Merge branch 'v4l_for_linus' of git://git.kernel.org/pub/scm/linux/kernel/git/mchehab/linux-2.6

* 'v4l_for_linus' of git://git.kernel.org/pub/scm/linux/kernel/git/mchehab/linux-2.6: (430 commits)
  [media] ir-mce_kbd-decoder: include module.h for its facilities
  [media] ov5642: include module.h for its facilities
  [media] em28xx: Fix DVB-C maxsize for em2884
  [media] tda18271c2dd: Fix saw filter configuration for DVB-C @6MHz
  [media] v4l: mt9v032: Fix Bayer pattern
  [media] V4L: mt9m111: rewrite set_pixfmt
  [media] V4L: mt9m111: fix missing return value check mt9m111_reg_clear
  [media] V4L: initial driver for ov5642 CMOS sensor
  [media] V4L: sh_mobile_ceu_camera: fix Oops when USERPTR mapping fails
  [media] V4L: soc-camera: remove soc-camera bus and devices on it
  [media] V4L: soc-camera: un-export the soc-camera bus
  [media] V4L: sh_mobile_csi2: switch away from using the soc-camera bus notifier
  [media] V4L: add media bus configuration subdev operations
  [media] V4L: soc-camera: group struct field initialisations together
  [media] V4L: soc-camera: remove now unused soc-camera specific PM hooks
  [media] V4L: pxa-camera: switch to using standard PM hooks
  [media] NetUP Dual DVB-T/C CI RF: force card hardware revision by module param
  [media] Don't OOPS if videobuf_dvb_get_frontend return NULL
  [media] NetUP Dual DVB-T/C CI RF: load firmware according card revision
  [media] omap3isp: Support configurable HS/VS polarities
  ...

Fix up conflicts:
 - arch/arm/mach-omap2/board-rx51-peripherals.c:
     cleanup regulator supply definitions in mach-omap2
   vs
     OMAP3: RX-51: define vdds_csib regulator supply
 - drivers/staging/tm6000/tm6000-alsa.c (trivial)

4 files changed, 251 insertions, 101 deletions

diff --git a/drivers/staging/cxd2099/Kconfig b/drivers/staging/cxd2099/Kconfig
index 9d638c30735d..b48aefddc84c 100644
--- a/drivers/staging/cxd2099/Kconfig
+++ b/drivers/staging/cxd2099/Kconfig
@@ -1,9 +1,10 @@
 config DVB_CXD2099
-        tristate "CXD2099AR Common Interface driver"
-        depends on DVB_CORE && PCI && I2C && DVB_NGENE
-        ---help---
-          Support for the CI module found on cineS2 DVB-S2, supported by
-	  the Micronas PCIe device driver (ngene).
+	tristate "CXD2099AR Common Interface driver"
+	depends on DVB_CORE && PCI && I2C
+	---help---
+	  Support for the CI module found on cards based on
+	  - Micronas ngene PCIe bridge: cineS2 etc.
+	  - Digital Devices PCIe bridge: Octopus series
 
 	  For now, data is passed through '/dev/dvb/adapterX/sec0':
 	    - Encrypted data must be written to 'sec0'.
diff --git a/drivers/staging/cxd2099/cxd2099.c b/drivers/staging/cxd2099/cxd2099.c
index 55b1c4a59035..1c04185bcfd7 100644
--- a/drivers/staging/cxd2099/cxd2099.c
+++ b/drivers/staging/cxd2099/cxd2099.c
@@ -1,7 +1,7 @@
 /*
  * cxd2099.c: Driver for the CXD2099AR Common Interface Controller
  *
- * Copyright (C) 2010 DigitalDevices UG
+ * Copyright (C) 2010-2011 Digital Devices GmbH
  *
  *
  * This program is free software; you can redistribute it and/or
@@ -41,13 +41,13 @@ struct cxd {
 	struct dvb_ca_en50221 en;
 
 	struct i2c_adapter *i2c;
-	u8     adr;
+	struct cxd2099_cfg cfg;
+
 	u8     regs[0x23];
 	u8     lastaddress;
 	u8     clk_reg_f;
 	u8     clk_reg_b;
 	int    mode;
-	u32    bitrate;
 	int    ready;
 	int    dr;
 	int    slot_stat;
@@ -89,9 +89,9 @@ static int i2c_read_reg(struct i2c_adapter *adapter, u8 adr,
 			u8 reg, u8 *val)
 {
 	struct i2c_msg msgs[2] = {{.addr = adr, .flags = 0,
-				   .buf = &reg, .len = 1 },
+				   .buf = &reg, .len = 1},
 				  {.addr = adr, .flags = I2C_M_RD,
-				   .buf = val, .len = 1 } };
+				   .buf = val, .len = 1} };
 
