diff options
Diffstat (limited to 'drivers/net/ethernet/intel/igb/e1000_82575.c')
| -rw-r--r-- | drivers/net/ethernet/intel/igb/e1000_82575.c | 2101 |
1 files changed, 2101 insertions, 0 deletions
diff --git a/drivers/net/ethernet/intel/igb/e1000_82575.c b/drivers/net/ethernet/intel/igb/e1000_82575.c new file mode 100644 index 000000000000..7881fb95a25b --- /dev/null +++ b/drivers/net/ethernet/intel/igb/e1000_82575.c @@ -0,0 +1,2101 @@ +/******************************************************************************* + + Intel(R) Gigabit Ethernet Linux driver + Copyright(c) 2007-2011 Intel Corporation. + + This program is free software; you can redistribute it and/or modify it + under the terms and conditions of the GNU General Public License, + version 2, as published by the Free Software Foundation. + + This program is distributed in the hope it will be useful, but WITHOUT + ANY WARRANTY; without even the implied warranty of MERCHANTABILITY or + FITNESS FOR A PARTICULAR PURPOSE. See the GNU General Public License for + more details. + + You should have received a copy of the GNU General Public License along with + this program; if not, write to the Free Software Foundation, Inc., + 51 Franklin St - Fifth Floor, Boston, MA 02110-1301 USA. + + The full GNU General Public License is included in this distribution in + the file called "COPYING". + + Contact Information: + e1000-devel Mailing List <e1000-devel@lists.sourceforge.net> + Intel Corporation, 5200 N.E. Elam Young Parkway, Hillsboro, OR 97124-6497 + +*******************************************************************************/ + +/* e1000_82575 + * e1000_82576 + */ + +#include <linux/types.h> +#include <linux/if_ether.h> + +#include "e1000_mac.h" +#include "e1000_82575.h" + +static s32 igb_get_invariants_82575(struct e1000_hw *); +static s32 igb_acquire_phy_82575(struct e1000_hw *); +static void igb_release_phy_82575(struct e1000_hw *); +static s32 igb_acquire_nvm_82575(struct e1000_hw *); +static void igb_release_nvm_82575(struct e1000_hw *); +static s32 igb_check_for_link_82575(struct e1000_hw *); +static s32 igb_get_cfg_done_82575(struct e1000_hw *); +static s32 igb_init_hw_82575(struct e1000_hw *); +static s32 igb_phy_hw_reset_sgmii_82575(struct e1000_hw *); +static s32 igb_read_phy_reg_sgmii_82575(struct e1000_hw *, u32, u16 *); +static s32 igb_read_phy_reg_82580(struct e1000_hw *, u32, u16 *); +static s32 igb_write_phy_reg_82580(struct e1000_hw *, u32, u16); +static s32 igb_reset_hw_82575(struct e1000_hw *); +static s32 igb_reset_hw_82580(struct e1000_hw *); +static s32 igb_set_d0_lplu_state_82575(struct e1000_hw *, bool); +static s32 igb_setup_copper_link_82575(struct e1000_hw *); +static s32 igb_setup_serdes_link_82575(struct e1000_hw *); +static s32 igb_write_phy_reg_sgmii_82575(struct e1000_hw *, u32, u16); +static void igb_clear_hw_cntrs_82575(struct e1000_hw *); +static s32 igb_acquire_swfw_sync_82575(struct e1000_hw *, u16); +static s32 igb_get_pcs_speed_and_duplex_82575(struct e1000_hw *, u16 *, + u16 *); +static s32 igb_get_phy_id_82575(struct e1000_hw *); +static void igb_release_swfw_sync_82575(struct e1000_hw *, u16); +static bool igb_sgmii_active_82575(struct e1000_hw *); +static s32 igb_reset_init_script_82575(struct e1000_hw *); +static s32 igb_read_mac_addr_82575(struct e1000_hw *); +static s32 igb_set_pcie_completion_timeout(struct e1000_hw *hw); +static s32 igb_reset_mdicnfg_82580(struct e1000_hw *hw); +static s32 igb_validate_nvm_checksum_82580(struct e1000_hw *hw); +static s32 igb_update_nvm_checksum_82580(struct e1000_hw *hw); +static s32 igb_validate_nvm_checksum_i350(struct e1000_hw *hw); +static s32 igb_update_nvm_checksum_i350(struct e1000_hw *hw); +static const u16 e1000_82580_rxpbs_table[] = + { 36, 72, 144, 1, 2, 4, 8, 16, + 35, 70, 140 }; +#define E1000_82580_RXPBS_TABLE_SIZE \ + (sizeof(e1000_82580_rxpbs_table)/sizeof(u16)) + +/** + * igb_sgmii_uses_mdio_82575 - Determine if I2C pins are for external MDIO + * @hw: pointer to the HW structure + * + * Called to determine if the I2C pins are being used for I2C or as an + * external MDIO interface since the two options are mutually exclusive. + **/ +static bool igb_sgmii_uses_mdio_82575(struct e1000_hw *hw) +{ + u32 reg = 0; + bool ext_mdio = false; + + switch (hw->mac.type) { + case e1000_82575: + case e1000_82576: + reg = rd32(E1000_MDIC); + ext_mdio = !!(reg & E1000_MDIC_DEST); + break; + case e1000_82580: + case e1000_i350: + reg = rd32(E1000_MDICNFG); + ext_mdio = !!(reg & E1000_MDICNFG_EXT_MDIO); + break; + default: + break; + } + return ext_mdio; +} + +static s32 igb_get_invariants_82575(struct e1000_hw *hw) +{ + struct e1000_phy_info *phy = &hw->phy; + struct e1000_nvm_info *nvm = &hw->nvm; + struct e1000_mac_info *mac = &hw->mac; + struct e1000_dev_spec_82575 * dev_spec = &hw->dev_spec._82575; + u32 eecd; + s32 ret_val; + u16 size; + u32 ctrl_ext = 0; + + switch (hw->device_id) { + case E1000_DEV_ID_82575EB_COPPER: + case E1000_DEV_ID_82575EB_FIBER_SERDES: + case E1000_DEV_ID_82575GB_QUAD_COPPER: + mac->type = e1000_82575; + break; + case E1000_DEV_ID_82576: + case E1000_DEV_ID_82576_NS: + case E1000_DEV_ID_82576_NS_SERDES: + case E1000_DEV_ID_82576_FIBER: + case E1000_DEV_ID_82576_SERDES: + case E1000_DEV_ID_82576_QUAD_COPPER: + case E1000_DEV_ID_82576_QUAD_COPPER_ET2: + case E1000_DEV_ID_82576_SERDES_QUAD: + mac->type = e1000_82576; + break; + case E1000_DEV_ID_82580_COPPER: + case E1000_DEV_ID_82580_FIBER: + case E1000_DEV_ID_82580_QUAD_FIBER: + case E1000_DEV_ID_82580_SERDES: + case E1000_DEV_ID_82580_SGMII: + case E1000_DEV_ID_82580_COPPER_DUAL: + case E1000_DEV_ID_DH89XXCC_SGMII: + case E1000_DEV_ID_DH89XXCC_SERDES: + case E1000_DEV_ID_DH89XXCC_BACKPLANE: + case E1000_DEV_ID_DH89XXCC_SFP: + mac->type = e1000_82580; + break; + case E1000_DEV_ID_I350_COPPER: + case E1000_DEV_ID_I350_FIBER: + case E1000_DEV_ID_I350_SERDES: + case E1000_DEV_ID_I350_SGMII: + mac->type = e1000_i350; + break; + default: + return -E1000_ERR_MAC_INIT; + break; + } + + /* Set media type */ + /* + * The 82575 uses bits 22:23 for link mode. The mode can be changed + * based on the EEPROM. We cannot rely upon device ID. There + * is no distinguishable difference between fiber and internal + * SerDes mode on the 82575. There can be an external PHY attached + * on the SGMII interface. For this, we'll set sgmii_active to true. + */ + phy->media_type = e1000_media_type_copper; + dev_spec->sgmii_active = false; + + ctrl_ext = rd32(E1000_CTRL_EXT); + switch (ctrl_ext & E1000_CTRL_EXT_LINK_MODE_MASK) { + case E1000_CTRL_EXT_LINK_MODE_SGMII: + dev_spec->sgmii_active = true; + break; + case E1000_CTRL_EXT_LINK_MODE_1000BASE_KX: + case E1000_CTRL_EXT_LINK_MODE_PCIE_SERDES: + hw->phy.media_type = e1000_media_type_internal_serdes; + break; + default: + break; + } + + /* Set mta register count */ + mac->mta_reg_count = 128; + /* Set rar entry count */ + mac->rar_entry_count = E1000_RAR_ENTRIES_82575; + if (mac->type == e1000_82576) + mac->rar_entry_count = E1000_RAR_ENTRIES_82576; + if (mac->type == e1000_82580) + mac->rar_entry_count = E1000_RAR_ENTRIES_82580; + if (mac->type == e1000_i350) + mac->rar_entry_count = E1000_RAR_ENTRIES_I350; + /* reset */ + if (mac->type >= e1000_82580) + mac->ops.reset_hw = igb_reset_hw_82580; + else + mac->ops.reset_hw = igb_reset_hw_82575; + /* Set if part includes ASF firmware */ + mac->asf_firmware_present = true; + /* Set if manageability features are enabled. */ + mac->arc_subsystem_valid = + (rd32(E1000_FWSM) & E1000_FWSM_MODE_MASK) + ? true : false; + /* enable EEE on i350 parts */ + if (mac->type == e1000_i350) + dev_spec->eee_disable = false; + else + dev_spec->eee_disable = true; + /* physical interface link setup */ + mac->ops.setup_physical_interface = + (hw->phy.media_type == e1000_media_type_copper) + ? igb_setup_copper_link_82575 + : igb_setup_serdes_link_82575; + + /* NVM initialization */ + eecd = rd32(E1000_EECD); + + nvm->opcode_bits = 8; + nvm->delay_usec = 1; + switch (nvm->override) { + case e1000_nvm_override_spi_large: + nvm->page_size = 32; + nvm->address_bits = 16; + break; + case e1000_nvm_override_spi_small: + nvm->page_size = 8; + nvm->address_bits = 8; + break; + default: + nvm->page_size = eecd & E1000_EECD_ADDR_BITS ? 