mmc: sd: add support for signal voltage switch procedure

Host Controller v3.00 adds another Capabilities register. Apart
from other things, this new register indicates whether the Host
Controller supports SDR50, SDR104, and DDR50 UHS-I modes. The spec
doesn't mention about explicit support for SDR12 and SDR25 UHS-I
modes, so the Host Controller v3.00 should support them by default.
Also if the controller supports SDR104 mode, it will also support
SDR50 mode as well. So depending on the host support, we set the
corresponding MMC_CAP_* flags. One more new register. Host Control2
is added in v3.00, which is used during Signal Voltage Switch
procedure described below.

Since as per v3.00 spec, UHS-I supported hosts should set S18R
to 1, we set S18R (bit 24) of OCR before sending ACMD41. We also
need to set XPC (bit 28) of OCR in case the host can supply >150mA.
This support is indicated by the Maximum Current Capabilities
register of the Host Controller.

If the response of ACMD41 has both CCS and S18A set, we start the
signal voltage switch procedure, which if successfull, will switch
the card from 3.3V signalling to 1.8V signalling. Signal voltage
switch procedure adds support for a new command CMD11 in the
Physical Layer Spec v3.01. As part of this procedure, we need to
set 1.8V Signalling Enable (bit 3) of Host Control2 register, which
if remains set after 5ms, means the switch to 1.8V signalling is
successfull. Otherwise, we clear bit 24 of OCR and retry the
initialization sequence. When we remove the card, and insert the
same or another card, we need to make sure that we start with 3.3V
signalling voltage. So we call mmc_set_signal_voltage() with
MMC_SIGNAL_VOLTAGE_330 set so that we are back to 3.3V signalling
voltage before we actually start initializing the card.

Tested by Zhangfei Gao with a Toshiba uhs card and general hs card,
on mmp2 in SDMA mode.

Signed-off-by: Arindam Nath <arindam.nath@amd.com>
Reviewed-by: Philip Rakity <prakity@marvell.com>
Tested-by: Philip Rakity <prakity@marvell.com>
Acked-by: Zhangfei Gao <zhangfei.gao@marvell.com>
Signed-off-by: Chris Ball <cjb@laptop.org>

3 files changed, 67 insertions, 2 deletions

diff --git a/drivers/mmc/core/core.c b/drivers/mmc/core/core.c
index 1dbc18576219..5005a6323165 100644
--- a/drivers/mmc/core/core.c
+++ b/drivers/mmc/core/core.c
@@ -942,6 +942,38 @@ u32 mmc_select_voltage(struct mmc_host *host, u32 ocr)
 	return ocr;
 }
 
+int mmc_set_signal_voltage(struct mmc_host *host, int signal_voltage)
+{
+	struct mmc_command cmd = {0};
+	int err = 0;
+
+	BUG_ON(!host);
+
+	/*
+	 * Send CMD11 only if the request is to switch the card to
+	 * 1.8V signalling.
+	 */
+	if (signal_voltage == MMC_SIGNAL_VOLTAGE_180) {
+		cmd.opcode = SD_SWITCH_VOLTAGE;
+		cmd.arg = 0;
+		cmd.flags = MMC_RSP_R1 | MMC_CMD_AC;
+
+		err = mmc_wait_for_cmd(host, &cmd, 0);
+		if (err)
+			return err;
+
+		if (!mmc_host_is_spi(host) && (cmd.resp[0] & R1_ERROR))
+			return -EIO;
+	}
+
+	host->ios.signal_voltage = signal_voltage;
+
+	if (host->ops->start_signal_voltage_switch)
+		err = host->ops->start_signal_voltage_switch(host, &host->ios);
+
+	return err;
+}
+
 /*
  * Select timing parameters for host.
  */
diff --git a/drivers/mmc/core/core.h b/drivers/mmc/core/core.h
index ca1fdde29df6..7745dea430b8 100644
--- a/drivers/mmc/core/core.h
+++ b/drivers/mmc/core/core.h
@@ -41,6 +41,7 @@ void mmc_set_bus_width(struct mmc_host *host, unsigned int width);
 void mmc_set_bus_width_ddr(struct mmc_host *host, unsigned int width,
 			   unsigned int ddr);
 u32 mmc_select_voltage(struct mmc_host *host, u32 ocr);
+int mmc_set_signal_voltage(struct mmc_host *host, int signal_voltage);
 void mmc_set_timing(struct mmc_host *host, unsigned int timing);
 
 static inline void mmc_delay(unsigned int ms)
diff --git a/drivers/mmc/core/sd.c b/drivers/mmc/core/sd.c
index 6dac89fe0535..b0cd285d272a 100644
--- a/drivers/mmc/core/sd.c
+++ b/drivers/mmc/core/sd.c
@@ -403,6 +403,7 @@ struct device_type sd_type = {
 int mmc_sd_get_cid(struct mmc_host *host, u32 ocr, u32 *cid)
 {
 	int err;
+	u32 rocr;
 
 	/*
 	 * Since we're changing the OCR value, we seem to
@@ -420,12 +421,38 @@ int mmc_sd_get_cid(struct mmc_host *host, u32 ocr, u32 *cid)
 	 */
 	err = mmc_send_if_cond(host, ocr);
 	if (!err)
-		ocr |= 1 << 30;
+		ocr |= SD_OCR_CCS;
 
-	err = mmc_send_app_op_cond(host, ocr, NULL);
+	/*
+	 * If the host supports one of UHS-I modes, request the card
+	 * to switch to 1.8V signaling level.
+	 */
+	if (host->caps & (MMC_CAP_UHS_SDR12 | MMC_CAP_UHS_SDR25 |
+	    MMC_CAP_UHS_SDR50 | MMC_CAP_UHS_SDR104 | MMC_CAP_UHS_DDR50))
+		ocr |= SD_OCR_S18R;
+
+	/* If the host can supply more than 150mA, XPC should be set to 1. */
+	if (host->caps & (MMC_CAP_SET_XPC_330 | MMC_CAP_SET_XPC_300 |
+	    MMC_CAP_SET_XPC_180))
+		ocr |= SD_OCR_XPC;
+
+try_again:
+	err = mmc_send_app_op_cond(host, ocr, &rocr);
 	if (err)
 		return err;
 
+	/*
+	 * In case CCS and S18A in the response is set, start Signal Voltage
+	 * Switch procedure. SPI mode doesn't support CMD11.
+	 */
+	if (!mmc_host_is_spi(host) && ((rocr & 0x41000000) == 0x41000000)) {
+		err = mmc_set_signal_voltage(host, MMC_SIGNAL_VOLTAGE_180);
+		if (err) {
+			ocr &= ~SD_OCR_S18R;
+			goto try_again;
+		}
+	}
+
 	if (mmc_host_is_spi(host))
 		err = mmc_send_cid(host, cid);
 	else
@@ -773,6 +800,11 @@ int mmc_attach_sd(struct mmc_host *host)
 	BUG_ON(!host);
 	WARN_ON(!host->claimed);
 
+	/* Make sure we are at 3.3V signalling voltage */
+	err = mmc_set_signal_voltage(host, MMC_SIGNAL_VOLTAGE_330);
+	if (err)
+		return err;
+
 	err = mmc_send_app_op_cond(host, 0, &ocr);
 	if (err)
 		return err;