diff options
-rw-r--r-- | Makefile | 2 | ||||
-rw-r--r-- | hw/i2c.h | 4 | ||||
-rw-r--r-- | hw/lm832x.c | 535 | ||||
-rw-r--r-- | hw/nseries.c | 126 |
4 files changed, 658 insertions, 9 deletions
@@ -52,7 +52,7 @@ OBJS+=block.o OBJS+=irq.o OBJS+=i2c.o smbus.o smbus_eeprom.o max7310.o max111x.o wm8750.o OBJS+=ssd0303.o ssd0323.o ads7846.o stellaris_input.o twl92230.o -OBJS+=tmp105.o +OBJS+=tmp105.o lm832x.o OBJS+=scsi-disk.o cdrom.o OBJS+=scsi-generic.o OBJS+=usb.o usb-hub.o usb-linux.o usb-hid.o usb-msd.o usb-wacom.o usb-serial.o @@ -84,4 +84,8 @@ struct i2c_slave *tmp105_init(i2c_bus *bus, qemu_irq alarm); void tmp105_reset(i2c_slave *i2c); void tmp105_set(i2c_slave *i2c, int temp); +/* lm832x.c */ +struct i2c_slave *lm8323_init(i2c_bus *bus, qemu_irq nirq); +void lm832x_key_event(struct i2c_slave *i2c, int key, int state); + #endif diff --git a/hw/lm832x.c b/hw/lm832x.c new file mode 100644 index 0000000000..efb80f7e7f --- /dev/null +++ b/hw/lm832x.c @@ -0,0 +1,535 @@ +/* + * National Semiconductor LM8322/8323 GPIO keyboard & PWM chips. + * + * Copyright (C) 2008 Nokia Corporation + * Written by Andrzej Zaborowski <andrew@openedhand.com> + * + * This program is free software; you can redistribute it and/or + * modify it under the terms of the GNU General Public License as + * published by the Free Software Foundation; either version 2 or + * (at your option) version 3 of the License. + * + * This program is distributed in the hope that it will be useful, + * but WITHOUT ANY WARRANTY; without even the implied warranty of + * MERCHANTABILITY or FITNESS FOR A PARTICULAR PURPOSE. See the + * GNU General Public License for more details. + * + * You should have received a copy of the GNU General Public License + * along with this program; if not, write to the Free Software + * Foundation, Inc., 59 Temple Place, Suite 330, Boston, + * MA 02111-1307 USA + */ + +#include "hw.h" +#include "i2c.h" +#include "qemu-timer.h" +#include "console.h" + +struct lm_kbd_s { + i2c_slave i2c; + int i2c_dir; + int i2c_cycle; + int reg; + + qemu_irq nirq; + uint16_t model; + + struct { + qemu_irq out[2]; + int in[2][2]; + } mux; + + uint8_t config; + uint8_t status; + uint8_t acttime; + uint8_t error; + uint8_t clock; + + struct { + uint16_t pull; + uint16_t mask; + uint16_t dir; + uint16_t level; + qemu_irq out[16]; + } gpio; + + struct { + uint8_t dbnctime; + uint8_t size; + int start; + int len; + uint8_t fifo[16]; + } kbd; + + struct { + uint16_t file[256]; + uint8_t faddr; + uint8_t addr[3]; + QEMUTimer *tm[3]; + } pwm; +}; + +#define INT_KEYPAD (1 << 0) +#define INT_ERROR (1 << 3) +#define INT_NOINIT (1 << 4) +#define INT_PWMEND(n) (1 << (5 + n)) + +#define ERR_BADPAR (1 << 0) +#define ERR_CMDUNK (1 << 1) +#define ERR_KEYOVR (1 << 2) +#define ERR_FIFOOVR (1 << 6) + +static void lm_kbd_irq_update(struct lm_kbd_s *s) +{ + qemu_set_irq(s->nirq, !s->status); +} + +static void lm_kbd_gpio_update(struct lm_kbd_s *s) +{ +} + +static void lm_kbd_reset(struct lm_kbd_s *s) +{ + s->config = 0x80; + s->status = INT_NOINIT; + s->acttime = 125; + s->kbd.dbnctime = 3; + s->kbd.size = 0x33; + s->clock = 0x08; + + lm_kbd_irq_update(s); + lm_kbd_gpio_update(s); +} + +static void lm_kbd_error(struct lm_kbd_s *s, int err) +{ + s->error |= err; + s->status |= INT_ERROR; + lm_kbd_irq_update(s); +} + +static void lm_kbd_pwm_tick(struct lm_kbd_s *s, int line) +{ +} + +static void lm_kbd_pwm_start(struct lm_kbd_s *s, int line) +{ + lm_kbd_pwm_tick(s, line); +} + +static void lm_kbd_pwm0_tick(void *opaque) +{ + lm_kbd_pwm_tick(opaque, 0); +} +static void lm_kbd_pwm1_tick(void *opaque) +{ + lm_kbd_pwm_tick(opaque, 1); +} +static void lm_kbd_pwm2_tick(void *opaque) +{ + lm_kbd_pwm_tick(opaque, 2); +} + +enum { + LM832x_CMD_READ_ID = 0x80, /* Read chip ID. */ + LM832x_CMD_WRITE_CFG = 0x81, /* Set configuration item. */ + LM832x_CMD_READ_INT = 0x82, /* Get interrupt status. */ + LM832x_CMD_RESET = 0x83, /* Reset, same as external one */ + LM823x_CMD_WRITE_PULL_DOWN = 0x84, /* Select GPIO pull-up/down. */ + LM832x_CMD_WRITE_PORT_SEL = 0x85, /* Select GPIO in/out. */ + LM832x_CMD_WRITE_PORT_STATE = 0x86, /* Set GPIO pull-up/down. */ + LM832x_CMD_READ_PORT_SEL = 0x87, /* Get GPIO in/out. */ + LM832x_CMD_READ_PORT_STATE = 0x88, /* Get GPIO pull-up/down. */ + LM832x_CMD_READ_FIFO = 0x89, /* Read byte from FIFO. */ + LM832x_CMD_RPT_READ_FIFO = 0x8a, /* Read FIFO (no increment). */ + LM832x_CMD_SET_ACTIVE = 0x8b, /* Set active time. */ + LM832x_CMD_READ_ERROR = 0x8c, /* Get error status. */ + LM832x_CMD_READ_ROTATOR = 0x8e, /* Read rotator status. */ + LM832x_CMD_SET_DEBOUNCE = 0x8f, /* Set debouncing time. */ + LM832x_CMD_SET_KEY_SIZE = 0x90, /* Set keypad size. */ + LM832x_CMD_READ_KEY_SIZE = 0x91, /* Get keypad size. */ + LM832x_CMD_READ_CFG = 0x92, /* Get configuration item. */ + LM832x_CMD_WRITE_CLOCK = 0x93, /* Set clock config. */ + LM832x_CMD_READ_CLOCK = 0x94, /* Get clock config. */ + LM832x_CMD_PWM_WRITE = 0x95, /* Write PWM script. */ + LM832x_CMD_PWM_START = 0x96, /* Start PWM engine. */ + LM832x_CMD_PWM_STOP = 0x97, /* Stop PWM engine. */ +}; + +#define LM832x_MAX_KPX 8 +#define LM832x_MAX_KPY 12 + +static uint8_t lm_kbd_read(struct lm_kbd_s *s, int reg, int byte) +{ + int ret; + + switch (reg) { + case LM832x_CMD_READ_ID: + ret = 0x0400; + break; + + case LM832x_CMD_READ_INT: + ret = s->status; + if (!