path: root/gs/base/gxcldev.h

/* Copyright (C) 2001-2006 Artifex Software, Inc.
   All Rights Reserved.
  
   This software is provided AS-IS with no warranty, either express or
   implied.

   This software is distributed under license and may not be copied, modified
   or distributed except as expressly authorized under the terms of that
   license.  Refer to licensing information at http://www.artifex.com/
   or contact Artifex Software, Inc.,  7 Mt. Lassen Drive - Suite A-134,
   San Rafael, CA  94903, U.S.A., +1(415)492-9861, for further information.
*/

/*$Id$ */
/* Internal definitions for Ghostscript command lists. */

#ifndef gxcldev_INCLUDED
#  define gxcldev_INCLUDED

#include "gxclist.h"
#include "gsropt.h"
#include "gxht.h"		/* for gxdht.h */
#include "gxtmap.h"		/* ditto */
#include "gxdht.h"		/* for halftones */
#include "strimpl.h"		/* for compressed bitmaps */
#include "scfx.h"		/* ditto */
#include "srlx.h"		/* ditto */
#include "gsdcolor.h"

/* ---------------- Commands ---------------- */

/* Define the compression modes for bitmaps. */
/*#define cmd_compress_none 0 *//* (implicit) */
#define cmd_compress_rle 1
#define cmd_compress_cfe 2
#define cmd_mask_compress_any\
  ((1 << cmd_compress_rle) | (1 << cmd_compress_cfe))
/* Exported by gxclutil.c */
void clist_rle_init(stream_RLE_state *ss);
void clist_rld_init(stream_RLD_state *ss);
void clist_cfe_init(stream_CFE_state *ss, int width, gs_memory_t *mem);
void clist_cfd_init(stream_CFD_state *ss, int width, int height,
		    gs_memory_t *mem);

/*
 * A command always consists of an operation followed by operands;
 * the syntax of the operands depends on the operation.
 * In the operation definitions below:
 *      + (prefixed) means the operand is in the low 4 bits of the opcode.
 *      # means a variable-size operand encoded with the variable-size
 *         integer encoding.
 *      % means a variable-size operand encoded with the variable-size
 *         fixed coordinate encoding.
 *      $ means a color sized according to the device depth.
 *      <> means the operand size depends on other state information
 *         and/or previous operands.
 */
typedef enum {
    cmd_op_misc = 0x00,		/* (see below) */
    cmd_opv_end_run = 0x00,	/* (nothing) */
    cmd_opv_set_tile_size = 0x01,   /* rs?(1)nry?(1)nrx?(1)depth(5, encoded), */
				/* rep_width#, rep_height#, */
				/* [, nreps_x#][, nreps_y #] */
				/* [, rep_shift#] */
    cmd_opv_set_tile_phase = 0x02,	/* x#, y# */
    cmd_opv_set_tile_bits = 0x03,	/* index#, offset#, <bits> */
    cmd_opv_set_bits = 0x04,	/* depth*4+compress, width#, height#, */
				/* index#, offset#, <bits> */
    cmd_opv_set_tile_color = 0x05,	/* (nothing; next set/delta_color */
				/* refers to tile) */
    cmd_opv_set_misc = 0x06,
#define cmd_set_misc_lop (0 << 6)	/* 00: lop_lsb(6), lop_msb# */
#define cmd_set_misc_data_x (1 << 6)	/* 01: more(1)dx_lsb(5)[, dx_msb#] */
#define cmd_set_misc_map (2 << 6)	/* 10: contents(2)map_index(4) */
    /* [, n x frac] */
#define cmd_set_misc_halftone (3 << 6)	/* 11: type(6), num_comp# */
    cmd_opv_enable_lop = 0x07,	/* (nothing) */
    cmd_opv_disable_lop = 0x08,	/* (nothing) */
    /* obsolete */
    /* cmd_opv_set_ht_order = 0x09, */	/* component+1#[, cname#], */
				/* width#, height#, raster#, */
				/* shift#, num_levels#, num_bits#, */
				/* order_procs_index */
    /* obsolete */
    /* cmd_opv_set_ht_data = 0x0a, */	/* n, n x (uint|gx_ht_bit|ushort) */
    cmd_opv_end_page = 0x0b,	/* (nothing) */
    cmd_opv_delta_color0 = 0x0c,	/* See cmd_put_color in gxclutil.c */
    cmd_opv_delta_color1 = 0x0d,	/* <<same as color0>> */
    cmd_opv_set_copy_color = 0x0e,	/* (nothing) */
    cmd_opv_set_copy_alpha = 0x0f,	/* (nothing) */
    cmd_op_set_color0 = 0x10,	/* +n = number of low order zero bytes | */
#define cmd_no_color_index 15	/* +15 = transparent - "no color" */
    cmd_op_set_color1 = 0x20,	/* <<same as color0>> */
    cmd_op_fill_rect = 0x30,	/* +dy2dh2, x#, w# | +0, rect# */
    cmd_op_fill_rect_short = 0x40,	/* +dh, dx, dw | +0, rect_short */
    cmd_op_fill_rect_tiny = 0x50,	/* +dw+0, rect_tiny | +dw+8 */
    cmd_op_tile_rect = 0x60,	/* +dy2dh2, x#, w# | +0, rect# */
    cmd_op_tile_rect_short = 0x70,	/* +dh, dx, dw | +0, rect_short */
    cmd_op_tile_rect_tiny = 0x80,	/* +dw+0, rect_tiny | +dw+8 */
    cmd_op_copy_mono = 0x90,	/* +compress, x#, y#, (w+data_x)#, */
				/* h#, <bits> | */
#define cmd_copy_ht_color 4
				/* +4+compress, x#, y#, (w+data_x)#, */
				/* h#, <bits> | */
#define cmd_copy_use_tile 8
				/* +8 (use tile), x#, y# | */
				/* +12 (use tile), x#, y# */
    cmd_op_copy_color_alpha = 0xa0,	/* (same as copy_mono, except: */
				/* if color, ignore ht_color; */
				/* if alpha & !use_tile, depth is */
				/*   first operand) */
    cmd_op_delta_tile_index = 0xb0,	/* +delta+8 */
    cmd_op_set_tile_index = 0xc0	/* +index[11:8], index[7:0] */
} gx_cmd_op;