32 : 8; + nvm->address_bits = eecd & E1000_EECD_ADDR_BITS ? 16 : 8; + break; + } + + nvm->type = e1000_nvm_eeprom_spi; + + size = (u16)((eecd & E1000_EECD_SIZE_EX_MASK) >> + E1000_EECD_SIZE_EX_SHIFT); + + /* + * Added to a constant, "size" becomes the left-shift value + * for setting word_size. + */ + size += NVM_WORD_SIZE_BASE_SHIFT; + + /* + * Check for invalid size + */ + if ((hw->mac.type == e1000_82576) && (size > 15)) { + printk("igb: The NVM size is not valid, " + "defaulting to 32K.\n"); + size = 15; + } + nvm->word_size = 1 << size; + if (nvm->word_size == (1 << 15)) + nvm->page_size = 128; + + /* NVM Function Pointers */ + nvm->ops.acquire = igb_acquire_nvm_82575; + if (nvm->word_size < (1 << 15)) + nvm->ops.read = igb_read_nvm_eerd; + else + nvm->ops.read = igb_read_nvm_spi; + + nvm->ops.release = igb_release_nvm_82575; + switch (hw->mac.type) { + case e1000_82580: + nvm->ops.validate = igb_validate_nvm_checksum_82580; + nvm->ops.update = igb_update_nvm_checksum_82580; + break; + case e1000_i350: + nvm->ops.validate = igb_validate_nvm_checksum_i350; + nvm->ops.update = igb_update_nvm_checksum_i350; + break; + default: + nvm->ops.validate = igb_validate_nvm_checksum; + nvm->ops.update = igb_update_nvm_checksum; + } + nvm->ops.write = igb_write_nvm_spi; + + /* if part supports SR-IOV then initialize mailbox parameters */ + switch (mac->type) { + case e1000_82576: + case e1000_i350: + igb_init_mbx_params_pf(hw); + break; + default: + break; + } + + /* setup PHY parameters */ + if (phy->media_type != e1000_media_type_copper) { + phy->type = e1000_phy_none; + return 0; + } + + phy->autoneg_mask = AUTONEG_ADVERTISE_SPEED_DEFAULT; + phy->reset_delay_us = 100; + + ctrl_ext = rd32(E1000_CTRL_EXT); + + /* PHY function pointers */ + if (igb_sgmii_active_82575(hw)) { + phy->ops.reset = igb_phy_hw_reset_sgmii_82575; + ctrl_ext |= E1000_CTRL_I2C_ENA; + } else { + phy->ops.reset = igb_phy_hw_reset; + ctrl_ext &= ~E1000_CTRL_I2C_ENA; + } + + wr32(E1000_CTRL_EXT, ctrl_ext); + igb_reset_mdicnfg_82580(hw); + + if (igb_sgmii_active_82575(hw) && !igb_sgmii_uses_mdio_82575(hw)) { + phy->ops.read_reg = igb_read_phy_reg_sgmii_82575; + phy->ops.write_reg = igb_write_phy_reg_sgmii_82575; + } else if (hw->mac.type >= e1000_82580) { + phy->ops.read_reg = igb_read_phy_reg_82580; + phy->ops.write_reg = igb_write_phy_reg_82580; + } else { + phy->ops.read_reg = igb_read_phy_reg_igp; + phy->ops.write_reg = igb_write_phy_reg_igp; + } + + /* set lan id */ + hw->bus.func = (rd32(E1000_STATUS) & E1000_STATUS_FUNC_MASK) >> + E1000_STATUS_FUNC_SHIFT; + + /* Set phy->phy_addr and phy->id. */ + ret_val = igb_get_phy_id_82575(hw); + if (ret_val) + return ret_val; + + /* Verify phy id and set remaining function pointers */ + switch (phy->id) { + case I347AT4_E_PHY_ID: + case M88E1112_E_PHY_ID: + case M88E1111_I_PHY_ID: + phy->type = e1000_phy_m88; + phy->ops.get_phy_info = igb_get_phy_info_m88; + + if (phy->id == I347AT4_E_PHY_ID || + phy->id == M88E1112_E_PHY_ID) + phy->ops.get_cable_length = igb_get_cable_length_m88_gen2; + else + phy->ops.get_cable_length = igb_get_cable_length_m88; + + phy->ops.force_speed_duplex = igb_phy_force_speed_duplex_m88; + break; + case IGP03E1000_E_PHY_ID: + phy->type = e1000_phy_igp_3; + phy->ops.get_phy_info = igb_get_phy_info_igp; + phy->ops.get_cable_length = igb_get_cable_length_igp_2; + phy->ops.force_speed_duplex = igb_phy_force_speed_duplex_igp; + phy->ops.set_d0_lplu_state = igb_set_d0_lplu_state_82575; + phy->ops.set_d3_lplu_state = igb_set_d3_lplu_state; + break; + case I82580_I_PHY_ID: + case I350_I_PHY_ID: + phy->type = e1000_phy_82580; + phy->ops.force_speed_duplex = igb_phy_force_speed_duplex_82580; + phy->ops.get_cable_length = igb_get_cable_length_82580; + phy->ops.get_phy_info = igb_get_phy_info_82580; + break; + default: + return -E1000_ERR_PHY; + } + + return 0; +} + +/** + * igb_acquire_phy_82575 - Acquire rights to access PHY + * @hw: pointer to the HW structure + * + * Acquire access rights to the correct PHY. This is a + * function pointer entry point called by the api module. + **/ +static s32 igb_acquire_phy_82575(struct e1000_hw *hw) +{ + u16 mask = E1000_SWFW_PHY0_SM; + + if (hw->bus.func == E1000_FUNC_1) + mask = E1000_SWFW_PHY1_SM; + else if (hw->bus.func == E1000_FUNC_2) + mask = E1000_SWFW_PHY2_SM; + else if (hw->bus.func == E1000_FUNC_3) + mask = E1000_SWFW_PHY3_SM; + + return igb_acquire_swfw_sync_82575(hw, mask); +} + +/** + * igb_release_phy_82575 - Release rights to access PHY + * @hw: pointer to the HW structure + * + * A wrapper to release access rights to the correct PHY. This is a + * function pointer entry point called by the api module. + **/ +static void igb_release_phy_82575(struct e1000_hw *hw) +{ + u16 mask = E1000_SWFW_PHY0_SM; + + if (hw->bus.func == E1000_FUNC_1) + mask = E1000_SWFW_PHY1_SM; + else if (hw->bus.func == E1000_FUNC_2) + mask = E1000_SWFW_PHY2_SM; + else if (hw->bus.func == E1000_FUNC_3) + mask = E1000_SWFW_PHY3_SM; + + igb_release_swfw_sync_82575(hw, mask); +} + +/** + * igb_read_phy_reg_sgmii_82575 - Read PHY register using sgmii + * @hw: pointer to the HW structure + * @offset: register offset to be read + * @data: pointer to the read data + * + * Reads the PHY register at offset using the serial gigabit media independent + * interface and stores the retrieved information in data. + **/ +static s32 igb_read_phy_reg_sgmii_82575(struct e1000_hw *hw, u32 offset, + u16 *data) +{ + s32 ret_val = -E1000_ERR_PARAM; + + if (offset > E1000_MAX_SGMII_PHY_REG_ADDR) { + hw_dbg("PHY Address %u is out of range\n", offset); + goto out; + } + + ret_val = hw->phy.ops.acquire(hw); + if (ret_val) + goto out; + + ret_val = igb_read_phy_reg_i2c(hw, offset, data); + + hw->phy.ops.release(hw); + +out: + return ret_val; +} + +/** + * igb_write_phy_reg_sgmii_82575 - Write PHY register using sgmii + * @hw: pointer to the HW structure + * @offset: register offset to write to + * @data: data to write at register offset + * + * Writes the data to PHY register at the offset using the serial gigabit + * media independent interface. + **/ +static s32 igb_write_phy_reg_sgmii_82575(struct e1000_hw *hw, u32 offset, + u16 data) +{ + s32 ret_val = -E1000_ERR_PARAM; + + + if (offset > E1000_MAX_SGMII_PHY_REG_ADDR) { + hw_dbg("PHY Address %d is out of range\n", offset); + goto out; + } + + ret_val = hw->phy.ops.acquire(hw); + if (ret_val) + goto out; + + ret_val = igb_write_phy_reg_i2c(hw, offset, data); + + hw->phy.ops.release(hw); + +out: + return ret_val; +} + +/** + * igb_get_phy_id_82575 - Retrieve PHY addr and id + * @hw: pointer to the HW structure + * + * Retrieves the PHY address and ID for both PHY's which do and do not use + * sgmi interface. + **/ +static s32 igb_get_phy_id_82575(struct e1000_hw *hw) +{ + struct e1000_phy_info *phy = &hw->phy; + s32 ret_val = 0; + u16 phy_id; + u32 ctrl_ext; + u32 mdic; + + /* + * For SGMII PHYs, we try the list of possible addresses until + * we find one that works. For non-SGMII PHYs + * (e.g. integrated copper PHYs), an address of 1 should + * work. The result of this function should mean phy->phy_addr + * and phy->id are set correctly. + */ + if (!