diff options
Diffstat (limited to 'drivers/net/ethernet/intel/ice/ice_ptp_hw.c')
-rw-r--r-- | drivers/net/ethernet/intel/ice/ice_ptp_hw.c | 651 |
1 files changed, 651 insertions, 0 deletions
diff --git a/drivers/net/ethernet/intel/ice/ice_ptp_hw.c b/drivers/net/ethernet/intel/ice/ice_ptp_hw.c new file mode 100644 index 000000000000..3eca0e4eab0b --- /dev/null +++ b/drivers/net/ethernet/intel/ice/ice_ptp_hw.c @@ -0,0 +1,651 @@ +// SPDX-License-Identifier: GPL-2.0 +/* Copyright (C) 2021, Intel Corporation. */ + +#include "ice_common.h" +#include "ice_ptp_hw.h" + +/* Low level functions for interacting with and managing the device clock used + * for the Precision Time Protocol. + * + * The ice hardware represents the current time using three registers: + * + * GLTSYN_TIME_H GLTSYN_TIME_L GLTSYN_TIME_R + * +---------------+ +---------------+ +---------------+ + * | 32 bits | | 32 bits | | 32 bits | + * +---------------+ +---------------+ +---------------+ + * + * The registers are incremented every clock tick using a 40bit increment + * value defined over two registers: + * + * GLTSYN_INCVAL_H GLTSYN_INCVAL_L + * +---------------+ +---------------+ + * | 8 bit s | | 32 bits | + * +---------------+ +---------------+ + * + * The increment value is added to the GLSTYN_TIME_R and GLSTYN_TIME_L + * registers every clock source tick. Depending on the specific device + * configuration, the clock source frequency could be one of a number of + * values. + * + * For E810 devices, the increment frequency is 812.5 MHz + * + * The hardware captures timestamps in the PHY for incoming packets, and for + * outgoing packets on request. To support this, the PHY maintains a timer + * that matches the lower 64 bits of the global source timer. + * + * In order to ensure that the PHY timers and the source timer are equivalent, + * shadow registers are used to prepare the desired initial values. A special + * sync command is issued to trigger copying from the shadow registers into + * the appropriate source and PHY registers simultaneously. + */ + +/** + * ice_get_ptp_src_clock_index - determine source clock index + * @hw: pointer to HW struct + * + * Determine the source clock index currently in use, based on device + * capabilities reported during initialization. + */ +u8 ice_get_ptp_src_clock_index(struct ice_hw *hw) +{ + return hw->func_caps.ts_func_info.tmr_index_assoc; +} + +/* E810 functions + * + * The following functions operate on the E810 series devices which use + * a separate external PHY. + */ + +/** + * ice_read_phy_reg_e810 - Read register from external PHY on E810 + * @hw: pointer to the HW struct + * @addr: the address to read from + * @val: On return, the value read from the PHY + * + * Read a register from the external PHY on the E810 device. + */ +static int ice_read_phy_reg_e810(struct ice_hw *hw, u32 addr, u32 *val) +{ + struct ice_sbq_msg_input msg = {0}; + int status; + + msg.msg_addr_low = lower_16_bits(addr); + msg.msg_addr_high = upper_16_bits(addr); + msg.opcode = ice_sbq_msg_rd; + msg.dest_dev = rmn_0; + + status = ice_sbq_rw_reg(hw, &msg); + if (status) { + ice_debug(hw, ICE_DBG_PTP, "Failed to send message to PHY, status %d\n", + status); + return status; + } + + *val = msg.data; + + return 0; +} + +/** + * ice_write_phy_reg_e810 - Write register on external PHY on E810 + * @hw: pointer to the HW struct + * @addr: the address to writem to + * @val: the value to write to the PHY + * + * Write a value to a register of the external PHY on the E810 device. + */ +static int ice_write_phy_reg_e810(struct ice_hw *hw, u32 addr, u32 val) +{ + struct ice_sbq_msg_input msg = {0}; + int status; + + msg.msg_addr_low = lower_16_bits(addr); + msg.msg_addr_high = upper_16_bits(addr); + msg.opcode = ice_sbq_msg_wr; + msg.dest_dev = rmn_0; + msg.data = val; + + status = ice_sbq_rw_reg(hw, &msg); + if (status) { + ice_debug(hw, ICE_DBG_PTP, "Failed to send message to PHY, status %d\n", + status); + return status; + } + + return 0; +} + +/** + * ice_read_phy_tstamp_e810 - Read a PHY timestamp out of the external PHY + * @hw: pointer to the HW struct + * @lport: the lport to read from + * @idx: the timestamp index to read + * @tstamp: on return, the 40bit timestamp value + * + * Read a 40bit timestamp value out of the timestamp block of the external PHY + * on the E810 device. + */ +static int +ice_read_phy_tstamp_e810(struct ice_hw *hw, u8 lport, u8 idx, u64 *tstamp) +{ + u32 lo_addr, hi_addr, lo, hi; + int status; + + lo_addr = TS_EXT(LOW_TX_MEMORY_BANK_START, lport, idx); + hi_addr = TS_EXT(HIGH_TX_MEMORY_BANK_START, lport, idx); + + status = ice_read_phy_reg_e810(hw, lo_addr, &lo); + if (status) { + ice_debug(hw, ICE_DBG_PTP, "Failed to read low PTP timestamp register, status %d\n", + status); + return status; + } + + status = ice_read_phy_reg_e810(hw, hi_addr, &hi); + if (status) { + ice_debug(hw, ICE_DBG_PTP, "Failed to read high PTP timestamp register, status %d\n", + status); + return status; + } + + /* For E810 devices, the timestamp is reported with the lower 32 bits + * in the low register, and the upper 8 bits in the high register. + */ + *tstamp = ((u64)hi) << TS_HIGH_S | ((u64)lo & TS_LOW_M); + + return 0; +} + +/** + * ice_clear_phy_tstamp_e810 - Clear a timestamp from the external PHY + * @hw: pointer to the HW struct + * @lport: the lport to read from + * @idx: the timestamp index to reset + * + * Clear a timestamp, resetting its valid bit, from the timestamp block of the + * external PHY on the E810 device. + */ +static int ice_clear_phy_tstamp_e810(struct ice_hw *hw, u8 lport, u8 idx) +{ + u32 lo_addr, hi_addr; + int status; + + lo_addr = TS_EXT(LOW_TX_MEMORY_BANK_START, lport, idx); + hi_addr = TS_EXT(HIGH_TX_MEMORY_BANK_START, lport, idx); + + status = ice_write_phy_reg_e810(hw, lo_addr, 0); + if (status) { + ice_debug(hw, ICE_DBG_PTP, "Failed to clear low PTP timestamp register, status %d\n", + status); + return status; + } + + status = ice_write_phy_reg_e810(hw, hi_addr, 0); + if (status) { + ice_debug(hw, ICE_DBG_PTP, "Failed to clear high PTP timestamp register, status %d\n", + status); + return status; + } + + return 0; +} + +/** + * ice_ptp_init_phy_e810 - Enable PTP function on the external PHY + * @hw: pointer to HW struct + * + * Enable the timesync PTP functionality for the external PHY connected to + * this function. + */ +int ice_ptp_init_phy_e810(struct ice_hw *hw) +{ + int status; + u8 tmr_idx; + + tmr_idx = hw->func_caps.ts_func_info.tmr_index_owned; + status = ice_write_phy_reg_e810(hw, ETH_GLTSYN_ENA(tmr_idx), + GLTSYN_ENA_TSYN_ENA_M); + if (status) + ice_debug(hw, ICE_DBG_PTP, "PTP failed in ena_phy_time_syn %d\n", + status); + + return status; +} + +/** + * ice_ptp_prep_phy_time_e810 - Prepare PHY port with initial time + * @hw: Board private structure + * @time: Time to initialize the PHY port clock to + * + * Program the PHY port ETH_GLTSYN_SHTIME registers in preparation setting the + * initial clock time. The time will not actually be programmed until the + * driver issues an INIT_TIME command. + * + * The time value is the upper 32 bits of the PHY timer, usually in units of + * nominal nanoseconds. + */ +static int ice_ptp_prep_phy_time_e810(struct ice_hw *hw, u32 time) +{ + int status; + u8 tmr_idx; + + tmr_idx = hw->func_caps.ts_func_info.tmr_index_owned; + status = ice_write_phy_reg_e810(hw, ETH_GLTSYN_SHTIME_0(tmr_idx), 0); + if (status) { + ice_debug(hw, ICE_DBG_PTP, "Failed to write SHTIME_0, status %d\n", + status); + return status; + } + + status = ice_write_phy_reg_e810(hw, ETH_GLTSYN_SHTIME_L(tmr_idx), time); + if (status) { + ice_debug(hw, ICE_DBG_PTP, "Failed to write