + data |= IGP01E1000_PSCFR_SMART_SPEED; + ret_val = e1e_wphy(hw, IGP01E1000_PHY_PORT_CONFIG, + data); + if (ret_val) + return ret_val; + } else if (phy->smart_speed == e1000_smart_speed_off) { + ret_val = e1e_rphy(hw, IGP01E1000_PHY_PORT_CONFIG, + &data); + if (ret_val) + return ret_val; + + data &= ~IGP01E1000_PSCFR_SMART_SPEED; + ret_val = e1e_wphy(hw, IGP01E1000_PHY_PORT_CONFIG, + data); + if (ret_val) + return ret_val; + } + } + + return 0; +} + +/** + * e1000_set_d3_lplu_state_ich8lan - Set Low Power Linkup D3 state + * @hw: pointer to the HW structure + * @active: TRUE to enable LPLU, FALSE to disable + * + * Sets the LPLU D3 state according to the active flag. When + * activating LPLU this function also disables smart speed + * and vice versa. LPLU will not be activated unless the + * device autonegotiation advertisement meets standards of + * either 10 or 10/100 or 10/100/1000 at all duplexes. + * This is a function pointer entry point only called by + * PHY setup routines. + **/ +static s32 e1000_set_d3_lplu_state_ich8lan(struct e1000_hw *hw, bool active) +{ + struct e1000_phy_info *phy = &hw->phy; + u32 phy_ctrl; + s32 ret_val; + u16 data; + + phy_ctrl = er32(PHY_CTRL); + + if (!active) { + phy_ctrl &= ~E1000_PHY_CTRL_NOND0A_LPLU; + ew32(PHY_CTRL, phy_ctrl); + /* LPLU and SmartSpeed are mutually exclusive. LPLU is used + * during Dx states where the power conservation is most + * important. During driver activity we should enable + * SmartSpeed, so performance is maintained. */ + if (phy->smart_speed == e1000_smart_speed_on) { + ret_val = e1e_rphy(hw, + IGP01E1000_PHY_PORT_CONFIG, + &data); + if (ret_val) + return ret_val; + + data |= IGP01E1000_PSCFR_SMART_SPEED; + ret_val = e1e_wphy(hw, + IGP01E1000_PHY_PORT_CONFIG, + data); + if (ret_val) + return ret_val; + } else if (phy->smart_speed == e1000_smart_speed_off) { + ret_val = e1e_rphy(hw, + IGP01E1000_PHY_PORT_CONFIG, + &data); + if (ret_val) + return ret_val; + + data &= ~IGP01E1000_PSCFR_SMART_SPEED; + ret_val = e1e_wphy(hw, + IGP01E1000_PHY_PORT_CONFIG, + data); + if (ret_val) + return ret_val; + } + } else if ((phy->autoneg_advertised == E1000_ALL_SPEED_DUPLEX) || + (phy->autoneg_advertised == E1000_ALL_NOT_GIG) || + (phy->autoneg_advertised == E1000_ALL_10_SPEED)) { + phy_ctrl |= E1000_PHY_CTRL_NOND0A_LPLU; + ew32(PHY_CTRL, phy_ctrl); + + /* Call gig speed drop workaround on LPLU before accessing + * any PHY registers */ + if ((hw->mac.type == e1000_ich8lan) && + (hw->phy.type == e1000_phy_igp_3)) + e1000e_gig_downshift_workaround_ich8lan(hw); + + /* When LPLU is enabled, we should disable SmartSpeed */ + ret_val = e1e_rphy(hw, + IGP01E1000_PHY_PORT_CONFIG, + &data); + if (ret_val) + return ret_val; + + data &= ~IGP01E1000_PSCFR_SMART_SPEED; + ret_val = e1e_wphy(hw, + IGP01E1000_PHY_PORT_CONFIG, + data); + } + + return 0; +} + +/** + * e1000_read_nvm_ich8lan - Read word(s) from the NVM + * @hw: pointer to the HW structure + * @offset: The offset (in bytes) of the word(s) to read. + * @words: Size of data to read in words + * @data: Pointer to the word(s) to read at offset. + * + * Reads a word(s) from the NVM using the flash access registers. + **/ +static s32 e1000_read_nvm_ich8lan(struct e1000_hw *hw, u16 offset, u16 words, + u16 *data) +{ + struct e1000_nvm_info *nvm = &hw->nvm; + struct e1000_dev_spec_ich8lan *dev_spec = &hw->dev_spec.ich8lan; + u32 act_offset; + s32 ret_val; + u16 i, word; + + if ((offset >= nvm->word_size) || (words > nvm->word_size - offset) || + (words == 0)) { + hw_dbg(hw, "nvm parameter(s) out of bounds\n"); + return -E1000_ERR_NVM; + } + + ret_val = e1000_acquire_swflag_ich8lan(hw); + if (ret_val) + return ret_val; + + /* Start with the bank offset, then add the relative offset. */ + act_offset = (er32(EECD) & E1000_EECD_SEC1VAL) + ? nvm->flash_bank_size + : 0; + act_offset += offset; + + for (i = 0; i < words; i++) { + if ((dev_spec->shadow_ram) && + (dev_spec->shadow_ram[offset+i].modified)) { + data[i] = dev_spec->shadow_ram[offset+i].value; + } else { + ret_val = e1000_read_flash_word_ich8lan(hw, + act_offset + i, + &word); + if (ret_val) + break; + data[i] = word; + } + } + + e1000_release_swflag_ich8lan(hw); + + return ret_val; +} + +/** + * e1000_flash_cycle_init_ich8lan - Initialize flash + * @hw: pointer to the HW structure + * + * This function does initial flash setup so that a new read/write/erase cycle + * can be started. + **/ +static s32 e1000_flash_cycle_init_ich8lan(struct e1000_hw *hw) +{ + union ich8_hws_flash_status hsfsts; + s32 ret_val = -E1000_ERR_NVM; + s32 i = 0; + + hsfsts.regval = er16flash(ICH_FLASH_HSFSTS); + + /* Check if the flash descriptor is valid */ + if (hsfsts.hsf_status.fldesvalid == 0) { + hw_dbg(hw, "Flash descriptor invalid. " + "SW Sequencing must be used."); + return -E1000_ERR_NVM; + } + + /* Clear FCERR and DAEL in hw status by writing 1 */ + hsfsts.hsf_status.flcerr = 1; + hsfsts.hsf_status.dael = 1; + + ew16flash(ICH_FLASH_HSFSTS, hsfsts.regval); + + /* Either we should have a hardware SPI cycle in progress + * bit to check against, in order to start a new cycle or + * FDONE bit should be changed in the hardware so that it + * is 1 after harware reset, which can then be