(s->status & INT_NOINIT)) { + s->status = 0; + lm_kbd_irq_update(s); + } + break; + + case LM832x_CMD_READ_PORT_SEL: + ret = s->gpio.dir; + break; + case LM832x_CMD_READ_PORT_STATE: + ret = s->gpio.mask; + break; + + case LM832x_CMD_READ_FIFO: + if (s->kbd.len <= 1) + return 0x00; + + /* Example response from the two commands after a INT_KEYPAD + * interrupt caused by the key 0x3c being pressed: + * RPT_READ_FIFO: 55 bc 00 4e ff 0a 50 08 00 29 d9 08 01 c9 01 + * READ_FIFO: bc 00 00 4e ff 0a 50 08 00 29 d9 08 01 c9 01 + * RPT_READ_FIFO: bc 00 00 4e ff 0a 50 08 00 29 d9 08 01 c9 01 + * + * 55 is the code of the key release event serviced in the previous + * interrupt handling. + * + * TODO: find out whether the FIFO is advanced a single character + * before reading every byte or the whole size of the FIFO at the + * last LM832x_CMD_READ_FIFO. This affects LM832x_CMD_RPT_READ_FIFO + * output in cases where there are more than one event in the FIFO. + * Assume 0xbc and 0x3c events are in the FIFO: + * RPT_READ_FIFO: 55 bc 3c 00 4e ff 0a 50 08 00 29 d9 08 01 c9 + * READ_FIFO: bc 3c 00 00 4e ff 0a 50 08 00 29 d9 08 01 c9 + * Does RPT_READ_FIFO now return 0xbc and 0x3c or only 0x3c? + */ + s->kbd.start ++; + s->kbd.start &= sizeof(s->kbd.fifo) - 1; + s->kbd.len --; + + return s->kbd.fifo[s->kbd.start]; + case LM832x_CMD_RPT_READ_FIFO: + if (byte >= s->kbd.len) + return 0x00; + + return s->kbd.fifo[(s->kbd.start + byte) & (sizeof(s->kbd.fifo) - 1)]; + + case LM832x_CMD_READ_ERROR: + return s->error; + + case LM832x_CMD_READ_ROTATOR: + return 0; + + case LM832x_CMD_READ_KEY_SIZE: + return s->kbd.size; + + case LM832x_CMD_READ_CFG: + return s->config & 0xf; + + case LM832x_CMD_READ_CLOCK: + return (s->clock & 0xfc) | 2; + + default: + lm_kbd_error(s, ERR_CMDUNK); + fprintf(stderr, "%s: unknown command %02x\n", __FUNCTION__, reg); + return 0x00; + } + + return ret >> (byte << 3); +} + +static void lm_kbd_write(struct lm_kbd_s *s, int reg, int byte, uint8_t value) +{ + switch (reg) { + case LM832x_CMD_WRITE_CFG: + s->config = value; + /* This must be done whenever s->mux.in is updated (never). */ + if ((s->config >> 1) & 1) /* MUX1EN */ + qemu_set_irq(s->mux.out[0], s->mux.in[0][(s->config >> 0) & 1]); + if ((s->config >> 3) & 1) /* MUX2EN */ + qemu_set_irq(s->mux.out[0], s->mux.in[0][(s->config >> 2) & 1]); + /* TODO: check that this is issued only following the chip reset + * and not in the middle of operation and that it is followed by + * the GPIO ports re-resablishing through WRITE_PORT_SEL and + * WRITE_PORT_STATE (using a timer perhaps) and otherwise output + * warnings. */ + s->status = 0; + lm_kbd_irq_update(s); + s->kbd.len = 