 	if (i2c_transfer(adapter, msgs, 2) != 2) {
 		printk(KERN_ERR "error in i2c_read_reg\n");
@@ -104,9 +104,9 @@ static int i2c_read(struct i2c_adapter *adapter, u8 adr,
 		    u8 reg, u8 *data, u8 n)
 {
 	struct i2c_msg msgs[2] = {{.addr = adr, .flags = 0,
-				   .buf = &reg, .len = 1 },
-				  {.addr = adr, .flags = I2C_M_RD,
-				   .buf = data, .len = n } };
+				 .buf = &reg, .len = 1},
+				{.addr = adr, .flags = I2C_M_RD,
+				 .buf = data, .len = n} };
 
 	if (i2c_transfer(adapter, msgs, 2) != 2) {
 		printk(KERN_ERR "error in i2c_read\n");
@@ -119,10 +119,10 @@ static int read_block(struct cxd *ci, u8 adr, u8 *data, u8 n)
 {
 	int status;
 
-	status = i2c_write_reg(ci->i2c, ci->adr, 0, adr);
+	status = i2c_write_reg(ci->i2c, ci->cfg.adr, 0, adr);
 	if (!status) {
 		ci->lastaddress = adr;
-		status = i2c_read(ci->i2c, ci->adr, 1, data, n);
+		status = i2c_read(ci->i2c, ci->cfg.adr, 1, data, n);
 	}
 	return status;
 }
@@ -136,24 +136,24 @@ static int read_reg(struct cxd *ci, u8 reg, u8 *val)
 static int read_pccard(struct cxd *ci, u16 address, u8 *data, u8 n)
 {
 	int status;
-	u8 addr[3] = { 2, address&0xff, address>>8 };
+	u8 addr[3] = {2, address & 0xff, address >> 8};
 
-	status = i2c_write(ci->i2c, ci->adr, addr, 3);
+	status = i2c_write(ci->i2c, ci->cfg.adr, addr, 3);
 	if (!status)
-		status = i2c_read(ci->i2c, ci->adr, 3, data, n);
+		status = i2c_read(ci->i2c, ci->cfg.adr, 3, data, n);
 	return status;
 }
 
 static int write_pccard(struct cxd *ci, u16 address, u8 *data, u8 n)
 {
 	int status;
-	u8 addr[3] = { 2, address&0xff, address>>8 };
+	u8 addr[3] = {2, address & 0xff, address >> 8};
 
-	status = i2c_write(ci->i2c, ci->adr, addr, 3);
+	status = i2c_write(ci->i2c, ci->cfg.adr, addr, 3);
 	if (!status) {
 		u8 buf[256] = {3};
 		memcpy(buf+1, data, n);
-		status = i2c_write(ci->i2c, ci->adr, buf, n+1);
+		status = i2c_write(ci->i2c, ci->cfg.adr, buf, n+1);
 	}
 	return status;
 }
@@ -161,39 +161,64 @@ static int write_pccard(struct cxd *ci, u16 address, u8 *data, u8 n)
 static int read_io(struct cxd *ci, u16 address, u8 *val)
 {
 	int status;
-	u8 addr[3] = { 2, address&0xff, address>>8 };
+	u8 addr[3] = {2, address & 0xff, address >> 8};
 
-	status = i2c_write(ci->i2c, ci->adr, addr, 3);
+	status = i2c_write(ci->i2c, ci->cfg.adr, addr, 3);
 	if (!status)
-		status = i2c_read(ci->i2c, ci->adr, 3, val, 1);
+		status = i2c_read(ci->i2c, ci->cfg.adr, 3, val, 1);
 	return status;
 }
 
 static int write_io(struct cxd *ci, u16 address, u8 val)
 {
 	int status;
-	u8 addr[3] = { 2, address&0xff, address>>8 };
-	u8 buf[2] = { 3, val };
+	u8 addr[3] = {2, address & 0xff, address >> 8};
+	u8 buf[2] = {3, val};
 
