Merge tag 'pci-v6.13-changes' of git://git.kernel.org/pub/scm/linux/kernel/git/pci/pci

Pull PCI updates from Bjorn Helgaas:
 "Enumeration:

   - Make pci_stop_dev() and pci_destroy_dev() safe so concurrent
     callers can't stop a device multiple times, even as we migrate from
     the global pci_rescan_remove_lock to finer-grained locking (Keith
     Busch)

   - Improve pci_walk_bus() implementation by making it recursive and
     moving locking up to avoid need for a 'locked' parameter (Keith
     Busch)

   - Unexport pci_walk_bus_locked(), which is only used internally by
     the PCI core (Keith Busch)

   - Detect some Thunderbolt chips that are built-in and hence
     'trustworthy' by a heuristic since the 'ExternalFacingPort' and
     'usb4-host-interface' ACPI properties are not quite enough (Esther
     Shimanovich)

  Resource management:

   - Use PCI bus addresses (not CPU addresses) in 'ranges' properties
     when building dynamic DT nodes so systems where PCI and CPU
     addresses differ work correctly (Andrea della Porta)

   - Tidy resource sizing and assignment with helpers to reduce
     redundancy (Ilpo Järvinen)

   - Improve pdev_sort_resources() 'bogus alignment' warning to be more
     specific (Ilpo Järvinen)

  Driver binding:

   - Convert driver .remove_new() callbacks to .remove() again to finish
     the conversion from returning 'int' to being 'void' (Sergio
     Paracuellos)

   - Export pcim_request_all_regions(), a managed interface to request
     all BARs (Philipp Stanner)

   - Replace pcim_iomap_regions_request_all() with
     pcim_request_all_regions(), and pcim_iomap_table()[n] with
     pcim_iomap(n), in the following drivers: ahci, crypto qat, crypto
     octeontx2, intel_th, iwlwifi, ntb idt, serial rp2, ALSA korg1212
     (Philipp Stanner)

   - Remove the now unused pcim_iomap_regions_request_all() (Philipp
     Stanner)

   - Export pcim_iounmap_region(), a managed interface to unmap and
     release a PCI BAR (Philipp Stanner)

   - Replace pcim_iomap_regions(mask) with pcim_iomap_region(n), and
     pcim_iounmap_regions(mask) with pcim_iounmap_region(n), in the
     following drivers: fpga dfl-pci, block mtip32xx, gpio-merrifield,
     cavium (Philipp Stanner)

  Error handling:

   - Add sysfs 'reset_subordinate' to reset the entire hierarchy below a
     bridge; previously Secondary Bus Reset could only be used when
     there was a single device below a bridge (Keith Busch)

   - Warn if we reset a running device where the driver didn't register
     pci_error_handlers notification callbacks (Keith Busch)

  ASPM:

   - Disable ASPM L1 before touching L1 PM Substates to follow the spec
     closer and avoid a CPU load timeout on some platforms (Ajay
     Agarwal)

   - Set devices below Intel VMD to D0 before enabling ASPM L1 Substates
     as required per spec for all L1 Substates changes (Jian-Hong Pan)

  Power management:

   - Enable starfive controller runtime PM before probing host bridge
     (Mayank Rana)

   - Enable runtime power management for host bridges (Krishna chaitanya
     chundru)

  Power control:

   - Use of_platform_device_create() instead of of_platform_populate()
     to create pwrctl platform devices so we can control it based on the
     child nodes (Manivannan Sadhasivam)

   - Create pwrctrl platform devices only if there's a relevant power
     supply property (Manivannan Sadhasivam)

   - Add device link from the pwrctl supplier to the PCI dev to ensure
     pwrctl drivers are probed before the PCI dev driver; this avoids a
     race where pwrctl could change device power state while the PCI
     driver was active (Manivannan Sadhasivam)

   - Find pwrctl device for removal with of_find_device_by_node()
     instead of searching all children of the parent (Manivannan
     Sadhasivam)

   - Rename 'pwrctl' to 'pwrctrl' to match new bandwidth controller
     ('bwctrl') and hotplug files (Bjorn Helgaas)