#define cmd_op_name_strings\
  "(misc)", "set_color[0]", "set_color[1]", "fill_rect",\
  "fill_rect_short", "fill_rect_tiny", "tile_rect", "tile_rect_short",\
  "tile_rect_tiny", "copy_mono", "copy_color_alpha", "delta_tile_index",\
  "set_tile_index", "(misc2)", "(segment)", "(path)"

#define cmd_misc_op_name_strings\
  "end_run", "set_tile_size", "set_tile_phase", "set_tile_bits",\
  "set_bits", "set_tile_color", "set_misc", "enable_lop",\
  "disable_lop", "set_ht_order", "set_ht_data", "end_page",\
  "delta2_color0", "delta2_color1", "set_copy_color", "set_copy_alpha",

#ifdef DEBUG
extern const char *const cmd_op_names[16];
extern const char *const *const cmd_sub_op_names[16];
#endif

/*
 * Define the size of the largest command, not counting any bitmap or
 * similar variable-length operands.
 * The variable-size integer encoding is little-endian.  The low 7 bits
 * of each byte contain data; the top bit is 1 for all but the last byte.
 */
#define cmd_max_intsize(siz)\
  (((siz) * 8 + 6) / 7)
#define cmd_largest_size\
  (2 + (1 + cmd_max_dash) * sizeof(float))

/* ---------------- Command parameters ---------------- */

/* Rectangle */
typedef struct {
    int x, y, width, height;
} gx_cmd_rect;

/* Short rectangle */
typedef struct {
    byte dx, dwidth, dy, dheight;	/* dy and dheight are optional */
} gx_cmd_rect_short;

#define cmd_min_short (-128)
#define cmd_max_short 127
/* Tiny rectangle */
#define cmd_min_dw_tiny (-4)
#define cmd_max_dw_tiny 3
typedef struct {
    unsigned dx:4;
    unsigned dy:4;
} gx_cmd_rect_tiny;

#define cmd_min_dxy_tiny (-8)
#define cmd_max_dxy_tiny 7

/*
 * Encoding for tile depth information.
 *
 * The cmd_opv_set_tile_size command code stores tile depth information
 * as part of the first byte following the command code. Only 5 bits of
 * this byte are available, which held the value depth - 1. The DeviceN
 * code requires depths of > 32 bits, so a new encoding is required. The
 * encoding selected represents depth information either directly (for
 * depth <= 15), or as a multiple of 8. The high-order bit determines
 * which is the case; it is cleared if the depth is represented directly,
 * and set if the depth is represented as a multiple of 8.
 */
#define cmd_depth_to_code(d)    ((d) > 0xf ? 0x10 | ((d) >> 3) : (d))
#define cmd_code_to_depth(v)    \
    (((v) & 0x10) != 0 ? ((v) & 0xf) << 3 : (v) & 0xf)