(igb_sgmii_active_82575(hw))) { + phy->addr = 1; + ret_val = igb_get_phy_id(hw); + goto out; + } + + if (igb_sgmii_uses_mdio_82575(hw)) { + switch (hw->mac.type) { + case e1000_82575: + case e1000_82576: + mdic = rd32(E1000_MDIC); + mdic &= E1000_MDIC_PHY_MASK; + phy->addr = mdic >> E1000_MDIC_PHY_SHIFT; + break; + case e1000_82580: + case e1000_i350: + mdic = rd32(E1000_MDICNFG); + mdic &= E1000_MDICNFG_PHY_MASK; + phy->addr = mdic >> E1000_MDICNFG_PHY_SHIFT; + break; + default: + ret_val = -E1000_ERR_PHY; + goto out; + break; + } + ret_val = igb_get_phy_id(hw); + goto out; + } + + /* Power on sgmii phy if it is disabled */ + ctrl_ext = rd32(E1000_CTRL_EXT); + wr32(E1000_CTRL_EXT, ctrl_ext & ~E1000_CTRL_EXT_SDP3_DATA); + wrfl(); + msleep(300); + + /* + * The address field in the I2CCMD register is 3 bits and 0 is invalid. + * Therefore, we need to test 1-7 + */ + for (phy->addr = 1; phy->addr < 8; phy->addr++) { + ret_val = igb_read_phy_reg_sgmii_82575(hw, PHY_ID1, &phy_id); + if (ret_val == 0) { + hw_dbg("Vendor ID 0x%08X read at address %u\n", + phy_id, phy->addr); + /* + * At the time of this writing, The M88 part is + * the only supported SGMII PHY product. + */ + if (phy_id == M88_VENDOR) + break; + } else { + hw_dbg("PHY address %u was unreadable\n", phy->addr); + } + } + + /* A valid PHY type couldn't be found. */ + if (phy->addr == 8) { + phy->addr = 0; + ret_val = -E1000_ERR_PHY; + goto out; + } else { + ret_val = igb_get_phy_id(hw); + } + + /* restore previous sfp cage power state */ + wr32(E1000_CTRL_EXT, ctrl_ext); + +out: + return ret_val; +} + +/** + * igb_phy_hw_reset_sgmii_82575 - Performs a PHY reset + * @hw: pointer to the HW structure + * + * Resets the PHY using the serial gigabit media independent interface. + **/ +static s32 igb_phy_hw_reset_sgmii_82575(struct e1000_hw *hw) +{ + s32 ret_val; + + /* + * This isn't a true "hard" reset, but is the only reset + * available to us at this time. + */ + + hw_dbg("Soft resetting SGMII attached PHY...\n"); + + /* + * SFP documentation requires the following to configure the SPF module + * to work on SGMII. No further documentation is given. + */ + ret_val = hw->phy.ops.write_reg(hw, 0x1B, 0x8084); + if (ret_val) + goto out; + + ret_val = igb_phy_sw_reset(hw); + +out: + return ret_val; +} + +/** + * igb_set_d0_lplu_state_82575 - Set Low Power Linkup D0 state + * @hw: pointer to the HW structure + * @active: true to enable LPLU, false to disable + * + * Sets the LPLU D0 state according to the active flag. When + * activating LPLU this function also disables smart speed + * and vice versa. LPLU will not be activated unless the + * device autonegotiation advertisement meets standards of + * either 10 or 10/100 or 10/100/1000 at all duplexes. + * This is a function pointer entry point only called by + * PHY setup routines. + **/ +static s32 igb_set_d0_lplu_state_82575(struct e1000_hw *hw, bool active) +{ + struct e1000_phy_info *phy = &hw->phy; + s32 ret_val; + u16 data; + + ret_val = phy->ops.read_reg(hw, IGP02E1000_PHY_POWER_MGMT, &data); + if (ret_val) + goto out; + + if (active) { + data |= IGP02E1000_PM_D0_LPLU; + ret_val = phy->ops.write_reg(hw, IGP02E1000_PHY_POWER_MGMT, + data); + if (ret_val) + goto out; + + /* When LPLU is enabled, we should disable SmartSpeed */ + ret_val = phy->ops.read_reg(hw, IGP01E1000_PHY_PORT_CONFIG, + &data); + data &= ~IGP01E1000_PSCFR_SMART_SPEED; + ret_val = phy->ops.write_reg(hw, IGP01E1000_PHY_PORT_CONFIG, + data); + if (ret_val) + goto out; + } else { + data &= ~IGP02E1000_PM_D0_LPLU; + ret_val = phy->ops.write_reg(hw, IGP02E1000_PHY_POWER_MGMT, + data); + /* + * LPLU and SmartSpeed are mutually exclusive. LPLU is used + * during Dx states where the power conservation is most + * important. During driver activity we should enable + * SmartSpeed, so performance is maintained. + */ + if (phy->smart_speed == e1000_smart_speed_on) { + ret_val = phy->ops.read_reg(hw, + IGP01E1000_PHY_PORT_CONFIG, &data); + if (ret_val) + goto out; + + data |= IGP01E1000_PSCFR_SMART_SPEED; + ret_val = phy->ops.write_reg(hw, + IGP01E1000_PHY_PORT_CONFIG, data); + if (ret_val) + goto out; + } else if (phy->smart_speed == e1000_smart_speed_off) { + ret_val = phy->ops.read_reg(hw, + IGP01E1000_PHY_PORT_CONFIG, &data); + if (ret_val) + goto out; + + data &= ~IGP01E1000_PSCFR_SMART_SPEED; + ret_val = phy->ops.write_reg(hw, + IGP01E1000_PHY_PORT_CONFIG, data); + if (ret_val) + goto out; + } + } + +out: + return ret_val; +} + +/** + * igb_acquire_nvm_82575 - Request for access to EEPROM + * @hw: pointer to the HW structure + * + * Acquire the necessary semaphores for exclusive access to the EEPROM. + * Set the EEPROM access request bit and wait for EEPROM access grant bit. + * Return successful if access grant bit set, else clear the request for + * EEPROM access and return -E1000_ERR_NVM (-1). + **/ +static s32 igb_acquire_nvm_82575(struct e1000_hw *hw) +{ + s32 ret_val; + + ret_val = igb_acquire_swfw_sync_82575(hw, E1000_SWFW_EEP_SM); + if (ret_val) + goto out; + + ret_val = igb_acquire_nvm(hw); + + if (ret_val) + igb_release_swfw_sync_82575(hw, E1000_SWFW_EEP_SM); + +out: + return ret_val; +} + +/** + * igb_release_nvm_82575 - Release exclusive access to EEPROM + * @hw: pointer to the HW structure + * + * Stop any current commands to the EEPROM and clear the EEPROM request bit, + * then release the semaphores acquired. + **/ +static void igb_release_nvm_82575(struct e1000_hw *hw) +{ + igb_release_nvm(hw); + igb_release_swfw_sync_82575(hw, E1000_SWFW_EEP_SM); +} + +/** + * igb_acquire_swfw_sync_82575 - Acquire SW/FW semaphore + * @hw: pointer to the HW structure + * @mask: specifies which semaphore to acquire + * + * Acquire the SW/FW semaphore to access the PHY or NVM. The mask + * will also specify which port we're acquiring the lock for. + **/ +static s32 igb_acquire_swfw_sync_82575(struct e1000_hw *hw, u16 mask) +{ + u32 swfw_sync; + u32 swmask = mask; + u32 fwmask = mask << 16; + s32 ret_val = 0; + s32 i = 0, timeout = 200; /* FIXME: find real value to use here */ + + while (i < timeout) { + if (igb_get_hw_semaphore(hw)) { + ret_val = -E1000_ERR_SWFW_SYNC; + goto out; + } + + swfw_sync = rd32(E1000_SW_FW_SYNC); + if (!