diff options
Diffstat (limited to 'arch/arm64/boot/dts/marvell')
| -rw-r--r-- | arch/arm64/boot/dts/marvell/Makefile | 1 | ||||
| -rw-r--r-- | arch/arm64/boot/dts/marvell/armada-3720-espressobin.dts | 22 | ||||
| -rw-r--r-- | arch/arm64/boot/dts/marvell/armada-37xx.dtsi | 10 | ||||
| -rw-r--r-- | arch/arm64/boot/dts/marvell/armada-8040-clearfog-gt-8k.dts | 22 | ||||
| -rw-r--r-- | arch/arm64/boot/dts/marvell/armada-8040-mcbin-singleshot.dts | 29 | ||||
| -rw-r--r-- | arch/arm64/boot/dts/marvell/armada-8040-mcbin.dts | 333 | ||||
| -rw-r--r-- | arch/arm64/boot/dts/marvell/armada-8040-mcbin.dtsi | 346 |
7 files changed, 433 insertions, 330 deletions
diff --git a/arch/arm64/boot/dts/marvell/Makefile b/arch/arm64/boot/dts/marvell/Makefile index eca8bac6303a..2eff1f927471 100644 --- a/arch/arm64/boot/dts/marvell/Makefile +++ b/arch/arm64/boot/dts/marvell/Makefile @@ -6,4 +6,5 @@ dtb-$(CONFIG_ARCH_MVEBU) += armada-7040-db.dtb dtb-$(CONFIG_ARCH_MVEBU) += armada-8040-clearfog-gt-8k.dtb dtb-$(CONFIG_ARCH_MVEBU) += armada-8040-db.dtb dtb-$(CONFIG_ARCH_MVEBU) += armada-8040-mcbin.dtb +dtb-$(CONFIG_ARCH_MVEBU) += armada-8040-mcbin-singleshot.dtb dtb-$(CONFIG_ARCH_MVEBU) += armada-8080-db.dtb diff --git a/arch/arm64/boot/dts/marvell/armada-3720-espressobin.dts b/arch/arm64/boot/dts/marvell/armada-3720-espressobin.dts index 3ab25ad402b9..846003bb480c 100644 --- a/arch/arm64/boot/dts/marvell/armada-3720-espressobin.dts +++ b/arch/arm64/boot/dts/marvell/armada-3720-espressobin.dts @@ -60,9 +60,31 @@ cd-gpios = <&gpionb 3 GPIO_ACTIVE_LOW>; marvell,pad-type = "sd"; vqmmc-supply = <&vcc_sd_reg1>; + + pinctrl-names = "default"; + pinctrl-0 = <&sdio_pins>; status = "okay"; }; +/* U11 */ +&sdhci0 { + non-removable; + bus-width = <8>; + mmc-ddr-1_8v; + mmc-hs400-1_8v; + marvell,xenon-emmc; + marvell,xenon-tun-count = <9>; + marvell,pad-type = "fixed-1-8v"; + + pinctrl-names = "default"; + pinctrl-0 = <&mmc_pins>; +/* + * This eMMC is not populated on all boards, so disable it by + * default and let the bootloader enable it, if it is present + */ + status = "disabled"; +}; + &spi0 { status = "okay"; diff --git a/arch/arm64/boot/dts/marvell/armada-37xx.dtsi b/arch/arm64/boot/dts/marvell/armada-37xx.dtsi index 4472bcd8f9fb..e05594ea15fb 100644 --- a/arch/arm64/boot/dts/marvell/armada-37xx.dtsi +++ b/arch/arm64/boot/dts/marvell/armada-37xx.dtsi @@ -234,6 +234,11 @@ groups = "uart2"; function = "uart"; }; + + mmc_pins: mmc-pins { + groups = "emmc_nb"; + function = "emmc"; + }; }; nb_pm: syscon@14000 { @@ -266,6 +271,11 @@ function = "mii"; }; + sdio_pins: sdio-pins { + groups = "sdio_sb"; + function = "sdio"; + }; + }; eth0: ethernet@30000 { diff --git a/arch/arm64/boot/dts/marvell/armada-8040-clearfog-gt-8k.dts b/arch/arm64/boot/dts/marvell/armada-8040-clearfog-gt-8k.dts index 9473d40a292a..5b4a9609e31f 100644 --- a/arch/arm64/boot/dts/marvell/armada-8040-clearfog-gt-8k.dts +++ b/arch/arm64/boot/dts/marvell/armada-8040-clearfog-gt-8k.dts @@ -42,7 +42,7 @@ v_5v0_usb3_hst_vbus: regulator-usb3-vbus0 { compatible = "regulator-fixed"; - gpio = <&cp0_gpio2 15 GPIO_ACTIVE_HIGH>; + gpio = <&cp0_gpio2 15 GPIO_ACTIVE_LOW>; pinctrl-names = "default"; pinctrl-0 = <&cp0_xhci_vbus_pins>; regulator-name = "v_5v0_usb3_hst_vbus"; @@ -246,6 +246,18 @@ gpios = <1 GPIO_ACTIVE_HIGH>; output-high; }; + + lte_reset { + gpio-hog; + gpios = <2 GPIO_ACTIVE_LOW>; + output-low; + }; + + lte_disable { + gpio-hog; + gpios = <21 GPIO_ACTIVE_LOW>; + output-low; + }; }; &cp0_ethernet { @@ -270,6 +282,10 @@ vqmmc-supply = <&v_3_3>; }; +&cp0_usb3_1 { + status = "okay"; +}; + &cp1_pinctrl { /* * MPP Bus: @@ -333,6 +349,10 @@ */ marvell,reg-init = <3 16 0 0x1017>; reg = <0>; + pinctrl-names = "default"; + pinctrl-0 = <&cp0_copper_eth_phy_reset>; + reset-gpios = <&cp1_gpio1 11 GPIO_ACTIVE_LOW>; + reset-assert-us = <10000>; }; switch0: switch0@4 { diff --git a/arch/arm64/boot/dts/marvell/armada-8040-mcbin-singleshot.dts b/arch/arm64/boot/dts/marvell/armada-8040-mcbin-singleshot.dts new file mode 100644 index 000000000000..c3e18fd5bc27 --- /dev/null +++ b/arch/arm64/boot/dts/marvell/armada-8040-mcbin-singleshot.dts @@ -0,0 +1,29 @@ +// SPDX-License-Identifier: (GPL-2.0+ OR MIT) +/* + * Copyright (C) 2016 Marvell Technology Group Ltd. + * + * Device Tree file for MACCHIATOBin Armada 8040 community board platform + */ + +#include "armada-8040-mcbin.dtsi" + +/ { + model = "Marvell 8040 MACCHIATOBin Single-shot"; + compatible = "marvell,armada8040-mcbin-singleshot", + "marvell,armada8040-mcbin", "marvell,armada8040", + "marvell,armada-ap806-quad", "marvell,armada-ap806"; +}; + +&cp0_eth0 { + status = "okay"; + phy-mode = "10gbase-kr"; + managed = "in-band-status"; + sfp = <&sfp_eth0>; +}; + +&cp1_eth0 { + status = "okay"; + phy-mode = "10gbase-kr"; + managed = "in-band-status"; + sfp = <&sfp_eth1>; +}; diff --git a/arch/arm64/boot/dts/marvell/armada-8040-mcbin.dts b/arch/arm64/boot/dts/marvell/armada-8040-mcbin.dts index 56fa44860909..d06f5ab7ddab 100644 --- a/arch/arm64/boot/dts/marvell/armada-8040-mcbin.dts +++ b/arch/arm64/boot/dts/marvell/armada-8040-mcbin.dts @@ -5,226 +5,13 @@ * Device Tree file for MACCHIATOBin Armada 8040 community board platform */ -#include "armada-8040.dtsi" - -#include <dt-bindings/gpio/gpio.h> +#include "armada-8040-mcbin.dtsi" / { - model = "Marvell 8040 MACCHIATOBin"; - compatible = "marvell,armada8040-mcbin", "marvell,armada8040", + model = "Marvell 8040 MACCHIATOBin Double-shot"; + compatible = "marvell,armada8040-mcbin-doubleshot", + "marvell,armada8040-mcbin", "marvell,armada8040", "marvell,armada-ap806-quad", "marvell,armada-ap806"; - - chosen { - stdout-path = "serial0:115200n8"; - }; - - memory@0 { - device_type = "memory"; - reg = <0x0 0x0 0x0 0x80000000>; - }; - - aliases { - ethernet0 = &cp0_eth0; - ethernet1 = &cp1_eth0; - ethernet2 = &cp1_eth1; - ethernet3 = &cp1_eth2; - }; - - /* Regulator labels correspond with schematics */ - v_3_3: regulator-3-3v { - compatible = "regulator-fixed"; - regulator-name = "v_3_3"; - regulator-min-microvolt = <3300000>; - regulator-max-microvolt = <3300000>; - regulator-always-on; - status = "okay"; - }; - - v_vddo_h: regulator-1-8v { - compatible = "regulator-fixed"; - regulator-name = "v_vddo_h"; - regulator-min-microvolt = <1800000>; - regulator-max-microvolt = <1800000>; - regulator-always-on; - status = "okay"; - }; - - v_5v0_usb3_hst_vbus: regulator-usb3-vbus0 { - compatible = "regulator-fixed"; - enable-active-high; - gpio = <&cp0_gpio2 15 GPIO_ACTIVE_HIGH>; - pinctrl-names = "default"; - pinctrl-0 = <&cp0_xhci_vbus_pins>; - regulator-name = "v_5v0_usb3_hst_vbus"; - regulator-min-microvolt = <5000000>; - regulator-max-microvolt = <5000000>; - status = "okay"; - }; - - usb3h0_phy: usb3_phy0 { - compatible = "usb-nop-xceiv"; - vcc-supply = <&v_5v0_usb3_hst_vbus>; - }; - - sfp_eth0: sfp-eth0 { - /* CON15,16 - CPM lane 4 */ - compatible = "sff,sfp"; - i2c-bus = <&sfpp0_i2c>; - los-gpio = <&cp1_gpio1 28 GPIO_ACTIVE_HIGH>; - mod-def0-gpio = <&cp1_gpio1 27 GPIO_ACTIVE_LOW>; - tx-disable-gpio = <&cp1_gpio1 29 GPIO_ACTIVE_HIGH>; - tx-fault-gpio = <&cp1_gpio1 26 GPIO_ACTIVE_HIGH>; - pinctrl-names = "default"; - pinctrl-0 = <&cp1_sfpp0_pins>; - }; - - sfp_eth1: sfp-eth1 { - /* CON17,18 - CPS lane 4 */ - compatible = "sff,sfp"; - i2c-bus = <&sfpp1_i2c>; - los-gpio = <&cp1_gpio1 8 GPIO_ACTIVE_HIGH>; - mod-def0-gpio = <&cp1_gpio1 11 GPIO_ACTIVE_LOW>; - tx-disable-gpio = <&cp1_gpio1 10 GPIO_ACTIVE_HIGH>; - tx-fault-gpio = <&cp0_gpio2 30 GPIO_ACTIVE_HIGH>; - pinctrl-names = "default"; - pinctrl-0 = <&cp1_sfpp1_pins &cp0_sfpp1_pins>; - }; - - sfp_eth3: sfp-eth3 { - /* CON13,14 - CPS lane 5 */ - compatible = "sff,sfp"; - i2c-bus = <&sfp_1g_i2c>; - los-gpio = <&cp0_gpio2 22 GPIO_ACTIVE_HIGH>; - mod-def0-gpio = <&cp0_gpio2 21 GPIO_ACTIVE_LOW>; - tx-disable-gpio = <&cp1_gpio1 24 GPIO_ACTIVE_HIGH>; - tx-fault-gpio = <&cp0_gpio2 19 GPIO_ACTIVE_HIGH>; - pinctrl-names = "default"; - pinctrl-0 = <&cp0_sfp_1g_pins &cp1_sfp_1g_pins>; - }; -}; - -&uart0 { - status = "okay"; - pinctrl-0 = <&uart0_pins>; - pinctrl-names = "default"; -}; - -&ap_sdhci0 { - bus-width = <8>; - /* - * Not stable in HS modes - phy needs "more calibration", so add - * the "slow-mode" and disable SDR104, SDR50 and DDR50 modes. - */ - marvell,xenon-phy-slow-mode; - no-1-8-v; - no-sd; - no-sdio; - non-removable; - status = "okay"; - vqmmc-supply = <&v_vddo_h>; -}; - -&cp0_i2c0 { - clock-frequency = <100000>; - pinctrl-names = "default"; - pinctrl-0 = <&cp0_i2c0_pins>; - status = "okay"; -}; - -&cp0_i2c1 { - clock-frequency = <100000>; - pinctrl-names = "default"; - pinctrl-0 = <&cp0_i2c1_pins>; - status = "okay"; - - i2c-switch@70 { - compatible = "nxp,pca9548"; - #address-cells = <1>; - #size-cells = <0>; - reg = <0x70>; - - sfpp0_i2c: i2c@0 { - #address-cells = <1>; - #size-cells = <0>; - reg = <0>; - }; - sfpp1_i2c: i2c@1 { - #address-cells = <1>; - #size-cells = <0>; - reg = <1>; - }; - sfp_1g_i2c: i2c@2 { - #address-cells = <1>; - #size-cells = <0>; - reg = <2>; - }; - }; -}; - -/* J25 UART header */ -&cp0_uart1 { - pinctrl-names = "default"; - pinctrl-0 = <&cp0_uart1_pins>; - status = "okay"; -}; - -&cp0_mdio { - pinctrl-names = "default"; - pinctrl-0 = <&cp0_ge_mdio_pins>; - status = "okay"; - - ge_phy: ethernet-phy@0 { - reg = <0>; - }; -}; - -&cp0_pcie0 { - pinctrl-names = "default"; - pinctrl-0 = <&cp0_pcie_pins>; - num-lanes = <4>; - num-viewport = <8>; - reset-gpio = <&cp0_gpio1 20 GPIO_ACTIVE_LOW>; - status = "okay"; -}; - -&cp0_pinctrl { - cp0_ge_mdio_pins: ge-mdio-pins { - marvell,pins = "mpp32", "mpp34"; - marvell,function = "ge"; - }; - cp0_i2c1_pins: i2c1-pins { - marvell,pins = "mpp35", "mpp36"; - marvell,function = "i2c1"; - }; - cp0_i2c0_pins: i2c0-pins { - marvell,pins = "mpp37", "mpp38"; - marvell,function = "i2c0"; - }; - cp0_uart1_pins: uart1-pins { - marvell,pins = "mpp40", "mpp41"; - marvell,function = "uart1"; - }; - cp0_xhci_vbus_pins: xhci0-vbus-pins { - marvell,pins = "mpp47"; - marvell,function = "gpio"; - }; - cp0_sfp_1g_pins: sfp-1g-pins { - marvell,pins = "mpp51", "mpp53", "mpp54"; - marvell,function = "gpio"; - }; - cp0_pcie_pins: pcie-pins { - marvell,pins = "mpp52"; - marvell,function = "gpio"; - }; - cp0_sdhci_pins: sdhci-pins { - marvell,pins = "mpp55", "mpp56", "mpp57", "mpp58", "mpp59", - "mpp60", "mpp61"; - marvell,function = "sdio"; - }; - cp0_sfpp1_pins: sfpp1-pins { - marvell,pins = "mpp62"; - marvell,function = "gpio"; - }; }; &cp0_xmdio { @@ -243,46 +30,11 @@ }; }; -&cp0_ethernet { - status = "okay"; -}; - &cp0_eth0 { status = "okay"; /* Network PHY */ phy = <&phy0>; phy-mode = "10gbase-kr"; - /* Generic PHY, providing serdes lanes */ - phys = <&cp0_comphy4 0>; -}; - -&cp0_sata0 { - /* CPM Lane 0 - U29 */ - status = "okay"; -}; - -&cp0_sdhci0 { - /* U6 */ - broken-cd; - bus-width = <4>; - pinctrl-names = "default"; - pinctrl-0 = <&cp0_sdhci_pins>; - status = "okay"; - vqmmc-supply = <&v_3_3>; -}; - -&cp0_usb3_0 { - /* J38? - USB2.0 only */ - status = "okay"; -}; - -&cp0_usb3_1 { - /* J38? - USB2.0 only */ - status = "okay"; -}; - -&cp1_ethernet { - status = "okay"; }; &cp1_eth0 { @@ -290,81 +42,4 @@ /* Network PHY */ phy = <&phy8>; phy-mode = "10gbase-kr"; - /* Generic PHY, providing serdes lanes */ - phys = <&cp1_comphy4 0>; -}; - -&cp1_eth1 { - /* CPS Lane 0 - J5 (Gigabit RJ45) */ - status = "okay"; - /* Network PHY */ - phy = <&ge_phy>; - phy-mode = "sgmii"; - /* Generic PHY, providing serdes lanes */ - phys = <&cp1_comphy0 1>; -}; - -&cp1_eth2 { - /* CPS Lane 5 */ - status = "okay"; - /* Network PHY */ - phy-mode = "2500base-x"; - managed = "in-band-status"; - /* Generic PHY, providing serdes lanes */ - phys = <&cp1_comphy5 2>; - sfp = <&sfp_eth3>; -}; - -&cp1_pinctrl { - cp1_sfpp1_pins: sfpp1-pins { - marvell,pins = "mpp8", "mpp10", "mpp11"; - marvell,function = "gpio"; - }; - cp1_spi1_pins: spi1-pins { - marvell,pins = "mpp12", "mpp13", "mpp14", "mpp15", "mpp16"; - marvell,function = "spi1"; - }; - cp1_uart0_pins: uart0-pins { - marvell,pins = "mpp6", "mpp7"; - marvell,function = "uart0"; - }; - cp1_sfp_1g_pins: sfp-1g-pins { - marvell,pins = "mpp24"; - marvell,function = "gpio"; - }; - cp1_sfpp0_pins: sfpp0-pins { - marvell,pins = "mpp26", "mpp27", "mpp28", "mpp29"; - marvell,function = "gpio"; - }; -}; - -/* J27 UART header */ -&cp1_uart0 { - pinctrl-names = "default"; - pinctrl-0 = <&cp1_uart0_pins>; - status = "okay"; -}; - -&cp1_sata0 { - /* CPS Lane 1 - U32 */ - /* CPS Lane 3 - U31 */ - status = "okay"; -}; - -&cp1_spi1 { - pinctrl-names = "default"; - pinctrl-0 = <&cp1_spi1_pins>; - status = "okay"; - - spi-flash@0 { - compatible = "st,w25q32"; - spi-max-frequency = <50000000>; - reg = <0>; - }; -}; - -&cp1_usb3_0 { - /* CPS Lane 2 - CON7 */ - usb-phy = <&usb3h0_phy>; - status = "okay"; }; diff --git a/arch/arm64/boot/dts/marvell/armada-8040-mcbin.dtsi b/arch/arm64/boot/dts/marvell/armada-8040-mcbin.dtsi new file mode 100644 index 000000000000..29ea7e81ec4c --- /dev/null +++ b/arch/arm64/boot/dts/marvell/armada-8040-mcbin.dtsi @@ -0,0 +1,346 @@ +// SPDX-License-Identifier: (GPL-2.0+ OR MIT) +/* + * Copyright (C) 2016 Marvell Technology Group Ltd. + * + * Device Tree file for MACCHIATOBin Armada 8040 community board platform + */ + +#include "armada-8040.dtsi" + +#include <dt-bindings/gpio/gpio.h> + +/ { + model = "Marvell 8040 MACCHIATOBin"; + compatible = "marvell,armada8040-mcbin", "marvell,armada8040", + "marvell,armada-ap806-quad", "marvell,armada-ap806"; + + chosen { + stdout-path = "serial0:115200n8"; + }; + + memory@0 { + device_type = "memory"; + reg = <0x0 0x0 0x0 0x80000000>; + }; + + aliases { + ethernet0 = &cp0_eth0; + ethernet1 = &cp1_eth0; + ethernet2 = &cp1_eth1; + ethernet3 = &cp1_eth2; + }; + + /* Regulator labels correspond with schematics */ + v_3_3: regulator-3-3v { + compatible = "regulator-fixed"; + regulator-name = "v_3_3"; + regulator-min-microvolt = <3300000>; + regulator-max-microvolt = <3300000>; + regulator-always-on; + status = "okay"; + }; + + v_vddo_h: regulator-1-8v { + compatible = "regulator-fixed"; + regulator-name = "v_vddo_h"; + regulator-min-microvolt = <1800000>; + regulator-max-microvolt = <1800000>; + regulator-always-on; + status = "okay"; + }; + + v_5v0_usb3_hst_vbus: regulator-usb3-vbus0 { + compatible = "regulator-fixed"; + enable-active-high; + gpio = <&cp0_gpio2 15 GPIO_ACTIVE_HIGH>; + pinctrl-names = "default"; + pinctrl-0 = <&cp0_xhci_vbus_pins>; + regulator-name = "v_5v0_usb3_hst_vbus"; + regulator-min-microvolt = <5000000>; + regulator-max-microvolt = <5000000>; + status = "okay"; + }; + + usb3h0_phy: usb3_phy0 { + compatible = "usb-nop-xceiv"; + vcc-supply = <&v_5v0_usb3_hst_vbus>; + }; + + sfp_eth0: sfp-eth0 { + /* CON15,16 - CPM lane 4 */ + compatible = "sff,sfp"; + i2c-bus = <&sfpp0_i2c>; + los-gpio = <&cp1_gpio1 28 GPIO_ACTIVE_HIGH>; + mod-def0-gpio = <&cp1_gpio1 27 GPIO_ACTIVE_LOW>; + tx-disable-gpio = <&cp1_gpio1 29 GPIO_ACTIVE_HIGH>; + tx-fault-gpio = <&cp1_gpio1 26 GPIO_ACTIVE_HIGH>; + pinctrl-names = "default"; + pinctrl-0 = <&cp1_sfpp0_pins>; + }; + + sfp_eth1: sfp-eth1 { + /* CON17,18 - CPS lane 4 */ + compatible = "sff,sfp"; + i2c-bus = <&sfpp1_i2c>; + los-gpio = <&cp1_gpio1 8 GPIO_ACTIVE_HIGH>; + mod-def0-gpio = <&cp1_gpio1 11 GPIO_ACTIVE_LOW>; + tx-disable-gpio = <&cp1_gpio1 10 GPIO_ACTIVE_HIGH>; + tx-fault-gpio = <&cp0_gpio2 