/*
 * When we write bitmaps, we remove raster padding selectively:
 *      - If the bitmap is compressed, we don't remove any padding;
 *      - If the width is <= 6 bytes, we remove all the padding;
 *      - If the bitmap is only 1 scan line high, we remove the padding;
 *      - If the bitmap is going to be replicated horizontally (see the
 *      definition of decompress_spread below), we remove the padding;
 *      - Otherwise, we remove the padding only from the last scan line.
 */
#define cmd_max_short_width_bytes 6
#define cmd_max_short_width_bits (cmd_max_short_width_bytes * 8)
/*
 * Determine the (possibly unpadded) width in bytes for writing a bitmap,
 * per the algorithm just outlined.  If compression_mask has any of the
 * cmd_mask_compress_any bits set, we assume the bitmap will be compressed.
 * Return the total size of the bitmap.
 */
uint clist_bitmap_bytes(uint width_bits, uint height,
			int compression_mask,
			uint * width_bytes, uint * raster);

/*
 * For halftone cells, we always write an unreplicated bitmap, but we
 * reserve cache space for the reading pass based on the replicated size.
 * See the clist_change_tile procedure for the algorithm that chooses the
 * replication factors.
 */

/* ---------------- Block file entries ---------------- */

typedef struct cmd_block_s {
    int band_min, band_max;
#define cmd_band_end (-1)	/* end of band file */
    int64_t pos;		/* starting position in cfile */
    gx_band_complexity_t band_complexity;  
    
} cmd_block;

/* ---------------- Band state ---------------- */

/* Remember the current state of one band when writing or reading. */
struct gx_clist_state_s {
    gx_color_index colors[2];	/* most recent colors */
    gx_device_color_saved sdc;  /* last device color for this band */
    uint tile_index;		/* most recent tile index */
    gx_bitmap_id tile_id;	/* most recent tile id */
/* Since tile table entries may be deleted and/or moved at any time, */
/* the following is the only reliable way to check whether tile_index */
/* references a particular tile id: */
#define cls_has_tile_id(cldev, pcls, tid, offset_temp)\
  ((pcls)->tile_id == (tid) &&\
   (offset_temp = cldev->tile_table[(pcls)->tile_index].offset) != 0 &&\
   ((tile_slot *)(cldev->data + offset_temp))->id == (tid))
    gs_id pattern_id;		/* the last stored pattern id. */
    gs_int_point tile_phase;	/* most recent tile phase */
    gx_color_index tile_colors[2];	/* most recent tile colors */
    gx_cmd_rect rect;		/* most recent rectangle */
    gs_logical_operation_t lop;	/* most recent logical op */
    short lop_enabled;		/* 0 = don't use lop, 1 = use lop, */
				/* -1 is used internally */
    short clip_enabled;		/* 0 = don't clip, 1 = do clip, */
				/* -1 is used internally */
    bool color_is_alpha;	/* for copy_color_alpha */
    uint known;			/* flags for whether this band */
				/* knows various misc. parameters */
    /* We assign 'known' flags here from the high end; */
    /* gxclpath.h assigns them from the low end. */
#define tile_params_known (1<<15)
#define begin_image_known (1<<14) /* gxclimag.c */
#define initial_known 0x3fff	/* exclude tile & image params */
    /* Following are only used when writing */
    cmd_list list;		/* list of commands for band */
    /* Following are set when writing, read when reading */
    gx_band_complexity_t band_complexity; 
    gx_colors_used_t colors_used;
};

/* The initial values for a band state */
/*static const gx_clist_state cls_initial */
#define cls_initial_values\
	 { gx_no_color_index, gx_no_color_index },\
	{ gx_dc_type_none },\
	0, gx_no_bitmap_id, gs_no_id,\
	 { 0, 0 }, { gx_no_color_index, gx_no_color_index },\
	 { 0, 0, 0, 0 }, lop_default, 0, 0, 0, initial_known,\
	{ 0, 0 }, { 0, 0 }, { 0, 0 }