SHTIME_L, status %d\n", + status); + return status; + } + + return 0; +} + +/** + * ice_ptp_prep_phy_adj_e810 - Prep PHY port for a time adjustment + * @hw: pointer to HW struct + * @adj: adjustment value to program + * + * Prepare the PHY port for an atomic adjustment by programming the PHY + * ETH_GLTSYN_SHADJ_L and ETH_GLTSYN_SHADJ_H registers. The actual adjustment + * is completed by issuing an ADJ_TIME sync command. + * + * The adjustment value only contains the portion used for the upper 32bits of + * the PHY timer, usually in units of nominal nanoseconds. Negative + * adjustments are supported using 2s complement arithmetic. + */ +static int ice_ptp_prep_phy_adj_e810(struct ice_hw *hw, s32 adj) +{ + int status; + u8 tmr_idx; + + tmr_idx = hw->func_caps.ts_func_info.tmr_index_owned; + + /* Adjustments are represented as signed 2's complement values in + * nanoseconds. Sub-nanosecond adjustment is not supported. + */ + status = ice_write_phy_reg_e810(hw, ETH_GLTSYN_SHADJ_L(tmr_idx), 0); + if (status) { + ice_debug(hw, ICE_DBG_PTP, "Failed to write adj to PHY SHADJ_L, status %d\n", + status); + return status; + } + + status = ice_write_phy_reg_e810(hw, ETH_GLTSYN_SHADJ_H(tmr_idx), adj); + if (status) { + ice_debug(hw, ICE_DBG_PTP, "Failed to write adj to PHY SHADJ_H, status %d\n", + status); + return status; + } + + return 0; +} + +/** + * ice_ptp_prep_phy_incval_e810 - Prep PHY port increment value change + * @hw: pointer to HW struct + * @incval: The new 40bit increment value to prepare + * + * Prepare the PHY port for a new increment value by programming the PHY + * ETH_GLTSYN_SHADJ_L and ETH_GLTSYN_SHADJ_H registers. The actual change is + * completed by issuing an INIT_INCVAL command. + */ +static int ice_ptp_prep_phy_incval_e810(struct ice_hw *hw, u64 incval) +{ + u32 high, low; + int status; + u8 tmr_idx; + + tmr_idx = hw->func_caps.ts_func_info.tmr_index_owned; + low = lower_32_bits(incval); + high = upper_32_bits(incval); + + status = ice_write_phy_reg_e810(hw, ETH_GLTSYN_SHADJ_L(tmr_idx), low); + if (status) { + ice_debug(hw, ICE_DBG_PTP, "Failed to write incval to PHY SHADJ_L, status %d\n", + status); + return status; + } + + status = ice_write_phy_reg_e810(hw, ETH_GLTSYN_SHADJ_H(tmr_idx), high); + if (status) { + ice_debug(hw, ICE_DBG_PTP, "Failed to write incval PHY SHADJ_H, status %d\n", + status); + return status; + } + + return 0; +} + +/** + * ice_ptp_port_cmd_e810 - Prepare all external PHYs for a timer command + * @hw: pointer to HW struct + * @cmd: Command to be sent to the port + * + * Prepare the external PHYs connected to this device for a timer sync + * command. + */ +static int ice_ptp_port_cmd_e810(struct ice_hw *hw, enum ice_ptp_tmr_cmd cmd) +{ + u32 cmd_val, val; + int status; + + switch (cmd) { + case INIT_TIME: + cmd_val = GLTSYN_CMD_INIT_TIME; + break; + case INIT_INCVAL: + cmd_val = GLTSYN_CMD_INIT_INCVAL; + break; + case ADJ_TIME: + cmd_val = GLTSYN_CMD_ADJ_TIME; + break; + case READ_TIME: + cmd_val = GLTSYN_CMD_READ_TIME; + break; + case ADJ_TIME_AT_TIME: + cmd_val = GLTSYN_CMD_ADJ_INIT_TIME; + break; + } + + /* Read, modify, write */ + status = ice_read_phy_reg_e810(hw, ETH_GLTSYN_CMD, &val); + if (status) { + ice_debug(hw, ICE_DBG_PTP, "Failed to read GLTSYN_CMD, status %d\n", status); + return status; + } + + /* Modify necessary bits only and perform write */ + val &= ~TS_CMD_MASK_E810; + val |= cmd_val; + + status = ice_write_phy_reg_e810(hw, ETH_GLTSYN_CMD, val); + if (status) { + ice_debug(hw, ICE_DBG_PTP, "Failed to write back GLTSYN_CMD, status %d\n", status); + return status; + } + + return 0; +} + +/* Device agnostic functions + * + * The following functions implement useful behavior to hide the differences + * between E810 and other devices. They call the device-specific + * implementations where necessary. + * + * Currently, the