(swfw_sync & (fwmask | swmask))) + break; + + /* + * Firmware currently using resource (fwmask) + * or other software thread using resource (swmask) + */ + igb_put_hw_semaphore(hw); + mdelay(5); + i++; + } + + if (i == timeout) { + hw_dbg("Driver can't access resource, SW_FW_SYNC timeout.\n"); + ret_val = -E1000_ERR_SWFW_SYNC; + goto out; + } + + swfw_sync |= swmask; + wr32(E1000_SW_FW_SYNC, swfw_sync); + + igb_put_hw_semaphore(hw); + +out: + return ret_val; +} + +/** + * igb_release_swfw_sync_82575 - Release SW/FW semaphore + * @hw: pointer to the HW structure + * @mask: specifies which semaphore to acquire + * + * Release the SW/FW semaphore used to access the PHY or NVM. The mask + * will also specify which port we're releasing the lock for. + **/ +static void igb_release_swfw_sync_82575(struct e1000_hw *hw, u16 mask) +{ + u32 swfw_sync; + + while (igb_get_hw_semaphore(hw) != 0); + /* Empty */ + + swfw_sync = rd32(E1000_SW_FW_SYNC); + swfw_sync &= ~mask; + wr32(E1000_SW_FW_SYNC, swfw_sync); + + igb_put_hw_semaphore(hw); +} + +/** + * igb_get_cfg_done_82575 - Read config done bit + * @hw: pointer to the HW structure + * + * Read the management control register for the config done bit for + * completion status. NOTE: silicon which is EEPROM-less will fail trying + * to read the config done bit, so an error is *ONLY* logged and returns + * 0. If we were to return with error, EEPROM-less silicon + * would not be able to be reset or change link. + **/ +static s32 igb_get_cfg_done_82575(struct e1000_hw *hw) +{ + s32 timeout = PHY_CFG_TIMEOUT; + s32 ret_val = 0; + u32 mask = E1000_NVM_CFG_DONE_PORT_0; + + if (hw->bus.func == 1) + mask = E1000_NVM_CFG_DONE_PORT_1; + else if (hw->bus.func == E1000_FUNC_2) + mask = E1000_NVM_CFG_DONE_PORT_2; + else if (hw->bus.func == E1000_FUNC_3) + mask = E1000_NVM_CFG_DONE_PORT_3; + + while (timeout) { + if (rd32(E1000_EEMNGCTL) & mask) + break; + msleep(1); + timeout--; + } + if (!timeout) + hw_dbg("MNG configuration cycle has not completed.\n"); + + /* If EEPROM is not marked present, init the PHY manually */ + if (((rd32(E1000_EECD) & E1000_EECD_PRES) == 0) && + (hw->phy.type == e1000_phy_igp_3)) + igb_phy_init_script_igp3(hw); + + return ret_val; +} + +/** + * igb_check_for_link_82575 - Check for link + * @hw: pointer to the HW structure + * + * If sgmii is enabled, then use the pcs register to determine link, otherwise + * use the generic interface for determining link. + **/ +static s32 igb_check_for_link_82575(struct e1000_hw *hw) +{ + s32 ret_val; + u16 speed, duplex; + + if (hw->phy.media_type != e1000_media_type_copper) { + ret_val = igb_get_pcs_speed_and_duplex_82575(hw, &speed, + &duplex); + /* + * Use this flag to determine if link needs to be checked or + * not. If we have link clear the flag so that we do not + * continue to check for link. + */ + hw->mac.get_link_status = !hw->mac.serdes_has_link; + } else { + ret_val = igb_check_for_copper_link(hw); + } + + return ret_val; +} + +/** + * igb_power_up_serdes_link_82575 - Power up the serdes link after shutdown + * @hw: pointer to the HW structure + **/ +void igb_power_up_serdes_link_82575(struct e1000_hw *hw) +{ + u32 reg; + + + if ((hw->phy.media_type != e1000_media_type_internal_serdes) && + !igb_sgmii_active_82575(hw)) + return; + + /* Enable PCS to turn on link */ + reg = rd32(E1000_PCS_CFG0); + reg |= E1000_PCS_CFG_PCS_EN; + wr32(E1000_PCS_CFG0, reg); + + /* Power up the laser */ + reg = rd32(E1000_CTRL_EXT); + reg &= ~E1000_CTRL_EXT_SDP3_DATA; + wr32(E1000_CTRL_EXT, reg); + + /* flush the write to verify completion */ + wrfl(); + msleep(1); +} + +/** + * igb_get_pcs_speed_and_duplex_82575 - Retrieve current speed/duplex + * @hw: pointer to the HW structure + * @speed: stores the current speed + * @duplex: stores the current duplex + * + * Using the physical coding sub-layer (PCS), retrieve the current speed and + * duplex, then store the values in the pointers provided. + **/ +static s32 igb_get_pcs_speed_and_duplex_82575(struct e1000_hw *hw, u16 *speed, + u16 *duplex) +{ + struct e1000_mac_info *mac = &hw->mac; + u32 pcs; + + /* Set up defaults for the return values of this function */ + mac->serdes_has_link = false; + *speed = 0; + *duplex = 0; + + /* + * Read the PCS Status register for link state. For non-copper mode, + * the status register is not accurate. The PCS status register is + * used instead. + */ + pcs = rd32(E1000_PCS_LSTAT); + + /* + * The link up bit determines when link is up on autoneg. The sync ok + * gets set once both sides sync up and agree upon link. Stable link + * can be determined by checking for both link up and link sync ok + */ + if ((pcs & E1000_PCS_LSTS_LINK_OK) && (pcs & E1000_PCS_LSTS_SYNK_OK)) { + mac->serdes_has_link = true; + + /* Detect and store PCS speed */ + if (pcs & E1000_PCS_LSTS_SPEED_1000) { + *speed = SPEED_1000; + } else if (pcs & E1000_PCS_LSTS_SPEED_100) { + *speed = SPEED_100; + } else { + *speed = SPEED_10; + } + + /* Detect and store PCS duplex */ + if (pcs & E1000_PCS_LSTS_DUPLEX_FULL) { + *duplex = FULL_DUPLEX; + } else { + *duplex = HALF_DUPLEX; + } + } + + return 0; +} + +/** + * igb_shutdown_serdes_link_82575 - Remove link during power down + * @hw: pointer to the HW structure + * + * In the case of fiber serdes, shut down optics and PCS on driver unload + * when management pass thru is not enabled. + **/ +void igb_shutdown_serdes_link_82575(struct e1000_hw *hw) +{ + u32 reg; + + if (hw->phy.media_type != e1000_media_type_internal_serdes && + igb_sgmii_active_82575(hw)) + return; + + if (!igb_enable_mng_pass_thru(hw)) { + /* Disable PCS to turn off link */ + reg = rd32(E1000_PCS_CFG0); + reg &= ~E1000_PCS_CFG_PCS_EN; + wr32(E1000_PCS_CFG0, reg); + + /* shutdown the laser */ + reg = rd32(E1000_CTRL_EXT); + reg |= E1000_CTRL_EXT_SDP3_DATA; + wr32(E1000_CTRL_EXT, reg); + + /* flush the write to verify completion */ + wrfl(); + msleep(1); + } +} + +/** + * igb_reset_hw_82575 - Reset hardware + * @hw: pointer to the HW structure + * + * This resets the hardware into a known state. This is a + * function pointer entry point called by the api module. + **/ +static s32 igb_reset_hw_82575(struct e1000_hw *hw) +{ + u32 ctrl, icr; + s32 ret_val; + + /* + * Prevent the PCI-E bus from sticking if there is no TLP connection + * on the last TLP read/write transaction when MAC is reset. + */ + ret_val = igb_disable_pcie_master(hw); + if (ret_val) + hw_dbg("PCI-E Master disable polling has failed.\n"); + + /* set the completion timeout for interface */ + ret_val = igb_set_pcie_completion_timeout(hw); + if (ret_val) { + hw_dbg("PCI-E Set completion timeout has failed.