/* Define the size of the command buffer used for reading. */
/* This is needed to split up operations with a large amount of data, */
/* primarily large copy_ operations. */
#define cbuf_size 4096

/* ---------------- Driver procedures ---------------- */

/* In gxclrect.c */
dev_proc_fillpage(clist_fillpage);
dev_proc_fill_rectangle(clist_fill_rectangle);
dev_proc_copy_mono(clist_copy_mono);
dev_proc_copy_color(clist_copy_color);
dev_proc_copy_alpha(clist_copy_alpha);
dev_proc_strip_tile_rectangle(clist_strip_tile_rectangle);
dev_proc_strip_copy_rop(clist_strip_copy_rop);
dev_proc_fill_trapezoid(clist_fill_trapezoid);
dev_proc_fill_linear_color_trapezoid(clist_fill_linear_color_trapezoid);
dev_proc_fill_linear_color_triangle(clist_fill_linear_color_triangle);
dev_proc_dev_spec_op(clist_dev_spec_op);

/* In gxclimag.c */
dev_proc_fill_mask(clist_fill_mask);
dev_proc_begin_typed_image(clist_begin_typed_image);
dev_proc_create_compositor(clist_create_compositor);

/* In gxclread.c */
dev_proc_get_bits_rectangle(clist_get_bits_rectangle);

/* ---------------- Driver procedure support ---------------- */

/*
 * The procedures and macros defined here are used when writing
 * (gxclist.c, gxclbits.c, gxclimag.c, gxclpath.c, gxclrect.c).
 * Note that none of the cmd_put_xxx procedures do VMerror recovery;
 * they convert low-memory warnings to VMerror errors.
 */

/* ------ Exported by gxclist.c ------ */

/*
 * Error recovery procedures for writer-side VMerrors, for async rendering
 * support.  This logic assumes that the command list file and/or the
 * renderer allocate memory from the same pool as the writer. Hence, when
 * the writer runs out of memory, it tries to pause and let the renderer run
 * for a while in hope that enough memory will be freed by it to allow the
 * writer to allocate enough memory to proceed. Once a VMerror is detected,
 * error recovery proceeds in two escalating stages:
 *
 *  1) The recovery logic repeatedly calls clist_VMerror_recover(), which
 *     waits until the next page has finished rendering. The recovery logic
 *     keeps calling clist_VMerror_recover() until enough memory is freed,
 *     or until clist_VMerror_recover() signals that no more pages
 *     remain to be rendered (when return code < 0).
 *
 *  2) If enough memory is not free, the recovery logic calls
 *     clist_VMerror_recover_flush() once. This routine terminates and
 *     flushes out the partially-completed page that the writer is currently
 *     writing to the command file, then waits for the partial page to finish
 *     rendering. It then opens up a new command list "file" and resets the
 *     state of the command list machinery to an initial state as if a new
 *     page were beginning.
 *
 * If insufficient memory is available after the 2nd step, the situation
 * is the same as if it ocurred in a non-async setup: the writer program
 * simply used up too much memory and cannot continue.
 *
 * The first stage of error recovery (no flush) is performed without
 * flushing out the current page, so failing commands can simply be
 * restarted after such recovery. This is not true of 2nd stage recovery
 * (flush): as part of its operation, the flush resets the state of both
 * writer and renderer to initial values.  In this event, the recovery logic
 * which called clist_try_recover_VMerror_flush() must force any pertinent
 * state information to be re-emitted before re-issuing the failing command.
 *
 * In case of a VMerror, the internal procedures that support the driver
 * procedures simply return the error code: they do not attempt recovery.
 * Note that all such procedures must take care that (1) they don't update
 * any writer state to reflect information written to the band list unless
 * the write actually succeeds, and (2) they are idempotent, since they may
 * be re-executed after first-stage VMerror recovery.
 *
 * Error recovery is only performed by the driver procedures themselves
 * (fill_rectangle, copy_mono, fill_path, etc.) and a few other procedures
 * at the same level of control.  The implementation of error recovery is
 * packaged up in the FOR_RECTS et al macros defined below, but -- as noted
 * above -- recovery is not fully transparent.  Other routines which perform
 * error recovery are those which open the device, begin a new page, or
 * reopen the device (put_params).
 */
int clist_VMerror_recover(gx_device_clist_writer *, int);
int clist_VMerror_recover_flush(gx_device_clist_writer *, int);