used as an + * indication whether a cycle is in progress or has been + * completed. + */ + + if (hsfsts.hsf_status.flcinprog == 0) { + /* There is no cycle running at present, + * so we can start a cycle */ + /* Begin by setting Flash Cycle Done. */ + hsfsts.hsf_status.flcdone = 1; + ew16flash(ICH_FLASH_HSFSTS, hsfsts.regval); + ret_val = 0; + } else { + /* otherwise poll for sometime so the current + * cycle has a chance to end before giving up. */ + for (i = 0; i < ICH_FLASH_READ_COMMAND_TIMEOUT; i++) { + hsfsts.regval = __er16flash(hw, ICH_FLASH_HSFSTS); + if (hsfsts.hsf_status.flcinprog == 0) { + ret_val = 0; + break; + } + udelay(1); + } + if (ret_val == 0) { + /* Successful in waiting for previous cycle to timeout, + * now set the Flash Cycle Done. */ + hsfsts.hsf_status.flcdone = 1; + ew16flash(ICH_FLASH_HSFSTS, hsfsts.regval); + } else { + hw_dbg(hw, "Flash controller busy, cannot get access"); + } + } + + return ret_val; +} + +/** + * e1000_flash_cycle_ich8lan - Starts flash cycle (read/write/erase) + * @hw: pointer to the HW structure + * @timeout: maximum time to wait for completion + * + * This function starts a flash cycle and waits for its completion. + **/ +static s32 e1000_flash_cycle_ich8lan(struct e1000_hw *hw, u32 timeout) +{ + union ich8_hws_flash_ctrl hsflctl; + union ich8_hws_flash_status hsfsts; + s32 ret_val = -E1000_ERR_NVM; + u32 i = 0; + + /* Start a cycle by writing 1 in Flash Cycle Go in Hw Flash Control */ + hsflctl.regval = er16flash(ICH_FLASH_HSFCTL); + hsflctl.hsf_ctrl.flcgo = 1; + ew16flash(ICH_FLASH_HSFCTL, hsflctl.regval); + + /* wait till FDONE bit is set to 1 */ + do { + hsfsts.regval = er16flash(ICH_FLASH_HSFSTS); + if (hsfsts.hsf_status.flcdone == 1) + break; + udelay(1); + } while (i++ < timeout); + + if (hsfsts.hsf_status.flcdone == 1 && hsfsts.hsf_status.flcerr == 0) + return 0; + + return ret_val; +} + +/** + * e1000_read_flash_word_ich8lan - Read word from flash + * @hw: pointer to the HW structure + * @offset: offset to data location + * @data: pointer to the location for storing the data + * + * Reads the flash word at offset into data. Offset is converted + * to bytes before read. + **/ +static s32 e1000_read_flash_word_ich8lan(struct e1000_hw *hw, u32 offset, + u16 *data) +{ + /* Must convert offset into bytes. */ + offset <<= 1; + + return e1000_read_flash_data_ich8lan(hw, offset, 2, data); +} + +/** + * e1000_read_flash_data_ich8lan - Read byte or word from NVM + * @hw: pointer to the HW structure + * @offset: The offset (in bytes) of the byte or word to read. + * @size: Size of data to read, 1=byte 2=word + * @data: Pointer to the word to store the value read. + * + * Reads a byte or word from the NVM using the flash access registers. + **/ +static s32 e1000_read_flash_data_ich8lan(struct e1000_hw *hw, u32 offset, + u8 size, u16 *data) +{ + union ich8_hws_flash_status hsfsts; + union ich8_hws_flash_ctrl hsflctl; + u32 flash_linear_addr; + u32 flash_data = 0; + s32 ret_val = -E1000_ERR_NVM; + u8 count = 0; + + if (size < 1 || size > 2 || offset > ICH_FLASH_LINEAR_ADDR_MASK) + return -E1000_ERR_NVM; + + flash_linear_addr = (ICH_FLASH_LINEAR_ADDR_MASK & offset) + + hw->nvm.flash_base_addr; + + do { + udelay(1); + /* Steps */ + ret_val = e1000_flash_cycle_init_ich8lan(hw); + if (ret_val != 0) + break; + + hsflctl.regval = er16flash(ICH_FLASH_HSFCTL); + /* 0b/1b corresponds to 1 or 2 byte size, respectively. */ + hsflctl.hsf_ctrl.fldbcount = size - 1; + hsflctl.hsf_ctrl.flcycle = ICH_CYCLE_READ; + ew16flash(ICH_FLASH_HSFCTL, hsflctl.regval); + + ew32flash(ICH_FLASH_FADDR, flash_linear_addr); + + ret_val = e1000_flash_cycle_ich8lan(hw, + ICH_FLASH_READ_COMMAND_TIMEOUT); + + /* Check if FCERR is set to 1, if set to 1, clear it + * and try the whole sequence a few more times, else + * read in (shift in) the Flash Data0, the order is + * least significant byte first msb to lsb */ + if (ret_val == 0) { + flash_data = er32flash(ICH_FLASH_FDATA0); + if (size == 1) { + *data = (u8)(flash_data & 0x000000FF); + } else if (size == 2) { + *data = (u16)(flash_data & 0x0000FFFF); + } + break; + } else { + /* If we've gotten here, then things are probably + * completely hosed, but if the error condition is + * detected, it won't hurt to give it another try... + * ICH_FLASH_CYCLE_REPEAT_COUNT times. + */ + hsfsts.regval = er16flash(ICH_FLASH_HSFSTS); + if (hsfsts.hsf_status.flcerr == 1) { + /* Repeat for some time before giving up. */ + continue; + } else if (hsfsts.hsf_status.flcdone == 0) { + hw_dbg(hw, "Timeout error - flash cycle " + "did not complete."); + break; + } + } + } while (count++ < ICH_FLASH_CYCLE_REPEAT_COUNT); + + return ret_val; +} + +/** + * e1000_write_nvm_ich8lan - Write word(s) to the NVM + * @hw: pointer to the HW structure + * @offset: The offset (in bytes) of the word(s) to write. + * @words: Size of data to write in words + * @data: Pointer to the word(s) to write at offset. + * + * Writes a byte or word to the NVM using the flash access registers. + **/ +static s32 e1000_write_nvm_ich8lan(struct e1000_hw *hw, u16 offset, u16 words, + u16 *data) +{ + struct e1000_nvm_info *nvm = &hw->nvm; + struct e1000_dev_spec_ich8lan *dev_spec = &hw->dev_spec.ich8lan; + s32 