  Bandwidth control:

   - Add read/modify/write locking for Link Control 2, which is used to
     manage Link speed (Ilpo Järvinen)

   - Extract Link Bandwidth Management Status check into
     pcie_lbms_seen(), where it can be shared between the bandwidth
     controller and quirks that use it to help retrain failed links
     (Ilpo Järvinen)

   - Re-add Link Bandwidth notification support with updates to address
     the reasons it was previously reverted (Alexandru Gagniuc, Ilpo
     Järvinen)

   - Add pcie_set_target_speed() and related functionality so drivers
     can manage PCIe Link speed based on thermal or other constraints
     (Ilpo Järvinen)

   - Add a thermal cooling driver to throttle PCIe Links via the
     existing thermal management framework (Ilpo Järvinen)

   - Add a userspace selftest for the PCIe bandwidth controller (Ilpo
     Järvinen)

  PCI device hotplug:

   - Add hotplug controller driver for Marvell OCTEON multi-function
     device where function 0 has a management console interface to
     enable/disable and provision various personalities for the other
     functions (Shijith Thotton)

   - Retain a reference to the pci_bus for the lifetime of a pci_slot to
     avoid a use-after-free when the thunderbolt driver resets USB4 host
     routers on boot, causing hotplug remove/add of downstream docks or
     other devices (Lukas Wunner)

   - Remove unused cpcihp struct cpci_hp_controller_ops.hardware_test
     (Guilherme Giacomo Simoes)

   - Remove unused cpqphp struct ctrl_dbg.ctrl (Christophe JAILLET)

   - Use pci_bus_read_dev_vendor_id() instead of hand-coded presence
     detection in cpqphp (Ilpo Järvinen)

   - Simplify cpqphp enumeration, which is already simple-minded and
     doesn't handle devices below hot-added bridges (Ilpo Järvinen)

  Virtualization:

   - Add ACS quirk for Wangxun FF5xxx NICs, which don't advertise an ACS
     capability but do isolate functions as though PCI_ACS_RR and
     PCI_ACS_CR were set, so the functions can be in independent IOMMU
     groups (Mengyuan Lou)

  TLP Processing Hints (TPH):

   - Add and document TLP Processing Hints (TPH) support so drivers can
     enable and disable TPH and the kernel can save/restore TPH
     configuration (Wei Huang)

   - Add TPH Steering Tag support so drivers can retrieve Steering Tag
     values associated with specific CPUs via an ACPI _DSM to improve
     performance by directing DMA writes closer to their consumers (Wei
     Huang)

  Data Object Exchange (DOE):

   - Wait up to 1 second for DOE Busy bit to clear before writing a
     request to the mailbox to avoid failures if the mailbox is still
     busy from a previous transfer (Gregory Price)

  Endpoint framework:

   - Skip attempts to allocate from endpoint controller memory window if
     the requested size is larger than the window (Damien Le Moal)

   - Add and document pci_epc_mem_map() and pci_epc_mem_unmap() to
     handle controller-specific size and alignment constraints, and add
     test cases to the endpoint test driver (Damien Le Moal)

   - Implement dwc pci_epc_ops.align_addr() so pci_epc_mem_map() can
     observe DWC-specific alignment requirements (Damien Le Moal)

   - Synchronously cancel command handler work in endpoint test before
     cleaning up DMA and BARs (Damien Le Moal)

   - Respect endpoint page size in dw_pcie_ep_align_addr() (Niklas
     Cassel)

   - Use dw_pcie_ep_align_addr() in dw_pcie_ep_raise_msi_irq() and
     dw_pcie_ep_raise_msix_irq() instead of open coding the equivalent
     (Niklas Cassel)

   - Avoid NULL dereference if Modem Host Interface Endpoint lacks
     'mmio' DT property (Zhongqiu Han)

   - Release PCI domain ID of Endpoint controller parent (not controller
     itself) and before unregistering the controller, to avoid
     use-after-free (Zijun Hu)

   - Clear secondary (not primary) EPC in pci_epc_remove_epf() when
     removing the secondary controller associated with an NTB (Zijun Hu)

