diff options
Diffstat (limited to 'include/asm-m68k/mac_via.h')
| -rw-r--r-- | include/asm-m68k/mac_via.h | 268 |
1 files changed, 268 insertions, 0 deletions
diff --git a/include/asm-m68k/mac_via.h b/include/asm-m68k/mac_via.h new file mode 100644 index 000000000000..59b758cd16ad --- /dev/null +++ b/include/asm-m68k/mac_via.h @@ -0,0 +1,268 @@ +/* + * 6522 Versatile Interface Adapter (VIA) + * + * There are two of these on the Mac II. Some IRQ's are vectored + * via them as are assorted bits and bobs - eg rtc, adb. The picture + * is a bit incomplete as the Mac documentation doesn't cover this well + */ + +#ifndef _ASM_MAC_VIA_H_ +#define _ASM_MAC_VIA_H_ + +/* + * Base addresses for the VIAs. There are two in every machine, + * although on some machines the second is an RBV or an OSS. + * The OSS is different enough that it's handled separately. + * + * Do not use these values directly; use the via1 and via2 variables + * instead (and don't forget to check rbv_present when using via2!) + */ + +#define VIA1_BASE (0x50F00000) +#define VIA2_BASE (0x50F02000) +#define RBV_BASE (0x50F26000) + +/* + * Not all of these are true post MacII I think. + * CSA: probably the ones CHRP marks as 'unused' change purposes + * when the IWM becomes the SWIM. + * http://www.rs6000.ibm.com/resource/technology/chrpio/via5.mak.html + * ftp://ftp.austin.ibm.com/pub/technology/spec/chrp/inwork/CHRP_IORef_1.0.pdf + * + * also, http://developer.apple.com/technotes/hw/hw_09.html claims the + * following changes for IIfx: + * VIA1A_vSccWrReq not available and that VIA1A_vSync has moved to an IOP. + * Also, "All of the functionality of VIA2 has been moved to other chips". + */ + +#define VIA1A_vSccWrReq 0x80 /* SCC write. (input) + * [CHRP] SCC WREQ: Reflects the state of the + * Wait/Request pins from the SCC. + * [Macintosh Family Hardware] + * as CHRP on SE/30,II,IIx,IIcx,IIci. + * on IIfx, "0 means an active request" + */ +#define VIA1A_vRev8 0x40 /* Revision 8 board ??? + * [CHRP] En WaitReqB: Lets the WaitReq_L + * signal from port B of the SCC appear on + * the PA7 input pin. Output. + * [Macintosh Family] On the SE/30, this + * is the bit to flip screen buffers. + * 0=alternate, 1=main. + * on II,IIx,IIcx,IIci,IIfx this is a bit + * for Rev ID. 0=II,IIx, 1=IIcx,IIci,IIfx + */ +#define VIA1A_vHeadSel 0x20 /* Head select for IWM. + * [CHRP] unused. + * [Macintosh Family] "Floppy disk + * state-control line SEL" on all but IIfx + */ +#define VIA1A_vOverlay 0x10 /* [Macintosh Family] On SE/30,II,IIx,IIcx + * this bit enables the "Overlay" address + * map in the address decoders as it is on + * reset for mapping the ROM over the reset + * vector. 1=use overlay map. + * On the IIci,IIfx it is another bit of the + * CPU ID: 0=normal IIci, 1=IIci with parity + * feature or IIfx. + * [CHRP] En WaitReqA: Lets the WaitReq_L + * signal from port A of the SCC appear + * on the PA7 input pin (CHRP). Output. + * [MkLinux] "Drive Select" + * (with 0x20 being 'disk head select') + */ +#define VIA1A_vSync 0x08 /* [CHRP] Sync Modem: modem clock select: + * 1: select the external serial clock to + * drive the SCC's /RTxCA pin. + * 0: Select the 3.6864MHz clock to drive + * the SCC cell. + * [Macintosh Family] Correct on all but IIfx + */ + +/* Macintosh Family Hardware sez: bits 0-2 of VIA1A are volume control + * on Macs which had the PWM sound hardware. Reserved on newer models. + * On IIci,IIfx, bits 1-2 are the rest of the CPU ID: + * bit 2: 1=IIci, 0=IIfx + * bit 1: 1 on both IIci and IIfx. + * MkLinux sez bit 0 is 'burnin flag' in this case. + * CHRP sez: VIA1A bits 0-2 and 5 are 'unused': if programmed as + * inputs, these bits will read 0. + */ +#define VIA1A_vVolume 0x07 /* Audio volume mask for PWM */ +#define VIA1A_CPUID0 0x02 /* CPU id bit 0 on RBV, others */ +#define VIA1A_CPUID1 0x04 /* CPU id bit 0 on RBV, others */ +#define VIA1A_CPUID2 0x10 /* CPU id bit 0 on RBV, others */ +#define VIA1A_CPUID3 0x40 /* CPU id bit 0 on RBV, others */ + +/* Info on VIA1B is from Macintosh Family Hardware & MkLinux. + * CHRP offers no info. */ +#define VIA1B_vSound 0x80 /* Sound enable (for compatibility with + * PWM hardware) 0=enabled. + * Also, on IIci w/parity, shows parity error + * 0=error, 1=OK. */ +#define VIA1B_vMystery 0x40 /* On IIci, parity enable. 