\n"); + } + + hw_dbg("Masking off all interrupts\n"); + wr32(E1000_IMC, 0xffffffff); + + wr32(E1000_RCTL, 0); + wr32(E1000_TCTL, E1000_TCTL_PSP); + wrfl(); + + msleep(10); + + ctrl = rd32(E1000_CTRL); + + hw_dbg("Issuing a global reset to MAC\n"); + wr32(E1000_CTRL, ctrl | E1000_CTRL_RST); + + ret_val = igb_get_auto_rd_done(hw); + if (ret_val) { + /* + * When auto config read does not complete, do not + * return with an error. This can happen in situations + * where there is no eeprom and prevents getting link. + */ + hw_dbg("Auto Read Done did not complete\n"); + } + + /* If EEPROM is not present, run manual init scripts */ + if ((rd32(E1000_EECD) & E1000_EECD_PRES) == 0) + igb_reset_init_script_82575(hw); + + /* Clear any pending interrupt events. */ + wr32(E1000_IMC, 0xffffffff); + icr = rd32(E1000_ICR); + + /* Install any alternate MAC address into RAR0 */ + ret_val = igb_check_alt_mac_addr(hw); + + return ret_val; +} + +/** + * igb_init_hw_82575 - Initialize hardware + * @hw: pointer to the HW structure + * + * This inits the hardware readying it for operation. + **/ +static s32 igb_init_hw_82575(struct e1000_hw *hw) +{ + struct e1000_mac_info *mac = &hw->mac; + s32 ret_val; + u16 i, rar_count = mac->rar_entry_count; + + /* Initialize identification LED */ + ret_val = igb_id_led_init(hw); + if (ret_val) { + hw_dbg("Error initializing identification LED\n"); + /* This is not fatal and we should not stop init due to this */ + } + + /* Disabling VLAN filtering */ + hw_dbg("Initializing the IEEE VLAN\n"); + if (hw->mac.type == e1000_i350) + igb_clear_vfta_i350(hw); + else + igb_clear_vfta(hw); + + /* Setup the receive address */ + igb_init_rx_addrs(hw, rar_count); + + /* Zero out the Multicast HASH table */ + hw_dbg("Zeroing the MTA\n"); + for (i = 0; i < mac->mta_reg_count; i++) + array_wr32(E1000_MTA, i, 0); + + /* Zero out the Unicast HASH table */ + hw_dbg("Zeroing the UTA\n"); + for (i = 0; i < mac->uta_reg_count; i++) + array_wr32(E1000_UTA, i, 0); + + /* Setup link and flow control */ + ret_val = igb_setup_link(hw); + + /* + * Clear all of the statistics registers (clear on read). It is + * important that we do this after we have tried to establish link + * because the symbol error count will increment wildly if there + * is no link. + */ + igb_clear_hw_cntrs_82575(hw); + + return ret_val; +} + +/** + * igb_setup_copper_link_82575 - Configure copper link settings + * @hw: pointer to the HW structure + * + * Configures the link for auto-neg or forced speed and duplex. Then we check + * for link, once link is established calls to configure collision distance + * and flow control are called. + **/ +static s32 igb_setup_copper_link_82575(struct e1000_hw *hw) +{ + u32 ctrl; + s32 ret_val; + + ctrl = rd32(E1000_CTRL); + ctrl |= E1000_CTRL_SLU; + ctrl &= ~(E1000_CTRL_FRCSPD | E1000_CTRL_FRCDPX); + wr32(E1000_CTRL, ctrl); + + ret_val = igb_setup_serdes_link_82575(hw); + if (ret_val) + goto out; + + if (igb_sgmii_active_82575(hw) && !hw->phy.reset_disable) { + /* allow time for SFP cage time to power up phy */ + msleep(300); + + ret_val = hw->phy.ops.reset(hw); + if (ret_val) { + hw_dbg("Error resetting the PHY.\n"); + goto out; + } + } + switch (hw->phy.type) { + case e1000_phy_m88: + if (hw->phy.id == I347AT4_E_PHY_ID || + hw->phy.id == M88E1112_E_PHY_ID) + ret_val = igb_copper_link_setup_m88_gen2(hw); + else + ret_val = igb_copper_link_setup_m88(hw); + break; + case e1000_phy_igp_3: + ret_val = igb_copper_link_setup_igp(hw); + break; + case e1000_phy_82580: + ret_val = igb_copper_link_setup_82580(hw); + break; + default: + ret_val = -E1000_ERR_PHY; + break; + } + + if (ret_val) + goto out; + + ret_val = igb_setup_copper_link(hw); +out: + return ret_val; +} + +/** + * igb_setup_serdes_link_82575 - Setup link for serdes + * @hw: pointer to the HW structure + * + * Configure the physical coding sub-layer (PCS) link. The PCS link is + * used on copper connections where the serialized gigabit media independent + * interface (sgmii), or serdes fiber is being used. Configures the link + * for auto-negotiation or forces speed/duplex. + **/ +static s32 igb_setup_serdes_link_82575(struct e1000_hw *hw) +{ + u32 ctrl_ext, ctrl_reg, reg; + bool pcs_autoneg; + s32 ret_val = E1000_SUCCESS; + u16 data; + + if ((hw->phy.media_type != e1000_media_type_internal_serdes) && + !igb_sgmii_active_82575(hw)) + return ret_val; + + + /* + * On the 82575, SerDes loopback mode persists until it is + * explicitly turned off or a power cycle is performed. A read to + * the register does not indicate its status. Therefore, we ensure + * loopback mode is disabled during initialization. + */ + wr32(E1000_SCTL, E1000_SCTL_DISABLE_SERDES_LOOPBACK); + + /* power on the sfp cage if present */ + ctrl_ext = rd32(E1000_CTRL_EXT); + ctrl_ext &= ~E1000_CTRL_EXT_SDP3_DATA; + wr32(E1000_CTRL_EXT, ctrl_ext); + + ctrl_reg = rd32(E1000_CTRL); + ctrl_reg |= E1000_CTRL_SLU; + + if (hw->mac.type == e1000_82575 || hw->mac.type == e1000_82576) { + /* set both sw defined pins */ + ctrl_reg |= E1000_CTRL_SWDPIN0 | E1000_CTRL_SWDPIN1; + + /* Set switch control to serdes energy detect */ + reg = rd32(E1000_CONNSW); + reg |= E1000_CONNSW_ENRGSRC; + wr32(E1000_CONNSW, reg); + } + + reg = rd32(E1000_PCS_LCTL); + + /* default pcs_autoneg to the same setting as mac autoneg */ + pcs_autoneg = hw->mac.autoneg; + + switch (ctrl_ext & E1000_CTRL_EXT_LINK_MODE_MASK) { + case E1000_CTRL_EXT_LINK_MODE_SGMII: + /* sgmii mode lets the phy handle forcing speed/duplex */ + pcs_autoneg = true; + /* autoneg time out should be disabled for SGMII mode */ + reg &= ~(E1000_PCS_LCTL_AN_TIMEOUT); + break; + case E1000_CTRL_EXT_LINK_MODE_1000BASE_KX: + /* disable PCS autoneg and support parallel detect only */ + pcs_autoneg = false; + default: + if (hw->mac.type == e1000_82575 || + hw->mac.type == e1000_82576) { + ret_val = hw->nvm.ops.read(hw, NVM_COMPAT, 1, &data); + if (ret_val) { + printk(KERN_DEBUG "NVM Read Error\n\n"); + return ret_val; + } + + if (data & E1000_EEPROM_PCS_AUTONEG_DISABLE_BIT) + pcs_autoneg = false; + } + + /* + * non-SGMII modes only supports a speed of 1000/Full for the + * link so it is best to just force the MAC and let the pcs + * link either autoneg or be forced to 1000/Full + */ + ctrl_reg |= E1000_CTRL_SPD_1000 | E1000_CTRL_FRCSPD | + E1000_CTRL_FD | E1000_CTRL_FRCDPX; + + /* set speed of 1000/Full if speed/duplex is forced */ + reg |= E1000_PCS_LCTL_FSV_1000 | E1000_PCS_LCTL_FDV_FULL; + break; + } + + wr32(E1000_CTRL, ctrl_reg); + + /* + * New SerDes mode allows for forcing speed or autonegotiating speed + * at 1gb. Autoneg should be default set by most drivers. This is the + * mode that will be compatible with older link partners and switches. + * However, both are supported by the hardware and some drivers/tools. + */ + reg &= ~(E1000_PCS_LCTL_AN_ENABLE | E1000_PCS_LCTL_FLV_LINK_UP | + E1000_PCS_LCTL_FSD | E1000_PCS_LCTL_FORCE_LINK); + + /* + * We force flow control to prevent the CTRL register values from being + * overwritten by the autonegotiated flow control values + */ + reg |= E1000_PCS_LCTL_FORCE_FCTRL; + + if (pcs_autoneg) { + /* Set PCS register for autoneg */ + reg |= E1000_PCS_LCTL_AN_ENABLE | /* Enable Autoneg */ + E1000_PCS_LCTL_AN_RESTART; /* Restart autoneg */ + hw_dbg("Configuring Autoneg:PCS_LCTL=0x%08X\n", reg); + } else { + /* Set PCS register for forced link */ + reg |= E1000_PCS_LCTL_FSD; /* Force Speed */ + + hw_dbg("Configuring Forced Link:PCS_LCTL=0x%08X\n", reg); + } + + wr32(E1000_PCS_LCTL, reg); + + if (!igb_sgmii_active_82575(hw)) + igb_force_mac_fc(hw); + + return ret_val; +} + +/** + * igb_sgmii_active_82575 - Return sgmii state + * @hw: pointer to the HW structure + * + * 82575 silicon has a serialized gigabit