  Cadence PCIe controller driver:

   - Lower severity of 'phy-names' message (Bartosz Wawrzyniak)

  Freescale i.MX6 PCIe controller driver:

   - Fix suspend/resume support on i.MX6QDL, which has a hardware
     erratum that prevents use of L2 (Stefan Eichenberger)

  Intel VMD host bridge driver:

   - Add 0xb60b and 0xb06f Device IDs for client SKUs (Nirmal Patel)

  MediaTek PCIe Gen3 controller driver:

   - Update mediatek-gen3 DT binding to require the exact number of
     clocks for each SoC (Fei Shao)

   - Add support for DT 'max-link-speed' and 'num-lanes' properties to
     restrict the link speed and width (AngeloGioacchino Del Regno)

  Microchip PolarFlare PCIe controller driver:

   - Add DT and driver support for using either of the two PolarFire
     Root Ports (Conor Dooley)

  NVIDIA Tegra194 PCIe controller driver:

   - Move endpoint controller cleanups that depend on refclk from the
     host to the notifier that tells us the host has deasserted PERST#,
     when refclk should be valid (Manivannan Sadhasivam)

  Qualcomm PCIe controller driver:

   - Add qcom SAR2130P DT binding with an additional clock (Dmitry
     Baryshkov)

   - Enable MSI interrupts if 'global' IRQ is supported, since a
     previous commit unintentionally masked them (Manivannan Sadhasivam)

   - Move endpoint controller cleanups that depend on refclk from the
     host to the notifier that tells us the host has deasserted PERST#,
     when refclk should be valid (Manivannan Sadhasivam)

   - Add DT binding and driver support for IPQ9574, with Synopsys IP
     v5.80a and Qcom IP 1.27.0 (devi priya)

   - Move the OPP "operating-points-v2" table from the
     qcom,pcie-sm8450.yaml DT binding to qcom,pcie-common.yaml, where it
     can be used by other Qcom platforms (Qiang Yu)

   - Add 'global' SPI interrupt for events like link-up, link-down to
     qcom,pcie-x1e80100 DT binding so we can start enumeration when the
     link comes up (Qiang Yu)

   - Disable ASPM L0s for qcom,pcie-x1e80100 since the PHY is not tuned
     to support this (Qiang Yu)

   - Add ops_1_21_0 for SC8280X family SoC, which doesn't use the
     'iommu-map' DT property and doesn't need BDF-to-SID translation
     (Qiang Yu)

  Rockchip PCIe controller driver:

   - Define ROCKCHIP_PCIE_AT_SIZE_ALIGN to replace magic 256 endpoint
     .align value (Damien Le Moal)

   - When unmapping an endpoint window, compute the region index instead
     of searching for it, and verify that the address was mapped (Damien
     Le Moal)

   - When mapping an endpoint window, verify that the address hasn't
     been mapped already (Damien Le Moal)

   - Implement pci_epc_ops.align_addr() for rockchip-ep (Damien Le Moal)

   - Fix MSI IRQ data mapping to observe the alignment constraint, which
     fixes intermittent page faults in memcpy_toio() and memcpy_fromio()
     (Damien Le Moal)

   - Rename rockchip_pcie_parse_ep_dt() to
     rockchip_pcie_ep_get_resources() for consistency with similar DT
     interfaces (Damien Le Moal)

   - Skip the unnecessary link train in rockchip_pcie_ep_probe() and do
     it only in the endpoint start operation (Damien Le Moal)

   - Implement pci_epc_ops.stop_link() to disable link training and
     controller configuration (Damien Le Moal)

   - Attempt link training at 5 GT/s when both partners support it
     (Damien Le Moal)

   - Add a handler for PERST# signal so we can detect host-initiated
     resets and start link training after PERST# is deasserted (Damien
     Le Moal)

  Synopsys DesignWare PCIe controller driver:

   - Clear outbound address on unmap so dw_pcie_find_index() won't match
     an ATU index that was already unmapped (Damien Le Moal)

   - Use of_property_present() instead of of_property_read_bool() when
     testing for presence of non-boolean DT properties (Rob Herring)