-	status = i2c_write(ci->i2c, ci->adr, addr, 3);
+	status = i2c_write(ci->i2c, ci->cfg.adr, addr, 3);
 	if (!status)
-		status = i2c_write(ci->i2c, ci->adr, buf, 2);
-
+		status = i2c_write(ci->i2c, ci->cfg.adr, buf, 2);
 	return status;
 }
 
+#if 0
+static int read_io_data(struct cxd *ci, u8 *data, u8 n)
+{
+	int status;
+	u8 addr[3] = { 2, 0, 0 };
+
+	status = i2c_write(ci->i2c, ci->cfg.adr, addr, 3);
+	if (!status)
+		status = i2c_read(ci->i2c, ci->cfg.adr, 3, data, n);
+	return 0;
+}
+
+static int write_io_data(struct cxd *ci, u8 *data, u8 n)
+{
+	int status;
+	u8 addr[3] = {2, 0, 0};
+
+	status = i2c_write(ci->i2c, ci->cfg.adr, addr, 3);
+	if (!status) {
+		u8 buf[256] = {3};
+		memcpy(buf+1, data, n);
+		status = i2c_write(ci->i2c, ci->cfg.adr, buf, n + 1);
+	}
+	return 0;
+}
+#endif
 
 static int write_regm(struct cxd *ci, u8 reg, u8 val, u8 mask)
 {
 	int status;
 
-	status = i2c_write_reg(ci->i2c, ci->adr, 0, reg);
+	status = i2c_write_reg(ci->i2c, ci->cfg.adr, 0, reg);
 	if (!status && reg >= 6 && reg <= 8 && mask != 0xff)
-		status = i2c_read_reg(ci->i2c, ci->adr, 1, &ci->regs[reg]);
-	ci->regs[reg] = (ci->regs[reg]&(~mask))|val;
+		status = i2c_read_reg(ci->i2c, ci->cfg.adr, 1, &ci->regs[reg]);
+	ci->regs[reg] = (ci->regs[reg] & (~mask)) | val;
 	if (!status) {
 		ci->lastaddress = reg;
-		status = i2c_write_reg(ci->i2c, ci->adr, 1, ci->regs[reg]);
+		status = i2c_write_reg(ci->i2c, ci->cfg.adr, 1, ci->regs[reg]);
 	}
 	if (reg == 0x20)
 		ci->regs[reg] &= 0x7f;
@@ -211,11 +236,11 @@ static int write_block(struct cxd *ci, u8 adr, u8 *data, int n)
 	int status;
 	u8 buf[256] = {1};
 
-	status = i2c_write_reg(ci->i2c, ci->adr, 0, adr);
+	status = i2c_write_reg(ci->i2c, ci->cfg.adr, 0, adr);
 	if (!status) {
 		ci->lastaddress = adr;
-		memcpy(buf+1, data, n);
-		status = i2c_write(ci->i2c, ci->adr, buf, n+1);
+		memcpy(buf + 1, data, n);
+		status = i2c_write(ci->i2c, ci->cfg.adr, buf, n + 1);
 	}
 	return status;
 }
@@ -249,12 +274,16 @@ static void cam_mode(struct cxd *ci, int mode)
 		write_regm(ci, 0x20, 0x80, 0x80);
 		break;
 	case 0x01:
+#ifdef BUFFER_MODE
+		if (!ci->en.read_data)
+			return;
 		printk(KERN_INFO "enable cam buffer mode\n");
 		/* write_reg(ci, 0x0d, 0x00); */
 		/* write_reg(ci, 0x0e, 0x01); */
 		write_regm(ci, 0x08, 0x40, 0x40);
 		/* read_reg(ci, 0x12, &dummy); */
 		write_regm(ci, 0x08, 0x80, 0x80);
+#endif
 		break;
 	default:
 		break;
@@ -264,8 +293,6 @@ static void cam_mode(struct cxd *ci, int mode)
 
 
 