/* Write out device parameters. */
int cmd_put_params(gx_device_clist_writer *, gs_param_list *);

/* Conditionally keep command statistics. */
#ifdef DEBUG
int cmd_count_op(int op, uint size);
void cmd_uncount_op(int op, uint size);
void cmd_print_stats(void);
#  define cmd_count_add1(v) (v++)
#else
#  define cmd_count_op(op, size) (op)
#  define cmd_uncount_op(op, size) DO_NOTHING
#  define cmd_count_add1(v) DO_NOTHING
#endif

/* Add a command to the appropriate band list, */
/* and allocate space for its data. */
byte *cmd_put_list_op(gx_device_clist_writer * cldev, cmd_list * pcl, uint size);

/* Request a space in the buffer. 
   Writes out the buffer if necessary.
   Returns the size of available space. */
int cmd_get_buffer_space(gx_device_clist_writer * cldev, gx_clist_state * pcls, uint size);

#ifdef DEBUG
byte *cmd_put_op(gx_device_clist_writer * cldev, gx_clist_state * pcls, uint size);
#else
#  define cmd_put_op(cldev, pcls, size)\
     cmd_put_list_op(cldev, &(pcls)->list, size)
#endif
/* Call cmd_put_op and update stats if no error occurs. */
#define set_cmd_put_op(dp, cldev, pcls, op, csize)\
  ( (dp = cmd_put_op(cldev, pcls, csize)) == 0 ?\
      (cldev)->error_code :\
    (*dp = cmd_count_op(op, csize), 0) )

/* Add a command for all bands or a range of bands. */
byte *cmd_put_range_op(gx_device_clist_writer * cldev, int band_min,
		       int band_max, uint size);

#define cmd_put_all_op(cldev, size)\
  cmd_put_range_op(cldev, 0, (cldev)->nbands - 1, size)
/* Call cmd_put_all/range_op and update stats if no error occurs. */
#define set_cmd_put_range_op(dp, cldev, op, bmin, bmax, csize)\
  ( (dp = cmd_put_range_op(cldev, bmin, bmax, csize)) == 0 ?\
      (cldev)->error_code :\
    (*dp = cmd_count_op(op, csize), 0) )
#define set_cmd_put_all_op(dp, cldev, op, csize)\
  set_cmd_put_range_op(dp, cldev, op, 0, (cldev)->nbands - 1, csize)

/* Shorten the last allocated command. */
/* Note that this does not adjust the statistics. */
#define cmd_shorten_list_op(cldev, pcls, delta)\
  ((pcls)->tail->size -= (delta), (cldev)->cnext -= (delta))
#define cmd_shorten_op(cldev, pcls, delta)\
  cmd_shorten_list_op(cldev, &(pcls)->list, delta)

/* Write out the buffered commands, and reset the buffer. */
/* Return 0 if OK, 1 if OK with low-memory warning, */
/* or the usual negative error code. */
int cmd_write_buffer(gx_device_clist_writer * cldev, byte cmd_end);

/* End a page by flushing the buffer and terminating the command list. */
int clist_end_page(gx_device_clist_writer *);

/* Compute the # of bytes required to represent a variable-size integer. */
/* (This works for negative integers also; they are written as though */
/* they were unsigned.) */
int cmd_size_w(uint);

#define w1byte(w) (!((w) & ~0x7f))
#define w2byte(w) (!((w) & ~0x3fff))
#define cmd_sizew(w)\
  (w1byte(w) ? 1 : w2byte(w) ? 2 : cmd_size_w((uint)(w)))
#define cmd_size2w(wx,wy)\
  (w1byte((wx) | (wy)) ? 2 :\
   cmd_size_w((uint)(wx)) + cmd_size_w((uint)(wy)))
#define cmd_sizexy(xy) cmd_size2w((xy).x, (xy).y)
#define cmd_sizew_max ((sizeof(uint) * 8 + 6) / 7)

/* Put a variable-size integer in the buffer. */
byte *cmd_put_w(uint, byte *);

