diff options
Diffstat (limited to 'arch/arm')
77 files changed, 1972 insertions, 1183 deletions
diff --git a/arch/arm/Kconfig b/arch/arm/Kconfig index 7a74e3e5f916..50b9afa8ae6d 100644 --- a/arch/arm/Kconfig +++ b/arch/arm/Kconfig @@ -99,13 +99,6 @@ config ARCH_EBSA110 Ethernet interface, two PCMCIA sockets, two serial ports and a parallel port. -config ARCH_CAMELOT - bool "Epxa10db" - help - This enables support for Altera's Excalibur XA10 development board. - If you would like to build your kernel to run on one of these boards - then you must say 'Y' here. Otherwise say 'N' - config ARCH_FOOTBRIDGE bool "FootBridge" select FOOTBRIDGE @@ -213,12 +206,16 @@ config ARCH_AAEC2000 help This enables support for systems based on the Agilent AAEC-2000 +config ARCH_AT91RM9200 + bool "AT91RM9200" + help + Say Y here if you intend to run this kernel on an AT91RM9200-based + board. + endchoice source "arch/arm/mach-clps711x/Kconfig" -source "arch/arm/mach-epxa10db/Kconfig" - source "arch/arm/mach-footbridge/Kconfig" source "arch/arm/mach-integrator/Kconfig" @@ -253,6 +250,8 @@ source "arch/arm/mach-aaec2000/Kconfig" source "arch/arm/mach-realview/Kconfig" +source "arch/arm/mach-at91rm9200/Kconfig" + # Definitions to make life easier config ARCH_ACORN bool @@ -418,7 +417,8 @@ config LEDS ARCH_EBSA285 || ARCH_IMX || ARCH_INTEGRATOR || \ ARCH_LUBBOCK || MACH_MAINSTONE || ARCH_NETWINDER || \ ARCH_OMAP || ARCH_P720T || ARCH_PXA_IDP || \ - ARCH_SA1100 || ARCH_SHARK || ARCH_VERSATILE + ARCH_SA1100 || ARCH_SHARK || ARCH_VERSATILE || \ + ARCH_AT91RM9200 help If you say Y here, the LEDs on your machine will be used to provide useful information about your current system status. diff --git a/arch/arm/Makefile b/arch/arm/Makefile index afaf3a1e903c..1fa2a1011584 100644 --- a/arch/arm/Makefile +++ b/arch/arm/Makefile @@ -84,7 +84,6 @@ endif machine-$(CONFIG_ARCH_PXA) := pxa machine-$(CONFIG_ARCH_L7200) := l7200 machine-$(CONFIG_ARCH_INTEGRATOR) := integrator - machine-$(CONFIG_ARCH_CAMELOT) := epxa10db textofs-$(CONFIG_ARCH_CLPS711X) := 0x00028000 machine-$(CONFIG_ARCH_CLPS711X) := clps711x machine-$(CONFIG_ARCH_IOP3XX) := iop3xx @@ -100,6 +99,7 @@ endif machine-$(CONFIG_ARCH_H720X) := h720x machine-$(CONFIG_ARCH_AAEC2000) := aaec2000 machine-$(CONFIG_ARCH_REALVIEW) := realview + machine-$(CONFIG_ARCH_AT91RM9200) := at91rm9200 ifeq ($(CONFIG_ARCH_EBSA110),y) # This is what happens if you forget the IOCS16 line. diff --git a/arch/arm/boot/compressed/Makefile b/arch/arm/boot/compressed/Makefile index 6b505ce41a75..35ffe0f4ece7 100644 --- a/arch/arm/boot/compressed/Makefile +++ b/arch/arm/boot/compressed/Makefile @@ -21,10 +21,6 @@ ifeq ($(CONFIG_ARCH_SHARK),y) OBJS += head-shark.o ofw-shark.o endif -ifeq ($(CONFIG_ARCH_CAMELOT),y) -OBJS += head-epxa10db.o -endif - ifeq ($(CONFIG_ARCH_L7200),y) OBJS += head-l7200.o endif @@ -50,6 +46,10 @@ ifeq ($(CONFIG_PXA_SHARPSL),y) OBJS += head-sharpsl.o endif +ifeq ($(CONFIG_ARCH_AT91RM9200),y) +OBJS += head-at91rm9200.o +endif + ifeq ($(CONFIG_DEBUG_ICEDCC),y) OBJS += ice-dcc.o endif diff --git a/arch/arm/boot/compressed/head-at91rm9200.S b/arch/arm/boot/compressed/head-at91rm9200.S new file mode 100644 index 000000000000..2119ea62b547 --- /dev/null +++ b/arch/arm/boot/compressed/head-at91rm9200.S @@ -0,0 +1,57 @@ +/* + * linux/arch/arm/boot/compressed/head-at91rm9200.S + * + * Copyright (C) 2003 SAN People + * + * This program is free software; you can redistribute it and/or modify + * it under the terms of the GNU General Public License as published by + * the Free Software Foundation; either version 2 of the License, or + * (at your option) any later version. + * + */ +#include <asm/mach-types.h> + + .section ".start", "ax" + + @ Atmel AT91RM9200-DK : 262 + mov r3, #(MACH_TYPE_AT91RM9200DK & 0xff) + orr r3, r3, #(MACH_TYPE_AT91RM9200DK & 0xff00) + cmp r7, r3 + beq 99f + + @ Cogent CSB337 : 399 + mov r3, #(MACH_TYPE_CSB337 & 0xff) + orr r3, r3, #(MACH_TYPE_CSB337 & 0xff00) + cmp r7, r3 + beq 99f + + @ Cogent CSB637 : 648 + mov r3, #(MACH_TYPE_CSB637 & 0xff) + orr r3, r3, #(MACH_TYPE_CSB637 & 0xff00) + cmp r7, r3 + beq 99f + + @ Atmel AT91RM9200-EK : 705 + mov r3, #(MACH_TYPE_AT91RM9200EK & 0xff) + orr r3, r3, #(MACH_TYPE_AT91RM9200EK & 0xff00) + cmp r7, r3 + beq 99f + + @ Conitec Carmeva : 769 + mov r3, #(MACH_TYPE_CARMEVA & 0xff) + orr r3, r3, #(MACH_TYPE_CARMEVA & 0xff00) + cmp r7, r3 + beq 99f + + @ KwikByte KB920x : 612 + mov r3, #(MACH_TYPE_KB9200 & 0xff) + orr r3, r3, #(MACH_TYPE_KB9200 & 0xff00) + cmp r7, r3 + beq 99f + + @ Unknown board, use the AT91RM9200DK board + @ mov r7, #MACH_TYPE_AT91RM9200 + mov r7, #(MACH_TYPE_AT91RM9200DK & 0xff) + orr r7, r7, #(MACH_TYPE_AT91RM9200DK & 0xff00) + +99: diff --git a/arch/arm/boot/compressed/head-epxa10db.S b/arch/arm/boot/compressed/head-epxa10db.S deleted file mode 100644 index 757681f12a39..000000000000 --- a/arch/arm/boot/compressed/head-epxa10db.S +++ /dev/null @@ -1,5 +0,0 @@ -#include <asm/mach-types.h> -#include <asm/arch/excalibur.h> - - .section ".start", "ax" - mov r7, #MACH_TYPE_CAMELOT diff --git a/arch/arm/configs/assabet_defconfig b/arch/arm/configs/assabet_defconfig index ccbb4c0d58c4..089c9d598409 100644 --- a/arch/arm/configs/assabet_defconfig +++ b/arch/arm/configs/assabet_defconfig @@ -63,7 +63,6 @@ CONFIG_OBSOLETE_MODPARM=y # CONFIG_ARCH_CLPS711X is not set # CONFIG_ARCH_CO285 is not set # CONFIG_ARCH_EBSA110 is not set -# CONFIG_ARCH_CAMELOT is not set # CONFIG_ARCH_FOOTBRIDGE is not set # CONFIG_ARCH_INTEGRATOR is not set # CONFIG_ARCH_IOP3XX is not set diff --git a/arch/arm/configs/badge4_defconfig b/arch/arm/configs/badge4_defconfig index 5d92af975d87..cfe6bd8e81cd 100644 --- a/arch/arm/configs/badge4_defconfig +++ b/arch/arm/configs/badge4_defconfig @@ -66,7 +66,6 @@ CONFIG_KMOD=y # CONFIG_ARCH_CLPS711X is not set # CONFIG_ARCH_CO285 is not set # CONFIG_ARCH_EBSA110 is not set -# CONFIG_ARCH_CAMELOT is not set # CONFIG_ARCH_FOOTBRIDGE is not set # CONFIG_ARCH_INTEGRATOR is not set # CONFIG_ARCH_IOP3XX is not set diff --git a/arch/arm/configs/bast_defconfig b/arch/arm/configs/bast_defconfig index 35e3a99bcbb6..6886001b5366 100644 --- a/arch/arm/configs/bast_defconfig +++ b/arch/arm/configs/bast_defconfig @@ -64,7 +64,6 @@ CONFIG_KMOD=y # CONFIG_ARCH_CLPS711X is not set # CONFIG_ARCH_CO285 is not set # CONFIG_ARCH_EBSA110 is not set -# CONFIG_ARCH_CAMELOT is not set # CONFIG_ARCH_FOOTBRIDGE is not set # CONFIG_ARCH_INTEGRATOR is not set # CONFIG_ARCH_IOP3XX is not set diff --git a/arch/arm/configs/cerfcube_defconfig b/arch/arm/configs/cerfcube_defconfig index d8fe0f40408f..f81a60005cd3 100644 --- a/arch/arm/configs/cerfcube_defconfig +++ b/arch/arm/configs/cerfcube_defconfig @@ -65,7 +65,6 @@ CONFIG_KMOD=y # CONFIG_ARCH_CLPS711X is not set # CONFIG_ARCH_CO285 is not set # CONFIG_ARCH_EBSA110 is not set -# CONFIG_ARCH_CAMELOT is not set # CONFIG_ARCH_FOOTBRIDGE is not set # CONFIG_ARCH_INTEGRATOR is not set # CONFIG_ARCH_IOP3XX is not set diff --git a/arch/arm/configs/clps7500_defconfig b/arch/arm/configs/clps7500_defconfig index 908758371405..af9ae5389131 100644 --- a/arch/arm/configs/clps7500_defconfig +++ b/arch/arm/configs/clps7500_defconfig @@ -57,7 +57,6 @@ CONFIG_ARCH_CLPS7500=y # CONFIG_ARCH_CLPS711X is not set # CONFIG_ARCH_CO285 is not set # CONFIG_ARCH_EBSA110 is not set -# CONFIG_ARCH_CAMELOT is not set # CONFIG_ARCH_FOOTBRIDGE is not set # CONFIG_ARCH_INTEGRATOR is not set # CONFIG_ARCH_IOP3XX is not set diff --git a/arch/arm/configs/collie_defconfig b/arch/arm/configs/collie_defconfig index 40dfe07a8bce..15468a0cf70e 100644 --- a/arch/arm/configs/collie_defconfig +++ b/arch/arm/configs/collie_defconfig @@ -71,7 +71,6 @@ CONFIG_KMOD=y # CONFIG_ARCH_CLPS711X is not set # CONFIG_ARCH_CO285 is not set # CONFIG_ARCH_EBSA110 is not set -# CONFIG_ARCH_CAMELOT is not set # CONFIG_ARCH_FOOTBRIDGE is not set # CONFIG_ARCH_INTEGRATOR is not set # CONFIG_ARCH_IOP3XX is not set diff --git a/arch/arm/configs/corgi_defconfig b/arch/arm/configs/corgi_defconfig index 06229026f78b..3c3461e83398 100644 --- a/arch/arm/configs/corgi_defconfig +++ b/arch/arm/configs/corgi_defconfig @@ -87,7 +87,6 @@ CONFIG_DEFAULT_IOSCHED="anticipatory" # CONFIG_ARCH_CLPS711X is not set # CONFIG_ARCH_CO285 is not set # CONFIG_ARCH_EBSA110 is not set -# CONFIG_ARCH_CAMELOT is not set # CONFIG_ARCH_FOOTBRIDGE is not set # CONFIG_ARCH_INTEGRATOR is not set # CONFIG_ARCH_IOP3XX is not set diff --git a/arch/arm/configs/ebsa110_defconfig b/arch/arm/configs/ebsa110_defconfig index 6f61929b97a8..afcfff6140f2 100644 --- a/arch/arm/configs/ebsa110_defconfig +++ b/arch/arm/configs/ebsa110_defconfig @@ -63,7 +63,6 @@ CONFIG_KMOD=y # CONFIG_ARCH_CLPS711X is not set # CONFIG_ARCH_CO285 is not set CONFIG_ARCH_EBSA110=y -# CONFIG_ARCH_CAMELOT is not set # CONFIG_ARCH_FOOTBRIDGE is not set # CONFIG_ARCH_INTEGRATOR is not set # CONFIG_ARCH_IOP3XX is not set diff --git a/arch/arm/configs/edb7211_defconfig b/arch/arm/configs/edb7211_defconfig index 78b08ed4d5f4..6ba7355ff85b 100644 --- a/arch/arm/configs/edb7211_defconfig +++ b/arch/arm/configs/edb7211_defconfig @@ -57,7 +57,6 @@ CONFIG_BASE_SMALL=0 CONFIG_ARCH_CLPS711X=y # CONFIG_ARCH_CO285 is not set # CONFIG_ARCH_EBSA110 is not set -# CONFIG_ARCH_CAMELOT is not set # CONFIG_ARCH_FOOTBRIDGE is not set # CONFIG_ARCH_INTEGRATOR is not set # CONFIG_ARCH_IOP3XX is not set diff --git a/arch/arm/configs/enp2611_defconfig b/arch/arm/configs/enp2611_defconfig index fd7c0042bcca..9592e3925c79 100644 --- a/arch/arm/configs/enp2611_defconfig +++ b/arch/arm/configs/enp2611_defconfig @@ -86,7 +86,6 @@ CONFIG_DEFAULT_IOSCHED="anticipatory" # CONFIG_ARCH_CLPS711X is not set # CONFIG_ARCH_CO285 is not set # CONFIG_ARCH_EBSA110 is not set -# CONFIG_ARCH_CAMELOT is not set # CONFIG_ARCH_FOOTBRIDGE is not set # CONFIG_ARCH_INTEGRATOR is not set # CONFIG_ARCH_IOP3XX is not set diff --git a/arch/arm/configs/ep80219_defconfig b/arch/arm/configs/ep80219_defconfig index 96342afa9c5f..fbe312e757cb 100644 --- a/arch/arm/configs/ep80219_defconfig +++ b/arch/arm/configs/ep80219_defconfig @@ -64,7 +64,6 @@ CONFIG_KMOD=y # CONFIG_ARCH_CLPS711X is not set # CONFIG_ARCH_CO285 is not set # CONFIG_ARCH_EBSA110 is not set -# CONFIG_ARCH_CAMELOT is not set # CONFIG_ARCH_FOOTBRIDGE is not set # CONFIG_ARCH_INTEGRATOR is not set CONFIG_ARCH_IOP3XX=y diff --git a/arch/arm/configs/epxa10db_defconfig b/arch/arm/configs/epxa10db_defconfig deleted file mode 100644 index 9fb8b58c4954..000000000000 --- a/arch/arm/configs/epxa10db_defconfig +++ /dev/null @@ -1,644 +0,0 @@ -# -# Automatically generated make config: don't edit -# Linux kernel version: 2.6.12-rc1-bk2 -# Sun Mar 27 22:46:51 2005 -# -CONFIG_ARM=y -CONFIG_MMU=y -CONFIG_UID16=y -CONFIG_RWSEM_GENERIC_SPINLOCK=y -CONFIG_GENERIC_CALIBRATE_DELAY=y -CONFIG_GENERIC_IOMAP=y - -# -# Code maturity level options -# -CONFIG_EXPERIMENTAL=y -CONFIG_CLEAN_COMPILE=y -CONFIG_BROKEN_ON_SMP=y - -# -# General setup -# -CONFIG_LOCALVERSION="" -CONFIG_SWAP=y -CONFIG_SYSVIPC=y -# CONFIG_POSIX_MQUEUE is not set -# CONFIG_BSD_PROCESS_ACCT is not set -CONFIG_SYSCTL=y -# CONFIG_AUDIT is not set -# CONFIG_HOTPLUG is not set -CONFIG_KOBJECT_UEVENT=y -# CONFIG_IKCONFIG is not set -# CONFIG_EMBEDDED is not set -CONFIG_KALLSYMS=y -# CONFIG_KALLSYMS_EXTRA_PASS is not set -CONFIG_BASE_FULL=y -CONFIG_FUTEX=y -CONFIG_EPOLL=y -CONFIG_CC_OPTIMIZE_FOR_SIZE=y -CONFIG_SHMEM=y -CONFIG_CC_ALIGN_FUNCTIONS=0 -CONFIG_CC_ALIGN_LABELS=0 -CONFIG_CC_ALIGN_LOOPS=0 -CONFIG_CC_ALIGN_JUMPS=0 -# CONFIG_TINY_SHMEM is not set -CONFIG_BASE_SMALL=0 - -# -# Loadable module support -# -CONFIG_MODULES=y -CONFIG_MODULE_UNLOAD=y -# CONFIG_MODULE_FORCE_UNLOAD is not set -CONFIG_OBSOLETE_MODPARM=y -# CONFIG_MODVERSIONS is not set -# CONFIG_MODULE_SRCVERSION_ALL is not set -# CONFIG_KMOD is not set - -# -# System Type -# -# CONFIG_ARCH_CLPS7500 is not set -# CONFIG_ARCH_CLPS711X is not set -# CONFIG_ARCH_CO285 is not set -# CONFIG_ARCH_EBSA110 is not set -CONFIG_ARCH_CAMELOT=y -# CONFIG_ARCH_FOOTBRIDGE is not set -# CONFIG_ARCH_INTEGRATOR is not set -# CONFIG_ARCH_IOP3XX is not set -# CONFIG_ARCH_IXP4XX is not set -# CONFIG_ARCH_IXP2000 is not set -# CONFIG_ARCH_L7200 is not set -# CONFIG_ARCH_PXA is not set -# CONFIG_ARCH_RPC is not set -# CONFIG_ARCH_SA1100 is not set -# CONFIG_ARCH_S3C2410 is not set -# CONFIG_ARCH_SHARK is not set -# CONFIG_ARCH_LH7A40X is not set -# CONFIG_ARCH_OMAP is not set -# CONFIG_ARCH_VERSATILE is not set -# CONFIG_ARCH_IMX is not set -# CONFIG_ARCH_H720X is not set - -# -# Epxa10db -# - -# -# PLD hotswap support -# -CONFIG_PLD=y -# CONFIG_PLD_HOTSWAP is not set - -# -# Processor Type -# -CONFIG_CPU_32=y -CONFIG_CPU_ARM922T=y -CONFIG_CPU_32v4=y -CONFIG_CPU_ABRT_EV4T=y -CONFIG_CPU_CACHE_V4WT=y -CONFIG_CPU_CACHE_VIVT=y -CONFIG_CPU_COPY_V4WB=y -CONFIG_CPU_TLB_V4WBI=y - -# -# Processor Features -# -# CONFIG_ARM_THUMB is not set -# CONFIG_CPU_ICACHE_DISABLE is not set -# CONFIG_CPU_DCACHE_DISABLE is not set -# CONFIG_CPU_DCACHE_WRITETHROUGH is not set - -# -# Bus support -# - -# -# PCCARD (PCMCIA/CardBus) support -# -# CONFIG_PCCARD is not set - -# -# Kernel Features -# -# CONFIG_PREEMPT is not set -CONFIG_ALIGNMENT_TRAP=y - -# -# Boot options -# -CONFIG_ZBOOT_ROM_TEXT=0x0 -CONFIG_ZBOOT_ROM_BSS=0x0 -CONFIG_CMDLINE="mem=32M console=ttyUA0,115200 initrd=0x00200000,8M root=/dev/ram0 rw" -# CONFIG_XIP_KERNEL is not set - -# -# Floating point emulation -# - -# -# At least one emulation must be selected -# -CONFIG_FPE_NWFPE=y -# CONFIG_FPE_NWFPE_XP is not set -# CONFIG_FPE_FASTFPE is not set - -# -# Userspace binary formats -# -CONFIG_BINFMT_ELF=y -# CONFIG_BINFMT_AOUT is not set -# CONFIG_BINFMT_MISC is not set -# CONFIG_ARTHUR is not set - -# -# Power management options -# -# CONFIG_PM is not set - -# -# Device Drivers -# - -# -# Generic Driver Options -# -CONFIG_STANDALONE=y -CONFIG_PREVENT_FIRMWARE_BUILD=y -# CONFIG_FW_LOADER is not set - -# -# Memory Technology Devices (MTD) -# -# CONFIG_MTD is not set - -# -# Parallel port support -# -# CONFIG_PARPORT is not set - -# -# Plug and Play support -# - -# -# Block devices -# -# CONFIG_BLK_DEV_FD is not set -# CONFIG_BLK_DEV_COW_COMMON is not set -CONFIG_BLK_DEV_LOOP=y -# CONFIG_BLK_DEV_CRYPTOLOOP is not set -# CONFIG_BLK_DEV_NBD is not set -CONFIG_BLK_DEV_RAM=y -CONFIG_BLK_DEV_RAM_COUNT=16 -CONFIG_BLK_DEV_RAM_SIZE=8192 -CONFIG_BLK_DEV_INITRD=y -CONFIG_INITRAMFS_SOURCE="" -# CONFIG_CDROM_PKTCDVD is not set - -# -# IO Schedulers -# -CONFIG_IOSCHED_NOOP=y -CONFIG_IOSCHED_AS=y -CONFIG_IOSCHED_DEADLINE=y -CONFIG_IOSCHED_CFQ=y -# CONFIG_ATA_OVER_ETH is not set - -# -# SCSI device support -# -# CONFIG_SCSI is not set - -# -# Multi-device support (RAID and LVM) -# -# CONFIG_MD is not set - -# -# Fusion MPT device support -# - -# -# IEEE 1394 (FireWire) support -# - -# -# I2O device support -# - -# -# Networking support -# -CONFIG_NET=y - -# -# Networking options -# -CONFIG_PACKET=y -# CONFIG_PACKET_MMAP is not set -# CONFIG_NETLINK_DEV is not set -CONFIG_UNIX=y -# CONFIG_NET_KEY is not set -CONFIG_INET=y -CONFIG_IP_MULTICAST=y -# CONFIG_IP_ADVANCED_ROUTER is not set -CONFIG_IP_PNP=y -# CONFIG_IP_PNP_DHCP is not set -# CONFIG_IP_PNP_BOOTP is not set -# CONFIG_IP_PNP_RARP is not set -# CONFIG_NET_IPIP is not set -# CONFIG_NET_IPGRE is not set -# CONFIG_IP_MROUTE is not set -# CONFIG_ARPD is not set -# CONFIG_SYN_COOKIES is not set -# CONFIG_INET_AH is not set -# CONFIG_INET_ESP is not set -# CONFIG_INET_IPCOMP is not set -# CONFIG_INET_TUNNEL is not set -# CONFIG_IP_TCPDIAG is not set -# CONFIG_IP_TCPDIAG_IPV6 is not set -# CONFIG_IPV6 is not set -# CONFIG_NETFILTER is not set - -# -# SCTP Configuration (EXPERIMENTAL) -# -# CONFIG_IP_SCTP is not set -# CONFIG_ATM is not set -# CONFIG_BRIDGE is not set -# CONFIG_VLAN_8021Q is not set -# CONFIG_DECNET is not set -# CONFIG_LLC2 is not set -# CONFIG_IPX is not set -# CONFIG_ATALK is not set -# CONFIG_X25 is not set -# CONFIG_LAPB is not set -# CONFIG_NET_DIVERT is not set -# CONFIG_ECONET is not set -# CONFIG_WAN_ROUTER is not set - -# -# QoS and/or fair queueing -# -# CONFIG_NET_SCHED is not set -# CONFIG_NET_CLS_ROUTE is not set - -# -# Network testing -# -# CONFIG_NET_PKTGEN is not set -# CONFIG_NETPOLL is not set -# CONFIG_NET_POLL_CONTROLLER is not set -# CONFIG_HAMRADIO is not set -# CONFIG_IRDA is not set -# CONFIG_BT is not set -CONFIG_NETDEVICES=y -# CONFIG_DUMMY is not set -# CONFIG_BONDING is not set -# CONFIG_EQUALIZER is not set -# CONFIG_TUN is not set - -# -# Ethernet (10 or 100Mbit) -# -# CONFIG_NET_ETHERNET is not set - -# -# Ethernet (1000 Mbit) -# - -# -# Ethernet (10000 Mbit) -# - -# -# Token Ring devices -# - -# -# Wireless LAN (non-hamradio) -# -# CONFIG_NET_RADIO is not set - -# -# Wan interfaces -# -# CONFIG_WAN is not set -CONFIG_PPP=y -CONFIG_PPP_MULTILINK=y -# CONFIG_PPP_FILTER is not set -CONFIG_PPP_ASYNC=y -CONFIG_PPP_SYNC_TTY=y -CONFIG_PPP_DEFLATE=y -# CONFIG_PPP_BSDCOMP is not set -# CONFIG_PPPOE is not set -# CONFIG_SLIP is not set -# CONFIG_SHAPER is not set -# CONFIG_NETCONSOLE is not set - -# -# ISDN subsystem -# -# CONFIG_ISDN is not set - -# -# Input device support -# -CONFIG_INPUT=y - -# -# Userland interfaces -# -CONFIG_INPUT_MOUSEDEV=y -CONFIG_INPUT_MOUSEDEV_PSAUX=y -CONFIG_INPUT_MOUSEDEV_SCREEN_X=1024 -CONFIG_INPUT_MOUSEDEV_SCREEN_Y=768 -# CONFIG_INPUT_JOYDEV is not set -# CONFIG_INPUT_TSDEV is not set -# CONFIG_INPUT_EVDEV is not set -# CONFIG_INPUT_EVBUG is not set - -# -# Input Device Drivers -# -# CONFIG_INPUT_KEYBOARD is not set -# CONFIG_INPUT_MOUSE is not set -# CONFIG_INPUT_JOYSTICK is not set -# CONFIG_INPUT_TOUCHSCREEN is not set -# CONFIG_INPUT_MISC is not set - -# -# Hardware I/O ports -# -CONFIG_SERIO=y -CONFIG_SERIO_SERPORT=y -# CONFIG_SERIO_RAW is not set -# CONFIG_GAMEPORT is not set -CONFIG_SOUND_GAMEPORT=y - -# -# Character devices -# -CONFIG_VT=y -CONFIG_VT_CONSOLE=y -CONFIG_HW_CONSOLE=y -# CONFIG_SERIAL_NONSTANDARD is not set - -# -# Serial drivers -# -# CONFIG_SERIAL_8250 is not set - -# -# Non-8250 serial port support -# -CONFIG_SERIAL_UART00=y -CONFIG_SERIAL_UART00_CONSOLE=y -CONFIG_SERIAL_CORE=y -CONFIG_SERIAL_CORE_CONSOLE=y -CONFIG_UNIX98_PTYS=y -CONFIG_LEGACY_PTYS=y -CONFIG_LEGACY_PTY_COUNT=256 - -# -# IPMI -# -# CONFIG_IPMI_HANDLER is not set - -# -# Watchdog Cards -# -# CONFIG_WATCHDOG is not set -# CONFIG_NVRAM is not set -# CONFIG_RTC is not set -# CONFIG_DTLK is not set -# CONFIG_R3964 is not set - -# -# Ftape, the floppy tape device driver -# -# CONFIG_DRM is not set -# CONFIG_RAW_DRIVER is not set - -# -# TPM devices -# -# CONFIG_TCG_TPM is not set - -# -# I2C support -# -# CONFIG_I2C is not set - -# -# Misc devices -# - -# -# Multimedia devices -# -# CONFIG_VIDEO_DEV is not set - -# -# Digital Video Broadcasting Devices -# -# CONFIG_DVB is not set - -# -# Graphics support -# -# CONFIG_FB is not set - -# -# Console display driver support -# -# CONFIG_VGA_CONSOLE is not set -CONFIG_DUMMY_CONSOLE=y - -# -# Sound -# -# CONFIG_SOUND is not set - -# -# USB support -# -CONFIG_USB_ARCH_HAS_HCD=y -# CONFIG_USB_ARCH_HAS_OHCI is not set -# CONFIG_USB is not set - -# -# USB Gadget Support -# -# CONFIG_USB_GADGET is not set - -# -# MMC/SD Card support -# -# CONFIG_MMC is not set - -# -# File systems -# -CONFIG_EXT2_FS=y -# CONFIG_EXT2_FS_XATTR is not set -# CONFIG_EXT3_FS is not set -# CONFIG_JBD is not set -# CONFIG_REISERFS_FS is not set -# CONFIG_JFS_FS is not set - -# -# XFS support -# -# CONFIG_XFS_FS is not set -# CONFIG_MINIX_FS is not set -# CONFIG_ROMFS_FS is not set -# CONFIG_QUOTA is not set -CONFIG_DNOTIFY=y -CONFIG_AUTOFS_FS=y -CONFIG_AUTOFS4_FS=y - -# -# CD-ROM/DVD Filesystems -# -# CONFIG_ISO9660_FS is not set -# CONFIG_UDF_FS is not set - -# -# DOS/FAT/NT Filesystems -# -# CONFIG_MSDOS_FS is not set -# CONFIG_VFAT_FS is not set -# CONFIG_NTFS_FS is not set - -# -# Pseudo filesystems -# -CONFIG_PROC_FS=y -CONFIG_SYSFS=y -# CONFIG_DEVFS_FS is not set -# CONFIG_DEVPTS_FS_XATTR is not set -# CONFIG_TMPFS is not set -# CONFIG_HUGETLB_PAGE is not set -CONFIG_RAMFS=y - -# -# Miscellaneous filesystems -# -# CONFIG_ADFS_FS is not set -# CONFIG_AFFS_FS is not set -# CONFIG_HFS_FS is not set -# CONFIG_HFSPLUS_FS is not set -# CONFIG_BEFS_FS is not set -# CONFIG_BFS_FS is not set -# CONFIG_EFS_FS is not set -# CONFIG_CRAMFS is not set -# CONFIG_VXFS_FS is not set -# CONFIG_HPFS_FS is not set -# CONFIG_QNX4FS_FS is not set -# CONFIG_SYSV_FS is not set -# CONFIG_UFS_FS is not set - -# -# Network File Systems -# -# CONFIG_NFS_FS is not set -# CONFIG_NFSD is not set -CONFIG_SMB_FS=y -# CONFIG_SMB_NLS_DEFAULT is not set -# CONFIG_CIFS is not set -# CONFIG_NCP_FS is not set -# CONFIG_CODA_FS is not set -# CONFIG_AFS_FS is not set - -# -# Partition Types -# -# CONFIG_PARTITION_ADVANCED is not set -CONFIG_MSDOS_PARTITION=y - -# -# Native Language Support -# -CONFIG_NLS=y -CONFIG_NLS_DEFAULT="iso8859-1" -# CONFIG_NLS_CODEPAGE_437 is not set -# CONFIG_NLS_CODEPAGE_737 is not set -# CONFIG_NLS_CODEPAGE_775 is not set -# CONFIG_NLS_CODEPAGE_850 is not set -# CONFIG_NLS_CODEPAGE_852 is not set -# CONFIG_NLS_CODEPAGE_855 is not set -# CONFIG_NLS_CODEPAGE_857 is not set -# CONFIG_NLS_CODEPAGE_860 is not set -# CONFIG_NLS_CODEPAGE_861 is not set -# CONFIG_NLS_CODEPAGE_862 is not set -# CONFIG_NLS_CODEPAGE_863 is not set -# CONFIG_NLS_CODEPAGE_864 is not set -# CONFIG_NLS_CODEPAGE_865 is not set -# CONFIG_NLS_CODEPAGE_866 is not set -# CONFIG_NLS_CODEPAGE_869 is not set -# CONFIG_NLS_CODEPAGE_936 is not set -# CONFIG_NLS_CODEPAGE_950 is not set -# CONFIG_NLS_CODEPAGE_932 is not set -# CONFIG_NLS_CODEPAGE_949 is not set -# CONFIG_NLS_CODEPAGE_874 is not set -# CONFIG_NLS_ISO8859_8 is not set -# CONFIG_NLS_CODEPAGE_1250 is not set -# CONFIG_NLS_CODEPAGE_1251 is not set -# CONFIG_NLS_ASCII is not set -# CONFIG_NLS_ISO8859_1 is not set -# CONFIG_NLS_ISO8859_2 is not set -# CONFIG_NLS_ISO8859_3 is not set -# CONFIG_NLS_ISO8859_4 is not set -# CONFIG_NLS_ISO8859_5 is not set -# CONFIG_NLS_ISO8859_6 is not set -# CONFIG_NLS_ISO8859_7 is not set -# CONFIG_NLS_ISO8859_9 is not set -# CONFIG_NLS_ISO8859_13 is not set -# CONFIG_NLS_ISO8859_14 is not set -# CONFIG_NLS_ISO8859_15 is not set -# CONFIG_NLS_KOI8_R is not set -# CONFIG_NLS_KOI8_U is not set -# CONFIG_NLS_UTF8 is not set - -# -# Profiling support -# -# CONFIG_PROFILING is not set - -# -# Kernel hacking -# -# CONFIG_PRINTK_TIME is not set -# CONFIG_DEBUG_KERNEL is not set -CONFIG_LOG_BUF_SHIFT=14 -CONFIG_DEBUG_BUGVERBOSE=y -CONFIG_FRAME_POINTER=y -# CONFIG_DEBUG_USER is not set - -# -# Security options -# -# CONFIG_KEYS is not set -# CONFIG_SECURITY is not set - -# -# Cryptographic options -# -# CONFIG_CRYPTO is not set - -# -# Hardware crypto devices -# - -# -# Library routines -# -CONFIG_CRC_CCITT=y -CONFIG_CRC32=y -# CONFIG_LIBCRC32C is not set -CONFIG_ZLIB_INFLATE=y -CONFIG_ZLIB_DEFLATE=y diff --git a/arch/arm/configs/footbridge_defconfig b/arch/arm/configs/footbridge_defconfig index 9737c4850721..2a612d23120b 100644 --- a/arch/arm/configs/footbridge_defconfig +++ b/arch/arm/configs/footbridge_defconfig @@ -63,7 +63,6 @@ CONFIG_KMOD=y # CONFIG_ARCH_CLPS711X is not set # CONFIG_ARCH_CO285 is not set # CONFIG_ARCH_EBSA110 is not set -# CONFIG_ARCH_CAMELOT is not set CONFIG_ARCH_FOOTBRIDGE=y # CONFIG_ARCH_INTEGRATOR is not set # CONFIG_ARCH_IOP3XX is not set diff --git a/arch/arm/configs/fortunet_defconfig b/arch/arm/configs/fortunet_defconfig index b6f688d850dc..65dc73a88c43 100644 --- a/arch/arm/configs/fortunet_defconfig +++ b/arch/arm/configs/fortunet_defconfig @@ -57,7 +57,6 @@ CONFIG_BASE_SMALL=0 CONFIG_ARCH_CLPS711X=y # CONFIG_ARCH_CO285 is not set # CONFIG_ARCH_EBSA110 is not set -# CONFIG_ARCH_CAMELOT is not set # CONFIG_ARCH_FOOTBRIDGE is not set # CONFIG_ARCH_INTEGRATOR is not set # CONFIG_ARCH_IOP3XX is not set diff --git a/arch/arm/configs/h3600_defconfig b/arch/arm/configs/h3600_defconfig index b9de07de80fe..7a0da0b7facb 100644 --- a/arch/arm/configs/h3600_defconfig +++ b/arch/arm/configs/h3600_defconfig @@ -65,7 +65,6 @@ CONFIG_OBSOLETE_MODPARM=y # CONFIG_ARCH_CLPS711X is not set # CONFIG_ARCH_CO285 is not set # CONFIG_ARCH_EBSA110 is not set -# CONFIG_ARCH_CAMELOT is not set # CONFIG_ARCH_FOOTBRIDGE is not set # CONFIG_ARCH_INTEGRATOR is not set # CONFIG_ARCH_IOP3XX is not set diff --git a/arch/arm/configs/h7201_defconfig b/arch/arm/configs/h7201_defconfig index 39c13a354541..116920aecef7 100644 --- a/arch/arm/configs/h7201_defconfig +++ b/arch/arm/configs/h7201_defconfig @@ -60,7 +60,6 @@ CONFIG_KMOD=y # CONFIG_ARCH_CLPS711X is not set # CONFIG_ARCH_CO285 is not set # CONFIG_ARCH_EBSA110 is not set -# CONFIG_ARCH_CAMELOT is not set # CONFIG_ARCH_FOOTBRIDGE is not set # CONFIG_ARCH_INTEGRATOR is not set # CONFIG_ARCH_IOP3XX is not set diff --git a/arch/arm/configs/h7202_defconfig b/arch/arm/configs/h7202_defconfig index fbf5c244c696..9d62ed16bf57 100644 --- a/arch/arm/configs/h7202_defconfig +++ b/arch/arm/configs/h7202_defconfig @@ -63,7 +63,6 @@ CONFIG_KMOD=y # CONFIG_ARCH_CLPS711X is not set # CONFIG_ARCH_CO285 is not set # CONFIG_ARCH_EBSA110 is not set -# CONFIG_ARCH_CAMELOT is not set # CONFIG_ARCH_FOOTBRIDGE is not set # CONFIG_ARCH_INTEGRATOR is not set # CONFIG_ARCH_IOP3XX is not set diff --git a/arch/arm/configs/hackkit_defconfig b/arch/arm/configs/hackkit_defconfig index fb41a36a5a68..a45b57582b86 100644 --- a/arch/arm/configs/hackkit_defconfig +++ b/arch/arm/configs/hackkit_defconfig @@ -66,7 +66,6 @@ CONFIG_KMOD=y # CONFIG_ARCH_CLPS711X is not set # CONFIG_ARCH_CO285 is not set # CONFIG_ARCH_EBSA110 is not set -# CONFIG_ARCH_CAMELOT is not set # CONFIG_ARCH_FOOTBRIDGE is not set # CONFIG_ARCH_INTEGRATOR is not set # CONFIG_ARCH_IOP3XX is not