   - Advertise 1MB size if endpoint supports Resizable BARs, which was
     inadvertently lost in v6.11 (Niklas Cassel)

  TI J721E PCIe driver:

   - Add PCIe support for J722S SoC (Siddharth Vadapalli)

   - Delay PCIE_T_PVPERL_MS (100 ms), not just PCIE_T_PERST_CLK_US (100
     us), before deasserting PERST# to ensure power and refclk are
     stable (Siddharth Vadapalli)

  TI Keystone PCIe controller driver:

   - Set the 'ti,keystone-pcie' mode so v3.65a devices work in Root
     Complex mode (Kishon Vijay Abraham I)

   - Try to avoid unrecoverable SError for attempts to issue config
     transactions when the link is down; this is racy but the best we
     can do (Kishon Vijay Abraham I)

  Miscellaneous:

   - Reorganize kerneldoc parameter names to match order in function
     signature (Julia Lawall)

   - Fix sysfs reset_method_store() memory leak (Todd Kjos)

   - Simplify pci_create_slot() (Ilpo Järvinen)

   - Fix incorrect printf format specifiers in pcitest (Luo Yifan)"

* tag 'pci-v6.13-changes' of git://git.kernel.org/pub/scm/linux/kernel/git/pci/pci: (127 commits)
  PCI: rockchip-ep: Handle PERST# signal in EP mode
  PCI: rockchip-ep: Improve link training
  PCI: rockship-ep: Implement the pci_epc_ops::stop_link() operation
  PCI: rockchip-ep: Refactor endpoint link training enable
  PCI: rockchip-ep: Refactor rockchip_pcie_ep_probe() MSI-X hiding
  PCI: rockchip-ep: Refactor rockchip_pcie_ep_probe() memory allocations
  PCI: rockchip-ep: Rename rockchip_pcie_parse_ep_dt()
  PCI: rockchip-ep: Fix MSI IRQ data mapping
  PCI: rockchip-ep: Implement the pci_epc_ops::align_addr() operation
  PCI: rockchip-ep: Improve rockchip_pcie_ep_map_addr()
  PCI: rockchip-ep: Improve rockchip_pcie_ep_unmap_addr()
  PCI: rockchip-ep: Use a macro to define EP controller .align feature
  PCI: rockchip-ep: Fix address translation unit programming
  PCI/pwrctrl: Rename pwrctrl functions and structures
  PCI/pwrctrl: Rename pwrctl files to pwrctrl
  PCI/pwrctl: Remove pwrctl device without iterating over all children of pwrctl parent
  PCI/pwrctl: Ensure that pwrctl drivers are probed before PCI client drivers
  PCI/pwrctl: Create pwrctl device only if at least one power supply is present
  PCI/pwrctl: Use of_platform_device_create() to create pwrctl devices
  tools: PCI: Fix incorrect printf format specifiers
  ...

3 files changed, 91 insertions, 0 deletions

diff --git a/drivers/thermal/Kconfig b/drivers/thermal/Kconfig
index 61e7ae524b1f..d3f9686e26e7 100644
--- a/drivers/thermal/Kconfig
+++ b/drivers/thermal/Kconfig
@@ -220,6 +220,15 @@ config DEVFREQ_THERMAL
 
 	  If you want this support, you should say Y here.
 
+config PCIE_THERMAL
+	bool "PCIe cooling support"
+	depends on PCIEPORTBUS
+	help
+	  This implements PCIe cooling mechanism through bandwidth reduction
+	  for PCIe devices.
+
+	  If you want this support, you should say Y here.
+
 config THERMAL_EMULATION
 	bool "Thermal emulation mode support"
 	help
diff --git a/drivers/thermal/Makefile b/drivers/thermal/Makefile
index 1e1559bb971e..9abf43a74f2b 100644
--- a/drivers/thermal/Makefile
+++ b/drivers/thermal/Makefile
@@ -32,6 +32,8 @@ thermal_sys-$(CONFIG_CPU_IDLE_THERMAL)	+= cpuidle_cooling.o
 # devfreq cooling
 thermal_sys-$(CONFIG_DEVFREQ_THERMAL) += devfreq_cooling.o
 
