diff options
Diffstat (limited to 'Documentation')
5 files changed, 156 insertions, 11 deletions
diff --git a/Documentation/devicetree/bindings/pci/amlogic,meson-pcie.txt b/Documentation/devicetree/bindings/pci/amlogic,meson-pcie.txt new file mode 100644 index 000000000000..12b18f82d441 --- /dev/null +++ b/Documentation/devicetree/bindings/pci/amlogic,meson-pcie.txt @@ -0,0 +1,70 @@ +Amlogic Meson AXG DWC PCIE SoC controller + +Amlogic Meson PCIe host controller is based on the Synopsys DesignWare PCI core. +It shares common functions with the PCIe DesignWare core driver and +inherits common properties defined in +Documentation/devicetree/bindings/pci/designware-pci.txt. + +Additional properties are described here: + +Required properties: +- compatible: + should contain "amlogic,axg-pcie" to identify the core. +- reg: + should contain the configuration address space. +- reg-names: Must be + - "elbi" External local bus interface registers + - "cfg" Meson specific registers + - "phy" Meson PCIE PHY registers + - "config" PCIe configuration space +- reset-gpios: The GPIO to generate PCIe PERST# assert and deassert signal. +- clocks: Must contain an entry for each entry in clock-names. +- clock-names: Must include the following entries: + - "pclk" PCIe GEN 100M PLL clock + - "port" PCIe_x(A or B) RC clock gate + - "general" PCIe Phy clock + - "mipi" PCIe_x(A or B) 100M ref clock gate +- resets: phandle to the reset lines. +- reset-names: must contain "phy" "port" and "apb" + - "phy" Share PHY reset + - "port" Port A or B reset + - "apb" Share APB reset +- device_type: + should be "pci". As specified in designware-pcie.txt + + +Example configuration: + + pcie: pcie@f9800000 { + compatible = "amlogic,axg-pcie", "snps,dw-pcie"; + reg = <0x0 0xf9800000 0x0 0x400000 + 0x0 0xff646000 0x0 0x2000 + 0x0 0xff644000 0x0 0x2000 + 0x0 0xf9f00000 0x0 0x100000>; + reg-names = "elbi", "cfg", "phy", "config"; + reset-gpios = <&gpio GPIOX_19 GPIO_ACTIVE_HIGH>; + interrupts = <GIC_SPI 177 IRQ_TYPE_EDGE_RISING>; + #interrupt-cells = <1>; + interrupt-map-mask = <0 0 0 0>; + interrupt-map = <0 0 0 0 &gic GIC_SPI 179 IRQ_TYPE_EDGE_RISING>; + bus-range = <0x0 0xff>; + #address-cells = <3>; + #size-cells = <2>; + device_type = "pci"; + ranges = <0x82000000 0 0 0x0 0xf9c00000 0 0x00300000>; + + clocks = <&clkc CLKID_USB + &clkc CLKID_MIPI_ENABLE + &clkc CLKID_PCIE_A + &clkc CLKID_PCIE_CML_EN0>; + clock-names = "general", + "mipi", + "pclk", + "port"; + resets = <&reset RESET_PCIE_PHY>, + <&reset RESET_PCIE_A>, + <&reset RESET_PCIE_APB>; + reset-names = "phy", + "port", + "apb"; + }; diff --git a/Documentation/devicetree/bindings/pci/fsl,imx6q-pcie.txt b/Documentation/devicetree/bindings/pci/fsl,imx6q-pcie.txt index f37494d5a7be..d514c1f2365f 100644 --- a/Documentation/devicetree/bindings/pci/fsl,imx6q-pcie.txt +++ b/Documentation/devicetree/bindings/pci/fsl,imx6q-pcie.txt @@ -41,7 +41,9 @@ Optional properties: Additional required properties for imx6sx-pcie: - clock names: Must include the following additional entries: - "pcie_inbound_axi" -- power-domains: Must be set to a phandle pointing to the PCIE_PHY power domain +- power-domains: Must be set to phandles pointing to the DISPLAY and + PCIE_PHY power domains +- power-domain-names: Must be "pcie", "pcie_phy" Additional required properties for imx7d-pcie: - power-domains: Must be set to a phandle pointing to PCIE_PHY power domain diff --git a/Documentation/devicetree/bindings/pci/mediatek-pcie.txt b/Documentation/devicetree/bindings/pci/mediatek-pcie.txt index 20227a875ac8..92437a366e5f 100644 --- a/Documentation/devicetree/bindings/pci/mediatek-pcie.txt +++ b/Documentation/devicetree/bindings/pci/mediatek-pcie.txt @@ -65,7 +65,6 @@ Required properties: explanation. - ranges: Sub-ranges distributed from the PCIe controller node. An empty property is sufficient. -- num-lanes: Number of lanes to use for this port. Examples for MT7623: @@ -118,7 +117,6 @@ Examples for MT7623: interrupt-map-mask = <0 0 0 0>; interrupt-map = <0 0 0 0 &sysirq GIC_SPI 193 IRQ_TYPE_LEVEL_LOW>; ranges; - num-lanes = <1>; }; pcie@1,0 { @@ -129,7 +127,6 @@ Examples for MT7623: interrupt-map-mask = <0 0 0 0>; interrupt-map = <0 0 0 0 &sysirq GIC_SPI 194 IRQ_TYPE_LEVEL_LOW>; ranges; - num-lanes = <1>; }; pcie@2,0 { @@ -140,7 +137,6 @@ Examples for MT7623: interrupt-map-mask = <0 0 0 0>; interrupt-map = <0 0 0 0 &sysirq GIC_SPI 195 IRQ_TYPE_LEVEL_LOW>; ranges; - num-lanes = <1>; }; }; @@ -172,7 +168,6 @@ Examples for MT2712: #size-cells = <2>; #interrupt-cells = <1>; ranges; - num-lanes = <1>; interrupt-map-mask = <0 0 0 7>; interrupt-map = <0 0 0 1 &pcie_intc0 0>, <0 0 0 2 &pcie_intc0 1>, @@ -191,7 +186,6 @@ Examples for MT2712: #size-cells = <2>; #interrupt-cells = <1>; ranges; - num-lanes = <1>; interrupt-map-mask = <0 0 0 7>; interrupt-map = <0 0 0 1 &pcie_intc1 0>, <0 0 0 2 &pcie_intc1 1>, @@ -245,7 +239,6 @@ Examples for MT7622: #size-cells = <2>; #interrupt-cells = <1>; ranges; - num-lanes = <1>; interrupt-map-mask = <0 0 0 7>; interrupt-map = <0 0 0 1 &pcie_intc0 0>, <0 0 0 2 &pcie_intc0 1>, @@ -264,7 +257,6 @@ Examples for MT7622: #size-cells = <2>; #interrupt-cells = <1>; ranges; - num-lanes = <1>; interrupt-map-mask = <0 0 0 7>; interrupt-map = <0 0 0 1 &pcie_intc1 0>, <0 0 0 2 &pcie_intc1 1>, diff --git a/Documentation/devicetree/bindings/pci/uniphier-pcie.txt b/Documentation/devicetree/bindings/pci/uniphier-pcie.txt new file mode 100644 index 000000000000..1fa2c5906d4d --- /dev/null +++ b/Documentation/devicetree/bindings/pci/uniphier-pcie.txt @@ -0,0 +1,81 @@ +Socionext UniPhier PCIe host controller bindings + +This describes the devicetree bindings for PCIe host controller implemented +on Socionext UniPhier SoCs. + +UniPhier PCIe host controller is based on the Synopsys DesignWare PCI core. +It shares common functions with the PCIe DesignWare core driver and inherits +common properties defined in +Documentation/devicetree/bindings/pci/designware-pcie.txt. + +Required properties: +- compatible: Should be "socionext,uniphier-pcie". +- reg: Specifies offset and length of the register set for the device. + According to the reg-names, appropriate register sets are required. +- reg-names: Must include the following entries: + "dbi" - controller configuration registers + "link" - SoC-specific glue layer registers + "config" - PCIe configuration space +- clocks: A phandle to the clock gate for PCIe glue layer including + the host controller. +- resets: A phandle to the reset line for PCIe glue layer including + the host