set diff --git a/arch/arm/configs/integrator_defconfig b/arch/arm/configs/integrator_defconfig index 27ee76825254..d1ba7fdde818 100644 --- a/arch/arm/configs/integrator_defconfig +++ b/arch/arm/configs/integrator_defconfig @@ -65,7 +65,6 @@ CONFIG_KMOD=y # CONFIG_ARCH_CLPS711X is not set # CONFIG_ARCH_CO285 is not set # CONFIG_ARCH_EBSA110 is not set -# CONFIG_ARCH_CAMELOT is not set # CONFIG_ARCH_FOOTBRIDGE is not set CONFIG_ARCH_INTEGRATOR=y # CONFIG_ARCH_IOP3XX is not set diff --git a/arch/arm/configs/iq31244_defconfig b/arch/arm/configs/iq31244_defconfig index e71443b97390..c07628ceaf0c 100644 --- a/arch/arm/configs/iq31244_defconfig +++ b/arch/arm/configs/iq31244_defconfig @@ -65,7 +65,6 @@ CONFIG_KMOD=y # CONFIG_ARCH_CLPS711X is not set # CONFIG_ARCH_CO285 is not set # CONFIG_ARCH_EBSA110 is not set -# CONFIG_ARCH_CAMELOT is not set # CONFIG_ARCH_FOOTBRIDGE is not set # CONFIG_ARCH_INTEGRATOR is not set CONFIG_ARCH_IOP3XX=y diff --git a/arch/arm/configs/iq80321_defconfig b/arch/arm/configs/iq80321_defconfig index ab5ad23b27da..18fa1615fdfd 100644 --- a/arch/arm/configs/iq80321_defconfig +++ b/arch/arm/configs/iq80321_defconfig @@ -64,7 +64,6 @@ CONFIG_KMOD=y # CONFIG_ARCH_CLPS711X is not set # CONFIG_ARCH_CO285 is not set # CONFIG_ARCH_EBSA110 is not set -# CONFIG_ARCH_CAMELOT is not set # CONFIG_ARCH_FOOTBRIDGE is not set # CONFIG_ARCH_INTEGRATOR is not set CONFIG_ARCH_IOP3XX=y diff --git a/arch/arm/configs/iq80331_defconfig b/arch/arm/configs/iq80331_defconfig index bb536133ef87..f50035de1fff 100644 --- a/arch/arm/configs/iq80331_defconfig +++ b/arch/arm/configs/iq80331_defconfig @@ -64,7 +64,6 @@ CONFIG_KMOD=y # CONFIG_ARCH_CLPS711X is not set # CONFIG_ARCH_CO285 is not set # CONFIG_ARCH_EBSA110 is not set -# CONFIG_ARCH_CAMELOT is not set # CONFIG_ARCH_FOOTBRIDGE is not set # CONFIG_ARCH_INTEGRATOR is not set CONFIG_ARCH_IOP3XX=y diff --git a/arch/arm/configs/iq80332_defconfig b/arch/arm/configs/iq80332_defconfig index 305f01f3a729..18b3f372ed68 100644 --- a/arch/arm/configs/iq80332_defconfig +++ b/arch/arm/configs/iq80332_defconfig @@ -64,7 +64,6 @@ CONFIG_KMOD=y # CONFIG_ARCH_CLPS711X is not set # CONFIG_ARCH_CO285 is not set # CONFIG_ARCH_EBSA110 is not set -# CONFIG_ARCH_CAMELOT is not set # CONFIG_ARCH_FOOTBRIDGE is not set # CONFIG_ARCH_INTEGRATOR is not set CONFIG_ARCH_IOP3XX=y diff --git a/arch/arm/configs/ixdp2400_defconfig b/arch/arm/configs/ixdp2400_defconfig index e6a4d2656fe5..d9d6bb86a6fa 100644 --- a/arch/arm/configs/ixdp2400_defconfig +++ b/arch/arm/configs/ixdp2400_defconfig @@ -86,7 +86,6 @@ CONFIG_DEFAULT_IOSCHED="anticipatory" # CONFIG_ARCH_CLPS711X is not set # CONFIG_ARCH_CO285 is not set # CONFIG_ARCH_EBSA110 is not set -# CONFIG_ARCH_CAMELOT is not set # CONFIG_ARCH_FOOTBRIDGE is not set # CONFIG_ARCH_INTEGRATOR is not set # CONFIG_ARCH_IOP3XX is not set diff --git a/arch/arm/configs/ixdp2401_defconfig b/arch/arm/configs/ixdp2401_defconfig index 5572cf95d5f8..2dc9d499c7d7 100644 --- a/arch/arm/configs/ixdp2401_defconfig +++ b/arch/arm/configs/ixdp2401_defconfig @@ -86,7 +86,6 @@ CONFIG_DEFAULT_IOSCHED="anticipatory" # CONFIG_ARCH_CLPS711X is not set # CONFIG_ARCH_CO285 is not set # CONFIG_ARCH_EBSA110 is not set -# CONFIG_ARCH_CAMELOT is not set # CONFIG_ARCH_FOOTBRIDGE is not set # CONFIG_ARCH_INTEGRATOR is not set # CONFIG_ARCH_IOP3XX is not set diff --git a/arch/arm/configs/ixdp2800_defconfig b/arch/arm/configs/ixdp2800_defconfig index 0fddbde85835..4248123815e9 100644 --- a/arch/arm/configs/ixdp2800_defconfig +++ b/arch/arm/configs/ixdp2800_defconfig @@ -86,7 +86,6 @@ CONFIG_DEFAULT_IOSCHED="anticipatory" # CONFIG_ARCH_CLPS711X is not set # CONFIG_ARCH_CO285 is not set # CONFIG_ARCH_EBSA110 is not set -# CONFIG_ARCH_CAMELOT is not set # CONFIG_ARCH_FOOTBRIDGE is not set # CONFIG_ARCH_INTEGRATOR is not set # CONFIG_ARCH_IOP3XX is not set diff --git a/arch/arm/configs/ixdp2801_defconfig b/arch/arm/configs/ixdp2801_defconfig index 89b9aa06aa91..ea8f4b478fa3 100644 --- a/arch/arm/configs/ixdp2801_defconfig +++ b/arch/arm/configs/ixdp2801_defconfig @@ -86,7 +86,6 @@ CONFIG_DEFAULT_IOSCHED="anticipatory" # CONFIG_ARCH_CLPS711X is not set # CONFIG_ARCH_CO285 is not set # CONFIG_ARCH_EBSA110 is not set -# CONFIG_ARCH_CAMELOT is not set # CONFIG_ARCH_FOOTBRIDGE is not set # CONFIG_ARCH_INTEGRATOR is not set # CONFIG_ARCH_IOP3XX is not set diff --git a/arch/arm/configs/ixp4xx_defconfig b/arch/arm/configs/ixp4xx_defconfig index 613afab62720..4975b914f923 100644 --- a/arch/arm/configs/ixp4xx_defconfig +++ b/arch/arm/configs/ixp4xx_defconfig @@ -85,7 +85,6 @@ CONFIG_DEFAULT_IOSCHED="anticipatory" # CONFIG_ARCH_CLPS711X is not set # CONFIG_ARCH_CO285 is not set # CONFIG_ARCH_EBSA110 is not set -# CONFIG_ARCH_CAMELOT is not set # CONFIG_ARCH_FOOTBRIDGE is not set # CONFIG_ARCH_INTEGRATOR is not set # CONFIG_ARCH_IOP3XX is not set diff --git a/arch/arm/configs/jornada720_defconfig b/arch/arm/configs/jornada720_defconfig index b88aeba82bc0..ad1048db96fb 100644 --- a/arch/arm/configs/jornada720_defconfig +++ b/arch/arm/configs/jornada720_defconfig @@ -63,7 +63,6 @@ CONFIG_KMOD=y # CONFIG_ARCH_CLPS711X is not set # CONFIG_ARCH_CO285 is not set # CONFIG_ARCH_EBSA110 is not set -# CONFIG_ARCH_CAMELOT is not set # CONFIG_ARCH_FOOTBRIDGE is not set # CONFIG_ARCH_INTEGRATOR is not set # CONFIG_ARCH_IOP3XX is not set diff --git a/arch/arm/configs/lart_defconfig b/arch/arm/configs/lart_defconfig index 7033829ed145..c3a932844160 100644 --- a/arch/arm/configs/lart_defconfig +++ b/arch/arm/configs/lart_defconfig @@ -62,7 +62,6 @@ CONFIG_KMOD=y # CONFIG_ARCH_CLPS711X is not set # CONFIG_ARCH_CO285 is not set # CONFIG_ARCH_EBSA110 is not set -# CONFIG_ARCH_CAMELOT is not set # CONFIG_ARCH_FOOTBRIDGE is not set # CONFIG_ARCH_INTEGRATOR is not set # CONFIG_ARCH_IOP3XX is not set diff --git a/arch/arm/configs/lpd7a400_defconfig b/arch/arm/configs/lpd7a400_defconfig index d64706d3ff35..67eaa26c2647 100644 --- a/arch/arm/configs/lpd7a400_defconfig +++ b/arch/arm/configs/lpd7a400_defconfig @@ -60,7 +60,6 @@ CONFIG_BASE_SMALL=0 # CONFIG_ARCH_CLPS711X is not set # CONFIG_ARCH_CO285 is not set # CONFIG_ARCH_EBSA110 is not set -# CONFIG_ARCH_CAMELOT is not set # CONFIG_ARCH_FOOTBRIDGE is not set # CONFIG_ARCH_INTEGRATOR is not set # CONFIG_ARCH_IOP3XX is not set diff --git a/arch/arm/configs/lpd7a404_defconfig b/arch/arm/configs/lpd7a404_defconfig index 87cbedfb303f..208d591ebfce 100644 --- a/arch/arm/configs/lpd7a404_defconfig +++ b/arch/arm/configs/lpd7a404_defconfig @@ -60,7 +60,6 @@ CONFIG_BASE_SMALL=0 # CONFIG_ARCH_CLPS711X is not set # CONFIG_ARCH_CO285 is not set # CONFIG_ARCH_EBSA110 is not set -# CONFIG_ARCH_CAMELOT is not set # CONFIG_ARCH_FOOTBRIDGE is not set # CONFIG_ARCH_INTEGRATOR is not set # CONFIG_ARCH_IOP3XX is not set diff --git a/arch/arm/configs/lubbock_defconfig b/arch/arm/configs/lubbock_defconfig index 4bc8717c6f57..81daadcbe0ba 100644 --- a/arch/arm/configs/lubbock_defconfig +++ b/arch/arm/configs/lubbock_defconfig @@ -63,7 +63,6 @@ CONFIG_OBSOLETE_MODPARM=y # CONFIG_ARCH_CLPS711X is not set # CONFIG_ARCH_CO285 is not set # CONFIG_ARCH_EBSA110 is not set -# CONFIG_ARCH_CAMELOT is not set # CONFIG_ARCH_FOOTBRIDGE is not set # CONFIG_ARCH_INTEGRATOR is not set # CONFIG_ARCH_IOP3XX is not set diff --git a/arch/arm/configs/lusl7200_defconfig b/arch/arm/configs/lusl7200_defconfig index 3ca64cabc92c..42f6a77bc3c0 100644 --- a/arch/arm/configs/lusl7200_defconfig +++ b/arch/arm/configs/lusl7200_defconfig @@ -62,7 +62,6 @@ CONFIG_KMOD=y # CONFIG_ARCH_CLPS711X is not set # CONFIG_ARCH_CO285 is not set # CONFIG_ARCH_EBSA110 is not set -# CONFIG_ARCH_CAMELOT is not set # CONFIG_ARCH_FOOTBRIDGE is not set # CONFIG_ARCH_INTEGRATOR is not set # CONFIG_ARCH_IOP3XX is not set diff --git a/arch/arm/configs/mainstone_defconfig b/arch/arm/configs/mainstone_defconfig index 153d68594beb..b112bd75bda2 100644 --- a/arch/arm/configs/mainstone_defconfig +++ b/arch/arm/configs/mainstone_defconfig @@ -63,7 +63,6 @@ CONFIG_OBSOLETE_MODPARM=y # CONFIG_ARCH_CLPS711X is not set # CONFIG_ARCH_CO285 is not set # CONFIG_ARCH_EBSA110 is not set -# CONFIG_ARCH_CAMELOT is not set # CONFIG_ARCH_FOOTBRIDGE is not set # CONFIG_ARCH_INTEGRATOR is not set # CONFIG_ARCH_IOP3XX is not set diff --git a/arch/arm/configs/mx1ads_defconfig b/arch/arm/configs/mx1ads_defconfig index 6517d167acf0..d16f6cd6e039 100644 --- a/arch/arm/configs/mx1ads_defconfig +++ b/arch/arm/configs/mx1ads_defconfig @@ -63,7 +63,6 @@ CONFIG_KMOD=y # CONFIG_ARCH_CLPS711X is not set # CONFIG_ARCH_CO285 is not set # CONFIG_ARCH_EBSA110 is not set -# CONFIG_ARCH_CAMELOT is not set # CONFIG_ARCH_FOOTBRIDGE is not set # CONFIG_ARCH_INTEGRATOR is not set # CONFIG_ARCH_IOP3XX is not set diff --git a/arch/arm/configs/neponset_defconfig b/arch/arm/configs/neponset_defconfig index 7fb1f7c7bf43..3d35255c64ed 100644 --- a/arch/arm/configs/neponset_defconfig +++ b/arch/arm/configs/neponset_defconfig @@ -65,7 +65,6 @@ CONFIG_OBSOLETE_MODPARM=y # CONFIG_ARCH_CLPS711X is not set # CONFIG_ARCH_CO285 is not set # CONFIG_ARCH_EBSA110 is not set -# CONFIG_ARCH_CAMELOT is not set # CONFIG_ARCH_FOOTBRIDGE is not set # CONFIG_ARCH_INTEGRATOR is not set # CONFIG_ARCH_IOP3XX is not set diff --git a/arch/arm/configs/netwinder_defconfig b/arch/arm/configs/netwinder_defconfig index 6e81acf94c2f..2cae1ead9f9b 100644 --- a/arch/arm/configs/netwinder_defconfig +++ b/arch/arm/configs/netwinder_defconfig @@ -58,7 +58,6 @@ CONFIG_BASE_SMALL=0 # CONFIG_ARCH_CLPS711X is not set # CONFIG_ARCH_CO285 is not set # CONFIG_ARCH_EBSA110 is not set -# CONFIG_ARCH_CAMELOT is not set CONFIG_ARCH_FOOTBRIDGE=y # CONFIG_ARCH_INTEGRATOR is not set # CONFIG_ARCH_IOP3XX is not set diff --git a/arch/arm/configs/omap_h2_1610_defconfig b/arch/arm/configs/omap_h2_1610_defconfig index 529f0f72e1e9..ee3ecbd9002d 100644 --- a/arch/arm/configs/omap_h2_1610_defconfig +++ b/arch/arm/configs/omap_h2_1610_defconfig @@ -85,7 +85,6 @@ CONFIG_DEFAULT_IOSCHED="anticipatory" # CONFIG_ARCH_CLPS711X is not set # CONFIG_ARCH_CO285 is not set # CONFIG_ARCH_EBSA110 is not set -# CONFIG_ARCH_CAMELOT is not set # CONFIG_ARCH_FOOTBRIDGE is not set # CONFIG_ARCH_INTEGRATOR is not set # CONFIG_ARCH_IOP3XX is not set diff --git a/arch/arm/configs/pleb_defconfig b/arch/arm/configs/pleb_defconfig index 10fec890578d..24e8bdd4cb91 100644 --- a/arch/arm/configs/pleb_defconfig +++ b/arch/arm/configs/pleb_defconfig @@ -63,7 +63,6 @@ CONFIG_KMOD=y # CONFIG_ARCH_CLPS711X is not set # CONFIG_ARCH_CO285 is not set # CONFIG_ARCH_EBSA110 is not set -# CONFIG_ARCH_CAMELOT is not set # CONFIG_ARCH_FOOTBRIDGE is not set # CONFIG_ARCH_INTEGRATOR is not set # CONFIG_ARCH_IOP3XX is not set diff --git a/arch/arm/configs/pxa255-idp_defconfig b/arch/arm/configs/pxa255-idp_defconfig index 21c327883d8c..b71d31a4bb56 100644 --- a/arch/arm/configs/pxa255-idp_defconfig +++ b/arch/arm/configs/pxa255-idp_defconfig @@ -63,7 +63,6 @@ CONFIG_OBSOLETE_MODPARM=y # CONFIG_ARCH_CLPS711X is not set # CONFIG_ARCH_CO285 is not set # CONFIG_ARCH_EBSA110 is not set -# CONFIG_ARCH_CAMELOT is not set # CONFIG_ARCH_FOOTBRIDGE is not set # CONFIG_ARCH_INTEGRATOR is not set # CONFIG_ARCH_IOP3XX is not set diff --git a/arch/arm/configs/realview_defconfig b/arch/arm/configs/realview_defconfig index 0485b2f1cc20..3f1ec4e304f7 100644 --- a/arch/arm/configs/realview_defconfig +++ b/arch/arm/configs/realview_defconfig @@ -65,7 +65,6 @@ CONFIG_OBSOLETE_MODPARM=y # CONFIG_ARCH_CLPS711X is not set # CONFIG_ARCH_CO285 is not set # CONFIG_ARCH_EBSA110 is not set -# CONFIG_ARCH_CAMELOT is not set # CONFIG_ARCH_FOOTBRIDGE is not set # CONFIG_ARCH_INTEGRATOR is not set # CONFIG_ARCH_IOP3XX is not set diff --git a/arch/arm/configs/rpc_defconfig b/arch/arm/configs/rpc_defconfig index 19184c1010ad..b498afdc03b6 100644 --- a/arch/arm/configs/rpc_defconfig +++ b/arch/arm/configs/rpc_defconfig @@ -66,7 +66,6 @@ CONFIG_KMOD=y # CONFIG_ARCH_CLPS711X is not set # CONFIG_ARCH_CO285 is not set # CONFIG_ARCH_EBSA110 is not set -# CONFIG_ARCH_CAMELOT is not set # CONFIG_ARCH_FOOTBRIDGE is not set # CONFIG_ARCH_INTEGRATOR is not set # CONFIG_ARCH_IOP3XX is not set diff --git a/arch/arm/configs/s3c2410_defconfig b/arch/arm/configs/s3c2410_defconfig index 3f97590c91f2..33f31080a98c 100644 --- a/arch/arm/configs/s3c2410_defconfig +++ b/arch/arm/configs/s3c2410_defconfig @@ -85,7 +85,6 @@ CONFIG_DEFAULT_IOSCHED="anticipatory" # CONFIG_ARCH_CLPS711X is not set # CONFIG_ARCH_CO285 is not set # CONFIG_ARCH_EBSA110 is not set -# CONFIG_ARCH_CAMELOT is not set # CONFIG_ARCH_FOOTBRIDGE is not set # CONFIG_ARCH_INTEGRATOR is not set # CONFIG_ARCH_IOP3XX is not set diff --git a/arch/arm/configs/shannon_defconfig b/arch/arm/configs/shannon_defconfig index e3facc4fe792..d052c8f80515 100644 --- a/arch/arm/configs/shannon_defconfig +++ b/arch/arm/configs/shannon_defconfig @@ -62,7 +62,6 @@ CONFIG_OBSOLETE_MODPARM=y # CONFIG_ARCH_CLPS711X is not set # CONFIG_ARCH_CO285 is not set # CONFIG_ARCH_EBSA110 is not set -# CONFIG_ARCH_CAMELOT is not set # CONFIG_ARCH_FOOTBRIDGE is not set # CONFIG_ARCH_INTEGRATOR is not set # CONFIG_ARCH_IOP3XX is not set diff --git a/arch/arm/configs/shark_defconfig b/arch/arm/configs/shark_defconfig index 271823f0d708..c48d17062262 100644 --- a/arch/arm/configs/shark_defconfig +++ b/arch/arm/configs/shark_defconfig @@ -66,7 +66,6 @@ CONFIG_KMOD=y # CONFIG_ARCH_CLPS711X is not set # CONFIG_ARCH_CO285 is not set # CONFIG_ARCH_EBSA110 is not set -# CONFIG_ARCH_CAMELOT is not set # CONFIG_ARCH_FOOTBRIDGE is not set # CONFIG_ARCH_INTEGRATOR is not set # CONFIG_ARCH_IOP3XX is not set diff --git a/arch/arm/configs/simpad_defconfig b/arch/arm/configs/simpad_defconfig index 5373eeb7d578..2e5a616cc98d 100644 --- a/arch/arm/configs/simpad_defconfig +++ b/arch/arm/configs/simpad_defconfig @@ -64,7 +64,6 @@ CONFIG_KMOD=y # CONFIG_ARCH_CLPS711X is not set # CONFIG_ARCH_CO285 is not set # CONFIG_ARCH_EBSA110 is not set -# CONFIG_ARCH_CAMELOT is not set # CONFIG_ARCH_FOOTBRIDGE is not set # CONFIG_ARCH_INTEGRATOR is not set # CONFIG_ARCH_IOP3XX is not set diff --git a/arch/arm/configs/smdk2410_defconfig b/arch/arm/configs/smdk2410_defconfig index 2c60865fda19..4d123d33c7df 100644 --- a/arch/arm/configs/smdk2410_defconfig +++ b/arch/arm/configs/smdk2410_defconfig @@ -58,7 +58,6 @@ CONFIG_BASE_SMALL=0 # CONFIG_ARCH_CLPS711X is not set # CONFIG_ARCH_CO285 is not set # CONFIG_ARCH_EBSA110 is not set -# CONFIG_ARCH_CAMELOT is not set # CONFIG_ARCH_FOOTBRIDGE is not set # CONFIG_ARCH_INTEGRATOR is not set # CONFIG_ARCH_IOP3XX is not set diff --git a/arch/arm/configs/spitz_defconfig b/arch/arm/configs/spitz_defconfig index 9895539533d6..d1ace3abfd8a 100644 --- a/arch/arm/configs/spitz_defconfig +++ b/arch/arm/configs/spitz_defconfig @@ -87,7 +87,6 @@ CONFIG_DEFAULT_IOSCHED="anticipatory" # CONFIG_ARCH_CLPS711X is not set # CONFIG_ARCH_CO285 is not set # CONFIG_ARCH_EBSA110 is not set -# CONFIG_ARCH_CAMELOT is not set # CONFIG_ARCH_FOOTBRIDGE is not set # CONFIG_ARCH_INTEGRATOR is not set # CONFIG_ARCH_IOP3XX is not set diff --git a/arch/arm/configs/versatile_defconfig b/arch/arm/configs/versatile_defconfig index d72f2c754268..2687a225aa6a 100644 --- a/arch/arm/configs/versatile_defconfig +++ b/arch/arm/configs/versatile_defconfig @@ -64,7 +64,6 @@ CONFIG_KMOD=y # CONFIG_ARCH_CLPS711X is not set # CONFIG_ARCH_CO285 is not set # CONFIG_ARCH_EBSA110 is not set -# CONFIG_ARCH_CAMELOT is not set # CONFIG_ARCH_FOOTBRIDGE is not set # CONFIG_ARCH_INTEGRATOR is not set # CONFIG_ARCH_IOP3XX is not set diff --git a/arch/arm/kernel/irq.c b/arch/arm/kernel/irq.c index b5645c4462cf..1d50d2b98f55 100644 --- a/arch/arm/kernel/irq.c +++ b/arch/arm/kernel/irq.c @@ -710,7 +710,8 @@ int setup_irq(unsigned int irq, struct irqaction *new) desc->pending = 0; desc->disable_depth = 1; - if (new->flags & SA_TRIGGER_MASK) { + if (new->flags & SA_TRIGGER_MASK && + desc->chip->set_type) { unsigned int type = new->flags & SA_TRIGGER_MASK; desc->chip->set_type(irq, type); } diff --git a/arch/arm/mach-at91rm9200/Kconfig b/arch/arm/mach-at91rm9200/Kconfig new file mode 100644 index 000000000000..4b7218fc3eb1 --- /dev/null +++ b/arch/arm/mach-at91rm9200/Kconfig @@ -0,0 +1,54 @@ +if ARCH_AT91RM9200 + +menu "AT91RM9200 Implementations" + +comment "AT91RM9200 Board Type" + +config ARCH_AT91RM9200DK + bool "Atmel AT91RM9200-DK Development board" + depends on ARCH_AT91RM9200 + help + Select this if you are using Atmel's AT91RM9200-DK Development board + +config MACH_AT91RM9200EK + bool "Atmel AT91RM9200-EK Evaluation Kit" + depends on ARCH_AT91RM9200 + help + Select this if you are using Atmel's AT91RM9200-EK Evaluation Kit + +config MACH_CSB337 + bool "Cogent CSB337 board" + depends on ARCH_AT91RM9200 + help + Select this if you are using Cogent's CSB337 board + +config MACH_CSB637 + bool "Cogent CSB637 board" + depends on ARCH_AT91RM9200 + help + Select this if you are using Cogent's CSB637 board + +config MACH_CARMEVA + bool "Conitec's ARM&EVA" + depends on ARCH_AT91RM9200 + help + Select this if you are using Conitec's AT91RM9200-MCU-Module + +config MACH_KB9200 + bool "KwikByte's KB920x" + depends on ARCH_AT91RM9200 + help + Select this if you are using KwikByte's KB920x board + + +comment "AT91RM9200 Feature Selections" + +config AT91_PROGRAMMABLE_CLOCKS + bool "Programmable Clocks" + help + Select this if you need to program one or more of the PCK0..PCK3 + programmable clock outputs. + +endmenu + +endif diff --git a/arch/arm/mach-at91rm9200/Makefile b/arch/arm/mach-at91rm9200/Makefile new file mode 100644 index 000000000000..1f2805ca6e21 --- /dev/null +++ b/arch/arm/mach-at91rm9200/Makefile @@ -0,0 +1,27 @@ +# +# Makefile for the linux kernel. +# + +obj-y := clock.o irq.o time.o gpio.o common.o devices.o +obj-m := +obj-n := +obj- := + +# Board-specific support +#obj-$(CONFIG_ARCH_AT91RM9200DK) += board-dk.o +#obj-$(CONFIG_MACH_AT91RM9200EK) += board-ek.o +#obj-$(CONFIG_MACH_CSB337) += board-csb337.o +#obj-$(CONFIG_MACH_CSB637) += board-csb637.o +#obj-$(CONFIG_MACH_CARMEVA) += board-carmeva.o +#obj-$(CONFIG_MACH_KB9200) += board-kb9202.o + +# LEDs support +#led-$(CONFIG_ARCH_AT91RM9200DK) += leds.o +#led-$(CONFIG_MACH_AT91RM9200EK) += leds.o +#led-$(CONFIG_MACH_CSB337) += leds.o +#led-$(CONFIG_MACH_CSB637) += leds.o +#led-$(CONFIG_MACH_KB9200) += leds.o +obj-$(CONFIG_LEDS) += $(led-y) + +# VGA support +#obj-$(CONFIG_FB_S1D13XXX) += ics1523.o diff --git a/arch/arm/mach-at91rm9200/Makefile.boot b/arch/arm/mach-at91rm9200/Makefile.boot new file mode 100644 index 000000000000..e667dcc7cd34 --- /dev/null +++ b/arch/arm/mach-at91rm9200/Makefile.boot @@ -0,0 +1,9 @@ +# Note: the following conditions must always be true: +# ZRELADDR == virt_to_phys(TEXTADDR) +# PARAMS_PHYS must be within 4MB of ZRELADDR +# INITRD_PHYS must be in RAM + + zreladdr-y := 0x20008000 +params_phys-y := 0x20000100 +initrd_phys-y := 0x20410000 + diff --git a/arch/arm/mach-at91rm9200/clock.c b/arch/arm/mach-at91rm9200/clock.c new file mode 100644 index 000000000000..ec8195a2a3cc --- /dev/null +++ b/arch/arm/mach-at91rm9200/clock.c @@ -0,0 +1,620 @@ +/* + * linux/arch/arm/mach-at91rm9200/clock.c + * + * Copyright (C) 2005 David Brownell + * Copyright (C) 2005 Ivan Kokshaysky + * + * This program is free software; you can redistribute it and/or modify + * it under the terms of the GNU General Public License as published by + * the Free Software Foundation; either version 2 of the License, or + * (at your option) any later version. + */ + +#include <linux/module.h> +#include <linux/kernel.h> +#include <linux/init.h> +#include <linux/fs.h> +#include <linux/debugfs.h> +#include <linux/seq_file.h> +#include <linux/list.h> +#include <linux/errno.h> +#include <linux/err.h> +#include <linux/spinlock.h> +#include <linux/delay.h> +#include <linux/clk.h> + +#include <asm/semaphore.h> +#include <asm/io.h> +#include <asm/mach-types.h> + +#include <asm/arch/hardware.h> +#include <asm/arch/board.h> /* for master clock global */ + +#include "generic.h" + +#undef DEBUG + +/* + * There's a lot more which can be done with clocks, including cpufreq + * integration, slow clock mode support (for system suspend), letting + * PLLB be used at other rates (on boards that don't need USB), etc. + */ + +struct clk { + const char *name; + unsigned long rate_hz; + struct clk *parent; + u32 pmc_mask; + void (*mode)(struct clk *, int); + unsigned id:2; /* PCK0..3, or 32k/main/a/b */ + unsigned primary:1; + unsigned pll:1; + unsigned programmable:1; + u16 users; +}; + +static spinlock_t clk_lock; +static u32 at91_pllb_usb_init; + +/* + * Four primary clock sources: two crystal oscillators (32K, main), and + * two PLLs. PLLA usually runs the master clock; and PLLB must run at + * 48 MHz (unless no USB function clocks are needed). The main clock and + * both PLLs are turned off to run in "slow clock mode" (system suspend). + */ +static struct clk clk32k = { + .name = "clk32k", + .rate_hz = AT91_SLOW_CLOCK, + .users = 1, /* always on */ + .id = 0, + .primary = 1, +}; +static struct clk main_clk = { + .name = "main", + .pmc_mask = 1 << 0, /* in PMC_SR */ + .users = 1, + .id = 1, + .primary = 1, +}; +static struct clk plla = { + .name = "plla", + .parent = &main_clk, + .pmc_mask = 1 << 1, /* in PMC_SR */ + .id = 2, + .primary = 1, + .pll = 1, +}; + +static void pllb_mode(struct clk *clk, int is_on) +{ + u32 value; + + if (is_on) { + is_on = AT91_PMC_LOCKB; + value = at91_pllb_usb_init; + } else + value = 0; + + at91_sys_write(AT91_CKGR_PLLBR, value); + + do { + cpu_relax(); + } while ((at91_sys_read(AT91_PMC_SR) & AT91_PMC_LOCKB) != is_on); +} + +static struct clk pllb = { + .name = "pllb", + .parent = &main_clk, + .pmc_mask = 1 << 2, /* in PMC_SR */ + .mode = pllb_mode, + .id = 3, + .primary = 1, + .pll = 1, +}; + +static void pmc_sys_mode(struct clk *clk, int is_on) +{ + if (is_on) + at91_sys_write(AT91_PMC_SCER, clk->pmc_mask); + else + at91_sys_write(AT91_PMC_SCDR, clk->pmc_mask); +} + +/* USB function clocks (PLLB must be 48 MHz) */ +static struct clk udpck = { + .name = "udpck", + .parent = &pllb, + .pmc_mask = AT91_PMC_UDP, + .mode = pmc_sys_mode, +}; +static struct clk uhpck = { + .name = "uhpck", + .parent = &pllb, + .pmc_mask = AT91_PMC_UHP, + .mode = pmc_sys_mode, +}; + +#ifdef CONFIG_AT91_PROGRAMMABLE_CLOCKS +/* + * The four programmable clocks can be parented by any primary clock. + * You must configure pin multiplexing to bring these signals out. + */ +static struct clk pck0 = { + .name = "pck0", + .pmc_mask = AT91_PMC_PCK0, + .mode = pmc_sys_mode, + .programmable = 1, + .id = 0, +}; +static struct clk pck1 = { + .name = "pck1", + .pmc_mask = AT91_PMC_PCK1, + .mode = pmc_sys_mode, + .programmable = 1, + .id = 1, +}; +static struct clk pck2 = { + .name = "pck2", + .pmc_mask = AT91_PMC_PCK2, + .mode = pmc_sys_mode, + .programmable = 1, + .id = 2, +}; +static struct clk pck3 = { + .name = "pck3", + .pmc_mask = AT91_PMC_PCK3, + .mode = pmc_sys_mode, + .programmable = 1, + .id = 3, +}; +#endif /* CONFIG_AT91_PROGRAMMABLE_CLOCKS */ + + +/* + * The master clock is divided from the CPU clock (by 1-4). It's used for + * memory, interfaces to on-chip peripherals, the AIC, and sometimes more + * (e.g baud rate generation). It's sourced from one of the primary clocks. + */ +static struct clk mck = { + .name = "mck", + .pmc_mask = 1 << 3, /* in PMC_SR */ + .users = 1, /* (must be) always on */ +}; + +static void pmc_periph_mode(struct clk *clk, int is_on) +{ + if (is_on) + at91_sys_write(AT91_PMC_PCER, clk->pmc_mask); + else + at91_sys_write(AT91_PMC_PCDR, clk->pmc_mask); +} + +static struct clk udc_clk = { + .name = "udc_clk", + .parent = &mck, + .pmc_mask = 1 << AT91_ID_UDP, + .mode = pmc_periph_mode, +}; +static struct clk ohci_clk = { + .name = "ohci_clk", + .parent = &mck, + .pmc_mask = 1 << AT91_ID_UHP, + .mode = pmc_periph_mode, +}; + +static struct clk *const clock_list[] = { + /* four primary clocks -- MUST BE FIRST! */ + &clk32k, + &main_clk, + &plla, + &pllb, + + /* PLLB children (USB) */ + &udpck, + &uhpck, + +#ifdef CONFIG_AT91_PROGRAMMABLE_CLOCKS + /* programmable clocks */ + &pck0, + &pck1, + &pck2, + &pck3, +#endif /* CONFIG_AT91_PROGRAMMABLE_CLOCKS */ + + /* MCK and peripherals */ + &mck, + // usart0..usart3 + // mmc + &udc_clk, + // i2c + // spi + // ssc0..ssc2 + // tc0..tc5 + &ohci_clk, + // ether +}; + + +/* clocks are all static for now; no refcounting necessary */ +struct clk *clk_get(struct device *dev, const char *id) +{ + int i; + + for (i = 0; i < ARRAY_SIZE(clock_list); i++) { + if (strcmp(id, clock_list[i]->name) == 0) + return clock_list[i]; + } + + return ERR_PTR(-ENOENT); +} +EXPORT_SYMBOL(clk_get); + +void clk_put(struct clk *clk) +{ +} +EXPORT_SYMBOL(clk_put); + +static void __clk_enable(struct clk *clk) +{ + if (clk->parent) + __clk_enable(clk->parent); + if (clk->users++ == 0 && clk->mode) + clk->mode(clk, 1); +} + +int clk_enable(struct clk *clk) +{ + unsigned long flags; + + spin_lock_irqsave(&clk_lock, flags); + __clk_enable(clk); + spin_unlock_irqrestore(&clk_lock, flags); + return 0; +} +EXPORT_SYMBOL(clk_enable); + +static void __clk_disable(struct clk *clk) +{ + BUG_ON(clk->users == 0); + if (--clk->users == 0 && clk->mode) + clk->mode(clk, 0); + if (clk->parent) + __clk_disable(clk->parent); +} + +void clk_disable(struct clk *clk) +{ + unsigned long flags; + + spin_lock_irqsave(&clk_lock, flags); + __clk_disable(clk); + spin_unlock_irqrestore(&clk_lock, flags); +} +EXPORT_SYMBOL(clk_disable); + +unsigned long clk_get_rate(struct clk *clk) +{ + unsigned long flags; + unsigned long rate; + + spin_lock_irqsave(&clk_lock, flags); + for (;;) { + rate = clk->rate_hz; + if (rate || !clk->parent) + break; + clk = clk->parent; + } + spin_unlock_irqrestore(&clk_lock, flags); + return rate; +} +EXPORT_SYMBOL(clk_get_rate); + +/*------------------------------------------------------------------------*/ + +#ifdef CONFIG_AT91_PROGRAMMABLE_CLOCKS + +/* + * For now, only the programmable clocks support reparenting (MCK could + * do this too, with care) or rate changing (the PLLs could do this too, + * ditto MCK but that's more for cpufreq). Drivers may reparent to get + * a better rate match; we don't. + */ + +long clk_round_rate(struct clk *clk, unsigned long rate) +{ + unsigned long flags; + unsigned prescale; + unsigned long actual; + + if (!clk->programmable) + return -EINVAL; + spin_lock_irqsave(&clk_lock, flags); + + actual = clk->parent->rate_hz; + for (prescale = 0; prescale < 7; prescale++) { + if (actual && actual <= rate) + break; + actual >>= 1; + } + + spin_unlock_irqrestore(&clk_lock, flags); + return (prescale < 7) ? actual : -ENOENT; +} +EXPORT_SYMBOL(clk_round_rate); + +int clk_set_rate(struct clk *clk, unsigned long rate) +{ + unsigned long flags; + unsigned prescale; + unsigned long actual; + + if (!clk->programmable) + return -EINVAL; + if (clk->users) + return -EBUSY; + spin_lock_irqsave(&clk_lock, flags); + + actual = clk->parent->rate_hz; + for (prescale = 0; prescale < 7; prescale++) { + if (actual && actual <= rate) { + u32 pckr; + + pckr = at91_sys_read(AT91_PMC_PCKR(clk->id)); + pckr &= 0x03; + pckr |= prescale << 2; + at91_sys_write(AT91_PMC_PCKR(clk->id), pckr); + clk->rate_hz = actual; + break; + } + actual >>= 1; + } + + spin_unlock_irqrestore(&clk_lock, flags); + return (prescale < 7) ? actual : -ENOENT; +} +EXPORT_SYMBOL(clk_set_rate); + +struct clk *clk_get_parent(struct clk *clk) +{ + return clk->parent; +} +EXPORT_SYMBOL(clk_get_parent); + +int clk_set_parent(struct clk *clk, struct clk *parent) +{ + unsigned long flags; + + if (clk->users) + return -EBUSY; + if (!parent->primary || !clk->programmable) + return -EINVAL; + spin_lock_irqsave(&clk_lock, flags); + + clk->rate_hz = parent->rate_hz; + clk->parent = parent; + at91_sys_write(AT91_PMC_PCKR(clk->id), parent->id); + + spin_unlock_irqrestore(&clk_lock, flags); + return 0; +} +EXPORT_SYMBOL(clk_set_parent); + +#endif /* CONFIG_AT91_PROGRAMMABLE_CLOCKS */ + +/*------------------------------------------------------------------------*/ + +#ifdef CONFIG_DEBUG_FS + +static int at91_clk_show(struct seq_file *s, void *unused) +{ + u32 scsr, pcsr, sr; + unsigned i; + + seq_printf(s, "SCSR = %8x\n", scsr = at91_sys_read(AT91_PMC_SCSR)); + seq_printf(s, "PCSR = %8x\n", pcsr = at91_sys_read(AT91_PMC_PCSR)); + + seq_printf(s, "MOR = %8x\n", at91_sys_read(AT91_CKGR_MOR)); + seq_printf(s, "MCFR = %8x\n", at91_sys_read(AT91_CKGR_MCFR)); + seq_printf(s, "PLLA = %8x\n", at91_sys_read(AT91_CKGR_PLLAR)); + seq_printf(s, "PLLB = %8x\n", at91_sys_read(AT91_CKGR_PLLBR)); + + seq_printf(s, "MCKR = %8x\n", at91_sys_read(AT91_PMC_MCKR)); + for (i = 0; i < 4; i++) + seq_printf(s, "PCK%d = %8x\n", i, at91_sys_read(AT91_PMC_PCKR(i))); + seq_printf(s, "SR = %8x\n", sr = at91_sys_read(AT91_PMC_SR)); + + seq_printf(s, "\n"); + + for (i = 0; i < ARRAY_SIZE(clock_list); i++) { + char *state; + struct clk *clk = clock_list[i]; + + if (clk->mode == pmc_sys_mode) + state = (scsr & clk->pmc_mask) ? "on" : "off"; + else if (clk->mode == pmc_periph_mode) + state = (pcsr & clk->pmc_mask) ? "on" : "off"; + else if (clk->pmc_mask) + state = (sr & clk->pmc_mask) ? "on" : "off"; + else if (clk == &clk32k || clk == &main_clk) + state = "on"; + else + state = ""; + + seq_printf(s, "%-10s users=%d %-3s %9ld Hz %s\n", + clk->name, clk->users, state, clk_get_rate(clk), + clk->parent ? clk->parent->name : ""); + } + return 0; +} + +static int at91_clk_open(struct inode *inode, struct file *file) +{ + return single_open(file, at91_clk_show, NULL); +} + +static struct file_operations at91_clk_operations = { + .open = at91_clk_open, + .read = seq_read, + .llseek = seq_lseek, + .release = single_release, +}; + +static int __init at91_clk_debugfs_init(void) +{ + /* /sys/kernel/debug/at91_clk */ + (void) debugfs_create_file("at91_clk", S_IFREG | S_IRUGO, NULL, NULL, &at91_clk_operations); + + return 0; +} +postcore_initcall(at91_clk_debugfs_init); + +#endif + +/*------------------------------------------------------------------------*/ + +static u32 __init at91_pll_rate(struct clk *pll, u32 freq, u32 reg) +{ + unsigned mul, div; + + div = reg & 0xff; + mul = (reg >> 16) & 0x7ff; + if (div && mul) { + freq /= div; + freq *= mul + 1; + } else + freq = 0; + if (pll == &pllb && (reg & (1 << 28))) + freq /= 2; + return freq; +} + +static unsigned __init at91_pll_calc(unsigned main_freq, unsigned out_freq) +{ + unsigned i, div = 0, mul = 0, diff = 1 << 30; + unsigned ret = (out_freq > 155000000) ? 0xbe00 : 0x3e00; + + /* PLL output max 240 MHz (or 180 MHz per errata) */ + if (out_freq > 240000000) + goto fail; + + for (i = 1; i < 256; i++) { + int diff1; + unsigned input, mul1; + + /* + * PLL input between 1MHz and 32MHz per spec, but lower + * frequences seem necessary in some cases so allow 100K. + */ + input = main_freq / i; + if (input < 100000) + continue; + if (input > 32000000) + continue; + + mul1 = out_freq / input; + if (mul1 > 2048) + continue; + if (mul1 < 2) + goto fail; + + diff1 = out_freq - input * mul1; + if (diff1 < 0) + diff1 = -diff1; + if (diff > diff1) { + diff = diff1; + div = i; + mul = mul1; + if (diff == 0) + break; + } + } + if (i == 256 && diff > (out_freq >> 5)) + goto fail; + return ret | ((mul - 1) << 16) | div; +fail: + return 0; +} + +int __init at91_clock_init(unsigned long main_clock) +{ + unsigned tmp, freq, mckr; + + spin_lock_init(&clk_lock); + + /* + * When the bootloader initialized the main oscillator correctly, + * there's no problem using the cycle counter. But if it didn't, + * or when using oscillator bypass mode, we must be told the speed + * of the main clock. + */ + if (!main_clock) { + do { + tmp = at91_sys_read(AT91_CKGR_MCFR); + } while (!(tmp & 0x10000)); + main_clock = (tmp & 0xffff) * (AT91_SLOW_CLOCK / 16); + } + main_clk.rate_hz = main_clock; + + /* report if PLLA is more than mildly overclocked */ + plla.rate_hz = at91_pll_rate(&plla, main_clock, at91_sys_read(AT91_CKGR_PLLAR)); + if (plla.rate_hz > 209000000) + pr_info("Clocks: PLLA overclocked, %ld MHz\n", plla.rate_hz / 1000000); + + /* + * USB clock init: choose 48 MHz PLLB value, turn all clocks off, + * disable 48MHz clock during usb peripheral suspend. + * + * REVISIT: assumes MCK doesn't derive from PLLB! + */ + at91_pllb_usb_init = at91_pll_calc(main_clock, 48000000 * 2) | 0x10000000; + pllb.rate_hz = at91_pll_rate(&pllb, main_clock, at91_pllb_usb_init); + at91_sys_write(AT91_PMC_PCDR, (1 << AT91_ID_UHP) | (1 << AT91_ID_UDP)); + at91_sys_write(AT91_PMC_SCDR, AT91_PMC_UHP | AT91_PMC_UDP); + at91_sys_write(AT91_CKGR_PLLBR, 0); + at91_sys_write(AT91_PMC_SCER, AT91_PMC_MCKUDP); + + /* + * MCK and CPU derive from one of those primary clocks. + * For now, assume this parentage won't change. + */ + mckr = at91_sys_read(AT91_PMC_MCKR); + mck.parent = clock_list[mckr & AT91_PMC_CSS]; + mck.parent->users++; + freq = mck.parent->rate_hz; + freq /= (1 << ((mckr >> 2) & 3)); /* prescale */ + mck.rate_hz = freq / (1 + ((mckr >> 8) & 3)); /* mdiv */ + + printk("Clocks: CPU %u MHz, master %u MHz, main %u.%03u MHz\n", + freq / 1000000, (unsigned) mck.rate_hz / 1000000, + (unsigned) main_clock / 1000000, + ((unsigned) main_clock % 1000000) / 1000); + + /* FIXME get rid of master_clock global */ + at91_master_clock = mck.rate_hz; + +#ifdef CONFIG_AT91_PROGRAMMABLE_CLOCKS + /* establish PCK0..PCK3 parentage */ + for (tmp = 0; tmp < ARRAY_SIZE(clock_list); tmp++) { + struct clk *clk = clock_list[tmp], *parent; + u32 pckr; + + if (!clk->programmable) + continue; + + pckr = at91_sys_read(AT91_PMC_PCKR(clk->id)); + parent = clock_list[pckr & 3]; + clk->parent = parent; + clk->rate_hz = parent->rate_hz / (1 << ((pckr >> 2) & 3)); + } +#else + /* disable unused clocks */ + at91_sys_write(AT91_PMC_SCDR, AT91_PMC_PCK0 | AT91_PMC_PCK1 | AT91_PMC_PCK2 | AT91_PMC_PCK3); +#endif /* CONFIG_AT91_PROGRAMMABLE_CLOCKS */ + + /* FIXME several unused clocks may still be active... provide + * a CONFIG option to turn off all unused clocks at some point + * before driver init starts. + */ + + return 0; +} diff --git a/arch/arm/mach-at91rm9200/common.c b/arch/arm/mach-at91rm9200/common.c new file mode 100644 index 000000000000..3848fd2d5596 --- /dev/null +++ b/arch/arm/mach-at91rm9200/common.c @@ -0,0 +1,115 @@ +/* + * arch/arm/mach-at91rm9200/common.c + * + * Copyright (C) 2005 SAN People + * + * This program is free software; you can redistribute it and/or modify + * it under the terms of the GNU General Public License as published by + * the Free Software Foundation; either version 2 of the License, or + * (at your option) any later version. + * + */ + +#include <linux/config.h> +#include <linux/module.h> + +#include <asm/mach/arch.h> +#include <asm/mach/map.h> + +#include <asm/arch/hardware.h> + +static struct map_desc at91rm9200_io_desc[] __initdata = { + { + .virtual = AT91_VA_BASE_SYS, + .pfn = __phys_to_pfn(AT91_BASE_SYS), + .length = SZ_4K, + .type = MT_DEVICE, + }, { + .virtual = AT91_VA_BASE_SPI, + .pfn = __phys_to_pfn(AT91_BASE_SPI), + .length = SZ_16K, + .type = MT_DEVICE, + }, { + .virtual = AT91_VA_BASE_SSC2, + .pfn = __phys_to_pfn(AT91_BASE_SSC2), + .length = SZ_16K, + .type = MT_DEVICE, + }, { + .virtual = AT91_VA_BASE_SSC1, + .pfn = __phys_to_pfn(AT91_BASE_SSC1), + .length = SZ_16K, + .type = MT_DEVICE, + }, { + .virtual = AT91_VA_BASE_SSC0, + .pfn = __phys_to_pfn(AT91_BASE_SSC0), + .length = SZ_16K, + .type = MT_DEVICE, + }, { + .virtual = AT91_VA_BASE_US3, + .pfn = __phys_to_pfn(AT91_BASE_US3), + .length = SZ_16K, + .type = MT_DEVICE, + }, { + .virtual = AT91_VA_BASE_US2, + .pfn = __phys_to_pfn(AT91_BASE_US2), + .length = SZ_16K, + .type = MT_DEVICE, + }, { + .virtual = AT91_VA_BASE_US1, + .pfn = __phys_to_pfn(AT91_BASE_US1), + .length = SZ_16K, + .type = MT_DEVICE, + }, { + .virtual = AT91_VA_BASE_US0, + .pfn = __phys_to_pfn(AT91_BASE_US0), + .length = SZ_16K, + .type = MT_DEVICE, + }, { + .virtual = AT91_VA_BASE_EMAC, + .pfn = __phys_to_pfn(AT91_BASE_EMAC), + .length = SZ_16K, + .type = MT_DEVICE, + }, { + .virtual = AT91_VA_BASE_TWI, + .pfn = __phys_to_pfn(AT91_BASE_TWI), + .length = SZ_16K, + .type = MT_DEVICE, + }, { + .virtual = AT91_VA_BASE_MCI, + .pfn = __phys_to_pfn(AT91_BASE_MCI), + .length = SZ_16K, + .type = MT_DEVICE, + }, { + .virtual = AT91_VA_BASE_UDP, + .pfn = __phys_to_pfn(AT91_BASE_UDP), + .length = SZ_16K, + .type = MT_DEVICE, + }, { + .virtual = AT91_VA_BASE_TCB1, + .pfn = __phys_to_pfn(AT91_BASE_TCB1), + .length = SZ_16K, + .type = MT_DEVICE, + }, { + .virtual = AT91_VA_BASE_TCB0, + .pfn = __phys_to_pfn(AT91_BASE_TCB0), + .length = SZ_16K, + .type = MT_DEVICE, + }, +}; + +void __init at91rm9200_map_io(void) +{ + iotable_init(at91rm9200_io_desc, ARRAY_SIZE(at91rm9200_io_desc)); +} + + +unsigned long at91_master_clock; + +EXPORT_SYMBOL(at91_master_clock); + + +int at91_serial_map[AT91_NR_UART]; +int at91_console_port; + +EXPORT_SYMBOL(at91_serial_map); +EXPORT_SYMBOL(at91_console_port); diff --git a/arch/arm/mach-at91rm9200/devices.c b/arch/arm/mach-at91rm9200/devices.c new file mode 100644 index 000000000000..8df3e5245651 --- /dev/null +++ b/arch/arm/mach-at91rm9200/devices.c @@ -0,0 +1,291 @@ +/* + * arch/arm/mach-at91rm9200/devices.c + * + * Copyright (C) 2005 Thibaut VARENE <varenet@parisc-linux.org> + * Copyright (C) 2005 David Brownell + * + * This program is free software; you can redistribute it and/or modify + * it under the terms of the GNU General Public License as published by + * the Free Software Foundation; either version 2 of the License, or + * (at your option) any later version. + * + */ +#include <asm/mach/arch.h> +#include <asm/mach/map.h> + +#include <linux/config.h> +#include <linux/platform_device.h> + +#include <asm/arch/board.h> +#include <asm/arch/pio.h> + + +/* -------------------------------------------------------------------- + * USB Host + * -------------------------------------------------------------------- */ + +#if defined(CONFIG_USB_OHCI_HCD) || defined(CONFIG_USB_OHCI_HCD_MODULE) +static u64 ohci_dmamask = 0xffffffffUL; +static struct at91_usbh_data usbh_data; + +static struct resource at91rm9200_usbh_resource[] = { + [0] = { + .start = AT91_UHP_BASE, + .end = AT91_UHP_BASE + SZ_1M -1, + .flags = IORESOURCE_MEM, + }, + [1] = { + .start = AT91_ID_UHP, + .end = AT91_ID_UHP, + .flags = IORESOURCE_IRQ, + }, +}; + +static struct platform_device at91rm9200_usbh_device = { + .name = "at91rm9200-ohci", + .id = -1, + .dev = { + .dma_mask = &ohci_dmamask, + .coherent_dma_mask = 0xffffffff, + .platform_data = &usbh_data, + }, + .resource = at91rm9200_usbh_resource, + .num_resources = ARRAY_SIZE(at91rm9200_usbh_resource), +}; + +void __init at91_add_device_usbh(struct at91_usbh_data *data) +{ + if (!data) + return; + + usbh_data = *data; + platform_device_register(&at91rm9200_usbh_device); +} +#else +void __init at91_add_device_usbh(struct at91_usbh_data *data) {} +#endif + + +/* -------------------------------------------------------------------- + * USB Device (Gadget) + * -------------------------------------------------------------------- */ + +#ifdef CONFIG_USB_GADGET_AT91 +static struct at91_udc_data udc_data; + +static struct resource at91_udc_resources[] = { + { + .start = AT91_BASE_UDP, + .end = AT91_BASE_UDP + SZ_16K - 1, + .flags = IORESOURCE_MEM, + } +}; + +static struct platform_device at91rm9200_udc_device = { + .name = "at91_udc", + .id = -1, + .dev = { + .platform_data = &udc_data, + }, + .resource = at91_udc_resources, + .num_resources = ARRAY_SIZE(at91_udc_resources), +}; + +void __init at91_add_device_udc(struct at91_udc_data *data) +{ + if (!data) + return; + + if (data->vbus_pin) { + at91_set_gpio_input(data->vbus_pin, 0); + at91_set_deglitch(data->vbus_pin, 1); + } + if (data->pullup_pin) + at91_set_gpio_output(data->pullup_pin, 0); + + udc_data = *data; + platform_device_register(&at91rm9200_udc_device); +} +#else +void __init at91_add_device_udc(struct at91_udc_data *data) {} +#endif + + +/* -------------------------------------------------------------------- + * Ethernet + * -------------------------------------------------------------------- */ + +#if defined(CONFIG_ARM_AT91_ETHER) || defined(CONFIG_ARM_AT91_ETHER_MODULE) +static u64 eth_dmamask = 0xffffffffUL; +static struct at91_eth_data eth_data; + +static struct platform_device at91rm9200_eth_device = { + .name = "at91_ether", + .id = -1, + .dev = { + .dma_mask = ð_dmamask, + .coherent_dma_mask = 0xffffffff, + .platform_data = ð_data, + }, + .num_resources = 0, +}; + +void __init at91_add_device_eth(struct at91_eth_data *data) +{ + if (!data) + return; + + if (data->phy_irq_pin) { + at91_set_gpio_input(data->phy_irq_pin, 0); + at91_set_deglitch(data->phy_irq_pin, 1); + } + + /* Pins used for MII and RMII */ + at91_set_A_periph(AT91_PIN_PA16, 0); /* EMDIO */ + at91_set_A_periph(AT91_PIN_PA15, 0); /* EMDC */ + at91_set_A_periph(AT91_PIN_PA14, 0); /* ERXER */ + at91_set_A_periph(AT91_PIN_PA13, 0); /* ERX1 */ + at91_set_A_periph(AT91_PIN_PA12, 0); /* ERX0 */ + at91_set_A_periph(AT91_PIN_PA11, 0); /* ECRS_ECRSDV */ + at91_set_A_periph(AT91_PIN_PA10, 0); /* ETX1 */ + at91_set_A_periph(AT91_PIN_PA9, 0); /* ETX0 */ + at91_set_A_periph(AT91_PIN_PA8, 0); /* ETXEN */ + at91_set_A_periph(AT91_PIN_PA7, 0); /* ETXCK_EREFCK */ + + if (!data->is_rmii) { + at91_set_B_periph(AT91_PIN_PB19, 0); /* ERXCK */ + at91_set_B_periph(AT91_PIN_PB18, 0); /* ECOL */ + at91_set_B_periph(AT91_PIN_PB17, 0); /* ERXDV */ + at91_set_B_periph(AT91_PIN_PB16, 0); /* ERX3 */ + at91_set_B_periph(AT91_PIN_PB15, 0); /* ERX2 */ + at91_set_B_periph(AT91_PIN_PB14, 0); /* ETXER */ + at91_set_B_periph(AT91_PIN_PB13, 0); /* ETX3 */ + at91_set_B_periph(AT91_PIN_PB12, 0); /* ETX2 */ + } + + eth_data = *data; + platform_device_register(&at91rm9200_eth_device); +} +#else +void __init at91_add_device_eth(struct at91_eth_data *data) {} +#endif + + +/* -------------------------------------------------------------------- + * Compact Flash / PCMCIA + * -------------------------------------------------------------------- */ + +#if defined(CONFIG_AT91_CF) || defined(CONFIG_AT91_CF_MODULE) +static struct at91_cf_data cf_data; + +static struct platform_device at91rm9200_cf_device = { + .name = "at91_cf", + .id = -1, + .dev = { + .platform_data = &cf_data, + }, + .num_resources = 0, +}; + +void __init at91_add_device_cf(struct at91_cf_data *data) +{ + if (!data) + return; + + /* input/irq */ + if (data->irq_pin) { + at91_set_gpio_input(data->irq_pin, 1); + at91_set_deglitch(data->irq_pin, 1); + } + at91_set_gpio_input(data->det_pin, 1); + at91_set_deglitch(data->det_pin, 1); + + /* outputs, initially off */ + if (data->vcc_pin) + at91_set_gpio_output(data->vcc_pin, 0); + at91_set_gpio_output(data->rst_pin, 0); + + cf_data = *data; + platform_device_register(&at91rm9200_cf_device); +} +#else +void __init at91_add_device_cf(struct at91_cf_data *data) {} +#endif + + +/* -------------------------------------------------------------------- + * MMC / SD + * -------------------------------------------------------------------- */ + +#if defined(CONFIG_MMC_AT91RM9200) || defined(CONFIG_MMC_AT91RM9200_MODULE) +static u64 mmc_dmamask = 0xffffffffUL; +static struct at91_mmc_data mmc_data; + +static struct resource at91_mmc_resources[] = { + { + .start = AT91_BASE_MCI, + .end = AT91_BASE_MCI + SZ_16K - 1, + .flags = IORESOURCE_MEM, + } +}; + +static struct platform_device at91rm9200_mmc_device = { + .name = "at91rm9200_mci", + .id = -1, + .dev = { + .dma_mask = &mmc_dmamask, + .coherent_dma_mask = 0xffffffff, + .platform_data = &mmc_data, + }, + .resource = at91_mmc_resources, + .num_resources = ARRAY_SIZE(at91_mmc_resources), +}; + +void __init at91_add_device_mmc(struct at91_mmc_data *data) +{ + if (!data) + return; + + /* input/irq */ + if (data->det_pin) { + at91_set_gpio_input(data->det_pin, 1); + at91_set_deglitch(data->det_pin, 1); + } + if (data->wp_pin) + at91_set_gpio_input(data->wp_pin, 1); + + /* CLK */ + at91_set_A_periph(AT91_PIN_PA27, 0); + + if (data->is_b) { + /* CMD */ + at91_set_B_periph(AT91_PIN_PA8, 0); + + /* DAT0, maybe DAT1..DAT3 */ + at91_set_B_periph(AT91_PIN_PA9, 0); + if (data->wire4) { + at91_set_B_periph(AT91_PIN_PA10, 0); + at91_set_B_periph(AT91_PIN_PA11, 0); + at91_set_B_periph(AT91_PIN_PA12, 0); + } + } else { + /* CMD */ + at91_set_A_periph(AT91_PIN_PA28, 0); + + /* DAT0, maybe DAT1..DAT3 */ + at91_set_A_periph(AT91_PIN_PA29, 0); + if (data->wire4) { + at91_set_B_periph(AT91_PIN_PB3, 0); + at91_set_B_periph(AT91_PIN_PB4, 0); + at91_set_B_periph(AT91_PIN_PB5, 0); + } + } + + mmc_data = *data; + platform_device_register(&at91rm9200_mmc_device); +} +#else +void __init at91_add_device_mmc(struct at91_mmc_data *data) {} +#endif + +/* -------------------------------------------------------------------- */ diff --git a/arch/arm/mach-at91rm9200/generic.h b/arch/arm/mach-at91rm9200/generic.h new file mode 100644 index 000000000000..9bd541eba0a0 --- /dev/null +++ b/arch/arm/mach-at91rm9200/generic.h @@ -0,0 +1,18 @@ +/* + * linux/arch/arm/mach-at91rm9200/generic.h + * + * Copyright (C) 2005 David Brownell + * + * This program is free software; you can redistribute it and/or modify + * it under the terms of the GNU General Public License version 2 as + * published by the Free Software Foundation. + */ + +void at91_gpio_irq_setup(unsigned banks); + +struct sys_timer; +extern struct sys_timer at91rm9200_timer; + +extern void __init at91rm9200_map_io(void); + +extern int __init at91_clock_init(unsigned long main_clock); diff --git a/arch/arm/mach-at91rm9200/gpio.c b/arch/arm/mach-at91rm9200/gpio.c new file mode 100644 index 000000000000..2fd2ef583e4d --- /dev/null +++ b/arch/arm/mach-at91rm9200/gpio.c @@ -0,0 +1,302 @@ +/* + * linux/arch/arm/mach-at91rm9200/gpio.c + * + * Copyright (C) 2005 HP Labs + * + * This program is free software; you can redistribute it and/or modify + * it under the terms of the GNU General Public License as published by + * the Free Software Foundation; either version 2 of the License, or + * (at your option) any later version. + */ + +#include <linux/errno.h> +#include <linux/kernel.h> +#include <linux/list.h> +#include <linux/module.h> + +#include <asm/io.h> +#include <asm/mach/irq.h> +#include <asm/arch/hardware.h> +#include <asm/arch/gpio.h> + +static const u32 pio_controller_offset[4] = { + AT91_PIOA, + AT91_PIOB, + AT91_PIOC, + AT91_PIOD, +}; + +static inline void __iomem *pin_to_controller(unsigned pin) +{ + void __iomem *sys_base = (void __iomem *) AT91_VA_BASE_SYS; + + pin -= PIN_BASE; + pin /= 32; + if (likely(pin < BGA_GPIO_BANKS)) + return sys_base + pio_controller_offset[pin]; + + return NULL; +} + +static inline unsigned pin_to_mask(unsigned pin) +{ + pin -= PIN_BASE; + return 1 << (pin % 32); +} + + +/*--------------------------------------------------------------------------*/ + +/* Not all hardware capabilities are exposed through these calls; they + * only encapsulate the most common features and modes. (So if you + * want to change signals in groups, do it directly.) + * + * Bootloaders will usually handle some of the pin multiplexing setup. + * The intent is certainly that by the time Linux is fully booted, all + * pins should have been fully initialized. These setup calls should + * only be used by board setup routines, or possibly in driver probe(). + * + * For bootloaders doing all that setup, these calls could be inlined + * as NOPs so Linux won't duplicate any setup code + */ + + +/* + * mux the pin to the "A" internal peripheral role. + */ +int __init_or_module at91_set_A_periph(unsigned pin, int use_pullup) +{ + void __iomem *pio = pin_to_controller(pin); + unsigned mask = pin_to_mask(pin); + + if (!pio) + return -EINVAL; + + __raw_writel(mask, pio + PIO_IDR); + __raw_writel(mask, pio + (use_pullup ? PIO_PUER : PIO_PUDR)); + __raw_writel(mask, pio + PIO_ASR); + __raw_writel(mask, pio + PIO_PDR); + return 0; +} +EXPORT_SYMBOL(at91_set_A_periph); + + +/* + * mux the pin to the "B" internal peripheral role. + */ +int __init_or_module at91_set_B_periph(unsigned pin, int use_pullup) +{ + void __iomem *pio = pin_to_controller(pin); + unsigned mask = pin_to_mask(pin); + + if (!pio) + return -EINVAL; + + __raw_writel(mask, pio + PIO_IDR); + __raw_writel(mask, pio + (use_pullup ? PIO_PUER : PIO_PUDR)); + __raw_writel(mask, pio + PIO_BSR); + __raw_writel(mask, pio + PIO_PDR); + return 0; +} +EXPORT_SYMBOL(at91_set_B_periph); + + +/* + * mux the pin to the gpio controller (instead of "A" or "B" peripheral), and + * configure it for an input. + */ +int __init_or_module at91_set_gpio_input(unsigned pin, int use_pullup) +{ + void __iomem *pio = pin_to_controller(pin); + unsigned mask = pin_to_mask(pin); + + if (!pio) + return -EINVAL; + + __raw_writel(mask, pio + PIO_IDR); + __raw_writel(mask, pio + (use_pullup ? PIO_PUER : PIO_PUDR)); + __raw_writel(mask, pio + PIO_ODR); + __raw_writel(mask, pio + PIO_PER); + return 0; +} +EXPORT_SYMBOL(at91_set_gpio_input); + + +/* + * mux the pin to the gpio controller (instead of "A" or "B" peripheral), + * and configure it for an output. + */ +int __init_or_module at91_set_gpio_output(unsigned pin, int value) +{ + void __iomem *pio = pin_to_controller(pin); + unsigned mask = pin_to_mask(pin); + + if (!pio) + return -EINVAL; + + __raw_writel(mask, pio + PIO_IDR); + __raw_writel(mask, pio + PIO_PUDR); + __raw_writel(mask, pio + (value ? PIO_SODR : PIO_CODR)); + __raw_writel(mask, pio + PIO_OER); + __raw_writel(mask, pio + PIO_PER); + return 0; +} +EXPORT_SYMBOL(at91_set_gpio_output); + + +/* + * enable/disable the glitch filter; mostly used with IRQ handling. + */ +int __init_or_module at91_set_deglitch(unsigned pin, int is_on) +{ + void __iomem *pio = pin_to_controller(pin); + unsigned mask = pin_to_mask(pin); + + if (!pio) + return -EINVAL; + __raw_writel(mask, pio + (is_on ? PIO_IFER : PIO_IFDR)); + return 0; +} +EXPORT_SYMBOL(at91_set_deglitch); + +/*--------------------------------------------------------------------------*/ + + +/* + * assuming the pin is muxed as a gpio output, set its value. + */ +int at91_set_gpio_value(unsigned pin, int value) +{ + void __iomem *pio = pin_to_controller(pin); + unsigned mask = pin_to_mask(pin); + + if (!pio) + return -EINVAL; + __raw_writel(mask, pio + (value ? PIO_SODR : PIO_CODR)); + return 0; +} +EXPORT_SYMBOL(at91_set_gpio_value); + + +/* + * read the pin's value (works even if it's not muxed as a gpio). + */ +int at91_get_gpio_value(unsigned pin) +{ + void __iomem *pio = pin_to_controller(pin); + unsigned mask = pin_to_mask(pin); + u32 pdsr; + + if (!pio) + return -EINVAL; + pdsr = __raw_readl(pio + PIO_PDSR); + return (pdsr & mask) != 0; +} +EXPORT_SYMBOL(at91_get_gpio_value); + +/*--------------------------------------------------------------------------*/ + + +/* Several AIC controller irqs are dispatched through this GPIO handler. + * To use any AT91_PIN_* as an externally triggered IRQ, first call + * at91_set_gpio_input() then maybe enable its glitch filter. + * Then just request_irq() with the pin ID; it works like any ARM IRQ + * handler, though it always triggers on rising and falling edges. + * + * Alternatively, certain pins may be used directly as IRQ0..IRQ6 after + * configuring them with at91_set_a_periph() or at91_set_b_periph(). + * IRQ0..IRQ6 should be configurable, e.g. level vs edge triggering. + */ + +static void gpio_irq_mask(unsigned pin) +{ + void __iomem *pio = pin_to_controller(pin); + unsigned mask = pin_to_mask(pin); + + if (pio) + __raw_writel(mask, pio + PIO_IDR); +} + +static void gpio_irq_unmask(unsigned pin) +{ + void __iomem *pio = pin_to_controller(pin); + unsigned mask = pin_to_mask(pin); + + if (pio) + __raw_writel(mask, pio + PIO_IER); +} + +static int gpio_irq_type(unsigned pin, unsigned type) +{ + return (type == IRQT_BOTHEDGE) ? 