30 GPIO_ACTIVE_HIGH>; + pinctrl-names = "default"; + pinctrl-0 = <&cp1_sfpp1_pins &cp0_sfpp1_pins>; + }; + + sfp_eth3: sfp-eth3 { + /* CON13,14 - CPS lane 5 */ + compatible = "sff,sfp"; + i2c-bus = <&sfp_1g_i2c>; + los-gpio = <&cp0_gpio2 22 GPIO_ACTIVE_HIGH>; + mod-def0-gpio = <&cp0_gpio2 21 GPIO_ACTIVE_LOW>; + tx-disable-gpio = <&cp1_gpio1 24 GPIO_ACTIVE_HIGH>; + tx-fault-gpio = <&cp0_gpio2 19 GPIO_ACTIVE_HIGH>; + pinctrl-names = "default"; + pinctrl-0 = <&cp0_sfp_1g_pins &cp1_sfp_1g_pins>; + }; +}; + +&uart0 { + status = "okay"; + pinctrl-0 = <&uart0_pins>; + pinctrl-names = "default"; +}; + +&ap_sdhci0 { + bus-width = <8>; + /* + * Not stable in HS modes - phy needs "more calibration", so add + * the "slow-mode" and disable SDR104, SDR50 and DDR50 modes. + */ + marvell,xenon-phy-slow-mode; + no-1-8-v; + no-sd; + no-sdio; + non-removable; + status = "okay"; + vqmmc-supply = <&v_vddo_h>; +}; + +&cp0_i2c0 { + clock-frequency = <100000>; + pinctrl-names = "default"; + pinctrl-0 = <&cp0_i2c0_pins>; + status = "okay"; +}; + +&cp0_i2c1 { + clock-frequency = <100000>; + pinctrl-names = "default"; + pinctrl-0 = <&cp0_i2c1_pins>; + status = "okay"; + + i2c-switch@70 { + compatible = "nxp,pca9548"; + #address-cells = <1>; + #size-cells = <0>; + reg = <0x70>; + + sfpp0_i2c: i2c@0 { + #address-cells = <1>; + #size-cells = <0>; + reg = <0>; + }; + sfpp1_i2c: i2c@1 { + #address-cells = <1>; + #size-cells = <0>; + reg = <1>; + }; + sfp_1g_i2c: i2c@2 { + #address-cells = <1>; + #size-cells = <0>; + reg = <2>; + }; + }; +}; + +/* J25 UART header */ +&cp0_uart1 { + pinctrl-names = "default"; + pinctrl-0 = <&cp0_uart1_pins>; + status = "okay"; +}; + +&cp0_mdio { + pinctrl-names = "default"; + pinctrl-0 = <&cp0_ge_mdio_pins>; + status = "okay"; + + ge_phy: ethernet-phy@0 { + reg = <0>; + }; +}; + +&cp0_pcie0 { + pinctrl-names = "default"; + pinctrl-0 = <&cp0_pcie_pins>; + num-lanes = <4>; + num-viewport = <8>; + reset-gpio = <&cp0_gpio1 20 GPIO_ACTIVE_LOW>; + status = "okay"; +}; + +&cp0_pinctrl { + cp0_ge_mdio_pins: ge-mdio-pins { + marvell,pins = "mpp32", "mpp34"; + marvell,function = "ge"; + }; + cp0_i2c1_pins: i2c1-pins { + marvell,pins = "mpp35", "mpp36"; + marvell,function = "i2c1"; + }; + cp0_i2c0_pins: i2c0-pins { + marvell,pins = "mpp37", "mpp38"; + marvell,function = "i2c0"; + }; + cp0_uart1_pins: uart1-pins { + marvell,pins = "mpp40", "mpp41"; + marvell,function = "uart1"; + }; + cp0_xhci_vbus_pins: xhci0-vbus-pins { + marvell,pins = "mpp47"; + marvell,function = "gpio"; + }; + cp0_sfp_1g_pins: sfp-1g-pins { + marvell,pins = "mpp51", "mpp53", "mpp54"; + marvell,function = "gpio"; + }; + cp0_pcie_pins: pcie-pins { + marvell,pins = "mpp52"; + marvell,function = "gpio"; + }; + cp0_sdhci_pins: sdhci-pins { + marvell,pins = "mpp55", "mpp56", "mpp57", "mpp58", "mpp59", + "mpp60", "mpp61"; + marvell,function = "sdio"; + }; + cp0_sfpp1_pins: sfpp1-pins { + marvell,pins = "mpp62"; + marvell,function = "gpio"; + }; +}; + +&cp0_ethernet { + status = "okay"; +}; + +&cp0_eth0 { + /* Generic PHY, providing serdes lanes */ + phys = <&cp0_comphy4 0>; +}; + +&cp0_sata0 { + /* CPM Lane 0 - U29 */ + status = "okay"; +}; + +&cp0_sdhci0 { + /* U6 */ + broken-cd; + bus-width = <4>; + pinctrl-names = "default"; + pinctrl-0 = <&cp0_sdhci_pins>; + status = "okay"; + vqmmc-supply = <&v_3_3>; +}; + +&cp0_usb3_0 { + /* J38? - USB2.0 only */ + status = "okay"; +}; + +&cp0_usb3_1 { + /* J38? - USB2.0 only */ + status = "okay"; +}; + +&cp1_ethernet { + status = "okay"; +}; + +&cp1_eth0 { + /* Generic PHY, providing serdes lanes */ + phys = <&cp1_comphy4 0>; +}; + +&cp1_eth1 { + /* CPS Lane 0 - J5 (Gigabit RJ45) */ + status = "okay"; + /* Network PHY */ + phy = <&ge_phy>; + phy-mode = "sgmii"; + /* Generic PHY, providing serdes lanes */ + phys = <&cp1_comphy0 1>; +}; + +&cp1_eth2 { + /* CPS Lane 5 */ + status = "okay"; + /* Network PHY */ + phy-mode = "2500base-x"; + managed = "in-band-status"; + /* Generic PHY, providing serdes lanes */ + phys = <&cp1_comphy5 2>; + sfp = <&sfp_eth3>; +}; + +&cp1_pinctrl { + cp1_sfpp1_pins: sfpp1-pins { + marvell,pins = "mpp8", "mpp10", "mpp11"; + marvell,function = "gpio"; + }; + cp1_spi1_pins: spi1-pins { + marvell,pins = "mpp12", "mpp13", "mpp14", "mpp15", "mpp16"; + marvell,function = "spi1"; + }; + cp1_uart0_pins: uart0-pins { + marvell,pins = "mpp6", "mpp7"; + marvell,function = "uart0"; + }; + cp1_sfp_1g_pins: sfp-1g-pins { + marvell,pins = "mpp24"; + marvell,function = "gpio"; + }; + cp1_sfpp0_pins: sfpp0-pins { + marvell,pins = "mpp26", "mpp27", "mpp28", "mpp29"; + marvell,function = "gpio"; + }; +}; + +/* J27 UART header */ +&cp1_uart0 { + pinctrl-names = "default"; + pinctrl-0 = <&cp1_uart0_pins>; + status = "okay"; +}; + +&cp1_sata0 { + /* CPS Lane 1 - U32 */ + /* CPS Lane 3 - U31 */ + status = "okay"; +}; + +&cp1_spi1 { + pinctrl-names = "default"; + pinctrl-0 = <&cp1_spi1_pins>; + status = "okay"; + + spi-flash@0 { + compatible = "st,w25q32"; + spi-max-frequency = <50000000>; + reg = <0>; + }; +}; + +&cp1_usb3_0 { + /* CPS Lane 2 - CON7 */ + usb-phy = <&usb3h0_phy>; + status = "okay"; +}; |