-#define CHK_ERROR(s) if ((status = s)) break
-
 static int init(struct cxd *ci)
 {
 	int status;
@@ -273,63 +300,160 @@ static int init(struct cxd *ci)
 	mutex_lock(&ci->lock);
 	ci->mode = -1;
 	do {
-		CHK_ERROR(write_reg(ci, 0x00, 0x00));
-		CHK_ERROR(write_reg(ci, 0x01, 0x00));
-		CHK_ERROR(write_reg(ci, 0x02, 0x10));
-		CHK_ERROR(write_reg(ci, 0x03, 0x00));
-		CHK_ERROR(write_reg(ci, 0x05, 0xFF));
-		CHK_ERROR(write_reg(ci, 0x06, 0x1F));
-		CHK_ERROR(write_reg(ci, 0x07, 0x1F));
-		CHK_ERROR(write_reg(ci, 0x08, 0x28));
-		CHK_ERROR(write_reg(ci, 0x14, 0x20));
-
-		CHK_ERROR(write_reg(ci, 0x09, 0x4D)); /* Input Mode C, BYPass Serial, TIVAL = low, MSB */
-		CHK_ERROR(write_reg(ci, 0x0A, 0xA7)); /* TOSTRT = 8, Mode B (gated clock), falling Edge, Serial, POL=HIGH, MSB */
-
-		/* Sync detector */
-		CHK_ERROR(write_reg(ci, 0x0B, 0x33));
-		CHK_ERROR(write_reg(ci, 0x0C, 0x33));
-
-		CHK_ERROR(write_regm(ci, 0x14, 0x00, 0x0F));
-		CHK_ERROR(write_reg(ci, 0x15, ci->clk_reg_b));
-		CHK_ERROR(write_regm(ci, 0x16, 0x00, 0x0F));
-		CHK_ERROR(write_reg(ci, 0x17, ci->clk_reg_f));
-
-		CHK_ERROR(write_reg(ci, 0x20, 0x28)); /* Integer Divider, Falling Edge, Internal Sync, */
-		CHK_ERROR(write_reg(ci, 0x21, 0x00)); /* MCLKI = TICLK/8 */
-		CHK_ERROR(write_reg(ci, 0x22, 0x07)); /* MCLKI = TICLK/8 */
-
-
-		CHK_ERROR(write_regm(ci, 0x20, 0x80, 0x80)); /* Reset CAM state machine */
-
-		CHK_ERROR(write_regm(ci, 0x03, 0x02, 02));  /* Enable IREQA Interrupt */
-		CHK_ERROR(write_reg(ci, 0x01, 0x04));  /* Enable CD Interrupt */
-		CHK_ERROR(write_reg(ci, 0x00, 0x31));  /* Enable TS1,Hot Swap,Slot A */
-		CHK_ERROR(write_regm(ci, 0x09, 0x08, 0x08));  /* Put TS in bypass */
+		status = write_reg(ci, 0x00, 0x00);
+		if (status < 0)
+			break;
+		status = write_reg(ci, 0x01, 0x00);
+		if (status < 0)
+			break;
+		status = write_reg(ci, 0x02, 0x10);
+		if (status < 0)
+			break;
+		status = write_reg(ci, 0x03, 0x00);
+		if (status < 0)
+			break;
+		status = write_reg(ci, 0x05, 0xFF);
+		if (status < 0)
+			break;
+		status = write_reg(ci, 0x06, 0x1F);
+		if (status < 0)
+			break;
+		status = write_reg(ci, 0x07, 0x1F);
+		if (status < 0)
+			break;
+		status = write_reg(ci, 0x08, 0x28);
+		if (status < 0)
+			break;
+		status = write_reg(ci, 0x14, 0x20);
+		if (status < 0)
+			break;
+
+#if 0
+		status = write_reg(ci, 0x09, 0x4D); /* Input Mode C, BYPass Serial, TIVAL = low, MSB */
+		if (status < 0)
+			break;
+#endif
+		status = write_reg(ci, 0x0A, 0xA7); /* TOSTRT = 8, Mode B (gated clock), falling Edge, Serial, POL=HIGH, MSB */
+		if (status < 0)
+			break;
+
+		status = write_reg(ci, 0x0B, 0x33);
+		if (status < 0)
+			break;
+		status = write_reg(ci, 0x0C, 0x33);
+		if (status < 0)
+			break;
+
+		status = write_regm(ci, 0x14, 0x00, 0x0F);
+		if (status < 0)
+			break;
+		status = write_reg(ci, 0x15, ci->clk_reg_b);
+		if (status < 0)
+			break;
+		status = write_regm(ci, 0x16, 0x00, 0x0F);
+		if (status < 0)
+			break;
+		status = write_reg(ci, 0x17, ci->clk_reg_f);
+		if (status < 0)
+			break;
+
+		if (ci->cfg.clock_mode) {
+			if (ci->cfg.polarity) {
+				status = write_reg(ci, 0x09, 0x6f);
+				if (status < 0)
+					break;
+			} else {
+				status = write_reg(ci, 0x09, 0x6d);
+				if (status < 0)
+					break;
+			}
+			status = write_reg(ci, 0x20, 0x68);
+			if (status < 0)
+				break;
+			status = write_reg(ci, 0x21, 0x00);
+			if (status < 0)
+				break;
+			status = write_reg(ci, 0x22, 0x02);
+			if (status < 0)
+				break;
+		} else {
+			if (ci->cfg.polarity) {
+				status = write_reg(ci, 0x09, 0x4f);
+				if (status < 0)
+					break;
+			} else {
+				status = write_reg(ci, 0x09, 0x4d);
+				if (status < 0)
+					break;
+			}
+
+			status = write_reg(ci, 0x20, 0x28);
+			if (status < 0)
+				break;
+			status = write_reg(ci, 0x21, 0x00);
+			if (status < 0)
+				break;
+			status = write_reg(ci, 0x22, 0x07);
+			if (status < 0)
+				break;
+		}
+
+		status = write_regm(ci, 0x20, 0x80, 0x80);
+		if (status < 0)
+			break;
+		status = write_regm(ci, 0x03, 0x02, 0x02);
+		if (status < 0)
+			break;
+		status = write_reg(ci, 0x01, 0x04);
+		if (status < 0)
+			break;
+		status = write_reg(ci, 0x00, 0x31);
+		if (status < 0)
+			break;
+
+		/* Put TS in bypass */
+		status = write_regm(ci, 0x09, 0x08, 0x08);
+		if (status < 0)
+			break;
 		ci->cammode = -1;
-#ifdef BUFFER_MODE
 		cam_mode(ci, 0);
-#endif
 	} while (0);
 	mutex_unlock(&ci->lock);
 