0; + s->kbd.start = 0; + s->reg = -1; + break; + + case LM832x_CMD_RESET: + if (value == 0xaa) + lm_kbd_reset(s); + else + lm_kbd_error(s, ERR_BADPAR); + s->reg = -1; + break; + + case LM823x_CMD_WRITE_PULL_DOWN: + if (!byte) + s->gpio.pull = value; + else { + s->gpio.pull |= value << 8; + lm_kbd_gpio_update(s); + s->reg = -1; + } + break; + case LM832x_CMD_WRITE_PORT_SEL: + if (!byte) + s->gpio.dir = value; + else { + s->gpio.dir |= value << 8; + lm_kbd_gpio_update(s); + s->reg = -1; + } + break; + case LM832x_CMD_WRITE_PORT_STATE: + if (!byte) + s->gpio.mask = value; + else { + s->gpio.mask |= value << 8; + lm_kbd_gpio_update(s); + s->reg = -1; + } + break; + + case LM832x_CMD_SET_ACTIVE: + s->acttime = value; + s->reg = -1; + break; + + case LM832x_CMD_SET_DEBOUNCE: + s->kbd.dbnctime = value; + s->reg = -1; + if (!value) + lm_kbd_error(s, ERR_BADPAR); + break; + + case LM832x_CMD_SET_KEY_SIZE: + s->kbd.size = value; + s->reg = -1; + if ( + (value & 0xf) < 3 || (value & 0xf) > LM832x_MAX_KPY || + (value >> 4) < 3 || (value >> 4) > LM832x_MAX_KPX) + lm_kbd_error(s, ERR_BADPAR); + break; + + case LM832x_CMD_WRITE_CLOCK: + s->clock = value; + s->reg = -1; + if ((value & 3) && (value & 3) != 3) { + lm_kbd_error(s, ERR_BADPAR); + fprintf(stderr, "%s: invalid clock setting in RCPWM\n", + __FUNCTION__); + } + /* TODO: Validate that the command is only issued once */ + break; + + case LM832x_CMD_PWM_WRITE: + if (byte == 0) { + if (!(value & 3) || (value >> 2) > 59) { + lm_kbd_error(s, ERR_BADPAR); + s->reg = -1; + break; + } + + s->pwm.faddr = value; + s->pwm.file[s->pwm.faddr] = 0; + } else if (byte == 1) { + s->pwm.file[s->pwm.faddr] |= value << 8; + } else if (byte == 2) { + s->pwm.file[s->pwm.faddr] |= value << 0; + s->reg = -1; + } + break; + case LM832x_CMD_PWM_START: + s->reg = -1; + if (!(value & 3) || (value >> 2) > 59) { + lm_kbd_error(s, ERR_BADPAR); + break; + } + + s->pwm.addr[(value & 3) - 1] = value >> 2; + lm_kbd_pwm_start(s, (value & 3) - 1); + break; + case LM832x_CMD_PWM_STOP: + s->reg = -1; + if (!(value & 3)) { + lm_kbd_error(s, ERR_BADPAR); + break; + } + + qemu_del_timer(s->pwm.tm[(value & 3) - 1]); + break; + + case -1: + lm_kbd_error(s, ERR_BADPAR); + break; + default: + lm_kbd_error(s, ERR_CMDUNK); + fprintf(stderr, "%s: unknown command %02x\n", __FUNCTION__, reg); + break; + } +} + +static void lm_i2c_event(i2c_slave *i2c, enum i2c_event event) +{ + struct lm_kbd_s *s = (struct lm_kbd_s *) i2c; + + switch (event) { + case I2C_START_RECV: + case I2C_START_SEND: + s->i2c_cycle = 0; + s->i2c_dir = (event == I2C_START_SEND); + break; + + default: + break; + } +} + +static int lm_i2c_rx(i2c_slave *i2c) +{ + struct