3 files changed, 41 insertions, 2 deletions

diff --git a/drivers/mmc/core/core.c b/drivers/mmc/core/core.c
index 68091dda3f31..7843efe22359 100644
--- a/drivers/mmc/core/core.c
+++ b/drivers/mmc/core/core.c
@@ -1245,7 +1245,7 @@ static unsigned int mmc_mmc_erase_timeout(struct mmc_card *card,
 		 */
 		timeout_clks <<= 1;
 		timeout_us += (timeout_clks * 1000) /
-			      (card->host->ios.clock / 1000);
+			      (mmc_host_clk_rate(card->host) / 1000);
 
 		erase_timeout = timeout_us / 1000;
 
diff --git a/drivers/mmc/core/sdio.c b/drivers/mmc/core/sdio.c
index 4d0c15bfa514..262fff019177 100644
--- a/drivers/mmc/core/sdio.c
+++ b/drivers/mmc/core/sdio.c
@@ -691,15 +691,54 @@ static int mmc_sdio_resume(struct mmc_host *host)
 static int mmc_sdio_power_restore(struct mmc_host *host)
 {
 	int ret;
+	u32 ocr;
 
 	BUG_ON(!host);
 	BUG_ON(!host->card);
 
 	mmc_claim_host(host);
+
+	/*
+	 * Reset the card by performing the same steps that are taken by
+	 * mmc_rescan_try_freq() and mmc_attach_sdio() during a "normal" probe.
+	 *
+	 * sdio_reset() is technically not needed. Having just powered up the
+	 * hardware, it should already be in reset state. However, some
+	 * platforms (such as SD8686 on OLPC) do not instantly cut power,
+	 * meaning that a reset is required when restoring power soon after
+	 * powering off. It is harmless in other cases.
+	 *
+	 * The CMD5 reset (mmc_send_io_op_cond()), according to the SDIO spec,
+	 * is not necessary for non-removable cards. However, it is required
+	 * for OLPC SD8686 (which expects a [CMD5,5,3,7] init sequence), and
+	 * harmless in other situations.
+	 *
+	 * With these steps taken, mmc_select_voltage() is also required to
+	 * restore the correct voltage setting of the card.
+	 */
+	sdio_reset(host);
+	mmc_go_idle(host);
+	mmc_send_if_cond(host, host->ocr_avail);
+
+	ret = mmc_send_io_op_cond(host, 0, &ocr);
+	if (ret)
+		goto out;
+
+	if (host->ocr_avail_sdio)
+		host->ocr_avail = host->ocr_avail_sdio;
+
+	host->ocr = mmc_select_voltage(host, ocr & ~0x7F);
+	if (!host->ocr) {
+		ret = -EINVAL;
+		goto out;
+	}
+
 	ret = mmc_sdio_init_card(host, host->ocr, host->card,
 				mmc_card_keep_power(host));
 	if (!ret && host->sdio_irqs)
 		mmc_signal_sdio_irq(host);
+
+out:
 	mmc_release_host(host);
 
 	return ret;
diff --git a/drivers/mmc/core/sdio_bus.c b/drivers/mmc/core/sdio_bus.c
index d29b9c36919a..d2565df8a7fb 100644
--- a/drivers/mmc/core/sdio_bus.c
+++ b/drivers/mmc/core/sdio_bus.c
@@ -189,7 +189,7 @@ static int sdio_bus_remove(struct device *dev)
 
 	/* Then undo the runtime PM settings in sdio_bus_probe() */
 	if (func->card->host->caps & MMC_CAP_POWER_OFF_CARD)
-		pm_runtime_put_noidle(dev);
+		pm_runtime_put_sync(dev);
 
 out:
 	return ret;