#define cmd_putw(w,dp)\
  (w1byte(w) ? (*dp = w, ++dp) :\
   w2byte(w) ? (*dp = (w) | 0x80, dp[1] = (w) >> 7, dp += 2) :\
   (dp = cmd_put_w((uint)(w), dp)))
#define cmd_put2w(wx,wy,dp)\
  (w1byte((wx) | (wy)) ? (dp[0] = (wx), dp[1] = (wy), dp += 2) :\
   (dp = cmd_put_w((uint)(wy), cmd_put_w((uint)(wx), dp))))
#define cmd_putxy(xy,dp) cmd_put2w((xy).x, (xy).y, dp)

int cmd_size_frac31(register frac31 w);
byte * cmd_put_frac31(register frac31 w, register byte * dp);

/* Put out a command to set a color. */
typedef struct {
    byte set_op;
    byte delta_op;
    bool tile_color;
} clist_select_color_t;
extern const clist_select_color_t
      clist_select_color0, clist_select_color1, clist_select_tile_color0,
      clist_select_tile_color1;

/* See comments in gxclutil.c */
int cmd_put_color(gx_device_clist_writer * cldev, gx_clist_state * pcls,
                  const clist_select_color_t * select,
                  gx_color_index color, gx_color_index * pcolor);

extern const gx_color_index cmd_delta_offsets[];	/* In gxclutil.c */

#define cmd_set_color0(dev, pcls, color0)\
  cmd_put_color(dev, pcls, &clist_select_color0, color0, &(pcls)->colors[0])
#define cmd_set_color1(dev, pcls, color1)\
  cmd_put_color(dev, pcls, &clist_select_color1, color1, &(pcls)->colors[1])

/* Put out a command to set the tile colors. */
int cmd_set_tile_colors(gx_device_clist_writer *cldev, gx_clist_state * pcls,
			gx_color_index color0, gx_color_index color1);

/* Put out a command to set the tile phase. */
int
cmd_set_tile_phase_generic(gx_device_clist_writer * cldev, gx_clist_state * pcls,
		   int px, int py, bool all_bands);
int cmd_set_tile_phase(gx_device_clist_writer *cldev, gx_clist_state * pcls,
		       int px, int py);

/* Enable or disable the logical operation. */
int cmd_put_enable_lop(gx_device_clist_writer *, gx_clist_state *, int);
#define cmd_do_enable_lop(cldev, pcls, enable)\
  ( (pcls)->lop_enabled == ((enable) ^ 1) &&\
    cmd_put_enable_lop(cldev, pcls, enable) < 0 ?\
      (cldev)->error_code : 0 )
#define cmd_enable_lop(cldev, pcls)\
  cmd_do_enable_lop(cldev, pcls, 1)
#define cmd_disable_lop(cldev, pcls)\
  cmd_do_enable_lop(cldev, pcls, 0)

/* Enable or disable clipping. */
int cmd_put_enable_clip(gx_device_clist_writer *, gx_clist_state *, int);

#define cmd_do_enable_clip(cldev, pcls, enable)\
  ( (pcls)->clip_enabled == ((enable) ^ 1) &&\
    cmd_put_enable_clip(cldev, pcls, enable) < 0 ?\
      (cldev)->error_code : 0 )
#define cmd_enable_clip(cldev, pcls)\
  cmd_do_enable_clip(cldev, pcls, 1)
#define cmd_disable_clip(cldev, pcls)\
  cmd_do_enable_clip(cldev, pcls, 0)

/* Write a command to set the logical operation. */
int cmd_set_lop(gx_device_clist_writer *, gx_clist_state *,
		gs_logical_operation_t);

/* Disable (if default) or enable the logical operation, setting it if */
/* needed. */
int cmd_update_lop(gx_device_clist_writer *, gx_clist_state *,
		   gs_logical_operation_t);