lm_kbd_s *s = (struct lm_kbd_s *) i2c; + + return lm_kbd_read(s, s->reg, s->i2c_cycle ++); +} + +static int lm_i2c_tx(i2c_slave *i2c, uint8_t data) +{ + struct lm_kbd_s *s = (struct lm_kbd_s *) i2c; + + if (!s->i2c_cycle) + s->reg = data; + else + lm_kbd_write(s, s->reg, s->i2c_cycle - 1, data); + s->i2c_cycle ++; + + return 0; +} + +static void lm_kbd_save(QEMUFile *f, void *opaque) +{ + struct lm_kbd_s *s = (struct lm_kbd_s *) opaque; + int i; + + i2c_slave_save(f, &s->i2c); + qemu_put_byte(f, s->i2c_dir); + qemu_put_byte(f, s->i2c_cycle); + qemu_put_byte(f, (uint8_t) s->reg); + + qemu_put_8s(f, &s->config); + qemu_put_8s(f, &s->status); + qemu_put_8s(f, &s->acttime); + qemu_put_8s(f, &s->error); + qemu_put_8s(f, &s->clock); + + qemu_put_be16s(f, &s->gpio.pull); + qemu_put_be16s(f, &s->gpio.mask); + qemu_put_be16s(f, &s->gpio.dir); + qemu_put_be16s(f, &s->gpio.level); + + qemu_put_byte(f, s->kbd.dbnctime); + qemu_put_byte(f, s->kbd.size); + qemu_put_byte(f, s->kbd.start); + qemu_put_byte(f, s->kbd.len); + qemu_put_buffer(f, s->kbd.fifo, sizeof(s->kbd.fifo)); + + for (i = 0; i < sizeof(s->pwm.file); i ++) + qemu_put_be16s(f, &s->pwm.file[i]); + qemu_put_8s(f, &s->pwm.faddr); + qemu_put_buffer(f, s->pwm.addr, sizeof(s->pwm.addr)); + qemu_put_timer(f, s->pwm.tm[0]); + qemu_put_timer(f, s->pwm.tm[1]); + qemu_put_timer(f, s->pwm.tm[2]); +} + +static int lm_kbd_load(QEMUFile *f, void *opaque, int version_id) +{ + struct lm_kbd_s *s = (struct lm_kbd_s *) opaque; + int i; + + i2c_slave_load(f, &s->i2c); + s->i2c_dir = qemu_get_byte(f); + s->i2c_cycle = qemu_get_byte(f); + s->reg = (int8_t) qemu_get_byte(f); + + qemu_get_8s(f, &s->config); + qemu_get_8s(f, &s->status); + qemu_get_8s(f, &s->acttime); + qemu_get_8s(f, &s->error); + qemu_get_8s(f, &s->clock); + + qemu_get_be16s(f, &s->gpio.pull); + qemu_get_be16s(f, &s->gpio.mask); + qemu_get_be16s(f, &s->gpio.dir); + qemu_get_be16s(f, &s->gpio.level); + + s->kbd.dbnctime = qemu_get_byte(f); + s->kbd.size = qemu_get_byte(f); + s->kbd.start = qemu_get_byte(f); + s->kbd.len = qemu_get_byte(f); + qemu_get_buffer(f, s->kbd.fifo, sizeof(s->kbd.fifo)); + + for (i = 0; i < sizeof(s->pwm.file); i ++) + qemu_get_be16s(f, &s->pwm.file[i]); + qemu_get_8s(f, &s->pwm.faddr); + qemu_get_buffer(f, s->pwm.addr, sizeof(s->pwm.addr)); + qemu_get_timer(f, s->pwm.tm[0]); + qemu_get_timer(f, s->pwm.tm[1]); + qemu_get_timer(f, s->pwm.tm[2]); + + lm_kbd_irq_update(s); + lm_kbd_gpio_update(s); + + return 0; +} + +static int lm_kbd_iid = 0; + +struct i2c_slave *lm8323_init(i2c_bus *bus, qemu_irq nirq) +{ + struct lm_kbd_s *s; + + s = (struct lm_kbd_s *) i2c_slave_init(bus, 0, sizeof(struct lm_kbd_s)); + s->model = 