 	return 0;
 }
 
-
 static int read_attribute_mem(struct dvb_ca_en50221 *ca,
 			      int slot, int address)
 {
 	struct cxd *ci = ca->data;
+#if 0
+	if (ci->amem_read) {
+		if (address <= 0 || address > 1024)
+			return -EIO;
+		return ci->amem[address];
+	}
+
+	mutex_lock(&ci->lock);
+	write_regm(ci, 0x06, 0x00, 0x05);
+	read_pccard(ci, 0, &ci->amem[0], 128);
+	read_pccard(ci, 128, &ci->amem[0], 128);
+	read_pccard(ci, 256, &ci->amem[0], 128);
+	read_pccard(ci, 384, &ci->amem[0], 128);
+	write_regm(ci, 0x06, 0x05, 0x05);
+	mutex_unlock(&ci->lock);
+	return ci->amem[address];
+#else
 	u8 val;
 	mutex_lock(&ci->lock);
 	set_mode(ci, 1);
 	read_pccard(ci, address, &val, 1);
 	mutex_unlock(&ci->lock);
+	/* printk(KERN_INFO "%02x:%02x\n", address,val); */
 	return val;
+#endif
 }
 
-
 static int write_attribute_mem(struct dvb_ca_en50221 *ca, int slot,
 			       int address, u8 value)
 {
@@ -372,6 +496,15 @@ static int slot_reset(struct dvb_ca_en50221 *ca, int slot)
 	struct cxd *ci = ca->data;
 
 	mutex_lock(&ci->lock);
+#if 0
+	write_reg(ci, 0x00, 0x21);
+	write_reg(ci, 0x06, 0x1F);
+	write_reg(ci, 0x00, 0x31);
+#else
+#if 0
+	write_reg(ci, 0x06, 0x1F);
+	write_reg(ci, 0x06, 0x2F);
+#else
 	cam_mode(ci, 0);
 	write_reg(ci, 0x00, 0x21);
 	write_reg(ci, 0x06, 0x1F);
@@ -379,13 +512,25 @@ static int slot_reset(struct dvb_ca_en50221 *ca, int slot)
 	write_regm(ci, 0x20, 0x80, 0x80);
 	write_reg(ci, 0x03, 0x02);
 	ci->ready = 0;
+#endif
+#endif
 	ci->mode = -1;
 	{
 		int i;
+#if 0
+		u8 val;
+#endif
 		for (i = 0; i < 100; i++) {
 			msleep(10);
+#if 0
+			read_reg(ci, 0x06, &val);
+			printk(KERN_INFO "%d:%02x\n", i, val);
+			if (!(val&0x10))
+				break;
+#else
 			if (ci->ready)
 				break;
+#endif
 		}
 	}
 	mutex_unlock(&ci->lock);
@@ -399,12 +544,12 @@ static int slot_shutdown(struct dvb_ca_en50221 *ca, int slot)
 