media independent interface (sgmii) + * which can be enabled for use in the embedded applications. Simply + * return the current state of the sgmii interface. + **/ +static bool igb_sgmii_active_82575(struct e1000_hw *hw) +{ + struct e1000_dev_spec_82575 *dev_spec = &hw->dev_spec._82575; + return dev_spec->sgmii_active; +} + +/** + * igb_reset_init_script_82575 - Inits HW defaults after reset + * @hw: pointer to the HW structure + * + * Inits recommended HW defaults after a reset when there is no EEPROM + * detected. This is only for the 82575. + **/ +static s32 igb_reset_init_script_82575(struct e1000_hw *hw) +{ + if (hw->mac.type == e1000_82575) { + hw_dbg("Running reset init script for 82575\n"); + /* SerDes configuration via SERDESCTRL */ + igb_write_8bit_ctrl_reg(hw, E1000_SCTL, 0x00, 0x0C); + igb_write_8bit_ctrl_reg(hw, E1000_SCTL, 0x01, 0x78); + igb_write_8bit_ctrl_reg(hw, E1000_SCTL, 0x1B, 0x23); + igb_write_8bit_ctrl_reg(hw, E1000_SCTL, 0x23, 0x15); + + /* CCM configuration via CCMCTL register */ + igb_write_8bit_ctrl_reg(hw, E1000_CCMCTL, 0x14, 0x00); + igb_write_8bit_ctrl_reg(hw, E1000_CCMCTL, 0x10, 0x00); + + /* PCIe lanes configuration */ + igb_write_8bit_ctrl_reg(hw, E1000_GIOCTL, 0x00, 0xEC); + igb_write_8bit_ctrl_reg(hw, E1000_GIOCTL, 0x61, 0xDF); + igb_write_8bit_ctrl_reg(hw, E1000_GIOCTL, 0x34, 0x05); + igb_write_8bit_ctrl_reg(hw, E1000_GIOCTL, 0x2F, 0x81); + + /* PCIe PLL Configuration */ + igb_write_8bit_ctrl_reg(hw, E1000_SCCTL, 0x02, 0x47); + igb_write_8bit_ctrl_reg(hw, E1000_SCCTL, 0x14, 0x00); + igb_write_8bit_ctrl_reg(hw, E1000_SCCTL, 0x10, 0x00); + } + + return 0; +} + +/** + * igb_read_mac_addr_82575 - Read device MAC address + * @hw: pointer to the HW structure + **/ +static s32 igb_read_mac_addr_82575(struct e1000_hw *hw) +{ + s32 ret_val = 0; + + /* + * If there's an alternate MAC address place it in RAR0 + * so that it will override the Si installed default perm + * address. + */ + ret_val = igb_check_alt_mac_addr(hw); + if (ret_val) + goto out; + + ret_val = igb_read_mac_addr(hw); + +out: + return ret_val; +} + +/** + * igb_power_down_phy_copper_82575 - Remove link during PHY power down + * @hw: pointer to the HW structure + * + * In the case of a PHY power down to save power, or to turn off link during a + * driver unload, or wake on lan is not enabled, remove the link. + **/ +void igb_power_down_phy_copper_82575(struct e1000_hw *hw) +{ + /* If the management interface is not enabled, then power down */ + if (!(igb_enable_mng_pass_thru(hw) || igb_check_reset_block(hw))) + igb_power_down_phy_copper(hw); +} + +/** + * igb_clear_hw_cntrs_82575 - Clear device specific hardware counters + * @hw: pointer to the HW structure + * + * Clears the hardware counters by reading the counter registers. + **/ +static void igb_clear_hw_cntrs_82575(struct e1000_hw *hw) +{ + igb_clear_hw_cntrs_base(hw); + + rd32(E1000_PRC64); + rd32(E1000_PRC127); + rd32(E1000_PRC255); + rd32(E1000_PRC511); + rd32(E1000_PRC1023); + rd32(E1000_PRC1522); + rd32(E1000_PTC64); + rd32(E1000_PTC127); + rd32(E1000_PTC255); + rd32(E1000_PTC511); + rd32(E1000_PTC1023); + rd32(E1000_PTC1522); + + rd32(E1000_ALGNERRC); + rd32(E1000_RXERRC); + rd32(E1000_TNCRS); + rd32(E1000_CEXTERR); + rd32(E1000_TSCTC); + rd32(E1000_TSCTFC); + + rd32(E1000_MGTPRC); + rd32(E1000_MGTPDC); + rd32(E1000_MGTPTC); + + rd32(E1000_IAC); + rd32(E1000_ICRXOC); + + rd32(E1000_ICRXPTC); + rd32(E1000_ICRXATC); + rd32(E1000_ICTXPTC); + rd32(E1000_ICTXATC); + rd32(E1000_ICTXQEC); + rd32(E1000_ICTXQMTC); + rd32(E1000_ICRXDMTC); + + rd32(E1000_CBTMPC); + rd32(E1000_HTDPMC); + rd32(E1000_CBRMPC); + rd32(E1000_RPTHC); + rd32(E1000_HGPTC); + rd32(E1000_HTCBDPC); + rd32(E1000_HGORCL); + rd32(E1000_HGORCH); + rd32(E1000_HGOTCL); + rd32(E1000_HGOTCH); + rd32(E1000_LENERRS); + + /* This register should not be read in copper configurations */ + if (hw->phy.media_type == e1000_media_type_internal_serdes || + igb_sgmii_active_82575(hw)) + rd32(E1000_SCVPC); +} + +/** + * igb_rx_fifo_flush_82575 - Clean rx fifo after RX enable + * @hw: pointer to the HW structure + * + * After rx enable if managability is enabled then there is likely some + * bad data at the start of the fifo and possibly in the DMA fifo. This + * function clears the fifos and flushes any packets that came in as rx was + * being enabled. + **/ +void igb_rx_fifo_flush_82575(struct e1000_hw *hw) +{ + u32 rctl, rlpml, rxdctl[4], rfctl, temp_rctl, rx_enabled; + int i, ms_wait; + + if (hw->mac.type != e1000_82575 || + !(rd32(E1000_MANC) & E1000_MANC_RCV_TCO_EN)) + return; + + /* Disable all RX queues */ + for (i = 0; i < 4; i++) { + rxdctl[i] = rd32(E1000_RXDCTL(i)); + wr32(E1000_RXDCTL(i), + rxdctl[i] & ~E1000_RXDCTL_QUEUE_ENABLE); + } + /* Poll all queues to verify they have shut down */ + for (ms_wait = 0; ms_wait < 10; ms_wait++) { + msleep(1); + rx_enabled = 0; + for (i = 0; i < 4; i++) + rx_enabled |= rd32(E1000_RXDCTL(i)); + if (!(rx_enabled & E1000_RXDCTL_QUEUE_ENABLE)) + break; + } + + if (ms_wait == 10) + hw_dbg("Queue disable timed out after 10ms\n"); + + /* Clear RLPML, RCTL.SBP, RFCTL.LEF, and set RCTL.LPE so that all + * incoming packets are rejected. Set enable and wait 2ms so that + * any packet that was coming in as RCTL.EN was set is flushed + */ + rfctl = rd32(E1000_RFCTL); + wr32(E1000_RFCTL, rfctl & ~E1000_RFCTL_LEF); + + rlpml = rd32(E1000_RLPML); + wr32(E1000_RLPML, 0); + + rctl = rd32(E1000_RCTL); + temp_rctl = rctl & ~(E1000_RCTL_EN | E1000_RCTL_SBP); + temp_rctl |= E1000_RCTL_LPE; + + wr32(E1000_RCTL, temp_rctl); + wr32(E1000_RCTL, temp_rctl | E1000_RCTL_EN); + wrfl(); + msleep(2); + + /* Enable RX queues that were previously enabled and restore our + * previous state + */ + for (i = 0; i < 4; i++) + wr32(E1000_RXDCTL(i), rxdctl[i]); + wr32(E1000_RCTL, rctl); + wrfl(); + + wr32(E1000_RLPML, rlpml); + wr32(E1000_RFCTL, rfctl); + + /* Flush receive errors generated by workaround */ + rd32(E1000_ROC); + rd32(E1000_RNBC); + rd32(E1000_MPC); +} + +/** + * igb_set_pcie_completion_timeout - set pci-e completion timeout + * @hw: pointer to the HW structure + * + * The defaults for 82575 and 82576 should be in the range of 50us to 50ms, + * however the hardware default for these parts is 500us to 1ms which is less + * than the 10ms recommended by the pci-e spec. To address this we need to + * increase the value to either 10ms to 200ms for capability version 1 config, + * or 16ms to 55ms for version 2. + **/ +static s32 igb_set_pcie_completion_timeout(struct e1000_hw *hw) +{ + u32 gcr = rd32(E1000_GCR); + s32 ret_val = 0; + u16 pcie_devctl2; + + /* only take action if timeout value is defaulted to 0 */ + if (gcr & E1000_GCR_CMPL_TMOUT_MASK) + goto out; + + /* + * if capababilities version is type 1 we can write the + * timeout of 10ms to 200ms through the GCR register + */ + if (!