[PATCH] Typo fix: dot after newline in printk strings

Typo fix: dots appearing after a newline in printk strings.

Signed-off-by: Jean Delvare <khali@linux-fr.org>
Signed-off-by: Andrew Morton <akpm@osdl.org>
Signed-off-by: Linus Torvalds <torvalds@osdl.org>

7 files changed, 7 insertions, 7 deletions

diff --git a/drivers/char/ser_a2232.c b/drivers/char/ser_a2232.c
index 6b4e9d155f50..dda30e42ec79 100644
--- a/drivers/char/ser_a2232.c
+++ b/drivers/char/ser_a2232.c
@@ -790,7 +790,7 @@ static int __init a2232board_init(void)
 
 	}	
 
-	printk("Total: %d A2232 boards initialized.\n.", nr_a2232); /* Some status report if no card was found */
+	printk("Total: %d A2232 boards initialized.\n", nr_a2232); /* Some status report if no card was found */
 
 	a2232_init_portstructs();
 
diff --git a/drivers/message/i2o/debug.c b/drivers/message/i2o/debug.c
index 018ca887ca85..40d4ea898dbc 100644
--- a/drivers/message/i2o/debug.c
+++ b/drivers/message/i2o/debug.c
@@ -90,7 +90,7 @@ static void i2o_report_fail_status(u8 req_status, u32 * msg)
 	};
 
 	if (req_status == I2O_FSC_TRANSPORT_UNKNOWN_FAILURE)
-		printk(KERN_DEBUG "TRANSPORT_UNKNOWN_FAILURE (%0#2x)\n.",
+		printk(KERN_DEBUG "TRANSPORT_UNKNOWN_FAILURE (%0#2x).\n",
 		       req_status);
 	else
 		printk(KERN_DEBUG "TRANSPORT_%s.\n",
diff --git a/drivers/net/wireless/prism54/islpci_mgt.c b/drivers/net/wireless/prism54/islpci_mgt.c
index 4937a5ad4b2c..6a60c5970cb5 100644
--- a/drivers/net/wireless/prism54/islpci_mgt.c
+++ b/drivers/net/wireless/prism54/islpci_mgt.c
@@ -137,7 +137,7 @@ islpci_mgmt_rx_fill(struct net_device *ndev)
 						       PCI_DMA_FROMDEVICE);
 			if (!buf->pci_addr) {
 				printk(KERN_WARNING
-				       "Failed to make memory DMA'able\n.");
+				       "Failed to make memory DMA'able.\n");
 				return -ENOMEM;
 			}
 		}
diff --git a/drivers/pci/hotplug/ibmphp_core.c b/drivers/pci/hotplug/ibmphp_core.c
index 0392e004258f..aabf1e70b528 100644
--- a/drivers/pci/hotplug/ibmphp_core.c
+++ b/drivers/pci/hotplug/ibmphp_core.c
@@ -1077,7 +1077,7 @@ static int enable_slot(struct hotplug_slot *hs)
 	if (rc) {
 		err("Adding this card exceeds the limitations of this bus.\n");
 		err("(i.e., >1 133MHz cards running on same bus, or "
-		     ">2 66 PCI cards running on same bus\n.");
+		     ">2 66 PCI cards running on same bus.\n");
 		err("Try hot-adding into another bus\n");
 		rc = -EINVAL;
 		goto error_nopower;
diff --git a/drivers/usb/input/pid.c b/drivers/usb/input/pid.c
index a00672c96644..dca5ee93a4ef 100644
--- a/drivers/usb/input/pid.c
+++ b/drivers/usb/input/pid.c
@@ -198,7 +198,7 @@ static int hid_pid_upload_effect(struct input_dev *dev,
 		}
 
 		effect->id = id;
-		dev_dbg(&pid_private->hid->dev->dev, "effect ID is %d\n.", id);
+		dev_dbg(&pid_private->hid->dev->dev, "effect ID is %d.\n", id);
 		pid_private->effects[id].owner = current->pid;
 		pid_private->effects[id].flags = (1 << FF_PID_FLAGS_USED);
 		spin_unlock_irqrestore(&pid_private->lock, flags);
diff --git a/net/ipv4/netfilter/ipt_addrtype.c b/net/ipv4/netfilter/ipt_addrtype.c
index f5909a4c3fc7..e19c2a52d00c 100644
--- a/net/ipv4/netfilter/ipt_addrtype.c
+++ b/net/ipv4/netfilter/ipt_addrtype.c
@@ -48,7 +48,7 @@ static int checkentry(const char *tablename, const struct ipt_ip *ip,
 		      unsigned int hook_mask)
 {
 	if (matchsize != IPT_ALIGN(sizeof(struct ipt_addrtype_info))) {
-		printk(KERN_ERR "ipt_addrtype: invalid size (%u != %Zu)\n.",
+		printk(KERN_ERR "ipt_addrtype: invalid size (%u != %Zu)\n",
 		       matchsize, IPT_ALIGN(sizeof(struct ipt_addrtype_info)));
 		return 0;
 	}
diff --git a/sound/oss/awe_wave.c b/sound/oss/awe_wave.c
index d2b9beda8ace..b3ea719d33db 100644
--- a/sound/oss/awe_wave.c
+++ b/sound/oss/awe_wave.c
@@ -6062,7 +6062,7 @@ static int awe_pnp_probe(struct pnp_dev *dev, const struct pnp_device_id *dev_id
 	io1 = pnp_port_start(dev,0);
 	io2 = pnp_port_start(dev,1);
 	io3 = pnp_port_start(dev,2);
-	printk(KERN_INFO "AWE32: A PnP Wave Table was detected at IO's %#x,%#x,%#x\n.",
+	printk(KERN_INFO "AWE32: A PnP Wave Table was detected at IO's %#x,%#x,%#x.\n",
 	       io1, io2, io3);
 	setup_ports(io1, io2, io3);