diff options
Diffstat (limited to 'arch/arm/plat-omap/include/mach/entry-macro.S')
| -rw-r--r-- | arch/arm/plat-omap/include/mach/entry-macro.S | 46 |
1 files changed, 44 insertions, 2 deletions
diff --git a/arch/arm/plat-omap/include/mach/entry-macro.S b/arch/arm/plat-omap/include/mach/entry-macro.S index 33256a0e9a28..00f45c01390d 100644 --- a/arch/arm/plat-omap/include/mach/entry-macro.S +++ b/arch/arm/plat-omap/include/mach/entry-macro.S @@ -3,6 +3,9 @@ * * Low-level IRQ helper macros for OMAP-based platforms * + * Copyright (C) 2009 Texas Instruments + * Added OMAP4 support - Santosh Shilimkar <santosh.shilimkar@ti.com> + * * This file is licensed under the terms of the GNU General Public * License version 2. This program is licensed "as is" without any * warranty of any kind, whether express or implied. @@ -10,6 +13,7 @@ #include <mach/hardware.h> #include <mach/io.h> #include <mach/irqs.h> +#include <asm/hardware/gic.h> #if defined(CONFIG_ARCH_OMAP1) @@ -56,7 +60,8 @@ .endm #endif -#if defined(CONFIG_ARCH_OMAP24XX) || defined(CONFIG_ARCH_OMAP34XX) +#if defined(CONFIG_ARCH_OMAP24XX) || defined(CONFIG_ARCH_OMAP34XX) || \ + defined(CONFIG_ARCH_OMAP4) #include <mach/omap24xx.h> #include <mach/omap34xx.h> @@ -67,7 +72,9 @@ #elif defined(CONFIG_ARCH_OMAP34XX) #define OMAP2_VA_IC_BASE IO_ADDRESS(OMAP34XX_IC_BASE) #endif - +#if defined(CONFIG_ARCH_OMAP4) +#include <mach/omap44xx.h> +#endif #define INTCPS_SIR_IRQ_OFFSET 0x0040 /* Active interrupt offset */ #define ACTIVEIRQ_MASK 0x7f /* Active interrupt bits */ @@ -80,6 +87,7 @@ .macro arch_ret_to_user, tmp1, tmp2 .endm +#ifndef CONFIG_ARCH_OMAP4 .macro get_irqnr_and_base, irqnr, irqstat, base, tmp ldr \base, =OMAP2_VA_IC_BASE ldr \irqnr, [\base, #0x98] /* IRQ pending reg 1 */ @@ -95,6 +103,40 @@ and \irqnr, \irqnr, #ACTIVEIRQ_MASK /* Clear spurious bits */ .endm +#else + /* + * The interrupt numbering scheme is defined in the + * interrupt controller spec. To wit: + * + * Interrupts 0-15 are IPI + * 16-28 are reserved + * 29-31 are local. We allow 30 to be used for the watchdog. + * 32-1020 are global + * 1021-1022 are reserved + * 1023 is "spurious" (no interrupt) + * + * For now, we ignore all local interrupts so only return an + * interrupt if it's between 30 and 1020. The test_for_ipi + * routine below will pick up on IPIs. + * A simple read from the controller will tell us the number + * of the highest priority enabled interrupt. + * We then just need to check whether it is in the + * valid range for an IRQ (30-1020 inclusive). + */ + .macro get_irqnr_and_base, irqnr, irqstat, base, tmp + ldr \base, =OMAP44XX_VA_GIC_CPU_BASE + ldr \irqstat, [\base, #GIC_CPU_INTACK] + + ldr \tmp, =1021 + + bic \irqnr, \irqstat, #0x1c00 + + cmp \irqnr, #29 + cmpcc \irqnr, \irqnr + cmpne \irqnr, \tmp + cmpcs \irqnr, \irqnr + .endm +#endif .macro irq_prio_table .endm |