 	printk(KERN_INFO "slot_shutdown\n");
 	mutex_lock(&ci->lock);
-	/* write_regm(ci, 0x09, 0x08, 0x08); */
-	write_regm(ci, 0x20, 0x80, 0x80);
-	write_regm(ci, 0x06, 0x07, 0x07);
+	write_regm(ci, 0x09, 0x08, 0x08);
+	write_regm(ci, 0x20, 0x80, 0x80); /* Reset CAM Mode */
+	write_regm(ci, 0x06, 0x07, 0x07); /* Clear IO Mode */
 	ci->mode = -1;
 	mutex_unlock(&ci->lock);
-	return 0; /* shutdown(ci); */
+	return 0;
 }
 
 static int slot_ts_enable(struct dvb_ca_en50221 *ca, int slot)
@@ -459,7 +604,6 @@ static int campoll(struct cxd *ci)
 		if (istat&8 && ci->slot_stat == DVB_CA_EN50221_POLL_CAM_PRESENT) {
 			ci->ready = 1;
 			ci->slot_stat |= DVB_CA_EN50221_POLL_CAM_READY;
-			printk(KERN_INFO "READY\n");
 		}
 	}
 	return 0;
@@ -510,7 +654,7 @@ static int write_data(struct dvb_ca_en50221 *ca, int slot, u8 *ebuf, int ecount)
 	struct cxd *ci = ca->data;
 
 	mutex_lock(&ci->lock);
-	printk(KERN_INFO "write_data %d\n", ecount);
+	printk(kern_INFO "write_data %d\n", ecount);
 	write_reg(ci, 0x0d, ecount>>8);
 	write_reg(ci, 0x0e, ecount&0xff);
 	write_block(ci, 0x11, ebuf, ecount);
@@ -535,15 +679,15 @@ static struct dvb_ca_en50221 en_templ = {
 
 };
 
-struct dvb_ca_en50221 *cxd2099_attach(u8 adr, void *priv,
+struct dvb_ca_en50221 *cxd2099_attach(struct cxd2099_cfg *cfg,
+				      void *priv,
 				      struct i2c_adapter *i2c)
 {
 	struct cxd *ci = 0;
-	u32 bitrate = 62000000;
 	u8 val;
 
-	if (i2c_read_reg(i2c, adr, 0, &val) < 0) {
-		printk(KERN_ERR "No CXD2099 detected at %02x\n", adr);
+	if (i2c_read_reg(i2c, cfg->adr, 0, &val) < 0) {
+		printk(KERN_INFO "No CXD2099 detected at %02x\n", cfg->adr);
 		return 0;
 	}
 
@@ -553,21 +697,20 @@ struct dvb_ca_en50221 *cxd2099_attach(u8 adr, void *priv,
 	memset(ci, 0, sizeof(*ci));
 
 	mutex_init(&ci->lock);
+	memcpy(&ci->cfg, cfg, sizeof(struct cxd2099_cfg));
 	ci->i2c = i2c;
-	ci->adr = adr;
 	ci->lastaddress = 0xff;
 	ci->clk_reg_b = 0x4a;
 	ci->clk_reg_f = 0x1b;
-	ci->bitrate = bitrate;
 
 	memcpy(&ci->en, &en_templ, sizeof(en_templ));
 	ci->en.data = ci;
 	init(ci);
-	printk(KERN_INFO "Attached CXD2099AR at %02x\n", ci->adr);
+	printk(KERN_INFO "Attached CXD2099AR at %02x\n", ci->cfg.adr);
 	return &ci->en;
 }
 EXPORT_SYMBOL(cxd2099_attach);
 