0x8323; + s->pwm.tm[0] = qemu_new_timer(vm_clock, lm_kbd_pwm0_tick, s); + s->pwm.tm[1] = qemu_new_timer(vm_clock, lm_kbd_pwm1_tick, s); + s->pwm.tm[2] = qemu_new_timer(vm_clock, lm_kbd_pwm2_tick, s); + s->nirq = nirq; + + s->i2c.event = lm_i2c_event; + s->i2c.recv = lm_i2c_rx; + s->i2c.send = lm_i2c_tx; + + lm_kbd_reset(s); + + qemu_register_reset((void *) lm_kbd_reset, s); + register_savevm("LM8323", lm_kbd_iid ++, 0, + lm_kbd_save, lm_kbd_load, s); + + return &s->i2c; +} + +void lm832x_key_event(struct i2c_slave *i2c, int key, int state) +{ + struct lm_kbd_s *s = (struct lm_kbd_s *) i2c; + + if ((s->status & INT_ERROR) && (s->error & ERR_FIFOOVR)) + return; + + if (s->kbd.len >= sizeof(s->kbd.fifo)) + return lm_kbd_error(s, ERR_FIFOOVR); + + s->kbd.fifo[(s->kbd.start + s->kbd.len ++) & (sizeof(s->kbd.fifo) - 1)] = + key | (state << 7); + + /* We never set ERR_KEYOVR because we support multiple keys fine. */ + s->status |= INT_KEYPAD; + lm_kbd_irq_update(s); +} diff --git a/hw/nseries.c b/hw/nseries.c index a3af41c193..937e72c899 100644 --- a/hw/nseries.c +++ b/hw/nseries.c @@ -45,6 +45,7 @@ struct n800_s { i2c_bus *i2c; int keymap[0x80]; + i2c_slave *kbd; struct tusb_s *usb; void *retu; @@ -92,16 +93,22 @@ struct n800_s { #define N8X0_TAHVO_GPIO 111 #define N800_UNKNOWN_GPIO4 112 /* out */ #define N810_SLEEPX_LED_GPIO 112 -#define N810_TSC_UNKNOWN_GPIO 118 /* out */ -#define N800_TSC_RESET_GPIO 119 /* ? */ +#define N800_TSC_RESET_GPIO 118 /* ? */ +#define N800_TSC_UNKNOWN_GPIO 119 /* out */ #define N8X0_TMP105_GPIO 125 /* Config */ #define XLDR_LL_UART 1 -/* Addresses on the I2C bus */ -#define N8X0_TMP105_ADDR 0x48 -#define N8X0_MENELAUS_ADDR 0x72 +/* Addresses on the I2C bus 0 */ +#define N810_TLV320AIC33_ADDR 0x18 /* Audio CODEC */ +#define N8X0_TCM825x_ADDR 0x29 /* Camera */ +#define N810_LP5521_ADDR 0x32 /* LEDs */ +#define N810_TSL2563_ADDR 0x3d /* Light sensor */ +#define N810_LM8323_ADDR 0x45 /* Keyboard */ +/* Addresses on the I2C bus 1 */ +#define N8X0_TMP105_ADDR 0x48 /* Temperature sensor */ +#define N8X0_MENELAUS_ADDR 0x72 /* Power management */ /* Chipselects on GPMC NOR interface */ #define N8X0_ONENAND_CS 0 @@ -190,12 +197,12 @@ static const int n800_keys[16] = { 28, /* Enter */ 77, /* Right */ -1, - 1, /* Cycle (ESC) */ + 1, /* Cycle (ESC) */ 80, /* Down */ 62, /* Menu (F4) */ -1, 66, /* Zoom- (F8) */ - 64, /* FS (F6) */ + 64, /* FullScreen (F6) */ 65, /* Zoom+ (F7) */ -1, }; @@ -235,6 +242,107 @@ static void n810_tsc_setup(struct n800_s *s) tsc2005_set_transform(s->ts.opaque, &n810_pointercal); } +/* N810 Keyboard controller */ +static void n810_key_event(void *opaque, int keycode) +{ + struct n800_s *s = (struct n800_s *) opaque; + int code = s->keymap[keycode & 0x7f]; + + if (code == -1) { + if ((keycode & 0x7f) == RETU_KEYCODE) + retu_key_event(s->retu, !