ret_val; + u16 i; + + if ((offset >= nvm->word_size) || (words > nvm->word_size - offset) || + (words == 0)) { + hw_dbg(hw, "nvm parameter(s) out of bounds\n"); + return -E1000_ERR_NVM; + } + + ret_val = e1000_acquire_swflag_ich8lan(hw); + if (ret_val) + return ret_val; + + for (i = 0; i < words; i++) { + dev_spec->shadow_ram[offset+i].modified = 1; + dev_spec->shadow_ram[offset+i].value = data[i]; + } + + e1000_release_swflag_ich8lan(hw); + + return 0; +} + +/** + * e1000_update_nvm_checksum_ich8lan - Update the checksum for NVM + * @hw: pointer to the HW structure + * + * The NVM checksum is updated by calling the generic update_nvm_checksum, + * which writes the checksum to the shadow ram. The changes in the shadow + * ram are then committed to the EEPROM by processing each bank at a time + * checking for the modified bit and writing only the pending changes. + * After a succesful commit, the shadow ram is cleared and is ready for + * future writes. + **/ +static s32 e1000_update_nvm_checksum_ich8lan(struct e1000_hw *hw) +{ + struct e1000_nvm_info *nvm = &hw->nvm; + struct e1000_dev_spec_ich8lan *dev_spec = &hw->dev_spec.ich8lan; + u32 i, act_offset, new_bank_offset, old_bank_offset; + s32 ret_val; + u16 data; + + ret_val = e1000e_update_nvm_checksum_generic(hw); + if (ret_val) + return ret_val;; + + if (nvm->type != e1000_nvm_flash_sw) + return ret_val;; + + ret_val = e1000_acquire_swflag_ich8lan(hw); + if (ret_val) + return ret_val;; + + /* We're writing to the opposite bank so if we're on bank 1, + * write to bank 0 etc. We also need to erase the segment that + * is going to be written */ + if (!(er32(EECD) & E1000_EECD_SEC1VAL)) { + new_bank_offset = nvm->flash_bank_size; + old_bank_offset = 0; + e1000_erase_flash_bank_ich8lan(hw, 1); + } else { + old_bank_offset = nvm->flash_bank_size; + new_bank_offset = 0; + e1000_erase_flash_bank_ich8lan(hw, 0); + } + + for (i = 0; i < E1000_ICH8_SHADOW_RAM_WORDS; i++) { + /* Determine whether to write the value stored + * in the other NVM bank or a modified value stored + * in the shadow RAM */ + if (dev_spec->shadow_ram[i].modified) { + data = dev_spec->shadow_ram[i].value; + } else { + e1000_read_flash_word_ich8lan(hw, + i + old_bank_offset, + &data); + } + + /* If the word is 0x13, then make sure the signature bits + * (15:14) are 11b until the commit has completed. + * This will allow us to write 10b which indicates the + * signature is valid. We want to do this after the write + * has completed so that we don't mark the segment valid + * while the write is still in progress */ + if (i == E1000_ICH_NVM_SIG_WORD) + data |= E1000_ICH_NVM_SIG_MASK; + + /* Convert offset to bytes. */ + act_offset = (i + new_bank_offset) << 1; + + udelay(100); + /* Write the bytes to the new bank. */ + ret_val = e1000_retry_write_flash_byte_ich8lan(hw, + act_offset, + (u8)data); + if (ret_val) + break; + + udelay(100); + ret_val = e1000_retry_write_flash_byte_ich8lan(hw, + act_offset + 1, + (u8)(data >> 8)); + if (ret_val) + break; + } + + /* Don't bother writing the segment valid bits if sector + * programming failed. */ + if (ret_val) { + hw_dbg(hw, "Flash commit failed.\n"); + e1000_release_swflag_ich8lan(hw); + return ret_val; + } + + /* Finally validate the new segment by setting bit 15:14 + * to 10b in word 0x13 , this can be done without an + * erase as well since these bits are 11 to start with + * and we need to change bit 14 to 0b */ + act_offset = new_bank_offset + E1000_ICH_NVM_SIG_WORD; + e1000_read_flash_word_ich8lan(hw, act_offset, &data); + data &= 0xBFFF; + ret_val = e1000_retry_write_flash_byte_ich8lan(hw, + act_offset * 2 + 1, + (u8)(data >> 8)); + if (ret_val) { + e1000_release_swflag_ich8lan(hw); + return ret_val; + } + + /* And invalidate the previously valid segment by setting + * its signature word (0x13) high_byte to 0b. This can be + * done without an erase because flash erase sets all bits + * to 1's. We can write 1's to 0's without an erase */ + act_offset = (old_bank_offset + E1000_ICH_NVM_SIG_WORD) * 2 + 1; + ret_val = e1000_retry_write_flash_byte_ich8lan(hw, act_offset, 0); + if (ret_val) { + e1000_release_swflag_ich8lan(hw); + return ret_val; + } + + /* Great! Everything worked, we can now clear the cached entries. */ + for (i = 0; i < E1000_ICH8_SHADOW_RAM_WORDS; i++) { + dev_spec->shadow_ram[i].modified = 0; + dev_spec->shadow_ram[i].value = 0xFFFF; + } + + e1000_release_swflag_ich8lan(hw); + + /* Reload the EEPROM, or else modifications will not appear + * until after the next adapter reset. + */ + e1000e_reload_nvm(hw); + msleep(10); + + return ret_val; +} + +/** + * e1000_validate_nvm_checksum_ich8lan - Validate EEPROM checksum + * @hw: pointer to the HW structure + * + * Check to see if checksum needs to be fixed by reading bit 6 in word 0x19. + * If the bit is 0, that the EEPROM had been modified, but the checksum was not + * calculated, in which case we need to calculate the checksum and set bit 6. + **/ +static s32 e1000_validate_nvm_checksum_ich8lan(struct e1000_hw *hw) +{ + s32 ret_val; + u16 data; + + /* Read 0x19 and check bit 6. If this bit is 0, the checksum + * needs to be fixed. This bit is an indication that the NVM + * was prepared