controller. +- interrupts: A list of interrupt specifiers. According to the + interrupt-names, appropriate interrupts are required. +- interrupt-names: Must include the following entries: + "dma" - DMA interrupt + "msi" - MSI interrupt + +Optional properties: +- phys: A phandle to generic PCIe PHY. According to the phy-names, appropriate + phys are required. +- phy-names: Must be "pcie-phy". + +Required sub-node: +- legacy-interrupt-controller: Specifies interrupt controller for legacy PCI + interrupts. + +Required properties for legacy-interrupt-controller: +- interrupt-controller: identifies the node as an interrupt controller. +- #interrupt-cells: specifies the number of cells needed to encode an + interrupt source. The value must be 1. +- interrupt-parent: Phandle to the parent interrupt controller. +- interrupts: An interrupt specifier for legacy interrupt. + +Example: + + pcie: pcie@66000000 { + compatible = "socionext,uniphier-pcie", "snps,dw-pcie"; + status = "disabled"; + reg-names = "dbi", "link", "config"; + reg = <0x66000000 0x1000>, <0x66010000 0x10000>, + <0x2fff0000 0x10000>; + #address-cells = <3>; + #size-cells = <2>; + clocks = <&sys_clk 24>; + resets = <&sys_rst 24>; + num-lanes = <1>; + num-viewport = <1>; + bus-range = <0x0 0xff>; + device_type = "pci"; + ranges = + /* downstream I/O */ + <0x81000000 0 0x00000000 0x2ffe0000 0 0x00010000 + /* non-prefetchable memory */ + 0x82000000 0 0x00000000 0x20000000 0 0x0ffe0000>; + #interrupt-cells = <1>; + interrupt-names = "dma", "msi"; + interrupts = <0 224 4>, <0 225 4>; + interrupt-map-mask = <0 0 0 7>; + interrupt-map = <0 0 0 1 &pcie_intc 0>, /* INTA */ + <0 0 0 2 &pcie_intc 1>, /* INTB */ + <0 0 0 3 &pcie_intc 2>, /* INTC */ + <0 0 0 4 &pcie_intc 3>; /* INTD */ + + pcie_intc: legacy-interrupt-controller { + interrupt-controller; + #interrupt-cells = <1>; + interrupt-parent = <&gic>; + interrupts = <0 226 4>; + }; + }; diff --git a/Documentation/driver-api/pci/p2pdma.rst b/Documentation/driver-api/pci/p2pdma.rst index 4c577fa7bef9..6d85b5a2598d 100644 --- a/Documentation/driver-api/pci/p2pdma.rst +++ b/Documentation/driver-api/pci/p2pdma.rst @@ -49,7 +49,7 @@ For example, in the NVMe Target Copy Offload implementation: in that it exposes any CMB (Controller Memory Buffer) as a P2P memory resource (provider), it accepts P2P memory pages as buffers in requests to be used directly (client) and it can also make use of the CMB as - submission queue entries (orchastrator). + submission queue entries (orchestrator). * The RDMA driver is a client in this arrangement so that an RNIC can DMA directly to the memory exposed by the NVMe device. * The NVMe Target driver (nvmet) can orchestrate the data from the RNIC @@ -111,7 +111,7 @@ that's compatible with all clients using :c:func:`pci_p2pmem_find()`. If more than one provider is supported, the one nearest to all the clients will be chosen first. If more than one provider is an equal distance away, the one returned will be chosen at random (it is not an arbitrary but -truely random). This function returns the PCI device to use for the provider +truly random). This function returns the PCI device to use for the provider with a reference taken and therefore when it's no longer needed it should be returned with pci_dev_put(). |