0=enabled,1=disabled + * On SE/30, vertical sync interrupt enable. + * 0=enabled. This vSync interrupt shows up + * as a slot $E interrupt. */ +#define VIA1B_vADBS2 0x20 /* ADB state input bit 1 (unused on IIfx) */ +#define VIA1B_vADBS1 0x10 /* ADB state input bit 0 (unused on IIfx) */ +#define VIA1B_vADBInt 0x08 /* ADB interrupt 0=interrupt (unused on IIfx)*/ +#define VIA1B_vRTCEnb 0x04 /* Enable Real time clock. 0=enabled. */ +#define VIA1B_vRTCClk 0x02 /* Real time clock serial-clock line. */ +#define VIA1B_vRTCData 0x01 /* Real time clock serial-data line. */ + +/* MkLinux defines the following "VIA1 Register B contents where they + * differ from standard VIA1". From the naming scheme, we assume they + * correspond to a VIA work-alike named 'EVR'. */ +#define EVRB_XCVR 0x08 /* XCVR_SESSION* */ +#define EVRB_FULL 0x10 /* VIA_FULL */ +#define EVRB_SYSES 0x20 /* SYS_SESSION */ +#define EVRB_AUXIE 0x00 /* Enable A/UX Interrupt Scheme */ +#define EVRB_AUXID 0x40 /* Disable A/UX Interrupt Scheme */ +#define EVRB_SFTWRIE 0x00 /* Software Interrupt ReQuest */ +#define EVRB_SFTWRID 0x80 /* Software Interrupt ReQuest */ + +/* + * VIA2 A register is the interrupt lines raised off the nubus + * slots. + * The below info is from 'Macintosh Family Hardware.' + * MkLinux calls the 'IIci internal video IRQ' below the 'RBV slot 0 irq.' + * It also notes that the slot $9 IRQ is the 'Ethernet IRQ' and + * defines the 'Video IRQ' as 0x40 for the 'EVR' VIA work-alike. + * Perhaps OSS uses vRAM1 and vRAM2 for ADB. + */ + +#define VIA2A_vRAM1 0x80 /* RAM size bit 1 (IIci: reserved) */ +#define VIA2A_vRAM0 0x40 /* RAM size bit 0 (IIci: internal video IRQ) */ +#define VIA2A_vIRQE 0x20 /* IRQ from slot $E */ +#define VIA2A_vIRQD 0x10 /* IRQ from slot $D */ +#define VIA2A_vIRQC 0x08 /* IRQ from slot $C */ +#define VIA2A_vIRQB 0x04 /* IRQ from slot $B */ +#define VIA2A_vIRQA 0x02 /* IRQ from slot $A */ +#define VIA2A_vIRQ9 0x01 /* IRQ from slot $9 */ + +/* RAM size bits decoded as follows: + * bit1 bit0 size of ICs in bank A + * 0 0 256 kbit + * 0 1 1 Mbit + * 1 0 4 Mbit + * 1 1 16 Mbit + */ + +/* + * Register B has the fun stuff in it + */ + +#define VIA2B_vVBL 0x80 /* VBL output to VIA1 (60.15Hz) driven by + * timer T1. + * on IIci, parity test: 0=test mode. + * [MkLinux] RBV_PARODD: 1=odd,0=even. */ +#define VIA2B_vSndJck 0x40 /* External sound jack status. + * 0=plug is inserted. On SE/30, always 0 */ +#define VIA2B_vTfr0 0x20 /* Transfer mode bit 0 ack from NuBus */ +#define VIA2B_vTfr1 0x10 /* Transfer mode bit 1 ack from NuBus */ +#define VIA2B_vMode32 0x08 /* 24/32bit switch - doubles as cache flush + * on II, AMU/PMMU control. + * if AMU, 0=24bit to 32bit translation + * if PMMU, 1=PMMU is accessing page table. + * on SE/30 tied low. + * on IIx,IIcx,IIfx, unused. + * on IIci/RBV, cache control. 0=flush cache. + */ +#define VIA2B_vPower 0x04 /* Power off, 0=shut off power. + * on SE/30 this signal sent to PDS card. */ +#define VIA2B_vBusLk 0x02 /* Lock NuBus transactions, 0=locked. + * on SE/30 sent to PDS card. */ +#define VIA2B_vCDis 0x01 /* Cache control. On IIci, 1=disable cache card + * on others, 0=disable processor's instruction + * and data caches. */ + +/* Apple sez: http://developer.apple.com/technotes/ov/ov_04.html + * Another example of a valid function that has no ROM support is the use + * of the alternate video page for page-flipping animation. Since there + * is no ROM call to flip pages, it is necessary to go play with the + * right bit in the VIA chip (6522 Versatile Interface Adapter). + * [CSA: don't know which one this is, but it's one of 'em!] + */ + +/* + * 6522 registers - see databook. + * CSA: Assignments for VIA1 confirmed from CHRP spec. + */ + +/* partial address decode. 