by OEM software and did not calculate the + * checksum...a likely scenario. + */ + ret_val = e1000_read_nvm(hw, 0x19, 1, &data); + if (ret_val) + return ret_val; + + if ((data & 0x40) == 0) { + data |= 0x40; + ret_val = e1000_write_nvm(hw, 0x19, 1, &data); + if (ret_val) + return ret_val; + ret_val = e1000e_update_nvm_checksum(hw); + if (ret_val) + return ret_val; + } + + return e1000e_validate_nvm_checksum_generic(hw); +} + +/** + * e1000_write_flash_data_ich8lan - Writes bytes to the NVM + * @hw: pointer to the HW structure + * @offset: The offset (in bytes) of the byte/word to read. + * @size: Size of data to read, 1=byte 2=word + * @data: The byte(s) to write to the NVM. + * + * Writes one/two bytes to the NVM using the flash access registers. + **/ +static s32 e1000_write_flash_data_ich8lan(struct e1000_hw *hw, u32 offset, + u8 size, u16 data) +{ + union ich8_hws_flash_status hsfsts; + union ich8_hws_flash_ctrl hsflctl; + u32 flash_linear_addr; + u32 flash_data = 0; + s32 ret_val; + u8 count = 0; + + if (size < 1 || size > 2 || data > size * 0xff || + offset > ICH_FLASH_LINEAR_ADDR_MASK) + return -E1000_ERR_NVM; + + flash_linear_addr = (ICH_FLASH_LINEAR_ADDR_MASK & offset) + + hw->nvm.flash_base_addr; + + do { + udelay(1); + /* Steps */ + ret_val = e1000_flash_cycle_init_ich8lan(hw); + if (ret_val) + break; + + hsflctl.regval = er16flash(ICH_FLASH_HSFCTL); + /* 0b/1b corresponds to 1 or 2 byte size, respectively. */ + hsflctl.hsf_ctrl.fldbcount = size -1; + hsflctl.hsf_ctrl.flcycle = ICH_CYCLE_WRITE; + ew16flash(ICH_FLASH_HSFCTL, hsflctl.regval); + + ew32flash(ICH_FLASH_FADDR, flash_linear_addr); + + if (size == 1) + flash_data = (u32)data & 0x00FF; + else + flash_data = (u32)data; + + ew32flash(ICH_FLASH_FDATA0, flash_data); + + /* check if FCERR is set to 1 , if set to 1, clear it + * and try the whole sequence a few more times else done */ + ret_val = e1000_flash_cycle_ich8lan(hw, + ICH_FLASH_WRITE_COMMAND_TIMEOUT); + if (!ret_val) + break; + + /* If we're here, then things are most likely + * completely hosed, but if the error condition + * is detected, it won't hurt to give it another + * try...ICH_FLASH_CYCLE_REPEAT_COUNT times. + */ + hsfsts.regval = er16flash(ICH_FLASH_HSFSTS); + if (hsfsts.hsf_status.flcerr == 1) + /* Repeat for some time before giving up. */ + continue; + if (hsfsts.hsf_status.flcdone == 0) { + hw_dbg(hw, "Timeout error - flash cycle " + "did not complete."); + break; + } + } while (count++ < ICH_FLASH_CYCLE_REPEAT_COUNT); + + return ret_val; +} + +/** + * e1000_write_flash_byte_ich8lan - Write a single byte to NVM + * @hw: pointer to the HW structure + * @offset: The index of the byte to read. + * @data: The byte to write to the NVM. + * + * Writes a single byte to the NVM using the flash access registers. + **/ +static s32 e1000_write_flash_byte_ich8lan(struct e1000_hw *hw, u32 offset, + u8 data) +{ + u16 word = (u16)data; + + return e1000_write_flash_data_ich8lan(hw, offset, 1, word); +} + +/** + * e1000_retry_write_flash_byte_ich8lan - Writes a single byte to NVM + * @hw: pointer to the HW structure + * @offset: The offset of the byte to write. + * @byte: The byte to write to the NVM. + * + * Writes a single byte to the NVM using the flash access registers. + * Goes through a retry algorithm before giving up. + **/ +static s32 e1000_retry_write_flash_byte_ich8lan(struct e1000_hw *hw, + u32 offset, u8 byte) +{ + s32 ret_val; + u16 program_retries; + + ret_val = e1000_write_flash_byte_ich8lan(hw, offset, byte); + if (!ret_val) + return ret_val; + + for (program_retries = 0; program_retries < 100; program_retries++) { + hw_dbg(hw, "Retrying Byte %2.2X at offset %u\n", byte, offset); + udelay(100); + ret_val = e1000_write_flash_byte_ich8lan(hw, offset, byte); + if (!ret_val) + break; + } + if (program_retries == 100) + return -E1000_ERR_NVM; + + return 0; +} + +/** + * e1000_erase_flash_bank_ich8lan - Erase a bank (4k) from NVM + * @hw: pointer to the HW structure + * @bank: 0 for first bank, 1 for second bank, etc. + * + * Erases the bank specified. Each bank is a 4k block. Banks are 0 based. + * bank N is 4096 * N + flash_reg_addr. + **/ +static s32 e1000_erase_flash_bank_ich8lan(struct e1000_hw *hw, u32 bank) +{ + struct e1000_nvm_info *nvm = &hw->nvm; + union ich8_hws_flash_status hsfsts; + union ich8_hws_flash_ctrl hsflctl; + u32 flash_linear_addr; + /* bank size is in 16bit words - adjust to bytes */ + u32 flash_bank_size = nvm->flash_bank_size * 2; + s32 ret_val; + s32 count = 0; + s32 iteration; + s32 sector_size; + s32 j; + + hsfsts.regval = er16flash(ICH_FLASH_HSFSTS); + + /* Determine HW Sector size: Read BERASE bits of hw flash status + * register */ + /* 00: The Hw sector is 256 bytes, hence we need to erase 16 + * consecutive sectors. The start index for the nth Hw sector + * can be calculated as = bank * 4096 + n * 256 + * 01: The Hw sector is 4K bytes, hence we need to erase 1 sector. + * The start index for the nth Hw sector can be calculated + * as = bank * 4096 + * 10: The Hw sector is 8K bytes, nth sector = bank * 8192 + * (ich9 only, otherwise error condition) + * 11: The Hw sector is 64K bytes, nth sector = bank * 65536 + */ + switch (hsfsts.hsf_status.berasesz) { + case 