 MODULE_DESCRIPTION("cxd2099");
-MODULE_AUTHOR("Ralph Metzler <rjkm@metzlerbros.de>");
+MODULE_AUTHOR("Ralph Metzler");
 MODULE_LICENSE("GPL");
diff --git a/drivers/staging/cxd2099/cxd2099.h b/drivers/staging/cxd2099/cxd2099.h
index bed54ff3e30b..19c588a59588 100644
--- a/drivers/staging/cxd2099/cxd2099.h
+++ b/drivers/staging/cxd2099/cxd2099.h
@@ -1,7 +1,7 @@
 /*
  * cxd2099.h: Driver for the CXD2099AR Common Interface Controller
  *
- * Copyright (C) 2010 DigitalDevices UG
+ * Copyright (C) 2010-2011 Digital Devices GmbH
  *
  *
  * This program is free software; you can redistribute it and/or
@@ -27,11 +27,21 @@
 
 #include <dvb_ca_en50221.h>
 
+struct cxd2099_cfg {
+	u32 bitrate;
+	u8  adr;
+	u8  polarity:1;
+	u8  clock_mode:1;
+};
+
 #if defined(CONFIG_DVB_CXD2099) || \
-        (defined(CONFIG_DVB_CXD2099_MODULE) && defined(MODULE))
-struct dvb_ca_en50221 *cxd2099_attach(u8 adr, void *priv, struct i2c_adapter *i2c);
+	(defined(CONFIG_DVB_CXD2099_MODULE) && defined(MODULE))
+struct dvb_ca_en50221 *cxd2099_attach(struct cxd2099_cfg *cfg,
+				      void *priv, struct i2c_adapter *i2c);
 #else
-static inline struct dvb_ca_en50221 *cxd2099_attach(u8 adr, void *priv, struct i2c_adapter *i2c)
+
+static inline struct dvb_ca_en50221 *cxd2099_attach(struct cxd2099_cfg *cfg,
+					void *priv, struct i2c_adapter *i2c)
 {
 	printk(KERN_WARNING "%s: driver disabled by Kconfig\n", __func__);
 	return NULL;
diff --git a/drivers/staging/tm6000/tm6000-alsa.c b/drivers/staging/tm6000/tm6000-alsa.c
index ddfd7c33361b..bd5fa89af07c 100644
--- a/drivers/staging/tm6000/tm6000-alsa.c
+++ b/drivers/staging/tm6000/tm6000-alsa.c
@@ -84,7 +84,6 @@ static int _tm6000_start_audio_dma(struct snd_tm6000_card *chip)
 
 	tm6000_set_audio_bitrate(core, 48000);
 
-
 	return 0;
 }
 
@@ -123,6 +122,7 @@ static int dsp_buffer_alloc(struct snd_pcm_substream *substream, int size)
 	if (substream->runtime->dma_area) {
 		if (substream->runtime->dma_bytes > size)
 			return 0;
+
 		dsp_buffer_free(substream);
 	}
 
@@ -152,9 +152,9 @@ static struct snd_pcm_hardware snd_tm6000_digital_hw = {
 		SNDRV_PCM_INFO_MMAP_VALID,
 	.formats = SNDRV_PCM_FMTBIT_S16_LE,
 
-	.rates =		SNDRV_PCM_RATE_CONTINUOUS,
-	.rate_min =		48000,
-	.rate_max =		48000,
+	.rates = SNDRV_PCM_RATE_CONTINUOUS,
+	.rate_min = 48000,
+	.rate_max = 48000,
 	.channels_min = 2,
 	.channels_max = 2,
 	.period_bytes_min = 64,
@@ -254,9 +254,7 @@ static int tm6000_fillbuf(struct tm6000_core *core, char *buf, int size)
 		memcpy(runtime->dma_area + buf_pos * stride, buf,
 			length * stride);
 
-#ifndef NO_PCM_LOCK
 	snd_pcm_stream_lock(substream);
-#endif
 
 	chip->buf_pos += length;
 	if (chip->buf_pos >= runtime->buffer_size)
@@ -268,9 +266,7 @@ static int tm6000_fillbuf(struct tm6000_core *core, char *buf, int size)
 		period_elapsed = 1;
 	}
 
-#ifndef NO_PCM_LOCK
 	snd_pcm_stream_unlock(substream);
-#endif
 
 	if (period_elapsed)
 		snd_pcm_period_elapsed(substream);