driver only supports E810, but future work will enable + * support for E822-based devices. + */ + +/** + * ice_ptp_lock - Acquire PTP global semaphore register lock + * @hw: pointer to the HW struct + * + * Acquire the global PTP hardware semaphore lock. Returns true if the lock + * was acquired, false otherwise. + * + * The PFTSYN_SEM register sets the busy bit on read, returning the previous + * value. If software sees the busy bit cleared, this means that this function + * acquired the lock (and the busy bit is now set). If software sees the busy + * bit set, it means that another function acquired the lock. + * + * Software must clear the busy bit with a write to release the lock for other + * functions when done. + */ +bool ice_ptp_lock(struct ice_hw *hw) +{ + u32 hw_lock; + int i; + +#define MAX_TRIES 5 + + for (i = 0; i < MAX_TRIES; i++) { + hw_lock = rd32(hw, PFTSYN_SEM + (PFTSYN_SEM_BYTES * hw->pf_id)); + hw_lock = hw_lock & PFTSYN_SEM_BUSY_M; + if (!hw_lock) + break; + + /* Somebody is holding the lock */ + usleep_range(10000, 20000); + } + + return !hw_lock; +} + +/** + * ice_ptp_unlock - Release PTP global semaphore register lock + * @hw: pointer to the HW struct + * + * Release the global PTP hardware semaphore lock. This is done by writing to + * the PFTSYN_SEM register. + */ +void ice_ptp_unlock(struct ice_hw *hw) +{ + wr32(hw, PFTSYN_SEM + (PFTSYN_SEM_BYTES * hw->pf_id), 0); +} + +/** + * ice_ptp_src_cmd - Prepare source timer for a timer command + * @hw: pointer to HW structure + * @cmd: Timer command + * + * Prepare the source timer for an upcoming timer sync command. + */ +static void ice_ptp_src_cmd(struct ice_hw *hw, enum ice_ptp_tmr_cmd cmd) +{ + u32 cmd_val; + u8 tmr_idx; + + tmr_idx = ice_get_ptp_src_clock_index(hw); + cmd_val = tmr_idx << SEL_CPK_SRC; + + switch (cmd) { + case INIT_TIME: + cmd_val |= GLTSYN_CMD_INIT_TIME; + break; + case INIT_INCVAL: + cmd_val |= GLTSYN_CMD_INIT_INCVAL; + break; + case ADJ_TIME: + cmd_val |= GLTSYN_CMD_ADJ_TIME; + break; + case ADJ_TIME_AT_TIME: + cmd_val |= GLTSYN_CMD_ADJ_INIT_TIME; + break; + case READ_TIME: + cmd_val |= GLTSYN_CMD_READ_TIME; + break; + } + + wr32(hw, GLTSYN_CMD, cmd_val); +} + +/** + * ice_ptp_tmr_cmd - Prepare and trigger a timer sync command + * @hw: pointer to HW struct + * @cmd: the command to issue + * + * Prepare the source timer and PHY timers and then trigger the requested + * command. This causes the shadow registers previously written in preparation + * for the command to be synchronously applied to both the source and PHY + * timers. + */ +static int ice_ptp_tmr_cmd(struct ice_hw *hw, enum ice_ptp_tmr_cmd cmd) +{ + int status; + + /* First, prepare the source timer */ + ice_ptp_src_cmd(hw, cmd); + + /* Next, prepare the ports */ + status = ice_ptp_port_cmd_e810(hw, cmd); + if (status) { + ice_debug(hw, ICE_DBG_PTP, "Failed to prepare PHY ports for timer command %u, status %d\n", + cmd, status); + return status; + } + + /* Write the sync command register to drive both source and PHY timer commands + * synchronously + */ + wr32(hw, GLTSYN_CMD_SYNC, SYNC_EXEC_CMD); + + return 0; +} + +/** + * ice_ptp_init_time - Initialize device time to provided value + * @hw: pointer to HW struct + * @time: 64bits of time (GLTSYN_TIME_L and GLTSYN_TIME_H) + * + * Initialize the device to the specified time provided. This requires a three + * step process: + * + * 1) write the new init time to the source timer shadow registers + * 2) write the new init time to the PHY timer shadow registers + * 3) issue an init_time timer command to synchronously switch both the source + * and port timers to the new init time value at the next clock cycle. + */ +int ice_ptp_init_time(struct ice_hw *hw, u64 time) +{ + int status; + u8 tmr_idx; + + tmr_idx = hw->func_caps.ts_func_info.tmr_index_owned; + + /* Source