/*
 * For dividing up an operation into bands, use the control pattern :
 * 
 *   cmd_rects_enum_t re;
 *   RECT_ENUM_INIT(re, ry, rheight);
 *   do {
 *	RECT_STEP_INIT(re);
 *	... process rectangle x, y, width, height in band pcls ...
 *
 *	........
 *	continue;
 * error_in_rect:
 *	if (!(cdev->error_is_retryable && cdev->driver_call_nesting == 0 &&
 *		SET_BAND_CODE(clist_VMerror_recover_flush(cdev, re.band_code)) >= 0))
 *	    return re.band_code;
 *	re.y -= re.height;
 *   } while ((re.y += re.height) < re.yend);
 *
 * Note that RECT_STEP_INIT(re) sets re.height.  It is OK for the code that
 * processes each band to reset height to a smaller (positive) value; the
 * vertical subdivision code in copy_mono, copy_color, and copy_alpha makes
 * use of this.  The band processing code may `continue' (to reduce nesting
 * of conditionals).
 *
 * The error_in_rect code detects an error that may be a recoverable
 * VMerror, with calling clist_VMerror_recover_flush. It will attempt to fix the
 * VMerror by flushing and closing the band and resetting the imager state,
 * and then restart emitting the entire band.
 * Note that re.y must not change when restarting the band.
 *
 * The band processing code may wrap a writing operation with a pattern like this : 
 *
 * 	do {
 *	    code = operation(...);
 *	} while (RECT_RECOVER(code));
 *	if (code < 0 && SET_BAND_CODE(code))
 *	    goto error_in_rect;
 *
 *
 * This will 
 * perform local first-stage VMerror recovery, by waiting for some memory to
 * become free and then retrying the failed operation starting at the
 * TRY_RECT. If local recovery is unsuccessful, the local recovery code
 * should pass control to error_in_rect.
 *
 * In a few cases, the band processing code calls other driver procedures
 * (e.g., clist_copy_mono calls itself recursively if it must split up the
 * operation into smaller pieces) or other procedures that may attempt
 * VMerror recovery.  In such cases, the recursive call must not attempt
 * second-stage VMerror recovery, since the caller would have no way of
 * knowing that the writer state had been reset.  Such recursive calls
 * should be wrapped in 
 *
 *  ++cdev->driver_call_nesting;  { ... } --cdev->driver_call_nesting;
 *
 * , which causes error_in_rect
 * simply to return the error code rather than attempting
 * recovery.  (The local recovery with do { ... } while (RECT_RECOVER(code));
 * is still allowed since it is transparent.) By
 * convention, calls to cmd_put_xxx or cmd_set_xxx never attempt recovery
 * and so never require  a nesting.
 *
 * If a put_params call fails, the device will be left in a closed state,
 * but higher-level code won't notice this fact.  We flag this by setting
 * permanent_error, which prevents writing to the command list.
 */

typedef struct cmd_rects_enum_s {
	int y;
	int height;
	int yend;
	int band_height;
	int band_code;
	int band;
	gx_clist_state *pcls;
	int band_end;
	int nbands;
} cmd_rects_enum_t;

#define RECT_ENUM_INIT(re, yvar, heightvar)\
	re.y = yvar;\
	re.height = heightvar;\
	re.yend = re.y + re.height;\
	re.band_height = cdev->page_band_height;\
	re.nbands = (re.yend - re.y + re.band_height - 1) / re.band_height;

#define RECT_STEP_INIT(re)\
	    re.band = re.y / re.band_height;\
	    re.pcls = cdev->states + re.band;\
	    re.band_end = (re.band + 1) * re.band_height;\
	    re.height = min(re.band_end, re.yend) - re.y;


#define RECT_RECOVER(codevar) (codevar < 0 && (codevar = clist_VMerror_recover(cdev, codevar)) >= 0)
#define SET_BAND_CODE(codevar) (re.band_code = codevar)

/* Read a transformation matrix. */
const byte *cmd_read_matrix(gs_matrix * pmat, const byte * cbp);


/* ------ Exported by gxclrect.c ------ */

/* Put out a fill or tile rectangle command. */
int cmd_write_rect_cmd(gx_device_clist_writer * cldev, gx_clist_state * pcls,
		       int op, int x, int y, int width, int height);

/* Put out a fill or tile rectangle command for fillpage. */
int cmd_write_page_rect_cmd(gx_device_clist_writer * cldev, int op);

/* ------ Exported by gxclbits.c ------ */

/*
 * Put a bitmap in the buffer, compressing if appropriate.
 * pcls == 0 means put the bitmap in all bands.
 * Return <0 if error, otherwise the compression method.
 * A return value of gs_error_limitcheck means that the bitmap was too big
 * to fit in the command reading buffer.
 * Note that this leaves room for the command and initial arguments,
 * but doesn't fill them in.
 *
 * If decompress_elsewhere is set in the compression_mask, it is OK
 * to write out a compressed bitmap whose decompressed size is too large
 * to fit in the command reading buffer.  (This is OK when reading a
 * cached bitmap, but not a bitmap for a one-time copy operation.)
 */
#define decompress_elsewhere 0x100
/*
 * If decompress_spread is set, the decompressed data will be spread out
 * for replication, so we drop all the padding even if the width is
 * greater than cmd_max_short_width_bytes (see above).
 */
#define decompress_spread 0x200

int cmd_put_bits(gx_device_clist_writer * cldev, gx_clist_state * pcls,
		 const byte * data, uint width_bits, uint height,
		 uint raster, int op_size, int compression_mask,
		 byte ** pdp, uint * psize);

