diff options
Diffstat (limited to 'drivers/mmc/core/core.c')
| -rw-r--r-- | drivers/mmc/core/core.c | 118 |
1 files changed, 118 insertions, 0 deletions
diff --git a/drivers/mmc/core/core.c b/drivers/mmc/core/core.c index df6ce4a06cf3..fa073ab3fa34 100644 --- a/drivers/mmc/core/core.c +++ b/drivers/mmc/core/core.c @@ -21,6 +21,7 @@ #include <linux/leds.h> #include <linux/scatterlist.h> #include <linux/log2.h> +#include <linux/regulator/consumer.h> #include <linux/mmc/card.h> #include <linux/mmc/host.h> @@ -297,6 +298,21 @@ void mmc_set_data_timeout(struct mmc_data *data, const struct mmc_card *card) data->timeout_clks = 0; } } + /* + * Some cards need very high timeouts if driven in SPI mode. + * The worst observed timeout was 900ms after writing a + * continuous stream of data until the internal logic + * overflowed. + */ + if (mmc_host_is_spi(card->host)) { + if (data->flags & MMC_DATA_WRITE) { + if (data->timeout_ns < 1000000000) + data->timeout_ns = 1000000000; /* 1s */ + } else { + if (data->timeout_ns < 100000000) + data->timeout_ns = 100000000; /* 100ms */ + } + } } EXPORT_SYMBOL(mmc_set_data_timeout); @@ -523,6 +539,105 @@ u32 mmc_vddrange_to_ocrmask(int vdd_min, int vdd_max) } EXPORT_SYMBOL(mmc_vddrange_to_ocrmask); +#ifdef CONFIG_REGULATOR + +/** + * mmc_regulator_get_ocrmask - return mask of supported voltages + * @supply: regulator to use + * + * This returns either a negative errno, or a mask of voltages that + * can be provided to MMC/SD/SDIO devices using the specified voltage + * regulator. This would normally be called before registering the + * MMC host adapter. + */ +int mmc_regulator_get_ocrmask(struct regulator *supply) +{ + int result = 0; + int count; + int i; + + count = regulator_count_voltages(supply); + if (count < 0) + return count; + + for (i = 0; i < count; i++) { + int vdd_uV; + int vdd_mV; + + vdd_uV = regulator_list_voltage(supply, i); + if (vdd_uV <= 0) + continue; + + vdd_mV = vdd_uV / 1000; + result |= mmc_vddrange_to_ocrmask(vdd_mV, vdd_mV); + } + + return result; +} +EXPORT_SYMBOL(mmc_regulator_get_ocrmask); + +/** + * mmc_regulator_set_ocr - set regulator to match host->ios voltage + * @vdd_bit: zero for power off, else a bit number (host->ios.vdd) + * @supply: regulator to use + * + * Returns zero on success, else negative errno. + * + * MMC host drivers may use this to enable or disable a regulator using + * a particular supply voltage. This would normally be called from the + * set_ios() method. + */ +int mmc_regulator_set_ocr(struct regulator *supply, unsigned short vdd_bit) +{ + int result = 0; + int min_uV, max_uV; + int enabled; + + enabled = regulator_is_enabled(supply); + if (enabled < 0) + return enabled; + + if (vdd_bit) { + int tmp; + int voltage; + + /* REVISIT mmc_vddrange_to_ocrmask() may have set some + * bits this regulator doesn't quite support ... don't + * be too picky, most cards and regulators are OK with + * a 0.1V range goof (it's a small error percentage). + */ + tmp = vdd_bit - ilog2(MMC_VDD_165_195); + if (tmp == 0) { + min_uV = 1650 * 1000; + max_uV = 1950 * 1000; + } else { + min_uV = 1900 * 1000 + tmp * 100 * 1000; + max_uV = min_uV + 100 * 1000; + } + + /* avoid needless changes to this voltage; the regulator + * might not allow this operation + */ + voltage = regulator_get_voltage(supply); + if (voltage < 0) + result = voltage; + else if (voltage < min_uV || voltage > max_uV) + result = regulator_set_voltage(supply, min_uV, max_uV); + else + result = 0; + + if (result == 0 && !enabled) + result = regulator_enable(supply); + } else if (enabled) { + result = regulator_disable(supply); + } + + return result; +} +EXPORT_SYMBOL(mmc_regulator_set_ocr); + +#endif + /* * Mask off any voltages we don't support and select * the lowest voltage @@ -815,6 +930,7 @@ void mmc_stop_host(struct mmc_host *host) spin_unlock_irqrestore(&host->lock, flags); #endif + cancel_delayed_work(&host->detect); mmc_flush_scheduled_work(); mmc_bus_get(host); @@ -842,6 +958,7 @@ void mmc_stop_host(struct mmc_host *host) */ int mmc_suspend_host(struct mmc_host *host, pm_message_t state) { + cancel_delayed_work(&host->detect); mmc_flush_scheduled_work(); mmc_bus_get(host); @@ -875,6 +992,7 @@ int mmc_resume_host(struct mmc_host *host) mmc_bus_get(host); if (host->bus_ops && !host->bus_dead) { mmc_power_up(host); + mmc_select_voltage(host, host->ocr); BUG_ON(!host->bus_ops->resume); host->bus_ops->resume(host); } |