timers */ + wr32(hw, GLTSYN_SHTIME_L(tmr_idx), lower_32_bits(time)); + wr32(hw, GLTSYN_SHTIME_H(tmr_idx), upper_32_bits(time)); + wr32(hw, GLTSYN_SHTIME_0(tmr_idx), 0); + + /* PHY timers */ + /* Fill Rx and Tx ports and send msg to PHY */ + status = ice_ptp_prep_phy_time_e810(hw, time & 0xFFFFFFFF); + if (status) + return status; + + return ice_ptp_tmr_cmd(hw, INIT_TIME); +} + +/** + * ice_ptp_write_incval - Program PHC with new increment value + * @hw: pointer to HW struct + * @incval: Source timer increment value per clock cycle + * + * Program the PHC with a new increment value. This requires a three-step + * process: + * + * 1) Write the increment value to the source timer shadow registers + * 2) Write the increment value to the PHY timer shadow registers + * 3) Issue an INIT_INCVAL timer command to synchronously switch both the + * source and port timers to the new increment value at the next clock + * cycle. + */ +int ice_ptp_write_incval(struct ice_hw *hw, u64 incval) +{ + int status; + u8 tmr_idx; + + tmr_idx = hw->func_caps.ts_func_info.tmr_index_owned; + + /* Shadow Adjust */ + wr32(hw, GLTSYN_SHADJ_L(tmr_idx), lower_32_bits(incval)); + wr32(hw, GLTSYN_SHADJ_H(tmr_idx), upper_32_bits(incval)); + + status = ice_ptp_prep_phy_incval_e810(hw, incval); + if (status) + return status; + + return ice_ptp_tmr_cmd(hw, INIT_INCVAL); +} + +/** + * ice_ptp_write_incval_locked - Program new incval while holding semaphore + * @hw: pointer to HW struct + * @incval: Source timer increment value per clock cycle + * + * Program a new PHC incval while holding the PTP semaphore. + */ +int ice_ptp_write_incval_locked(struct ice_hw *hw, u64 incval) +{ + int status; + + if (!ice_ptp_lock(hw)) + return -EBUSY; + + status = ice_ptp_write_incval(hw, incval); + + ice_ptp_unlock(hw); + + return status; +} + +/** + * ice_ptp_adj_clock - Adjust PHC clock time atomically + * @hw: pointer to HW struct + * @adj: Adjustment in nanoseconds + * + * Perform an atomic adjustment of the PHC time by the specified number of + * nanoseconds. This requires a three-step process: + * + * 1) Write the adjustment to the source timer shadow registers + * 2) Write the adjustment to the PHY timer shadow registers + * 3) Issue an ADJ_TIME timer command to synchronously apply the adjustment to + * both the source and port timers at the next clock cycle. + */ +int ice_ptp_adj_clock(struct ice_hw *hw, s32 adj) +{ + int status; + u8 tmr_idx; + + tmr_idx = hw->func_caps.ts_func_info.tmr_index_owned; + + /* Write the desired clock adjustment into the GLTSYN_SHADJ register. + * For an ADJ_TIME command, this set of registers represents the value + * to add to the clock time. It supports subtraction by interpreting + * the value as a 2's complement integer. + */ + wr32(hw, GLTSYN_SHADJ_L(tmr_idx), 0); + wr32(hw, GLTSYN_SHADJ_H(tmr_idx), adj); + + status = ice_ptp_prep_phy_adj_e810(hw, adj); + if (status) + return status; + + return ice_ptp_tmr_cmd(hw, ADJ_TIME); +} + +/** + * ice_read_phy_tstamp - Read a PHY timestamp from the timestamo block + * @hw: pointer to the HW struct + * @block: the block to read from + * @idx: the timestamp index to read + * @tstamp: on return, the 40bit timestamp value + * + * Read a 40bit timestamp value out of the timestamp block. + */ +int ice_read_phy_tstamp(struct ice_hw *hw, u8 block, u8 idx, u64 *tstamp) +{ + return ice_read_phy_tstamp_e810(hw, block, idx, tstamp); +} + +/** + * ice_clear_phy_tstamp - Clear a timestamp from the timestamp block + * @hw: pointer to the HW struct + * @block: the block to read from + * @idx: the timestamp index to reset + * + * Clear a timestamp, resetting its valid bit, from the timestamp block. + */ +int ice_clear_phy_tstamp(struct ice_hw *hw, u8 block, u8 idx) +{ + return ice_clear_phy_tstamp_e810(hw, block, idx); +} |