diff options
Diffstat (limited to 'Documentation/devicetree/bindings')
10 files changed, 343 insertions, 71 deletions
diff --git a/Documentation/devicetree/bindings/bus/ti-gpmc.txt b/Documentation/devicetree/bindings/bus/ti-gpmc.txt index 4b87ea1194e3..704be9306c9f 100644 --- a/Documentation/devicetree/bindings/bus/ti-gpmc.txt +++ b/Documentation/devicetree/bindings/bus/ti-gpmc.txt @@ -95,7 +95,6 @@ GPMC chip-select settings properties for child nodes. All are optional. - gpmc,burst-wrap Enables wrap bursting - gpmc,burst-read Enables read page/burst mode - gpmc,burst-write Enables write page/burst mode -- gpmc,device-nand Device is NAND - gpmc,device-width Total width of device(s) connected to a GPMC chip-select in bytes. The GPMC supports 8-bit and 16-bit devices and so this property must be diff --git a/Documentation/devicetree/bindings/clock/clk-exynos-audss.txt b/Documentation/devicetree/bindings/clock/clk-exynos-audss.txt new file mode 100644 index 000000000000..a1201802f90d --- /dev/null +++ b/Documentation/devicetree/bindings/clock/clk-exynos-audss.txt @@ -0,0 +1,64 @@ +* Samsung Audio Subsystem Clock Controller + +The Samsung Audio Subsystem clock controller generates and supplies clocks +to Audio Subsystem block available in the S5PV210 and Exynos SoCs. The clock +binding described here is applicable to all SoC's in Exynos family. + +Required Properties: + +- compatible: should be one of the following: + - "samsung,exynos4210-audss-clock" - controller compatible with all Exynos4 SoCs. + - "samsung,exynos5250-audss-clock" - controller compatible with all Exynos5 SoCs. + +- reg: physical base address and length of the controller's register set. + +- #clock-cells: should be 1. + +The following is the list of clocks generated by the controller. Each clock is +assigned an identifier and client nodes use this identifier to specify the +clock which they consume. Some of the clocks are available only on a particular +Exynos4 SoC and this is specified where applicable. + +Provided clocks: + +Clock ID SoC (if specific) +----------------------------------------------- + +mout_audss 0 +mout_i2s 1 +dout_srp 2 +dout_aud_bus 3 +dout_i2s 4 +srp_clk 5 +i2s_bus 6 +sclk_i2s 7 +pcm_bus 8 +sclk_pcm 9 + +Example 1: An example of a clock controller node is listed below. + +clock_audss: audss-clock-controller@3810000 { + compatible = "samsung,exynos5250-audss-clock"; + reg = <0x03810000 0x0C>; + #clock-cells = <1>; +}; + +Example 2: I2S controller node that consumes the clock generated by the clock + controller. Refer to the standard clock bindings for information + about 'clocks' and 'clock-names' property. + +i2s0: i2s@03830000 { + compatible = "samsung,i2s-v5"; + reg = <0x03830000 0x100>; + dmas = <&pdma0 10 + &pdma0 9 + &pdma0 8>; + dma-names = "tx", "rx", "tx-sec"; + clocks = <&clock_audss EXYNOS_I2S_BUS>, + <&clock_audss EXYNOS_I2S_BUS>, + <&clock_audss EXYNOS_SCLK_I2S>, + <&clock_audss EXYNOS_MOUT_AUDSS>, + <&clock_audss EXYNOS_MOUT_I2S>; + clock-names = "iis", "i2s_opclk0", "i2s_opclk1", + "mout_audss", "mout_i2s"; +}; diff --git a/Documentation/devicetree/bindings/dma/ste-dma40.txt b/Documentation/devicetree/bindings/dma/ste-dma40.txt new file mode 100644 index 000000000000..bea5b73a7390 --- /dev/null +++ b/Documentation/devicetree/bindings/dma/ste-dma40.txt @@ -0,0 +1,66 @@ +* DMA40 DMA Controller + +Required properties: +- compatible: "stericsson,dma40" +- reg: Address range of the DMAC registers +- reg-names: Names of the above areas to use during resource look-up +- interrupt: Should contain the DMAC interrupt number +- #dma-cells: must be <3> +- memcpy-channels: Channels to be used for memcpy + +Optional properties: +- dma-channels: Number of channels supported by hardware - if not present + the driver will attempt to obtain the information from H/W +- disabled-channels: Channels which can not be used + +Example: + + dma: dma-controller@801C0000 { + compatible = "stericsson,db8500-dma40", "stericsson,dma40"; + reg = <0x801C0000 0x1000 0x40010000 0x800>; + reg-names = "base", "lcpa"; + interrupt-parent = <&intc>; + interrupts = <0 25 0x4>; + + #dma-cells = <2>; + memcpy-channels = <56 57 58 59 60>; + disabled-channels = <12>; + dma-channels = <8>; + }; + +Clients +Required properties: +- dmas: Comma separated list of dma channel requests +- dma-names: Names of the aforementioned requested channels + +Each dmas request consists of 4 cells: + 1. A phandle pointing to the DMA controller + 2. Device Type + 3. The DMA request line number (only when 'use fixed channel' is set) + 4. A 32bit mask specifying; mode, direction and endianess [NB: This list will grow] + 0x00000001: Mode: + Logical channel when unset + Physical channel when set + 0x00000002: Direction: + Memory to Device when unset + Device to Memory when set + 0x00000004: Endianess: + Little endian when unset + Big endian when set + 0x00000008: Use fixed channel: + Use automatic channel selection when unset + Use DMA request line number when set + +Example: + + uart@80120000 { + compatible = "arm,pl011", "arm,primecell"; + reg = <0x80120000 0x1000>; + interrupts = <0 11 0x4>; + + dmas = <&dma 13 0 0x2>, /* Logical - DevToMem */ + <&dma 13 0 0x0>; /* Logical - MemToDev */ + dma-names = "rx", "rx"; + + status = "disabled"; + }; diff --git a/Documentation/devicetree/bindings/gpio/gpio-samsung.txt b/Documentation/devicetree/bindings/gpio/gpio-samsung.txt index f1e5dfecf55d..5375625e8cd2 100644 --- a/Documentation/devicetree/bindings/gpio/gpio-samsung.txt +++ b/Documentation/devicetree/bindings/gpio/gpio-samsung.txt @@ -39,46 +39,3 @@ Example: #gpio-cells = <4>; gpio-controller; }; - - -Samsung S3C24XX GPIO Controller - -Required properties: -- compatible: Compatible property value should be "samsung,s3c24xx-gpio". - -- reg: Physical base address of the controller and length of memory mapped - region. - -- #gpio-cells: Should be 3. The syntax of the gpio specifier used by client nodes - should be the following with values derived from the SoC user manual. - <[phandle of the gpio controller node] - [pin number within the gpio controller] - [mux function] - [flags and pull up/down] - - Values for gpio specifier: - - Pin number: depending on the controller a number from 0 up to 15. - - Mux function: Depending on the SoC and the gpio bank the gpio can be set - as input, output or a special function - - Flags and Pull Up/Down: the values to use differ for the individual SoCs - example S3C2416/S3C2450: - 0 - Pull Up/Down Disabled. - 1 - Pull Down Enabled. - 2 - Pull Up Enabled. - Bit 16 (0x00010000) - Input is active low. - Consult the user manual for the correct values of Mux and Pull Up/Down. - -- gpio-controller: Specifies that the node is a gpio controller. -- #address-cells: should be 1. -- #size-cells: should be 1. - -Example: - - gpa: gpio-controller@56000000 { - #address-cells = <1>; - #size-cells = <1>; - compatible = "samsung,s3c24xx-gpio"; - reg = <0x56000000 0x10>; - #gpio-cells = <3>; - gpio-controller; - }; diff --git a/Documentation/devicetree/bindings/gpio/renesas,gpio-rcar.txt b/Documentation/devicetree/bindings/gpio/renesas,gpio-rcar.txt new file mode 100644 index 000000000000..cb3dc7bcd8e6 --- /dev/null +++ b/Documentation/devicetree/bindings/gpio/renesas,gpio-rcar.txt @@ -0,0 +1,46 @@ +* Renesas R-Car GPIO Controller + +Required Properties: + + - compatible: should be one of the following. + - "renesas,gpio-r8a7778": for R8A7778 (R-Mobile M1) compatible GPIO controller. + - "renesas,gpio-r8a7779": for R8A7779 (R-Car H1) compatible GPIO controller. + - "renesas,gpio-r8a7790": for R8A7790 (R-Car H2) compatible GPIO controller. + - "renesas,gpio-rcar": for generic R-Car GPIO controller. + + - reg: Base address and length of each memory resource used by the GPIO + controller hardware module. + + - interrupt-parent: phandle of the parent interrupt controller. + - interrupts: Interrupt specifier for the controllers interrupt. + + - gpio-controller: Marks the device node as a gpio controller. + - #gpio-cells: Should be 2. The first cell is the GPIO number and the second + cell specifies GPIO flags, as defined in <dt-bindings/gpio/gpio.h>. Only the + GPIO_ACTIVE_HIGH and GPIO_ACTIVE_LOW flags are supported. + - gpio-ranges: Range of pins managed by the GPIO controller. + +Please refer to gpio.txt in this directory for details of gpio-ranges property +and the common GPIO bindings used by client devices. + +Example: R8A7779 (R-Car H1) GPIO controller nodes + + gpio0: gpio@ffc40000 { + compatible = "renesas,gpio-r8a7779", "renesas,gpio-rcar"; + reg = <0xffc40000 0x2c>; + interrupt-parent = <&gic>; + interrupts = <0 141 0x4>; + #gpio-cells = <2>; + gpio-controller; + gpio-ranges = <&pfc 0 0 32>; + }; + ... + gpio6: gpio@ffc46000 { + compatible = "renesas,gpio-r8a7779", "renesas,gpio-rcar"; + reg = <0xffc46000 0x2c>; + interrupt-parent = <&gic>; + interrupts = <0 147 0x4>; + #gpio-cells = <2>; + gpio-controller; + gpio-ranges = <&pfc 0 192 9>; + }; diff --git a/Documentation/devicetree/bindings/mtd/gpmc-nand.txt b/Documentation/devicetree/bindings/mtd/gpmc-nand.txt index 6a983c1d87cd..df338cb5059c 100644 --- a/Documentation/devicetree/bindings/mtd/gpmc-nand.txt +++ b/Documentation/devicetree/bindings/mtd/gpmc-nand.txt @@ -29,6 +29,13 @@ Optional properties: "bch4" 4-bit BCH ecc code "bch8" 8-bit BCH ecc code + - ti,nand-xfer-type: A string setting the data transfer type. One of: + + "prefetch-polled" Prefetch polled mode (default) + "polled" Polled mode, without prefetch + "prefetch-dma" Prefetch enabled sDMA mode + "prefetch-irq" Prefetch enabled irq mode + - elm_id: Specifies elm device node. This is required to support BCH error correction using ELM module. @@ -55,6 +62,7 @@ Example for an AM33xx board: reg = <0 0 0>; /* CS0, offset 0 */ nand-bus-width = <16>; ti,nand-ecc-opt = "bch8"; + ti,nand-xfer-type = "polled"; gpmc,sync-clk-ps = <0>; gpmc,cs-on-ns = <0>; diff --git a/Documentation/devicetree/bindings/pinctrl/samsung-pinctrl.txt b/Documentation/devicetree/bindings/pinctrl/samsung-pinctrl.txt index e15cfc4bb39e..72e9cd1e89b7 100644 --- a/Documentation/devicetree/bindings/pinctrl/samsung-pinctrl.txt +++ b/Documentation/devicetree/bindings/pinctrl/samsung-pinctrl.txt @@ -7,6 +7,10 @@ on-chip controllers onto these pads. Required Properties: - compatible: should be one of the following. + - "samsung,s3c2412-pinctrl": for S3C2412-compatible pin-controller, + - "samsung,s3c2416-pinctrl": for S3C2416-compatible pin-controller, + - "samsung,s3c2440-pinctrl": for S3C2440-compatible pin-controller, + - "samsung,s3c2450-pinctrl": for S3C2450-compatible pin-controller, - "samsung,s3c64xx-pinctrl": for S3C64xx-compatible pin-controller, - "samsung,exynos4210-pinctrl": for Exynos4210 compatible pin-controller. - "samsung,exynos4x12-pinctrl": for Exynos4x12 compatible pin-controller. @@ -116,6 +120,10 @@ B. External Wakeup Interrupts: For supporting external wakeup interrupts, a - compatible: identifies the type of the external wakeup interrupt controller The possible values are: + - samsung,s3c2410-wakeup-eint: represents wakeup interrupt controller + found on Samsung S3C24xx SoCs except S3C2412 and S3C2413, + - samsung,s3c2412-wakeup-eint: represents wakeup interrupt controller + found on Samsung S3C2412 and S3C2413 SoCs, - samsung,s3c64xx-wakeup-eint: represents wakeup interrupt controller found on Samsung S3C64xx SoCs, - samsung,exynos4210-wakeup-eint: represents wakeup interrupt controller diff --git a/Documentation/devicetree/bindings/sound/samsung-i2s.txt b/Documentation/devicetree/bindings/sound/samsung-i2s.txt index 3070046da2e5..025e66b85a43 100644 --- a/Documentation/devicetree/bindings/sound/samsung-i2s.txt +++ b/Documentation/devicetree/bindings/sound/samsung-i2s.txt @@ -8,6 +8,16 @@ Required SoC Specific Properties: - dmas: list of DMA controller phandle and DMA request line ordered pairs. - dma-names: identifier string for each DMA request line in the dmas property. These strings correspond 1:1 with the ordered pairs in dmas. +- clocks: Handle to iis clock and RCLK source clk. +- clock-names: + i2s0 uses some base clks from CMU and some are from audio subsystem internal + clock controller. The clock names for i2s0 should be "iis", "i2s_opclk0" and + "i2s_opclk1" as shown in the example below. + i2s1 and i2s2 uses clocks from CMU. The clock names for i2s1 and i2s2 should + be "iis" and "i2s_opclk0". + "iis" is the i2s bus clock and i2s_opclk0, i2s_opclk1 are sources of the root + clk. i2s0 has internal mux to select the source of root clk and i2s1 and i2s2 + doesn't have any such mux. Optional SoC Specific Properties: @@ -20,44 +30,26 @@ Optional SoC Specific Properties: then this flag is enabled. - samsung,idma-addr: Internal DMA register base address of the audio sub system(used in secondary sound source). - -Required Board Specific Properties: - -- gpios: The gpio specifier for data out,data in, LRCLK, CDCLK and SCLK - interface lines. The format of the gpio specifier depends on the gpio - controller. - The syntax of samsung gpio specifier is - <[phandle of the gpio controller node] - [pin number within the gpio controller] - [mux function] - [flags and pull up/down] - [drive strength]> +- pinctrl-0: Should specify pin control groups used for this controller. +- pinctrl-names: Should contain only one value - "default". Example: -- SoC Specific Portion: - -i2s@03830000 { +i2s0: i2s@03830000 { compatible = "samsung,i2s-v5"; reg = <0x03830000 0x100>; dmas = <&pdma0 10 &pdma0 9 &pdma0 8>; dma-names = "tx", "rx", "tx-sec"; + clocks = <&clock_audss EXYNOS_I2S_BUS>, + <&clock_audss EXYNOS_I2S_BUS>, + <&clock_audss EXYNOS_SCLK_I2S>; + clock-names = "iis", "i2s_opclk0", "i2s_opclk1"; samsung,supports-6ch; samsung,supports-rstclr; samsung,supports-secdai; samsung,idma-addr = <0x03000000>; -}; - -- Board Specific Portion: - -i2s@03830000 { - gpios = <&gpz 0 2 0 0>, /* I2S_0_SCLK */ - <&gpz 1 2 0 0>, /* I2S_0_CDCLK */ - <&gpz 2 2 0 0>, /* I2S_0_LRCK */ - <&gpz 3 2 0 0>, /* I2S_0_SDI */ - <&gpz 4 2 0 0>, /* I2S_0_SDO[1] */ - <&gpz 5 2 0 0>, /* I2S_0_SDO[2] */ - <&gpz 6 2 0 0>; /* I2S_0_SDO[3] */ + pinctrl-names = "default"; + pinctrl-0 = <&i2s0_bus>; }; diff --git a/Documentation/devicetree/bindings/usb/atmel-usb.txt b/Documentation/devicetree/bindings/usb/atmel-usb.txt index 60bd2150a3e6..55f51af08bc7 100644 --- a/Documentation/devicetree/bindings/usb/atmel-usb.txt +++ b/Documentation/devicetree/bindings/usb/atmel-usb.txt @@ -47,3 +47,85 @@ usb1: gadget@fffa4000 { interrupts = <10 4>; atmel,vbus-gpio = <&pioC 5 0>; }; + +Atmel High-Speed USB device controller + +Required properties: + - compatible: Should be "atmel,at91sam9rl-udc" + - reg: Address and length of the register set for the device + - interrupts: Should contain usba interrupt + - ep childnode: To specify the number of endpoints and their properties. + +Optional properties: + - atmel,vbus-gpio: If present, specifies a gpio that needs to be + activated for the bus to be powered. + +Required child node properties: + - name: Name of the endpoint. + - reg: Num of the endpoint. + - atmel,fifo-size: Size of the fifo. + - atmel,nb-banks: Number of banks. + - atmel,can-dma: Boolean to specify if the endpoint support DMA. + - atmel,can-isoc: Boolean to specify if the endpoint support ISOC. + +usb2: gadget@fff78000 { + #address-cells = <1>; + #size-cells = <0>; + compatible = "atmel,at91sam9rl-udc"; + reg = <0x00600000 0x80000 + 0xfff78000 0x400>; + interrupts = <27 4 0>; + atmel,vbus-gpio = <&pioB 19 0>; + + ep0 { + reg = <0>; + atmel,fifo-size = <64>; + atmel,nb-banks = <1>; + }; + + ep1 { + reg = <1>; + atmel,fifo-size = <1024>; + atmel,nb-banks = <2>; + atmel,can-dma; + atmel,can-isoc; + }; + + ep2 { + reg = <2>; + atmel,fifo-size = <1024>; + atmel,nb-banks = <2>; + atmel,can-dma; + atmel,can-isoc; + }; + + ep3 { + reg = <3>; + atmel,fifo-size = <1024>; + atmel,nb-banks = <3>; + atmel,can-dma; + }; + + ep4 { + reg = <4>; + atmel,fifo-size = <1024>; + atmel,nb-banks = <3>; + atmel,can-dma; + }; + + ep5 { + reg = <5>; + atmel,fifo-size = <1024>; + atmel,nb-banks = <3>; + atmel,can-dma; + atmel,can-isoc; + }; + + ep6 { + reg = <6>; + atmel,fifo-size = <1024>; + atmel,nb-banks = <3>; + atmel,can-dma; + atmel,can-isoc; + }; +}; diff --git a/Documentation/devicetree/bindings/usb/ux500-usb.txt b/Documentation/devicetree/bindings/usb/ux500-usb.txt new file mode 100644 index 000000000000..330d6ec15401 --- /dev/null +++ b/Documentation/devicetree/bindings/usb/ux500-usb.txt @@ -0,0 +1,50 @@ +Ux500 MUSB + +Required properties: + - compatible : Should be "stericsson,db8500-musb" + - reg : Offset and length of registers + - interrupts : Interrupt; mode, number and trigger + - dr_mode : Dual-role; either host mode "host", peripheral mode "peripheral" + or both "otg" + +Optional properties: + - dmas : A list of dma channels; + dma-controller, event-line, fixed-channel, flags + - dma-names : An ordered list of channel names affiliated to the above + +Example: + +usb_per5@a03e0000 { + compatible = "stericsson,db8500-musb", "mentor,musb"; + reg = <0xa03e0000 0x10000>; + interrupts = <0 23 0x4>; + interrupt-names = "mc"; + + dr_mode = "otg"; + + dmas = <&dma 38 0 0x2>, /* Logical - DevToMem */ + <&dma 38 0 0x0>, /* Logical - MemToDev */ + <&dma 37 0 0x2>, /* Logical - DevToMem */ + <&dma 37 0 0x0>, /* Logical - MemToDev */ + <&dma 36 0 0x2>, /* Logical - DevToMem */ + <&dma 36 0 0x0>, /* Logical - MemToDev */ + <&dma 19 0 0x2>, /* Logical - DevToMem */ + <&dma 19 0 0x0>, /* Logical - MemToDev */ + <&dma 18 0 0x2>, /* Logical - DevToMem */ + <&dma 18 0 0x0>, /* Logical - MemToDev */ + <&dma 17 0 0x2>, /* Logical - DevToMem */ + <&dma 17 0 0x0>, /* Logical - MemToDev */ + <&dma 16 0 0x2>, /* Logical - DevToMem */ + <&dma 16 0 0x0>, /* Logical - MemToDev */ + <&dma 39 0 0x2>, /* Logical - DevToMem */ + <&dma 39 0 0x0>; /* Logical - MemToDev */ + + dma-names = "iep_1_9", "oep_1_9", + "iep_2_10", "oep_2_10", + "iep_3_11", "oep_3_11", + "iep_4_12", "oep_4_12", + "iep_5_13", "oep_5_13", + "iep_6_14", "oep_6_14", + "iep_7_15", "oep_7_15", + "iep_8", "oep_8"; +}; |