+thermal_sys-$(CONFIG_PCIE_THERMAL) += pcie_cooling.o
+
 obj-$(CONFIG_K3_THERMAL)	+= k3_bandgap.o k3_j72xx_bandgap.o
 # platform thermal drivers
 obj-y				+= broadcom/
diff --git a/drivers/thermal/pcie_cooling.c b/drivers/thermal/pcie_cooling.c
new file mode 100644
index 000000000000..a876d64f1582
--- /dev/null
+++ b/drivers/thermal/pcie_cooling.c
@@ -0,0 +1,80 @@
+// SPDX-License-Identifier: GPL-2.0-only
+/*
+ * PCIe cooling device
+ *
+ * Copyright (C) 2023-2024 Intel Corporation
+ */
+
+#include <linux/build_bug.h>
+#include <linux/cleanup.h>
+#include <linux/err.h>
+#include <linux/module.h>
+#include <linux/pci.h>
+#include <linux/pci-bwctrl.h>
+#include <linux/slab.h>
+#include <linux/sprintf.h>
+#include <linux/thermal.h>
+
+#define COOLING_DEV_TYPE_PREFIX		"PCIe_Port_Link_Speed_"
+
+static int pcie_cooling_get_max_level(struct thermal_cooling_device *cdev, unsigned long *state)
+{
+	struct pci_dev *port = cdev->devdata;
+
+	/* cooling state 0 is same as the maximum PCIe speed */
+	*state = port->subordinate->max_bus_speed - PCIE_SPEED_2_5GT;
+
+	return 0;
+}
+
+static int pcie_cooling_get_cur_level(struct thermal_cooling_device *cdev, unsigned long *state)
+{
+	struct pci_dev *port = cdev->devdata;
+
+	/* cooling state 0 is same as the maximum PCIe speed */
+	*state = cdev->max_state - (port->subordinate->cur_bus_speed - PCIE_SPEED_2_5GT);
+
+	return 0;
+}
+
+static int pcie_cooling_set_cur_level(struct thermal_cooling_device *cdev, unsigned long state)
+{
+	struct pci_dev *port = cdev->devdata;
+	enum pci_bus_speed speed;
+
+	/* cooling state 0 is same as the maximum PCIe speed */
+	speed = (cdev->max_state - state) + PCIE_SPEED_2_5GT;
+
+	return pcie_set_target_speed(port, speed, true);
+}
+
+static struct thermal_cooling_device_ops pcie_cooling_ops = {
+	.get_max_state = pcie_cooling_get_max_level,
+	.get_cur_state = pcie_cooling_get_cur_level,
+	.set_cur_state = pcie_cooling_set_cur_level,
+};
+
+struct thermal_cooling_device *pcie_cooling_device_register(struct pci_dev *port)
+{
+	char *name __free(kfree) =
+		kasprintf(GFP_KERNEL, COOLING_DEV_TYPE_PREFIX "%s", pci_name(port));
+	if (!name)
+		return ERR_PTR(-ENOMEM);
+
+	return thermal_cooling_device_register(name, port, &pcie_cooling_ops);
+}
+
+void pcie_cooling_device_unregister(struct thermal_cooling_device *cdev)
+{
+	thermal_cooling_device_unregister(cdev);
+}
+
+/* For bus_speed <-> state arithmetic */
+static_assert(PCIE_SPEED_2_5GT + 1 == PCIE_SPEED_5_0GT);
+static_assert(PCIE_SPEED_5_0GT + 1 == PCIE_SPEED_8_0GT);
+static_assert(PCIE_SPEED_8_0GT + 1 == PCIE_SPEED_16_0GT);
+static_assert(PCIE_SPEED_16_0GT + 1 == PCIE_SPEED_32_0GT);
+static_assert(PCIE_SPEED_32_0GT + 1 == PCIE_SPEED_64_0GT);
+
+MODULE_AUTHOR("Ilpo Järvinen <ilpo.jarvinen@linux.intel.com>");
+MODULE_DESCRIPTION("PCIe cooling driver");