0xYYXX : XX part for RBV, YY part for VIA */ +/* Note: 15 VIA regs, 8 RBV regs */ + +#define vBufB 0x0000 /* [VIA/RBV] Register B */ +#define vBufAH 0x0200 /* [VIA only] Buffer A, with handshake. DON'T USE! */ +#define vDirB 0x0400 /* [VIA only] Data Direction Register B. */ +#define vDirA 0x0600 /* [VIA only] Data Direction Register A. */ +#define vT1CL 0x0800 /* [VIA only] Timer one counter low. */ +#define vT1CH 0x0a00 /* [VIA only] Timer one counter high. */ +#define vT1LL 0x0c00 /* [VIA only] Timer one latches low. */ +#define vT1LH 0x0e00 /* [VIA only] Timer one latches high. */ +#define vT2CL 0x1000 /* [VIA only] Timer two counter low. */ +#define vT2CH 0x1200 /* [VIA only] Timer two counter high. */ +#define vSR 0x1400 /* [VIA only] Shift register. */ +#define vACR 0x1600 /* [VIA only] Auxilary control register. */ +#define vPCR 0x1800 /* [VIA only] Peripheral control register. */ + /* CHRP sez never ever to *write* this. + * Mac family says never to *change* this. + * In fact we need to initialize it once at start. */ +#define vIFR 0x1a00 /* [VIA/RBV] Interrupt flag register. */ +#define vIER 0x1c00 /* [VIA/RBV] Interrupt enable register. */ +#define vBufA 0x1e00 /* [VIA/RBV] register A (no handshake) */ + +/* The RBV only decodes the bottom eight address lines; the VIA doesn't + * decode the bottom eight -- so vBufB | rBufB will always get you BufB */ +/* CSA: in fact, only bits 0,1, and 4 seem to be decoded. + * BUT note the values for rIER and rIFR, where the top 8 bits *do* seem + * to matter. In fact *all* of the top 8 bits seem to matter; + * setting rIER=0x1813 and rIFR=0x1803 doesn't work, either. + * Perhaps some sort of 'compatibility mode' is built-in? [21-May-1999] + */ + +#define rBufB 0x0000 /* [VIA/RBV] Register B */ +#define rExp 0x0001 /* [RBV only] RBV future expansion (always 0) */ +#define rSIFR 0x0002 /* [RBV only] RBV slot interrupts register. */ +#define rIFR 0x1a03 /* [VIA/RBV] RBV interrupt flag register. */ +#define rMonP 0x0010 /* [RBV only] RBV video monitor type. */ +#define rChpT 0x0011 /* [RBV only] RBV test mode register (reads as 0). */ +#define rSIER 0x0012 /* [RBV only] RBV slot interrupt enables. */ +#define rIER 0x1c13 /* [VIA/RBV] RBV interrupt flag enable register. */ +#define rBufA rSIFR /* the 'slot interrupts register' is BufA on a VIA */ + +/* + * Video monitor parameters, for rMonP: + */ +#define RBV_DEPTH 0x07 /* bits per pixel: 000=1,001=2,010=4,011=8 */ +#define RBV_MONID 0x38 /* monitor type, as below. */ +#define RBV_VIDOFF 0x40 /* 1 turns off onboard video */ +/* Supported monitor types: */ +#define MON_15BW (1<<3) /* 15" BW portrait. */ +#define MON_IIGS (2<<3) /* 12" color (modified IIGS monitor). */ +#define MON_15RGB (5<<3) /* 15" RGB portrait. */ +#define MON_12OR13 (6<<3) /* 12" BW or 13" RGB. */ +#define MON_NONE (7<<3) /* No monitor attached. */ + +/* To clarify IER manipulations */ +#define IER_SET_BIT(b) (0x80 | (1<<(b)) ) +#define IER_CLR_BIT(b) (0x7F & (1<<(b)) ) + +#ifndef __ASSEMBLY__ + +extern volatile __u8 *via1,*via2; +extern int rbv_present,via_alt_mapping; +extern __u8 rbv_clear; + +static inline int rbv_set_video_bpp(int bpp) +{ + char val = (bpp==1)?0:(bpp==2)?1:(bpp==4)?2:(bpp==8)?3:-1; + if (!rbv_present || val<0) return -1; + via2[rMonP] = (via2[rMonP] & ~RBV_DEPTH) | val; + return 0; +} + +#endif /* __ASSEMBLY__ */ + +#endif /* _ASM_MAC_VIA_H_ */ |