(gcr & E1000_GCR_CAP_VER2)) { + gcr |= E1000_GCR_CMPL_TMOUT_10ms; + goto out; + } + + /* + * for version 2 capabilities we need to write the config space + * directly in order to set the completion timeout value for + * 16ms to 55ms + */ + ret_val = igb_read_pcie_cap_reg(hw, PCIE_DEVICE_CONTROL2, + &pcie_devctl2); + if (ret_val) + goto out; + + pcie_devctl2 |= PCIE_DEVICE_CONTROL2_16ms; + + ret_val = igb_write_pcie_cap_reg(hw, PCIE_DEVICE_CONTROL2, + &pcie_devctl2); +out: + /* disable completion timeout resend */ + gcr &= ~E1000_GCR_CMPL_TMOUT_RESEND; + + wr32(E1000_GCR, gcr); + return ret_val; +} + +/** + * igb_vmdq_set_anti_spoofing_pf - enable or disable anti-spoofing + * @hw: pointer to the hardware struct + * @enable: state to enter, either enabled or disabled + * @pf: Physical Function pool - do not set anti-spoofing for the PF + * + * enables/disables L2 switch anti-spoofing functionality. + **/ +void igb_vmdq_set_anti_spoofing_pf(struct e1000_hw *hw, bool enable, int pf) +{ + u32 dtxswc; + + switch (hw->mac.type) { + case e1000_82576: + case e1000_i350: + dtxswc = rd32(E1000_DTXSWC); + if (enable) { + dtxswc |= (E1000_DTXSWC_MAC_SPOOF_MASK | + E1000_DTXSWC_VLAN_SPOOF_MASK); + /* The PF can spoof - it has to in order to + * support emulation mode NICs */ + dtxswc ^= (1 << pf | 1 << (pf + MAX_NUM_VFS)); + } else { + dtxswc &= ~(E1000_DTXSWC_MAC_SPOOF_MASK | + E1000_DTXSWC_VLAN_SPOOF_MASK); + } + wr32(E1000_DTXSWC, dtxswc); + break; + default: + break; + } +} + +/** + * igb_vmdq_set_loopback_pf - enable or disable vmdq loopback + * @hw: pointer to the hardware struct + * @enable: state to enter, either enabled or disabled + * + * enables/disables L2 switch loopback functionality. + **/ +void igb_vmdq_set_loopback_pf(struct e1000_hw *hw, bool enable) +{ + u32 dtxswc; + + switch (hw->mac.type) { + case e1000_82576: + dtxswc = rd32(E1000_DTXSWC); + if (enable) + dtxswc |= E1000_DTXSWC_VMDQ_LOOPBACK_EN; + else + dtxswc &= ~E1000_DTXSWC_VMDQ_LOOPBACK_EN; + wr32(E1000_DTXSWC, dtxswc); + break; + case e1000_i350: + dtxswc = rd32(E1000_TXSWC); + if (enable) + dtxswc |= E1000_DTXSWC_VMDQ_LOOPBACK_EN; + else + dtxswc &= ~E1000_DTXSWC_VMDQ_LOOPBACK_EN; + wr32(E1000_TXSWC, dtxswc); + break; + default: + /* Currently no other hardware supports loopback */ + break; + } + + +} + +/** + * igb_vmdq_set_replication_pf - enable or disable vmdq replication + * @hw: pointer to the hardware struct + * @enable: state to enter, either enabled or disabled + * + * enables/disables replication of packets across multiple pools. + **/ +void igb_vmdq_set_replication_pf(struct e1000_hw *hw, bool enable) +{ + u32 vt_ctl = rd32(E1000_VT_CTL); + + if (enable) + vt_ctl |= E1000_VT_CTL_VM_REPL_EN; + else + vt_ctl &= ~E1000_VT_CTL_VM_REPL_EN; + + wr32(E1000_VT_CTL, vt_ctl); +} + +/** + * igb_read_phy_reg_82580 - Read 82580 MDI control register + * @hw: pointer to the HW structure + * @offset: register offset to be read + * @data: pointer to the read data + * + * Reads the MDI control register in the PHY at offset and stores the + * information read to data. + **/ +static s32 igb_read_phy_reg_82580(struct e1000_hw *hw, u32 offset, u16 *data) +{ + s32 ret_val; + + + ret_val = hw->phy.ops.acquire(hw); + if (ret_val) + goto out; + + ret_val = igb_read_phy_reg_mdic(hw, offset, data); + + hw->phy.ops.release(hw); + +out: + return ret_val; +} + +/** + * igb_write_phy_reg_82580 - Write 82580 MDI control register + * @hw: pointer to the HW structure + * @offset: register offset to write to + * @data: data to write to register at offset + * + * Writes data to MDI control register in the PHY at offset. + **/ +static s32 igb_write_phy_reg_82580(struct e1000_hw *hw, u32 offset, u16 data) +{ + s32 ret_val; + + + ret_val = hw->phy.ops.acquire(hw); + if (ret_val) + goto out; + + ret_val = igb_write_phy_reg_mdic(hw, offset, data); + + hw->phy.ops.release(hw); + +out: + return ret_val; +} + +/** + * igb_reset_mdicnfg_82580 - Reset MDICNFG destination and com_mdio bits + * @hw: pointer to the HW structure + * + * This resets the the MDICNFG.Destination and MDICNFG.Com_MDIO bits based on + * the values found in the EEPROM. This addresses an issue in which these + * bits are not restored from EEPROM after reset. + **/ +static s32 igb_reset_mdicnfg_82580(struct e1000_hw *hw) +{ + s32 ret_val = 0; + u32 mdicnfg; + u16 nvm_data = 0; + + if (hw->mac.type != e1000_82580) + goto out; + if (!igb_sgmii_active_82575(hw)) + goto out; + + ret_val = hw->nvm.ops.read(hw, NVM_INIT_CONTROL3_PORT_A + + NVM_82580_LAN_FUNC_OFFSET(hw->bus.func), 1, + &nvm_data); + if (ret_val) { + hw_dbg("NVM Read Error\n"); + goto out; + } + + mdicnfg = rd32(E1000_MDICNFG); + if (nvm_data & NVM_WORD24_EXT_MDIO) + mdicnfg |= E1000_MDICNFG_EXT_MDIO; + if (nvm_data & NVM_WORD24_COM_MDIO) + mdicnfg |= E1000_MDICNFG_COM_MDIO; + wr32(E1000_MDICNFG, mdicnfg); +out: + return ret_val; +} + +/** + * igb_reset_hw_82580 - Reset hardware + * @hw: pointer to the HW structure + * + * This resets function or entire device (all ports, etc.) + * to a known state. + **/ +static s32 igb_reset_hw_82580(struct e1000_hw *hw) +{ + s32 ret_val = 0; + /* BH SW mailbox bit in SW_FW_SYNC */ + u16 swmbsw_mask = E1000_SW_SYNCH_MB; + u32 ctrl, icr; + bool global_device_reset = hw->dev_spec._82575.global_device_reset; + + + hw->dev_spec._82575.global_device_reset = false; + + /* Get current control state. */ + ctrl = rd32(E1000_CTRL); + + /* + * Prevent the PCI-E bus from sticking if there is no TLP connection + * on the last TLP read/write transaction when MAC is reset. + */ + ret_val = igb_disable_pcie_master(hw); + if (ret_val) + hw_dbg("PCI-E Master disable polling has failed.\n"); + + hw_dbg("Masking off all interrupts\n"); + wr32(E1000_IMC, 0xffffffff); + wr32(E1000_RCTL, 0); + wr32(E1000_TCTL, E1000_TCTL_PSP); + wrfl(); + + msleep(10); + + /* Determine whether or not a global dev reset is requested */ + if (global_device_reset && + igb_acquire_swfw_sync_82575(hw, swmbsw_mask)) + global_device_reset = false; + + if (global_device_reset && + !(rd32(E1000_STATUS) & E1000_STAT_DEV_RST_SET)) + ctrl |= E1000_CTRL_DEV_RST; + else + ctrl |= E1000_CTRL_RST; + + wr32(E1000_CTRL, ctrl); + wrfl(); + + /* Add delay to insure DEV_RST has time to complete */ + if (global_device_reset) + msleep(5); + + ret_val = igb_get_auto_rd_done(hw); + if (ret_val) { + /* + * When auto config read does not complete, do not + * return with an error. This can happen in situations + * where there is no eeprom and prevents getting link. + */ + hw_dbg("Auto Read Done did not complete\n"); + } + + /* If EEPROM is not present, run manual init scripts */ + if ((rd32(E1000_EECD) & E1000_EECD_PRES) == 0) + igb_reset_init_script_82575(hw); + + /* clear global device reset status bit */ + wr32(E1000_STATUS, E1000_STAT_DEV_RST_SET); + + /* Clear any pending interrupt events. */ + wr32(E1000_IMC, 0xffffffff); + icr = rd32(E1000_ICR); + + ret_val = igb_reset_mdicnfg_82580(hw); + if (ret_val) + hw_dbg("Could not reset MDICNFG based on EEPROM\n"); + + /* Install any alternate MAC address into RAR0 */ + ret_val = igb_check_alt_mac_addr(hw); + + /* Release semaphore */ + if (global_device_reset) + igb_release_swfw_sync_82575(hw, swmbsw_mask); + + return ret_val; +} + +/** + * igb_rxpbs_adjust_82580 - adjust RXPBS value to reflect actual RX PBA size + * @data: data received by reading RXPBS register + * + * The 82580 uses a table based approach for packet buffer allocation sizes. + * This function converts the retrieved value into the correct table value + * 0x0 0x1 0x2 0x3 0x4 0x5 0x6 