0: + /* Hw sector size 256 */ + sector_size = ICH_FLASH_SEG_SIZE_256; + iteration = flash_bank_size / ICH_FLASH_SEG_SIZE_256; + break; + case 1: + sector_size = ICH_FLASH_SEG_SIZE_4K; + iteration = flash_bank_size / ICH_FLASH_SEG_SIZE_4K; + break; + case 2: + if (hw->mac.type == e1000_ich9lan) { + sector_size = ICH_FLASH_SEG_SIZE_8K; + iteration = flash_bank_size / ICH_FLASH_SEG_SIZE_8K; + } else { + return -E1000_ERR_NVM; + } + break; + case 3: + sector_size = ICH_FLASH_SEG_SIZE_64K; + iteration = flash_bank_size / ICH_FLASH_SEG_SIZE_64K; + break; + default: + return -E1000_ERR_NVM; + } + + /* Start with the base address, then add the sector offset. */ + flash_linear_addr = hw->nvm.flash_base_addr; + flash_linear_addr += (bank) ? (sector_size * iteration) : 0; + + for (j = 0; j < iteration ; j++) { + do { + /* Steps */ + ret_val = e1000_flash_cycle_init_ich8lan(hw); + if (ret_val) + return ret_val; + + /* Write a value 11 (block Erase) in Flash + * Cycle field in hw flash control */ + hsflctl.regval = er16flash(ICH_FLASH_HSFCTL); + hsflctl.hsf_ctrl.flcycle = ICH_CYCLE_ERASE; + ew16flash(ICH_FLASH_HSFCTL, hsflctl.regval); + + /* Write the last 24 bits of an index within the + * block into Flash Linear address field in Flash + * Address. + */ + flash_linear_addr += (j * sector_size); + ew32flash(ICH_FLASH_FADDR, flash_linear_addr); + + ret_val = e1000_flash_cycle_ich8lan(hw, + ICH_FLASH_ERASE_COMMAND_TIMEOUT); + if (ret_val == 0) + break; + + /* Check if FCERR is set to 1. If 1, + * clear it and try the whole sequence + * a few more times else Done */ + hsfsts.regval = er16flash(ICH_FLASH_HSFSTS); + if (hsfsts.hsf_status.flcerr == 1) + /* repeat for some time before + * giving up */ + continue; + else if (hsfsts.hsf_status.flcdone == 0) + return ret_val; + } while (++count < ICH_FLASH_CYCLE_REPEAT_COUNT); + } + + return 0; +} + +/** + * e1000_valid_led_default_ich8lan - Set the default LED settings + * @hw: pointer to the HW structure + * @data: Pointer to the LED settings + * + * Reads the LED default settings from the NVM to data. If the NVM LED + * settings is all 0's or F's, set the LED default to a valid LED default + * setting. + **/ +static s32 e1000_valid_led_default_ich8lan(struct e1000_hw *hw, u16 *data) +{ + s32 ret_val; + + ret_val = e1000_read_nvm(hw, NVM_ID_LED_SETTINGS, 1, data); + if (ret_val) { + hw_dbg(hw, "NVM Read Error\n"); + return ret_val; + } + + if (*data == ID_LED_RESERVED_0000 || + *data == ID_LED_RESERVED_FFFF) + *data = ID_LED_DEFAULT_ICH8LAN; + + return 0; +} + +/** + * e1000_get_bus_info_ich8lan - Get/Set the bus type and width + * @hw: pointer to the HW structure + * + * ICH8 use the PCI Express bus, but does not contain a PCI Express Capability + * register, so the the bus width is hard coded. + **/ +static s32 e1000_get_bus_info_ich8lan(struct e1000_hw *hw) +{ + struct e1000_bus_info *bus = &hw->bus; + s32 ret_val; + + ret_val = e1000e_get_bus_info_pcie(hw); + + /* ICH devices are "PCI Express"-ish. They have + * a configuration space, but do not contain + * PCI Express Capability registers, so bus width + * must be hardcoded. + */ + if (bus->width == e1000_bus_width_unknown) + bus->width = e1000_bus_width_pcie_x1; + + return ret_val; +} + +/** + * e1000_reset_hw_ich8lan - Reset the hardware + * @hw: pointer to the HW structure + * + * Does a full reset of the hardware which includes a reset of the PHY and + * MAC. + **/ +static s32 e1000_reset_hw_ich8lan(struct e1000_hw *hw) +{ + u32 ctrl, icr, kab; + s32 ret_val; + + /* Prevent the PCI-E bus from sticking if there is no TLP connection + * on the last TLP read/write transaction when MAC is reset. + */ + ret_val = e1000e_disable_pcie_master(hw); + if (ret_val) { + hw_dbg(hw, "PCI-E Master disable polling has failed.\n"); + } + + hw_dbg(hw, "Masking off all interrupts\n"); + ew32(IMC, 0xffffffff); + + /* Disable the Transmit and Receive units. Then delay to allow + * any pending transactions to complete before we hit the MAC + * with the global reset. + */ + ew32(RCTL, 0); + ew32(TCTL, E1000_TCTL_PSP); + e1e_flush(); + + msleep(10); + + /* Workaround for ICH8 bit corruption issue in FIFO memory */ + if (hw->mac.type == e1000_ich8lan) { + /* Set Tx and Rx buffer allocation to 8k apiece. */ + ew32(PBA, E1000_PBA_8K); + /* Set Packet Buffer Size to 16k. */ + ew32(PBS, E1000_PBS_16K); + } + + ctrl = er32(CTRL); + + if (!e1000_check_reset_block(hw)) { + /* PHY HW reset requires MAC CORE reset at the same + * time to make sure the interface between MAC and the + * external PHY is reset. + */ + ctrl |= E1000_CTRL_PHY_RST; + } + ret_val = e1000_acquire_swflag_ich8lan(hw); + hw_dbg(hw, "Issuing a global reset to ich8lan"); + ew32(CTRL, (ctrl | E1000_CTRL_RST)); + msleep(20); + + ret_val = e1000e_get_auto_rd_done(hw); + if (ret_val) { + /* + * When auto config read does not complete, do not + * return with an error. This can happen in situations + * where there is no eeprom and prevents getting link. + */ + hw_dbg(hw, "Auto Read Done did not complete\n"); + } + + ew32(IMC, 0xffffffff); + icr = er32(ICR); + + kab = er32(KABGTXD); + kab |= E1000_KABGTXD_BGSQLBIAS; + ew32(KABGTXD, kab); + + return ret_val; +} + +/** + * e1000_init_hw_ich8lan - Initialize the hardware + * @hw: pointer to the HW structure + * + * Prepares the hardware for transmit and receive by doing the following: + * - initialize hardware bits + * - initialize LED identification + * - setup receive address registers + * - setup flow control + * - setup transmit discriptors + * - clear statistics + **/ +static s32 e1000_init_hw_ich8lan(struct e1000_hw *hw) +{ + struct e1000_mac_info *mac = &hw->mac; + u32 ctrl_ext, txdctl, snoop; + s32 ret_val; + u16 i; + + e1000_initialize_hw_bits_ich8lan(hw); + + /* Initialize identification LED */ + ret_val = e1000e_id_led_init(hw); + if (ret_val) { + hw_dbg(hw, "Error initializing identification LED\n"); + return ret_val; + } + + /* Setup the receive address. */ + e1000e_init_rx_addrs(hw, mac->rar_entry_count); + + /* Zero out the Multicast HASH table */ + hw_dbg(hw, "Zeroing the MTA\n"); + for (i = 0; i < mac->mta_reg_count; i++) + E1000_WRITE_REG_ARRAY(hw, E1000_MTA, i, 0); + + /* Setup link and flow control */ + ret_val = e1000_setup_link_ich8lan(hw); + + /* Set the transmit descriptor write-back policy for both queues */ + txdctl = er32(TXDCTL); + txdctl = (txdctl & ~E1000_TXDCTL_WTHRESH) | + E1000_TXDCTL_FULL_TX_DESC_WB; + txdctl = (txdctl & ~E1000_TXDCTL_PTHRESH) | + E1000_TXDCTL_MAX_TX_DESC_PREFETCH; + ew32(TXDCTL, txdctl); + txdctl = er32(TXDCTL1); + txdctl = (txdctl & ~E1000_TXDCTL_WTHRESH) | + E1000_TXDCTL_FULL_TX_DESC_WB; + txdctl = (txdctl & ~E1000_TXDCTL_PTHRESH) | + E1000_TXDCTL_MAX_TX_DESC_PREFETCH; + ew32(TXDCTL1, txdctl); + + /* ICH8 has opposite polarity of no_snoop bits. + * By default, we should use snoop behavior. */ + if (mac->type == e1000_ich8lan) + snoop = PCIE_ICH8_SNOOP_ALL; + else + snoop = (u32) ~(PCIE_NO_SNOOP_ALL); + e1000e_set_pcie_no_snoop(hw, snoop); + + ctrl_ext = er32(CTRL_EXT); + ctrl_ext |= E1000_CTRL_EXT_RO_DIS; + ew32(CTRL_EXT, ctrl_ext); + + /* Clear all of the statistics registers (clear on read). It is + * important that we do this after we have tried to establish link + * because the symbol error count will increment wildly if there + * is no link. + */ + e1000_clear_hw_cntrs_ich8lan(hw); + + return 0; +} +/** + * e1000_initialize_hw_bits_ich8lan - Initialize required hardware bits + * @hw: pointer to the HW structure + * + * Sets/Clears required hardware bits necessary for correctly setting up the + * hardware for transmit and receive. + **/ +static void e1000_initialize_hw_bits_ich8lan(struct e1000_hw *hw) +{ + u32 reg; + + /* Extended Device Control */ + reg = er32(CTRL_EXT); + reg |= (1 << 22); + ew32(CTRL_EXT, reg); + + /* Transmit Descriptor Control 0 */ + reg = er32(TXDCTL); + reg |= (1 << 22); + ew32(TXDCTL, reg); + + /* Transmit Descriptor Control 1 */ + reg = er32(TXDCTL1); + reg |= (1 << 22); + ew32(TXDCTL1, reg); + + /* Transmit Arbitration Control 0 */ + reg = er32(TARC0); + if (hw->mac.type == e1000_ich8lan) + reg |= (1 << 28) | (1 << 29); + reg |= (1 << 23) | (1 << 24) | (1 << 26) | (1 << 27); + ew32(TARC0, reg); + + /* Transmit Arbitration Control 1 */ + reg = er32(TARC1); + if (er32(TCTL) & E1000_TCTL_MULR) + reg &= ~(1 << 28); + else + reg |= (1 << 28); + reg |= (1 << 24) | (1 << 26) | (1 << 30); + ew32(TARC1, reg); + + /* Device Status */ + if (hw->mac.type == e1000_ich8lan) { + reg = er32(STATUS); + reg &= ~(1 << 31); + ew32(STATUS, reg); + } +} + +/** + * e1000_setup_link_ich8lan - Setup flow control and link settings + * @hw: pointer to the HW structure + * + * Determines which flow control settings to use, then configures flow + * control. Calls the appropriate media-specific link configuration + * function. Assuming the adapter has a valid link partner, a valid link + * should be established. Assumes the hardware has previously been reset + * and the transmitter and receiver are not enabled. + **/ +static s32 e1000_setup_link_ich8lan(struct e1000_hw *hw) +{ + struct e1000_mac_info *mac = &hw->mac; + s32 ret_val; + + if (e1000_check_reset_block(hw)) + return 0; + + /* ICH parts do not have a word in the NVM to determine + * the default flow control setting, so we explicitly + * set it to full. + */ + if (mac->fc == e1000_fc_default) + mac->fc = e1000_fc_full; + + mac->original_fc = mac->fc; + + hw_dbg(hw, "After fix-ups FlowControl is now = %x\n", mac->fc); + + /* Continue to configure the copper link. */ + ret_val = e1000_setup_copper_link_ich8lan(hw); + if (ret_val) + return ret_val; + + ew32(FCTTV, mac->fc_pause_time); + + return e1000e_set_fc_watermarks(hw); +} + +/** + * e1000_setup_copper_link_ich8lan - Configure MAC/PHY interface + * @hw: pointer to the HW structure + * + * Configures the kumeran interface to the PHY to wait the appropriate time + * when polling the PHY, then call the generic setup_copper_link to finish + * configuring the copper link. + **/ +static s32 e1000_setup_copper_link_ich8lan(struct e1000_hw *hw) +{ + u32 ctrl; + s32 ret_val; + u16 reg_data; + + ctrl = er32(CTRL); + ctrl |= E1000_CTRL_SLU; + ctrl &= ~(E1000_CTRL_FRCSPD | E1000_CTRL_FRCDPX); + ew32(CTRL, ctrl); + + /* Set the mac to wait the maximum time between each iteration + * and increase the max iterations when polling the phy; + * this fixes erroneous timeouts at 10Mbps. */ + ret_val = e1000e_write_kmrn_reg(hw, GG82563_REG(0x34, 4), 0xFFFF); + if (ret_val) + return ret_val; + ret_val = e1000e_read_kmrn_reg(hw, GG82563_REG(0x34, 9), ®_data); + if (ret_val) + return ret_val; + reg_data |= 0x3F; + ret_val = e1000e_write_kmrn_reg(hw, GG82563_REG(0x34, 9), reg_data); + if (ret_val) + return ret_val; + + if (hw->phy.type == e1000_phy_igp_3) { + ret_val = e1000e_copper_link_setup_igp(hw); + if (ret_val) + return ret_val; + } + + return e1000e_setup_copper_link(hw); +} + +/** + * e1000_get_link_up_info_ich8lan - Get current link speed and duplex + * @hw: pointer to the HW structure + * @speed: pointer to store current link speed + * @duplex: pointer to store the current link duplex + * + * Calls the generic get_speed_and_duplex to retreive the current link + * information and then calls the Kumeran lock loss workaround for links at + * gigabit speeds. + **/ +static s32 e1000_get_link_up_info_ich8lan(struct e1000_hw *hw, u16 *speed, + u16 *duplex) +{ + s32 ret_val; + + ret_val = e1000e_get_speed_and_duplex_copper(hw, speed, duplex); + if (ret_val) + return ret_val; + + if ((hw->mac.type == e1000_ich8lan) && + (hw->phy.type == e1000_phy_igp_3) && + (*speed == SPEED_1000)) { + ret_val = e1000_kmrn_lock_loss_workaround_ich8lan(hw); + } + + return ret_val; +} + +/** + * e1000_kmrn_lock_loss_workaround_ich8lan - Kumeran workaround + * @hw: pointer to the HW structure + * + * Work-around for 82566 Kumeran PCS lock loss: + * On link status change (i.e. PCI reset, speed change) and link is up and + * speed is gigabit- + * 0) if workaround is optionally disabled do nothing + * 1) wait 1ms for Kumeran link to come up + * 2) check Kumeran Diagnostic register PCS lock loss bit + * 3) if not set the link is locked (all is good), otherwise... + * 4) reset the PHY + * 5) repeat up to 10 times + * Note: this is only called for IGP3 copper when speed is 1gb. + **/ +static s32 e1000_kmrn_lock_loss_workaround_ich8lan(struct e1000_hw *hw) +{ + struct e1000_dev_spec_ich8lan *dev_spec = &hw->dev_spec.ich8lan; + u32 phy_ctrl; + s32 ret_val; + u16 i, data; + bool link; + + if (!dev_spec->kmrn_lock_loss_workaround_enabled) + return 0; + + /* Make sure link is up before proceeding. If not just return. + * Attempting this while link is negotiating fouled up link + * stability */ + ret_val = e1000e_phy_has_link_generic(hw, 1, 0, &link); + if (!link) + return 0; + + for (i = 0; i < 10; i++) { + /* read once to clear */ + ret_val = e1e_rphy(hw, IGP3_KMRN_DIAG, &data); + if (ret_val) + return ret_val; + /* and again to get new status */ + ret_val = e1e_rphy(hw, IGP3_KMRN_DIAG, &data); + if (ret_val) + return ret_val; + + /* check for PCS lock */ + if (!(data & IGP3_KMRN_DIAG_PCS_LOCK_LOSS)) + return 0; + + /* Issue PHY reset */ + e1000_phy_hw_reset(hw); + mdelay(5); + } + /* Disable GigE link negotiation */ + phy_ctrl = er32(PHY_CTRL); + phy_ctrl |= (E1000_PHY_CTRL_GBE_DISABLE | + E1000_PHY_CTRL_NOND0A_GBE_DISABLE); + ew32(PHY_CTRL, phy_ctrl); + + /* Call gig speed drop workaround on Giga disable before accessing + * any PHY registers */ + e1000e_gig_downshift_workaround_ich8lan(hw); + + /* unable to acquire PCS lock */ + return -E1000_ERR_PHY; +} + +/** + * e1000_set_kmrn_lock_loss_workaound_ich8lan - Set Kumeran workaround state + * @hw: pointer to the HW structure + * @state: boolean value used to set the current Kumaran workaround state + * + * If ICH8, set the current Kumeran workaround state (enabled - TRUE + * /disabled - FALSE). + **/ +void e1000e_set_kmrn_lock_loss_workaround_ich8lan(struct e1000_hw *hw, + bool state) +{ + struct e1000_dev_spec_ich8lan *dev_spec = &hw->dev_spec.ich8lan; + + if (hw->mac.type != e1000_ich8lan) { + hw_dbg(hw, "Workaround applies to ICH8 only.\n"); + return; + } + + dev_spec->kmrn_lock_loss_workaround_enabled = state; +} + +/** + * e1000_ipg3_phy_powerdown_workaround_ich8lan - Power down workaround on D3 + * @hw: pointer to the HW structure + * + * Workaround for 82566 power-down on D3 entry: + * 1) disable gigabit link + * 2) write VR power-down enable + * 3) read it back + * Continue if successful, else issue LCD reset and repeat + **/ +void e1000e_igp3_phy_powerdown_workaround_ich8lan(struct e1000_hw *hw) +{ + u32 reg; + u16 data; + u8 retry = 0; + + if (hw->phy.type != e1000_phy_igp_3) + return; + + /* Try the workaround twice (if needed) */ + do { + /* Disable link */ + reg = er32(PHY_CTRL); + reg |= (E1000_PHY_CTRL_GBE_DISABLE | + E1000_PHY_CTRL_NOND0A_GBE_DISABLE); + ew32(PHY_CTRL, reg); + + /* Call gig speed drop workaround on Giga disable before + * accessing any PHY registers */ + if (hw->mac.type == e1000_ich8lan) + e1000e_gig_downshift_workaround_ich8lan(hw); + + /* Write VR power-down enable */ + e1e_rphy(hw, IGP3_VR_CTRL, &data); + data &= ~IGP3_VR_CTRL_DEV_POWERDOWN_MODE_MASK; + e1e_wphy(hw, IGP3_VR_CTRL, data | IGP3_VR_CTRL_MODE_SHUTDOWN); + + /* Read it back and test */ + e1e_rphy(hw, IGP3_VR_CTRL, &data); + data &= IGP3_VR_CTRL_DEV_POWERDOWN_MODE_MASK; + if ((data == IGP3_VR_CTRL_MODE_SHUTDOWN) || retry) + break; + + /* Issue PHY reset and repeat at most one more time */ + reg = er32(CTRL); + ew32(CTRL, reg | E1000_CTRL_PHY_RST); + retry++; + } while (retry); +} + +/** + * e1000e_gig_downshift_workaround_ich8lan - WoL from S5 stops working + * @hw: pointer to the HW structure + * + * Steps to take when dropping from 1Gb/s (eg. link cable removal (LSC), + * LPLU, Giga disable, MDIC PHY reset): + * 1) Set Kumeran Near-end loopback + * 2) Clear Kumeran Near-end loopback + * Should only be called for ICH8[m] devices with IGP_3 Phy. + **/ +void e1000e_gig_downshift_workaround_ich8lan(struct e1000_hw *hw) +{ + s32 ret_val; + u16 reg_data; + + if ((hw->mac.type != e1000_ich8lan) || + (hw->phy.type != e1000_phy_igp_3)) + return; + + ret_val = e1000e_read_kmrn_reg(hw, E1000_KMRNCTRLSTA_DIAG_OFFSET, + ®_data); + if (ret_val) + return; + reg_data |= E1000_KMRNCTRLSTA_DIAG_NELPBK; + ret_val = e1000e_write_kmrn_reg(hw, E1000_KMRNCTRLSTA_DIAG_OFFSET, + reg_data); + if (ret_val) + return; + reg_data &= ~E1000_KMRNCTRLSTA_DIAG_NELPBK; + ret_val = e1000e_write_kmrn_reg(hw, E1000_KMRNCTRLSTA_DIAG_OFFSET, + reg_data); +} + +/** + * e1000_cleanup_led_ich8lan - Restore the default LED operation + * @hw: pointer to the HW structure + * + * Return the LED back to the default configuration. + **/ +static s32 e1000_cleanup_led_ich8lan(struct e1000_hw *hw) +{ + if (hw->phy.type == e1000_phy_ife) + return e1e_wphy(hw, IFE_PHY_SPECIAL_CONTROL_LED, 0); + + ew32(LEDCTL, hw->mac.ledctl_default); + return 0; +} + +/** + * e1000_led_on_ich8lan - Turn LED's on + * @hw: pointer to the HW structure + * + * Turn on the LED's. + **/ +static s32 e1000_led_on_ich8lan(struct e1000_hw *hw) +{ + if (hw->phy.type == e1000_phy_ife) + return e1e_wphy(hw, IFE_PHY_SPECIAL_CONTROL_LED, + (IFE_PSCL_PROBE_MODE | IFE_PSCL_PROBE_LEDS_ON)); + + ew32(LEDCTL, hw->mac.ledctl_mode2); + return 0; +} + +/** + * e1000_led_off_ich8lan - Turn LED's off + * @hw: pointer to the HW structure + * + * Turn off the LED's. + **/ +static s32 e1000_led_off_ich8lan(struct e1000_hw *hw) +{ + if (hw->phy.type == e1000_phy_ife) + return e1e_wphy(hw, IFE_PHY_SPECIAL_CONTROL_LED, + (IFE_PSCL_PROBE_MODE | IFE_PSCL_PROBE_LEDS_OFF)); + + ew32(LEDCTL, hw->mac.ledctl_mode1); + return 0; +} + +/** + * e1000_clear_hw_cntrs_ich8lan - Clear statistical counters + * @hw: pointer to the HW structure + * + * Clears hardware counters specific to the silicon family and calls + * clear_hw_cntrs_generic to clear all general purpose counters. + **/ +static void e1000_clear_hw_cntrs_ich8lan(struct e1000_hw *hw) +{ + u32 temp; + + e1000e_clear_hw_cntrs_base(hw); + + temp = er32(ALGNERRC); + temp = er32(RXERRC); + temp = er32(TNCRS); + temp = er32(CEXTERR); + temp = er32(TSCTC); + temp = er32(TSCTFC); + + temp = er32(MGTPRC); + temp = er32(MGTPDC); + temp = er32(MGTPTC); + + temp = er32(IAC); + temp = er32(ICRXOC); + +} + +static struct e1000_mac_operations ich8_mac_ops = { + .mng_mode_enab = E1000_ICH_MNG_IAMT_MODE << E1000_FWSM_MODE_SHIFT, + .check_for_link = e1000e_check_for_copper_link, + .cleanup_led = e1000_cleanup_led_ich8lan, + .clear_hw_cntrs = e1000_clear_hw_cntrs_ich8lan, + .get_bus_info = e1000_get_bus_info_ich8lan, + .get_link_up_info = e1000_get_link_up_info_ich8lan, + .led_on = e1000_led_on_ich8lan, + .led_off = e1000_led_off_ich8lan, + .mc_addr_list_update = e1000e_mc_addr_list_update_generic, + .reset_hw = e1000_reset_hw_ich8lan, + .init_hw = e1000_init_hw_ich8lan, + .setup_link = e1000_setup_link_ich8lan, + .setup_physical_interface= e1000_setup_copper_link_ich8lan, +}; + +static struct e1000_phy_operations ich8_phy_ops = { + .acquire_phy = e1000_acquire_swflag_ich8lan, + .check_reset_block = e1000_check_reset_block_ich8lan, + .commit_phy = NULL, + .force_speed_duplex = e1000_phy_force_speed_duplex_ich8lan, + .get_cfg_done = e1000e_get_cfg_done, + .get_cable_length = e1000e_get_cable_length_igp_2, + .get_phy_info = e1000_get_phy_info_ich8lan, + .read_phy_reg = e1000e_read_phy_reg_igp, + .release_phy = e1000_release_swflag_ich8lan, + .reset_phy = e1000_phy_hw_reset_ich8lan, + .set_d0_lplu_state = e1000_set_d0_lplu_state_ich8lan, + .set_d3_lplu_state = e1000_set_d3_lplu_state_ich8lan, + .write_phy_reg = e1000e_write_phy_reg_igp, +}; + +static struct e1000_nvm_operations ich8_nvm_ops = { + .acquire_nvm = e1000_acquire_swflag_ich8lan, + .read_nvm = e1000_read_nvm_ich8lan, + .release_nvm = e1000_release_swflag_ich8lan, + .update_nvm = e1000_update_nvm_checksum_ich8lan, + .valid_led_default = e1000_valid_led_default_ich8lan, + .validate_nvm = e1000_validate_nvm_checksum_ich8lan, + .write_nvm = e1000_write_nvm_ich8lan, +}; + +struct e1000_info e1000_ich8_info = { + .mac = e1000_ich8lan, + .flags = FLAG_HAS_WOL + | FLAG_RX_CSUM_ENABLED + | FLAG_HAS_CTRLEXT_ON_LOAD + | FLAG_HAS_AMT + | FLAG_HAS_FLASH + | FLAG_APME_IN_WUC, + .pba = 8, + .get_invariants = e1000_get_invariants_ich8lan, + .mac_ops = &ich8_mac_ops, + .phy_ops = &ich8_phy_ops, + .nvm_ops = &ich8_nvm_ops, +}; + +struct e1000_info e1000_ich9_info = { + .mac = e1000_ich9lan, + .flags = FLAG_HAS_JUMBO_FRAMES + | FLAG_HAS_WOL + | FLAG_RX_CSUM_ENABLED + | FLAG_HAS_CTRLEXT_ON_LOAD + | FLAG_HAS_AMT + | FLAG_HAS_ERT + | FLAG_HAS_FLASH + | FLAG_APME_IN_WUC, + .pba = 10, + .get_invariants = e1000_get_invariants_ich8lan, + .mac_ops = &ich8_mac_ops, + .phy_ops = &ich8_phy_ops, + .nvm_ops = &ich8_nvm_ops, +}; + |