diff options
| -rw-r--r-- | Documentation/powerpc/booting-without-of.txt | 171 | ||||
| -rw-r--r-- | arch/powerpc/platforms/Kconfig | 11 | ||||
| -rw-r--r-- | arch/powerpc/sysdev/fsl_soc.c | 2 |
3 files changed, 183 insertions, 1 deletions
diff --git a/Documentation/powerpc/booting-without-of.txt b/Documentation/powerpc/booting-without-of.txt index 20e0e6cb034..a599f1a8a14 100644 --- a/Documentation/powerpc/booting-without-of.txt +++ b/Documentation/powerpc/booting-without-of.txt @@ -1510,7 +1510,10 @@ platforms are moved over to use the flattened-device-tree model. i) Freescale QUICC Engine module (QE) This represents qe module that is installed on PowerQUICC II Pro. - Hopefully it will merge backward compatibility with CPM/CPM2. + + NOTE: This is an interim binding; it should be updated to fit + in with the CPM binding later in this document. + Basically, it is a bus of devices, that could act more or less as a complete entity (UCC, USB etc ). All of them should be siblings on the "root" qe node, using the common properties from there. @@ -1848,6 +1851,172 @@ platforms are moved over to use the flattened-device-tree model. fsl,has-rstcr; }; + l) Freescale Communications Processor Module + + NOTE: This is an interim binding, and will likely change slightly, + as more devices are supported. The QE bindings especially are + incomplete. + + i) Root CPM node + + Properties: + - compatible : "fsl,cpm1", "fsl,cpm2", or "fsl,qe". + - reg : The first resource is a 48-byte region beginning with + CPCR. The second is the available general-purpose + DPRAM. + + Example: + cpm@119c0 { + #address-cells = <1>; + #size-cells = <1>; + #interrupt-cells = <2>; + compatible = "fsl,mpc8272-cpm", "fsl,cpm2"; + reg = <119c0 30 0 2000>; + } + + ii) Properties common to mulitple CPM/QE devices + + - fsl,cpm-command : This value is ORed with the opcode and command flag + to specify the device on which a CPM command operates. + + - fsl,cpm-brg : Indicates which baud rate generator the device + is associated with. If absent, an unused BRG + should be dynamically allocated. If zero, the + device uses an external clock rather than a BRG. + + - reg : Unless otherwise specified, the first resource represents the + scc/fcc/ucc registers, and the second represents the device's + parameter RAM region (if it has one). + + iii) Serial + + Currently defined compatibles: + - fsl,cpm1-smc-uart + - fsl,cpm2-smc-uart + - fsl,cpm1-scc-uart + - fsl,cpm2-scc-uart + - fsl,qe-uart + + Example: + + serial@11a00 { + device_type = "serial"; + compatible = "fsl,mpc8272-scc-uart", + "fsl,cpm2-scc-uart"; + reg = <11a00 20 8000 100>; + interrupts = <28 8>; + interrupt-parent = <&PIC>; + fsl,cpm-brg = <1>; + fsl,cpm-command = <00800000>; + }; + + iii) Network + + Currently defined compatibles: + - fsl,cpm1-scc-enet + - fsl,cpm2-scc-enet + - fsl,cpm1-fec-enet + - fsl,cpm2-fcc-enet (third resource is GFEMR) + - fsl,qe-enet + + Example: + + ethernet@11300 { + device_type = "network"; + compatible = "fsl,mpc8272-fcc-enet", + "fsl,cpm2-fcc-enet"; + reg = <11300 20 8400 100 11390 1>; + local-mac-address = [ 00 00 00 00 00 00 ]; + interrupts = <20 8>; + interrupt-parent = <&PIC>; + phy-handle = <&PHY0>; + linux,network-index = <0>; + fsl,cpm-command = <12000300>; + }; + + iv) MDIO + + Currently defined compatibles: + fsl,pq1-fec-mdio (reg is same as first resource of FEC device) + fsl,cpm2-mdio-bitbang (reg is port C registers) + + Properties for fsl,cpm2-mdio-bitbang: + fsl,mdio-pin : pin of port C controlling mdio data + fsl,mdc-pin : pin of port C controlling mdio clock + + Example: + + mdio@10d40 { + device_type = "mdio"; + compatible = "fsl,mpc8272ads-mdio-bitbang", + "fsl,mpc8272-mdio-bitbang", + "fsl,cpm2-mdio-bitbang"; + reg = <10d40 14>; + #address-cells = <1>; + #size-cells = <0>; + fsl,mdio-pin = <12>; + fsl,mdc-pin = <13>; + }; + + v) Baud Rate Generators + + Currently defined compatibles: + fsl,cpm-brg + fsl,cpm1-brg + fsl,cpm2-brg + + Properties: + - reg : There may be an arbitrary number of reg resources; BRG + numbers are assigned to these in order. + - clock-frequency : Specifies the base frequency driving + the BRG. + + Example: + + brg@119f0 { + compatible = "fsl,mpc8272-brg", + "fsl,cpm2-brg", + "fsl,cpm-brg"; + reg = <119f0 10 115f0 10>; + clock-frequency = <d#25000000>; + }; + + vi) Interrupt Controllers + + Currently defined compatibles: + - fsl,cpm1-pic + - only one interrupt cell + - fsl,pq1-pic + - fsl,cpm2-pic + - second interrupt cell is level/sense: + - 2 is falling edge + - 8 is active low + + Example: + + interrupt-controller@10c00 { + #interrupt-cells = <2>; + interrupt-controller; + reg = <10c00 80>; + compatible = "mpc8272-pic", "fsl,cpm2-pic"; + }; + + vii) USB (Universal Serial Bus Controller) + + Properties: + - compatible : "fsl,cpm1-usb", "fsl,cpm2-usb", "fsl,qe-usb" + + Example: + usb@11bc0 { + #address-cells = <1>; + #size-cells = <0>; + compatible = "fsl,cpm2-usb"; + reg = <11b60 18 8b00 100>; + interrupts = <b 8>; + interrupt-parent = <&PIC>; + fsl,cpm-command = <2e600000>; + }; + More devices will be defined as this spec matures. VII - Specifying interrupt information for devices diff --git a/arch/powerpc/platforms/Kconfig b/arch/powerpc/platforms/Kconfig index 92fcd6e35b5..8a62ca533b3 100644 --- a/arch/powerpc/platforms/Kconfig +++ b/arch/powerpc/platforms/Kconfig @@ -279,6 +279,17 @@ config CPM2 you wish to build a kernel for a machine with a CPM2 coprocessor on it (826x, 827x, 8560). +config PPC_CPM_NEW_BINDING + bool + depends on CPM1 || CPM2 + help + Select this if your board has been converted to use the new + device tree bindings for CPM, and no longer needs the + ioport callbacks or the platform device glue code. + + The fs_enet and cpm_uart drivers will be built as + of_platform devices. + config AXON_RAM tristate "Axon DDR2 memory device driver" depends on PPC_IBM_CELL_BLADE diff --git a/arch/powerpc/sysdev/fsl_soc.c b/arch/powerpc/sysdev/fsl_soc.c index 30523667df4..b465b30c954 100644 --- a/arch/powerpc/sysdev/fsl_soc.c +++ b/arch/powerpc/sysdev/fsl_soc.c @@ -665,6 +665,7 @@ err: arch_initcall(fsl_usb_of_init); +#ifndef CONFIG_PPC_CPM_NEW_BINDING #ifdef CONFIG_CPM2 extern void init_scc_ioports(struct fs_uart_platform_info*); @@ -1204,6 +1205,7 @@ err: arch_initcall(cpm_smc_uart_of_init); #endif /* CONFIG_8xx */ +#endif /* CONFIG_PPC_CPM_NEW_BINDING */ int __init fsl_spi_init(struct spi_board_info *board_infos, unsigned int num_board_infos, |