1
2
3
4
5
6
7
8
9
10
11
12
13
14
15
16
17
18
19
20
21
22
23
24
25
26
27
28
29
30
31
32
33
34
35
36
37
38
39
40
41
42
43
44
45
46
47
48
49
50
51
52
53
54
55
56
57
58
59
60
61
62
63
64
65
66
67
68
69
70
71
72
73
74
75
76
77
78
79
80
81
82
83
84
85
86
87
88
89
90
91
|
The device node for Mediatek USB3.0 DRD controller
Required properties:
- compatible : should be "mediatek,<soc-model>-mtu3", "mediatek,mtu3",
soc-model is the name of SoC, such as mt8173, mt2712 etc,
when using "mediatek,mtu3" compatible string, you need SoC specific
ones in addition, one of:
- "mediatek,mt8173-mtu3"
- reg : specifies physical base address and size of the registers
- reg-names: should be "mac" for device IP and "ippc" for IP port control
- interrupts : interrupt used by the device IP
- power-domains : a phandle to USB power domain node to control USB's
mtcmos
- vusb33-supply : regulator of USB avdd3.3v
- clocks : a list of phandle + clock-specifier pairs, one for each
entry in clock-names
- clock-names : must contain "sys_ck" and "ref_ck" for clock of controller;
"wakeup_deb_p0" and "wakeup_deb_p1" are optional, they are
depends on "mediatek,enable-wakeup"
- phys : a list of phandle + phy specifier pairs
- dr_mode : should be one of "host", "peripheral" or "otg",
refer to usb/generic.txt
Optional properties:
- #address-cells, #size-cells : should be '2' if the device has sub-nodes
with 'reg' property
- ranges : allows valid 1:1 translation between child's address space and
parent's address space
- extcon : external connector for vbus and idpin changes detection, needed
when supports dual-role mode.
- vbus-supply : reference to the VBUS regulator, needed when supports
dual-role mode.
- pinctl-names : a pinctrl state named "default" must be defined,
"id_float" and "id_ground" are optinal which depends on
"mediatek,enable-manual-drd"
- pinctrl-0 : pin control group
See: Documentation/devicetree/bindings/pinctrl/pinctrl-bindings.txt
- maximum-speed : valid arguments are "super-speed", "high-speed" and
"full-speed"; refer to usb/generic.txt
- enable-manual-drd : supports manual dual-role switch via debugfs; usually
used when receptacle is TYPE-A and also wants to support dual-role
mode.
- mediatek,enable-wakeup : supports ip sleep wakeup used by host mode
- mediatek,syscon-wakeup : phandle to syscon used to access USB wakeup
control register, it depends on "mediatek,enable-wakeup".
Sub-nodes:
The xhci should be added as subnode to mtu3 as shown in the following example
if host mode is enabled. The DT binding details of xhci can be found in:
Documentation/devicetree/bindings/usb/mediatek,mtk-xhci.txt
Example:
ssusb: usb@11271000 {
compatible = "mediatek,mt8173-mtu3";
reg = <0 0x11271000 0 0x3000>,
<0 0x11280700 0 0x0100>;
reg-names = "mac", "ippc";
interrupts = <GIC_SPI 64 IRQ_TYPE_LEVEL_LOW>;
phys = <&phy_port0 PHY_TYPE_USB3>,
<&phy_port1 PHY_TYPE_USB2>;
power-domains = <&scpsys MT8173_POWER_DOMAIN_USB>;
clocks = <&topckgen CLK_TOP_USB30_SEL>, <&clk26m>,
<&pericfg CLK_PERI_USB0>,
<&pericfg CLK_PERI_USB1>;
clock-names = "sys_ck", "ref_ck",
"wakeup_deb_p0",
"wakeup_deb_p1";
vusb33-supply = <&mt6397_vusb_reg>;
vbus-supply = <&usb_p0_vbus>;
extcon = <&extcon_usb>;
dr_mode = "otg";
mediatek,enable-wakeup;
mediatek,syscon-wakeup = <&pericfg>;
#address-cells = <2>;
#size-cells = <2>;
ranges;
status = "disabled";
usb_host: xhci@11270000 {
compatible = "mediatek,mt8173-xhci";
reg = <0 0x11270000 0 0x1000>;
reg-names = "mac";
interrupts = <GIC_SPI 115 IRQ_TYPE_LEVEL_LOW>;
power-domains = <&scpsys MT8173_POWER_DOMAIN_USB>;
clocks = <&topckgen CLK_TOP_USB30_SEL>, <&clk26m>;
clock-names = "sys_ck", "ref_ck";
vusb33-supply = <&mt6397_vusb_reg>;
status = "disabled";
};
};
|