/*
 * Put out commands for a color map (transfer function, black generation, or
 * undercolor removal).  If pid != 0, write the map only if its ID differs
 * from the current one, and update the saved ID in the case.
 */
typedef enum {
    cmd_map_transfer = 0,	/* all transfer functions */
    cmd_map_transfer_0,		/* transfer[0] */
    cmd_map_transfer_1,		/* transfer[1] */
    cmd_map_transfer_2,		/* transfer[2] */
    cmd_map_transfer_3,		/* transfer[3] */
    cmd_map_black_generation,
    cmd_map_undercolor_removal
} cmd_map_index;
typedef enum {
    cmd_map_none = 0,		/* no map, use default */
    cmd_map_identity,		/* identity map */
    cmd_map_other		/* other map */
} cmd_map_contents;
int cmd_put_color_map(gx_device_clist_writer * cldev,
                      cmd_map_index map_index, int comp_num,
                      const gx_transfer_map * map, gs_id * pid);

/*
 * Change tiles for clist_tile_rectangle.  (We make this a separate
 * procedure primarily for readability.)
 */
int clist_change_tile(gx_device_clist_writer * cldev, gx_clist_state * pcls,
		      const gx_strip_bitmap * tiles, int depth);

/*
 * Change "tile" for clist_copy_*.  Only uses tiles->{data, id, raster,
 * rep_width, rep_height}.  tiles->[rep_]shift must be zero.
 */
int clist_change_bits(gx_device_clist_writer * cldev, gx_clist_state * pcls,
		      const gx_strip_bitmap * tiles, int depth);

/* ------ Exported by gxclimag.c ------ */

/*
 * Write out any necessary color mapping data.
 */
int cmd_put_color_mapping(gx_device_clist_writer * cldev,
				  const gs_imager_state * pis);
/*
 * Add commands to represent a full (device) halftone.
 * (This routine should probably be in some other module.)
 */
int cmd_put_halftone(gx_device_clist_writer * cldev,
		     const gx_device_halftone * pdht);

/* ------ Exported by gxclrast.c for gxclread.c ------ */

/*
 * Define whether we are actually rendering a band, or just executing
 * the put_params that occurs at the beginning of each page.
 */
typedef enum {
    playback_action_render,
    playback_action_setup
} clist_playback_action;

/* Play back and rasterize one band. */
int clist_playback_band(clist_playback_action action,
			gx_device_clist_reader *cdev,
			stream *s, gx_device *target,
			int x0, int y0, gs_memory_t *mem);

/* Playback the band file, taking the indicated action w/ its contents. */
int clist_playback_file_bands(clist_playback_action action, 
			  gx_device_clist_reader *crdev,
			  gx_band_page_info_t *page_info, gx_device *target,
			  int band_first, int band_last, int x0, int y0);
#ifdef DEBUG 
int64_t clist_file_offset(const stream_state *st, uint buffer_offset);
int top_up_offset_map(stream_state * st, const byte *buf, const byte *ptr, const byte *end);
#endif

int clist_writer_push_no_cropping(gx_device_clist_writer *cdev);
int clist_writer_push_cropping(gx_device_clist_writer *cdev, int ry, int rheight);
int clist_writer_pop_cropping(gx_device_clist_writer *cdev);
int clist_writer_check_empty_cropping_stack(gx_device_clist_writer *cdev);
int clist_read_icctable(gx_device_clist_reader *crdev);

/* Special write out for the serialized icc profile table */

int cmd_write_icctable(gx_device_clist_writer * cldev, unsigned char *pbuf, int data_size);

/* Enumeration of psuedo band offsets for extra c-list data.
   This includes the ICC profile table and may later include
   compressed image data */

typedef enum {

    ICC_BAND_OFFSET = 1

} psuedoband_offset;

/* Enumeration of compositor actions for band cropping. */

typedef enum {
    ALLBANDS = 0,
    PUSHCROP,
    POPCROP,
    CURRBANDS,
    SAMEAS_PUSHCROP_BUTNOPUSH
} cl_crop_action;

#endif /* gxcldev_INCLUDED */