(keycode & 0x80)); + return; + } + + lm832x_key_event(s->kbd, code, !(keycode & 0x80)); +} + +#define M 0 + +static int n810_keys[0x80] = { + [0x01] = 16, /* Q */ + [0x02] = 37, /* K */ + [0x03] = 24, /* O */ + [0x04] = 25, /* P */ + [0x05] = 14, /* Backspace */ + [0x06] = 30, /* A */ + [0x07] = 31, /* S */ + [0x08] = 32, /* D */ + [0x09] = 33, /* F */ + [0x0a] = 34, /* G */ + [0x0b] = 35, /* H */ + [0x0c] = 36, /* J */ + + [0x11] = 17, /* W */ + [0x12] = 62, /* Menu (F4) */ + [0x13] = 38, /* L */ + [0x14] = 40, /* ' (Apostrophe) */ + [0x16] = 44, /* Z */ + [0x17] = 45, /* X */ + [0x18] = 46, /* C */ + [0x19] = 47, /* V */ + [0x1a] = 48, /* B */ + [0x1b] = 49, /* N */ + [0x1c] = 42, /* Shift (Left shift) */ + [0x1f] = 65, /* Zoom+ (F7) */ + + [0x21] = 18, /* E */ + [0x22] = 39, /* ; (Semicolon) */ + [0x23] = 12, /* - (Minus) */ + [0x24] = 13, /* = (Equal) */ + [0x2b] = 56, /* Fn (Left Alt) */ + [0x2c] = 50, /* M */ + [0x2f] = 66, /* Zoom- (F8) */ + + [0x31] = 19, /* R */ + [0x32] = 29 | M, /* Right Ctrl */ + [0x34] = 57, /* Space */ + [0x35] = 51, /* , (Comma) */ + [0x37] = 72 | M, /* Up */ + [0x3c] = 82 | M, /* Compose (Insert) */ + [0x3f] = 64, /* FullScreen (F6) */ + + [0x41] = 20, /* T */ + [0x44] = 52, /* . (Dot) */ + [0x46] = 77 | M, /* Right */ + [0x4f] = 63, /* Home (F5) */ + [0x51] = 21, /* Y */ + [0x53] = 80 | M, /* Down */ + [0x55] = 28, /* Enter */ + [0x5f] = 1, /* Cycle (ESC) */ + + [0x61] = 22, /* U */ + [0x64] = 75 | M, /* Left */ + + [0x71] = 23, /* I */ +#if 0 + [0x75] = 28 | M, /* KP Enter (KP Enter) */ +#else + [0x75] = 15, /* KP Enter (Tab) */ +#endif +}; + +#undef M + +static void n810_kbd_setup(struct n800_s *s) +{ + qemu_irq kbd_irq = omap2_gpio_in_get(s->cpu->gpif, N810_KEYBOARD_GPIO)[0]; + int i; + + for (i = 0; i < 0x80; i ++) + s->keymap[i] = -1; + for (i = 0; i < 0x80; i ++) + if (n810_keys[i] > 0) + s->keymap[n810_keys[i]] = i; + + qemu_add_kbd_event_handler(n810_key_event, s); + + /* Attach the LM8322 keyboard to the I2C bus, + * should happen in n8x0_i2c_setup and s->kbd be initialised here. */ + s->kbd = lm8323_init(s->i2c, kbd_irq); + i2c_set_slave_address(s->kbd, N810_LM8323_ADDR); +} + /* LCD MIPI DBI-C controller (URAL) */ struct mipid_s { int resp[4]; @@ -954,8 +1062,10 @@ static void n8x0_init(ram_addr_t ram_size, const char *boot_device, n8x0_i2c_setup(s); if (model == 800) n800_tsc_kbd_setup(s); - else if (model == 810) + else if (model == 810) { n810_tsc_setup(s); + n810_kbd_setup(s); + } n8x0_spi_setup(s); n8x0_dss_setup(s, ds); n8x0_cbus_setup(s); |