0x7 + * 0x0 36 72 144 1 2 4 8 16 + * 0x8 35 70 140 rsv rsv rsv rsv rsv + */ +u16 igb_rxpbs_adjust_82580(u32 data) +{ + u16 ret_val = 0; + + if (data < E1000_82580_RXPBS_TABLE_SIZE) + ret_val = e1000_82580_rxpbs_table[data]; + + return ret_val; +} + +/** + * igb_validate_nvm_checksum_with_offset - Validate EEPROM + * checksum + * @hw: pointer to the HW structure + * @offset: offset in words of the checksum protected region + * + * Calculates the EEPROM checksum by reading/adding each word of the EEPROM + * and then verifies that the sum of the EEPROM is equal to 0xBABA. + **/ +static s32 igb_validate_nvm_checksum_with_offset(struct e1000_hw *hw, + u16 offset) +{ + s32 ret_val = 0; + u16 checksum = 0; + u16 i, nvm_data; + + for (i = offset; i < ((NVM_CHECKSUM_REG + offset) + 1); i++) { + ret_val = hw->nvm.ops.read(hw, i, 1, &nvm_data); + if (ret_val) { + hw_dbg("NVM Read Error\n"); + goto out; + } + checksum += nvm_data; + } + + if (checksum != (u16) NVM_SUM) { + hw_dbg("NVM Checksum Invalid\n"); + ret_val = -E1000_ERR_NVM; + goto out; + } + +out: + return ret_val; +} + +/** + * igb_update_nvm_checksum_with_offset - Update EEPROM + * checksum + * @hw: pointer to the HW structure + * @offset: offset in words of the checksum protected region + * + * Updates the EEPROM checksum by reading/adding each word of the EEPROM + * up to the checksum. Then calculates the EEPROM checksum and writes the + * value to the EEPROM. + **/ +static s32 igb_update_nvm_checksum_with_offset(struct e1000_hw *hw, u16 offset) +{ + s32 ret_val; + u16 checksum = 0; + u16 i, nvm_data; + + for (i = offset; i < (NVM_CHECKSUM_REG + offset); i++) { + ret_val = hw->nvm.ops.read(hw, i, 1, &nvm_data); + if (ret_val) { + hw_dbg("NVM Read Error while updating checksum.\n"); + goto out; + } + checksum += nvm_data; + } + checksum = (u16) NVM_SUM - checksum; + ret_val = hw->nvm.ops.write(hw, (NVM_CHECKSUM_REG + offset), 1, + &checksum); + if (ret_val) + hw_dbg("NVM Write Error while updating checksum.\n"); + +out: + return ret_val; +} + +/** + * igb_validate_nvm_checksum_82580 - Validate EEPROM checksum + * @hw: pointer to the HW structure + * + * Calculates the EEPROM section checksum by reading/adding each word of + * the EEPROM and then verifies that the sum of the EEPROM is + * equal to 0xBABA. + **/ +static s32 igb_validate_nvm_checksum_82580(struct e1000_hw *hw) +{ + s32 ret_val = 0; + u16 eeprom_regions_count = 1; + u16 j, nvm_data; + u16 nvm_offset; + + ret_val = hw->nvm.ops.read(hw, NVM_COMPATIBILITY_REG_3, 1, &nvm_data); + if (ret_val) { + hw_dbg("NVM Read Error\n"); + goto out; + } + + if (nvm_data & NVM_COMPATIBILITY_BIT_MASK) { + /* if checksums compatibility bit is set validate checksums + * for all 4 ports. */ + eeprom_regions_count = 4; + } + + for (j = 0; j < eeprom_regions_count; j++) { + nvm_offset = NVM_82580_LAN_FUNC_OFFSET(j); + ret_val = igb_validate_nvm_checksum_with_offset(hw, + nvm_offset); + if (ret_val != 0) + goto out; + } + +out: + return ret_val; +} + +/** + * igb_update_nvm_checksum_82580 - Update EEPROM checksum + * @hw: pointer to the HW structure + * + * Updates the EEPROM section checksums for all 4 ports by reading/adding + * each word of the EEPROM up to the checksum. Then calculates the EEPROM + * checksum and writes the value to the EEPROM. + **/ +static s32 igb_update_nvm_checksum_82580(struct e1000_hw *hw) +{ + s32 ret_val; + u16 j, nvm_data; + u16 nvm_offset; + + ret_val = hw->nvm.ops.read(hw, NVM_COMPATIBILITY_REG_3, 1, &nvm_data); + if (ret_val) { + hw_dbg("NVM Read Error while updating checksum" + " compatibility bit.\n"); + goto out; + } + + if ((nvm_data & NVM_COMPATIBILITY_BIT_MASK) == 0) { + /* set compatibility bit to validate checksums appropriately */ + nvm_data = nvm_data | NVM_COMPATIBILITY_BIT_MASK; + ret_val = hw->nvm.ops.write(hw, NVM_COMPATIBILITY_REG_3, 1, + &nvm_data); + if (ret_val) { + hw_dbg("NVM Write Error while updating checksum" + " compatibility bit.\n"); + goto out; + } + } + + for (j = 0; j < 4; j++) { + nvm_offset = NVM_82580_LAN_FUNC_OFFSET(j); + ret_val = igb_update_nvm_checksum_with_offset(hw, nvm_offset); + if (ret_val) + goto out; + } + +out: + return ret_val; +} + +/** + * igb_validate_nvm_checksum_i350 - Validate EEPROM checksum + * @hw: pointer to the HW structure + * + * Calculates the EEPROM section checksum by reading/adding each word of + * the EEPROM and then verifies that the sum of the EEPROM is + * equal to 0xBABA. + **/ +static s32 igb_validate_nvm_checksum_i350(struct e1000_hw *hw) +{ + s32 ret_val = 0; + u16 j; + u16 nvm_offset; + + for (j = 0; j < 4; j++) { + nvm_offset = NVM_82580_LAN_FUNC_OFFSET(j); + ret_val = igb_validate_nvm_checksum_with_offset(hw, + nvm_offset); + if (ret_val != 0) + goto out; + } + +out: + return ret_val; +} + +/** + * igb_update_nvm_checksum_i350 - Update EEPROM checksum + * @hw: pointer to the HW structure + * + * Updates the EEPROM section checksums for all 4 ports by reading/adding + * each word of the EEPROM up to the checksum. Then calculates the EEPROM + * checksum and writes the value to the EEPROM. + **/ +static s32 igb_update_nvm_checksum_i350(struct e1000_hw *hw) +{ + s32 ret_val = 0; + u16 j; + u16 nvm_offset; + + for (j = 0; j < 4; j++) { + nvm_offset = NVM_82580_LAN_FUNC_OFFSET(j); + ret_val = igb_update_nvm_checksum_with_offset(hw, nvm_offset); + if (ret_val != 0) + goto out; + } + +out: + return ret_val; +} + +/** + * igb_set_eee_i350 - Enable/disable EEE support + * @hw: pointer to the HW structure + * + * Enable/disable EEE based on setting in dev_spec structure. + * + **/ +s32 igb_set_eee_i350(struct e1000_hw *hw) +{ + s32 ret_val = 0; + u32 ipcnfg, eeer, ctrl_ext; + + ctrl_ext = rd32(E1000_CTRL_EXT); + if ((hw->mac.type != e1000_i350) || + (ctrl_ext & E1000_CTRL_EXT_LINK_MODE_MASK)) + goto out; + ipcnfg = rd32(E1000_IPCNFG); + eeer = rd32(E1000_EEER); + + /* enable or disable per user setting */ + if (!(hw->dev_spec._82575.eee_disable)) { + ipcnfg |= (E1000_IPCNFG_EEE_1G_AN | + E1000_IPCNFG_EEE_100M_AN); + eeer |= (E1000_EEER_TX_LPI_EN | + E1000_EEER_RX_LPI_EN | + E1000_EEER_LPI_FC); + + } else { + ipcnfg &= ~(E1000_IPCNFG_EEE_1G_AN | + E1000_IPCNFG_EEE_100M_AN); + eeer &= ~(E1000_EEER_TX_LPI_EN | + E1000_EEER_RX_LPI_EN | + E1000_EEER_LPI_FC); + } + wr32(E1000_IPCNFG, ipcnfg); + wr32(E1000_EEER, eeer); +out: + + return ret_val; +} + +static struct e1000_mac_operations e1000_mac_ops_82575 = { + .init_hw = igb_init_hw_82575, + .check_for_link = igb_check_for_link_82575, + .rar_set = igb_rar_set, + .read_mac_addr = igb_read_mac_addr_82575, + .get_speed_and_duplex = igb_get_speed_and_duplex_copper, +}; + +static struct e1000_phy_operations e1000_phy_ops_82575 = { + .acquire = igb_acquire_phy_82575, + .get_cfg_done = igb_get_cfg_done_82575, + .release = igb_release_phy_82575, +}; + +static struct e1000_nvm_operations e1000_nvm_ops_82575 = { + .acquire = igb_acquire_nvm_82575, + .read = igb_read_nvm_eerd, + .release = igb_release_nvm_82575, + .write = igb_write_nvm_spi, +}; + +const struct e1000_info e1000_82575_info = { + .get_invariants = igb_get_invariants_82575, + .mac_ops = &e1000_mac_ops_82575, + .phy_ops = &e1000_phy_ops_82575, + .nvm_ops = &e1000_nvm_ops_82575, +}; + |