0 : -EINVAL; +} + +static struct irqchip gpio_irqchip = { + .mask = gpio_irq_mask, + .unmask = gpio_irq_unmask, + .set_type = gpio_irq_type, +}; + +static void gpio_irq_handler(unsigned irq, struct irqdesc *desc, struct pt_regs *regs) +{ + unsigned pin; + struct irqdesc *gpio; + void __iomem *pio; + u32 isr; + + pio = (void __force __iomem *) desc->chipdata; + + /* temporarily mask (level sensitive) parent IRQ */ + desc->chip->ack(irq); + for (;;) { + isr = __raw_readl(pio + PIO_ISR) & __raw_readl(pio + PIO_IMR); + if (!isr) + break; + + pin = (unsigned) desc->data; + gpio = &irq_desc[pin]; + + while (isr) { + if (isr & 1) + gpio->handle(pin, gpio, regs); + pin++; + gpio++; + isr >>= 1; + } + } + desc->chip->unmask(irq); + /* now it may re-trigger */ +} + +/* call this from board-specific init_irq */ +void __init at91_gpio_irq_setup(unsigned banks) +{ + unsigned pioc, pin, id; + + if (banks > 4) + banks = 4; + for (pioc = 0, pin = PIN_BASE, id = AT91_ID_PIOA; + pioc < banks; + pioc++, id++) { + void __iomem *controller; + unsigned i; + + controller = (void __iomem *) AT91_VA_BASE_SYS + pio_controller_offset[pioc]; + __raw_writel(~0, controller + PIO_IDR); + + set_irq_data(id, (void *) pin); + set_irq_chipdata(id, (void __force *) controller); + + for (i = 0; i < 32; i++, pin++) { + set_irq_chip(pin, &gpio_irqchip); + set_irq_handler(pin, do_simple_IRQ); + set_irq_flags(pin, IRQF_VALID); + } + + set_irq_chained_handler(id, gpio_irq_handler); + + /* enable the PIO peripheral clock */ + at91_sys_write(AT91_PMC_PCER, 1 << id); + } + pr_info("AT91: %d gpio irqs in %d banks\n", pin - PIN_BASE, banks); +} diff --git a/arch/arm/mach-at91rm9200/irq.c b/arch/arm/mach-at91rm9200/irq.c new file mode 100644 index 000000000000..cb62bc83a1dd --- /dev/null +++ b/arch/arm/mach-at91rm9200/irq.c @@ -0,0 +1,170 @@ +/* + * linux/arch/arm/mach-at91rm9200/irq.c + * + * Copyright (C) 2004 SAN People + * Copyright (C) 2004 ATMEL + * Copyright (C) Rick Bronson + * + * This program is free software; you can redistribute it and/or modify + * it under the terms of the GNU General Public License as published by + * the Free Software Foundation; either version 2 of the License, or + * (at your option) any later version. + * + * This program is distributed in the hope that it will be useful, + * but WITHOUT ANY WARRANTY; without even the implied warranty of + * MERCHANTABILITY or FITNESS FOR A PARTICULAR PURPOSE. See the + * GNU General Public License for more details. + * + * You should have received a copy of the GNU General Public License + * along with this program; if not, write to the Free Software + * Foundation, Inc., 59 Temple Place, Suite 330, Boston, MA 02111-1307 USA + */ + +#include <linux/config.h> +#include <linux/init.h> +#include <linux/module.h> +#include <linux/mm.h> +#include <linux/types.h> + +#include <asm/hardware.h> +#include <asm/irq.h> +#include <asm/mach-types.h> +#include <asm/setup.h> + +#include <asm/mach/arch.h> +#include <asm/mach/irq.h> +#include <asm/mach/map.h> + +#include "generic.h" + +/* + * The default interrupt priority levels (0 = lowest, 7 = highest). + */ +static unsigned int at91rm9200_default_irq_priority[NR_AIC_IRQS] __initdata = { + 7, /* Advanced Interrupt Controller */ + 7, /* System Peripheral */ + 0, /* Parallel IO Controller A */ + 0, /* Parallel IO Controller B */ + 0, /* Parallel IO Controller C */ + 0, /* Parallel IO Controller D */ + 6, /* USART 0 */ + 6, /* USART 1 */ + 6, /* USART 2 */ + 6, /* USART 3 */ + 0, /* Multimedia Card Interface */ + 4, /* USB Device Port */ + 0, /* Two-Wire Interface */ + 6, /* Serial Peripheral Interface */ + 5, /* Serial Synchronous Controller */ + 5, /* Serial Synchronous Controller */ + 5, /* Serial Synchronous Controller */ + 0, /* Timer Counter 0 */ + 0, /* Timer Counter 1 */ + 0, /* Timer Counter 2 */ + 0, /* Timer Counter 3 */ + 0, /* Timer Counter 4 */ + 0, /* Timer Counter 5 */ + 3, /* USB Host port */ + 3, /* Ethernet MAC */ + 0, /* Advanced Interrupt Controller */ + 0, /* Advanced Interrupt Controller */ + 0, /* Advanced Interrupt Controller */ + 0, /* Advanced Interrupt Controller */ + 0, /* Advanced Interrupt Controller */ + 0, /* Advanced Interrupt Controller */ + 0 /* Advanced Interrupt Controller */ +}; + + +static void at91rm9200_mask_irq(unsigned int irq) +{ + /* Disable interrupt on AIC */ + at91_sys_write(AT91_AIC_IDCR, 1 << irq); +} + +static void at91rm9200_unmask_irq(unsigned int irq) +{ + /* Enable interrupt on AIC */ + at91_sys_write(AT91_AIC_IECR, 1 << irq); +} + +static int at91rm9200_irq_type(unsigned irq, unsigned type) +{ + unsigned int smr, srctype; + + /* change triggering only for FIQ and external IRQ0..IRQ6 */ + if ((irq < AT91_ID_IRQ0) && (irq != AT91_ID_FIQ)) + return -EINVAL; + + switch (type) { + case IRQT_HIGH: + srctype = AT91_AIC_SRCTYPE_HIGH; + break; + case IRQT_RISING: + srctype = AT91_AIC_SRCTYPE_RISING; + break; + case IRQT_LOW: + srctype = AT91_AIC_SRCTYPE_LOW; + break; + case IRQT_FALLING: + srctype = AT91_AIC_SRCTYPE_FALLING; + break; + default: + return -EINVAL; + } + + smr = at91_sys_read(AT91_AIC_SMR(irq)) & ~AT91_AIC_SRCTYPE; + at91_sys_write(AT91_AIC_SMR(irq), smr | srctype); + return 0; +} + +static struct irqchip at91rm9200_irq_chip = { + .ack = at91rm9200_mask_irq, + .mask = at91rm9200_mask_irq, + .unmask = at91rm9200_unmask_irq, + .set_type = at91rm9200_irq_type, +}; + +/* + * Initialize the AIC interrupt controller. + */ +void __init at91rm9200_init_irq(unsigned int priority[NR_AIC_IRQS]) +{ + unsigned int i; + + /* No priority list specified for this board -> use defaults */ + if (priority == NULL) + priority = at91rm9200_default_irq_priority; + + /* + * The IVR is used by macro get_irqnr_and_base to read and verify. + * The irq number is NR_AIC_IRQS when a spurious interrupt has occurred. + */ + for (i = 0; i < NR_AIC_IRQS; i++) { + /* Put irq number in Source Vector Register: */ + at91_sys_write(AT91_AIC_SVR(i), i); + /* Store the Source Mode Register as defined in table above */ + at91_sys_write(AT91_AIC_SMR(i), AT91_AIC_SRCTYPE_LOW | priority[i]); + + set_irq_chip(i, &at91rm9200_irq_chip); + set_irq_handler(i, do_level_IRQ); + set_irq_flags(i, IRQF_VALID | IRQF_PROBE); + + /* Perform 8 End Of Interrupt Command to make sure AIC will not Lock out nIRQ */ + if (i < 8) + at91_sys_write(AT91_AIC_EOICR, 0); + } + + /* + * Spurious Interrupt ID in Spurious Vector Register is NR_AIC_IRQS + * When there is no current interrupt, the IRQ Vector Register reads the value stored in AIC_SPU + */ + at91_sys_write(AT91_AIC_SPU, NR_AIC_IRQS); + + /* No debugging in AIC: Debug (Protect) Control Register */ + at91_sys_write(AT91_AIC_DCR, 0); + + /* Disable and clear all interrupts initially */ + at91_sys_write(AT91_AIC_IDCR, 0xFFFFFFFF); + at91_sys_write(AT91_AIC_ICCR, 0xFFFFFFFF); +} diff --git a/arch/arm/mach-at91rm9200/time.c b/arch/arm/mach-at91rm9200/time.c new file mode 100644 index 000000000000..1b6dd2deeb22 --- /dev/null +++ b/arch/arm/mach-at91rm9200/time.c @@ -0,0 +1,127 @@ +/* + * linux/arch/arm/mach-at91rm9200/time.c + * + * Copyright (C) 2003 SAN People + * Copyright (C) 2003 ATMEL + * + * This program is free software; you can redistribute it and/or modify + * it under the terms of the GNU General Public License as published by + * the Free Software Foundation; either version 2 of the License, or + * (at your option) any later version. + * + * This program is distributed in the hope that it will be useful, + * but WITHOUT ANY WARRANTY; without even the implied warranty of + * MERCHANTABILITY or FITNESS FOR A PARTICULAR PURPOSE. See the + * GNU General Public License for more details. + * + * You should have received a copy of the GNU General Public License + * along with this program; if not, write to the Free Software + * Foundation, Inc., 59 Temple Place, Suite 330, Boston, MA 02111-1307 USA + */ + +#include <linux/config.h> +#include <linux/init.h> +#include <linux/interrupt.h> +#include <linux/kernel.h> +#include <linux/sched.h> +#include <linux/time.h> + +#include <asm/hardware.h> +#include <asm/io.h> +#include <asm/irq.h> +#include <asm/mach/time.h> + +/* + * The ST_CRTR is updated asynchronously to the master clock. It is therefore + * necessary to read it twice (with the same value) to ensure accuracy. + */ +static inline unsigned long read_CRTR(void) { + unsigned long x1, x2; + + do { + x1 = at91_sys_read(AT91_ST_CRTR); + x2 = at91_sys_read(AT91_ST_CRTR); + } while (x1 != x2); + + return x1; +} + +/* + * Returns number of microseconds since last timer interrupt. Note that interrupts + * will have been disabled by do_gettimeofday() + * 'LATCH' is hwclock ticks (see CLOCK_TICK_RATE in timex.h) per jiffy. + * 'tick' is usecs per jiffy (linux/timex.h). + */ +static unsigned long at91rm9200_gettimeoffset(void) +{ + unsigned long elapsed; + + elapsed = (read_CRTR() - at91_sys_read(AT91_ST_RTAR)) & AT91_ST_ALMV; + + return (unsigned long)(elapsed * (tick_nsec / 1000)) / LATCH; +} + +/* + * IRQ handler for the timer. + */ +static irqreturn_t at91rm9200_timer_interrupt(int irq, void *dev_id, struct pt_regs *regs) +{ + unsigned long rtar; + + if (at91_sys_read(AT91_ST_SR) & AT91_ST_PITS) { /* This is a shared interrupt */ + write_seqlock(&xtime_lock); + + do { + timer_tick(regs); + rtar = (at91_sys_read(AT91_ST_RTAR) + LATCH) & AT91_ST_ALMV; + at91_sys_write(AT91_ST_RTAR, rtar); + } while (((read_CRTR() - at91_sys_read(AT91_ST_RTAR)) & AT91_ST_ALMV) >= LATCH); + + write_sequnlock(&xtime_lock); + + return IRQ_HANDLED; + } + else + return IRQ_NONE; /* not handled */ +} + +static struct irqaction at91rm9200_timer_irq = { + .name = "at91_tick", + .flags = SA_SHIRQ | SA_INTERRUPT, + .handler = at91rm9200_timer_interrupt +}; + +/* + * Set up timer interrupt. + */ +void __init at91rm9200_timer_init(void) +{ + /* Disable all timer interrupts */ + at91_sys_write(AT91_ST_IDR, AT91_ST_PITS | AT91_ST_WDOVF | AT91_ST_RTTINC | AT91_ST_ALMS); + (void) at91_sys_read(AT91_ST_SR); /* Clear any pending interrupts */ + + /* + * Make IRQs happen for the system timer. + */ + setup_irq(AT91_ID_SYS, &at91rm9200_timer_irq); + + /* Set initial alarm to 0 */ + at91_sys_write(AT91_ST_RTAR, 0); + + /* Real time counter incremented every 30.51758 microseconds */ + at91_sys_write(AT91_ST_RTMR, 1); + + /* Set Period Interval timer */ + at91_sys_write(AT91_ST_PIMR, LATCH); + + /* Change the kernel's 'tick' value to 10009 usec. (the default is 10000) */ + tick_usec = (LATCH * 1000000) / CLOCK_TICK_RATE; + + /* Enable Period Interval Timer interrupt */ + at91_sys_write(AT91_ST_IER, AT91_ST_PITS); +} + +struct sys_timer at91rm9200_timer = { + .init = at91rm9200_timer_init, + .offset = at91rm9200_gettimeoffset, +}; diff --git a/arch/arm/mach-epxa10db/Kconfig b/arch/arm/mach-epxa10db/Kconfig deleted file mode 100644 index 55d896dd4950..000000000000 --- a/arch/arm/mach-epxa10db/Kconfig +++ /dev/null @@ -1,23 +0,0 @@ -if ARCH_CAMELOT - -menu "Epxa10db" - -comment "PLD hotswap support" - -config PLD - bool - default y - -config PLD_HOTSWAP - bool "Support for PLD device hotplugging (experimental)" - depends on EXPERIMENTAL - help - This enables support for the dynamic loading and configuration of - compatible drivers when the contents of the PLD are changed. This - is still experimental and requires configuration tools which are - not yet generally available. Say N here. You must enable the kernel - module loader for this feature to work. - -endmenu - -endif diff --git a/arch/arm/mach-epxa10db/Makefile b/arch/arm/mach-epxa10db/Makefile deleted file mode 100644 index 24fbd7d3a3c1..000000000000 --- a/arch/arm/mach-epxa10db/Makefile +++ /dev/null @@ -1,11 +0,0 @@ -# -# Makefile for the linux kernel. -# - -# Object file lists. - -obj-y := arch.o irq.o mm.o time.o -obj-m := -obj-n := -obj- := - diff --git a/arch/arm/mach-epxa10db/Makefile.boot b/arch/arm/mach-epxa10db/Makefile.boot deleted file mode 100644 index 28bec7d3fc88..000000000000 --- a/arch/arm/mach-epxa10db/Makefile.boot +++ /dev/null @@ -1,2 +0,0 @@ - zreladdr-y := 0x00008000 - diff --git a/arch/arm/mach-epxa10db/arch.c b/arch/arm/mach-epxa10db/arch.c deleted file mode 100644 index 44c56571d183..000000000000 --- a/arch/arm/mach-epxa10db/arch.c +++ /dev/null @@ -1,74 +0,0 @@ -/* - * linux/arch/arm/mach-epxa10db/arch.c - * - * Copyright (C) 2000 Deep Blue Solutions Ltd - * Copyright (C) 2001 Altera Corporation - * - * This program is free software; you can redistribute it and/or modify - * it under the terms of the GNU General Public License as published by - * the Free Software Foundation; either version 2 of the License, or - * (at your option) any later version. - * - * This program is distributed in the hope that it will be useful, - * but WITHOUT ANY WARRANTY; without even the implied warranty of - * MERCHANTABILITY or FITNESS FOR A PARTICULAR PURPOSE. See the - * GNU General Public License for more details. - * - * You should have received a copy of the GNU General Public License - * along with this program; if not, write to the Free Software - * Foundation, Inc., 59 Temple Place, Suite 330, Boston, MA 02111-1307 USA - */ -#include <linux/types.h> -#include <linux/init.h> -#include <linux/serial_8250.h> - -#include <asm/hardware.h> -#include <asm/setup.h> -#include <asm/mach-types.h> - -#include <asm/mach/arch.h> - -static struct plat_serial8250_port serial_platform_data[] = { - { - .iobase = 0x3f8, - .irq = IRQ_UARTINT0, -#error FIXME - .uartclk = 0, - .regshift = 0, - .iotype = UPIO_PORT, - .flags = UPF_BOOT_AUTOCONF | UPF_SKIP_TEST, - }, - { - .iobase = 0x2f8, - .irq = IRQ_UARTINT1, -#error FIXME - .uartclk = 0, - .regshift = 0, - .iotype = UPIO_PORT, - .flags = UPF_BOOT_AUTOCONF | UPF_SKIP_TEST, - }, - { }, -}; - -static struct platform_device serial_device = { - .name = "serial8250", - .id = PLAT8250_DEV_PLATFORM, - .dev = { - .platform_data = serial_platform_data, - }, -}; - -extern void epxa10db_map_io(void); -extern void epxa10db_init_irq(void); -extern struct sys_timer epxa10db_timer; - -MACHINE_START(CAMELOT, "Altera Epxa10db") - /* Maintainer: Altera Corporation */ - .phys_ram = 0x00000000, - .phys_io = 0x7fffc000, - .io_pg_offst = ((0xffffc000) >> 18) & 0xfffc, - .map_io = epxa10db_map_io, - .init_irq = epxa10db_init_irq, - .timer = &epxa10db_timer, -MACHINE_END - diff --git a/arch/arm/mach-epxa10db/irq.c b/arch/arm/mach-epxa10db/irq.c deleted file mode 100644 index 9bf927e13309..000000000000 --- a/arch/arm/mach-epxa10db/irq.c +++ /dev/null @@ -1,82 +0,0 @@ -/* - * linux/arch/arm/mach-epxa10db/irq.c - * - * Copyright (C) 2001 Altera Corporation - * - * This program is free software; you can redistribute it and/or modify - * it under the terms of the GNU General Public License as published by - * the Free Software Foundation; either version 2 of the License, or - * (at your option) any later version. - * - * This program is distributed in the hope that it will be useful, - * but WITHOUT ANY WARRANTY; without even the implied warranty of - * MERCHANTABILITY or FITNESS FOR A PARTICULAR PURPOSE. See the - * GNU General Public License for more details. - * - * You should have received a copy of the GNU General Public License - * along with this program; if not, write to the Free Software - * Foundation, Inc., 59 Temple Place, Suite 330, Boston, MA 02111-1307 USA - */ -#include <linux/init.h> -#include <linux/ioport.h> -#include <linux/stddef.h> -#include <linux/timer.h> -#include <linux/list.h> -#include <asm/io.h> -#include <asm/hardware.h> -#include <asm/irq.h> -#include <asm/mach/irq.h> -#include <asm/arch/platform.h> -#include <asm/arch/int_ctrl00.h> - - -static void epxa_mask_irq(unsigned int irq) -{ - writel(1 << irq, INT_MC(IO_ADDRESS(EXC_INT_CTRL00_BASE))); -} - -static void epxa_unmask_irq(unsigned int irq) -{ - writel(1 << irq, INT_MS(IO_ADDRESS(EXC_INT_CTRL00_BASE))); -} - - -static struct irqchip epxa_irq_chip = { - .ack = epxa_mask_irq, - .mask = epxa_mask_irq, - .unmask = epxa_unmask_irq, -}; - -static struct resource irq_resource = { - .name = "irq_handler", - .start = IO_ADDRESS(EXC_INT_CTRL00_BASE), - .end = IO_ADDRESS(INT_PRIORITY_FC(EXC_INT_CTRL00_BASE))+4, -}; - -void __init epxa10db_init_irq(void) -{ - unsigned int i; - - request_resource(&iomem_resource, &irq_resource); - - /* - * This bit sets up the interrupt controller using - * the 6 PLD interrupts mode (the default) each - * irqs is assigned a priority which is the same - * as its interrupt number. This scheme is used because - * its easy, but you may want to change it depending - * on the contents of your PLD - */ - - writel(3,INT_MODE(IO_ADDRESS(EXC_INT_CTRL00_BASE))); - for (i = 0; i < NR_IRQS; i++){ - writel(i+1, INT_PRIORITY_P0(IO_ADDRESS(EXC_INT_CTRL00_BASE)) + (4*i)); - set_irq_chip(i,&epxa_irq_chip); - set_irq_handler(i,do_level_IRQ); - set_irq_flags(i, IRQF_VALID | IRQF_PROBE); - } - - /* Disable all interrupts */ - writel(-1,INT_MC(IO_ADDRESS(EXC_INT_CTRL00_BASE))); - -} diff --git a/arch/arm/mach-epxa10db/mm.c b/arch/arm/mach-epxa10db/mm.c deleted file mode 100644 index cfd0d2182d44..000000000000 --- a/arch/arm/mach-epxa10db/mm.c +++ /dev/null @@ -1,71 +0,0 @@ -/* - * linux/arch/arm/mach-epxa10db/mm.c - * - * MM routines for Altera'a Epxa10db board - * - * Copyright (C) 2001 Altera Corporation - * - * This program is free software; you can redistribute it and/or modify - * it under the terms of the GNU General Public License as published by - * the Free Software Foundation; either version 2 of the License, or - * (at your option) any later version. - * - * This program is distributed in the hope that it will be useful, - * but WITHOUT ANY WARRANTY; without even the implied warranty of - * MERCHANTABILITY or FITNESS FOR A PARTICULAR PURPOSE. See the - * GNU General Public License for more details. - * - * You should have received a copy of the GNU General Public License - * along with this program; if not, write to the Free Software - * Foundation, Inc., 59 Temple Place, Suite 330, Boston, MA 02111-1307 USA - */ -#include <linux/kernel.h> -#include <linux/init.h> - -#include <asm/hardware.h> -#include <asm/io.h> -#include <asm/sizes.h> -#include <asm/page.h> - -#include <asm/mach/map.h> - -/* Page table mapping for I/O region */ - -static struct map_desc epxa10db_io_desc[] __initdata = { - { - .virtual = IO_ADDRESS(EXC_REGISTERS_BASE), - .pfn = __phys_to_pfn(EXC_REGISTERS_BASE), - .length = SZ_16K, - .type = MT_DEVICE - }, { - .virtual = IO_ADDRESS(EXC_PLD_BLOCK0_BASE), - .pfn = __phys_to_pfn(EXC_PLD_BLOCK0_BASE), - .length = SZ_16K, - .type = MT_DEVICE - }, { - .virtual = IO_ADDRESS(EXC_PLD_BLOCK1_BASE), - .pfn =__phys_to_pfn(EXC_PLD_BLOCK1_BASE), - .length = SZ_16K, - .type = MT_DEVICE - }, { - .virtual = IO_ADDRESS(EXC_PLD_BLOCK2_BASE), - .physical = __phys_to_pfn(EXC_PLD_BLOCK2_BASE), - .length = SZ_16K, - .type = MT_DEVICE - }, { - .virtual = IO_ADDRESS(EXC_PLD_BLOCK3_BASE), - .pfn = __phys_to_pfn(EXC_PLD_BLOCK3_BASE), - .length = SZ_16K, - .type = MT_DEVICE - }, { - .virtual = FLASH_VADDR(EXC_EBI_BLOCK0_BASE), - .pfn = __phys_to_pfn(EXC_EBI_BLOCK0_BASE), - .length = SZ_16M, - .type = MT_DEVICE - } -}; - -void __init epxa10db_map_io(void) -{ - iotable_init(epxa10db_io_desc, ARRAY_SIZE(epxa10db_io_desc)); -} diff --git a/arch/arm/mach-epxa10db/time.c b/arch/arm/mach-epxa10db/time.c deleted file mode 100644 index 4b1084dde8dd..000000000000 --- a/arch/arm/mach-epxa10db/time.c +++ /dev/null @@ -1,78 +0,0 @@ -/* - * linux/arch/arm/mach-epxa10db/time.c - * - * Copyright (C) 2000 Deep Blue Solutions - * Copyright (C) 2001 Altera Corporation - * - * This program is free software; you can redistribute it and/or modify - * it under the terms of the GNU General Public License version 2 as - * published by the Free Software Foundation. - */ -#include <linux/kernel.h> -#include <linux/init.h> -#include <linux/interrupt.h> -#include <linux/sched.h> - -#include <asm/hardware.h> -#include <asm/system.h> -#include <asm/leds.h> - -#include <asm/mach/time.h> - -#define TIMER00_TYPE (volatile unsigned int*) -#include <asm/arch/timer00.h> - -static int epxa10db_set_rtc(void) -{ - return 1; -} - -static int epxa10db_rtc_init(void) -{ - set_rtc = epxa10db_set_rtc; - - return 0; -} - -__initcall(epxa10db_rtc_init); - - -/* - * IRQ handler for the timer - */ -static irqreturn_t -epxa10db_timer_interrupt(int irq, void *dev_id, struct pt_regs *regs) -{ - write_seqlock(&xtime_lock); - - // ...clear the interrupt - *TIMER0_CR(IO_ADDRESS(EXC_TIMER00_BASE))|=TIMER0_CR_CI_MSK; - - timer_tick(regs); - write_sequnlock(&xtime_lock); - - return IRQ_HANDLED; -} - -static struct irqaction epxa10db_timer_irq = { - .name = "Excalibur Timer Tick", - .flags = SA_INTERRUPT | SA_TIMER, - .handler = epxa10db_timer_interrupt, -}; - -/* - * Set up timer interrupt, and return the current time in seconds. - */ -static void __init epxa10db_timer_init(void) -{ - /* Start the timer */ - *TIMER0_LIMIT(IO_ADDRESS(EXC_TIMER00_BASE))=(unsigned int)(EXC_AHB2_CLK_FREQUENCY/200); - *TIMER0_PRESCALE(IO_ADDRESS(EXC_TIMER00_BASE))=1; - *TIMER0_CR(IO_ADDRESS(EXC_TIMER00_BASE))=TIMER0_CR_IE_MSK | TIMER0_CR_S_MSK; - - setup_irq(IRQ_TIMER0, &epxa10db_timer_irq); -} - -struct sys_timer epxa10db_timer = { - .init = epxa10db_timer_init, -}; diff --git a/arch/arm/mach-s3c2410/clock.c b/arch/arm/mach-s3c2410/clock.c index 5830ae3ddd19..fc09ba92d66a 100644 --- a/arch/arm/mach-s3c2410/clock.c +++ b/arch/arm/mach-s3c2410/clock.c @@ -253,100 +253,101 @@ struct clk s3c24xx_uclk = { /* clock definitions */ static struct clk init_clocks[] = { - { .name = "nand", - .id = -1, - .parent = &clk_h, - .enable = s3c24xx_clkcon_enable, - .ctrlbit = S3C2410_CLKCON_NAND - }, - { .name = "lcd", - .id = -1, - .parent = &clk_h, - .enable = s3c24xx_clkcon_enable, - .ctrlbit = S3C2410_CLKCON_LCDC - }, - { .name = "usb-host", - .id = -1, - .parent = &clk_h, - .enable = s3c24xx_clkcon_enable, - .ctrlbit = S3C2410_CLKCON_USBH - }, - { .name = "usb-device", - .id = -1, - .parent = &clk_h, - .enable = s3c24xx_clkcon_enable, - .ctrlbit = S3C2410_CLKCON_USBD - }, - { .name = "timers", - .id = -1, - .parent = &clk_p, - .enable = s3c24xx_clkcon_enable, - .ctrlbit = S3C2410_CLKCON_PWMT - }, - { .name = "sdi", - .id = -1, - .parent = &clk_p, - .enable = s3c24xx_clkcon_enable, - .ctrlbit = S3C2410_CLKCON_SDI - }, - { .name = "uart", - .id = 0, - .parent = &clk_p, - .enable = s3c24xx_clkcon_enable, - .ctrlbit = S3C2410_CLKCON_UART0 - }, - { .name = "uart", - .id = 1, - .parent = &clk_p, - .enable = s3c24xx_clkcon_enable, - .ctrlbit = S3C2410_CLKCON_UART1 - }, - { .name = "uart", - .id = 2, - .parent = &clk_p, - .enable = s3c24xx_clkcon_enable, - .ctrlbit = S3C2410_CLKCON_UART2 - }, - { .name = "gpio", - .id = -1, - .parent = &clk_p, - .enable = s3c24xx_clkcon_enable, - .ctrlbit = S3C2410_CLKCON_GPIO - }, - { .name = "rtc", - .id = -1, - .parent = &clk_p, - .enable = s3c24xx_clkcon_enable, - .ctrlbit = S3C2410_CLKCON_RTC - }, - { .name = "adc", - .id = -1, - .parent = &clk_p, - .enable = s3c24xx_clkcon_enable, - .ctrlbit = S3C2410_CLKCON_ADC - }, - { .name = "i2c", - .id = -1, - .parent = &clk_p, - .enable = s3c24xx_clkcon_enable, - .ctrlbit = S3C2410_CLKCON_IIC - }, - { .name = "iis", - .id = -1, - .parent = &clk_p, - .enable = s3c24xx_clkcon_enable, - .ctrlbit = S3C2410_CLKCON_IIS - }, - { .name = "spi", - .id = -1, - .parent = &clk_p, - .enable = s3c24xx_clkcon_enable, - .ctrlbit = S3C2410_CLKCON_SPI - }, - { .name = "watchdog", - .id = -1, - .parent = &clk_p, - .ctrlbit = 0 + { + .name = "nand", + .id = -1, + .parent = &clk_h, + .enable = s3c24xx_clkcon_enable, + .ctrlbit = S3C2410_CLKCON_NAND, + }, { + .name = "lcd", + .id = -1, + .parent = &clk_h, + .enable = s3c24xx_clkcon_enable, + .ctrlbit = S3C2410_CLKCON_LCDC, + }, { + .name = "usb-host", + .id = -1, + .parent = &clk_h, + .enable = s3c24xx_clkcon_enable, + .ctrlbit = S3C2410_CLKCON_USBH, + }, { + .name = "usb-device", + .id = -1, + .parent = &clk_h, + .enable = s3c24xx_clkcon_enable, + .ctrlbit = S3C2410_CLKCON_USBD, + }, { + .name = "timers", + .id = -1, + .parent = &clk_p, + .enable = s3c24xx_clkcon_enable, + .ctrlbit = S3C2410_CLKCON_PWMT, + }, { + .name = "sdi", + .id = -1, + .parent = &clk_p, + .enable = s3c24xx_clkcon_enable, + .ctrlbit = S3C2410_CLKCON_SDI, + }, { + .name = "uart", + .id = 0, + .parent = &clk_p, + .enable = s3c24xx_clkcon_enable, + .ctrlbit = S3C2410_CLKCON_UART0, + }, { + .name = "uart", + .id = 1, + .parent = &clk_p, + .enable = s3c24xx_clkcon_enable, + .ctrlbit = S3C2410_CLKCON_UART1, + }, { + .name = "uart", + .id = 2, + .parent = &clk_p, + .enable = s3c24xx_clkcon_enable, + .ctrlbit = S3C2410_CLKCON_UART2, + }, { + .name = "gpio", + .id = -1, + .parent = &clk_p, + .enable = s3c24xx_clkcon_enable, + .ctrlbit = S3C2410_CLKCON_GPIO, + }, { + .name = "rtc", + .id = -1, + .parent = &clk_p, + .enable = s3c24xx_clkcon_enable, + .ctrlbit = S3C2410_CLKCON_RTC, + }, { + .name = "adc", + .id = -1, + .parent = &clk_p, + .enable = s3c24xx_clkcon_enable, + .ctrlbit = S3C2410_CLKCON_ADC, + }, { + .name = "i2c", + .id = -1, + .parent = &clk_p, + .enable = s3c24xx_clkcon_enable, + .ctrlbit = S3C2410_CLKCON_IIC, + }, { + .name = "iis", + .id = -1, + .parent = &clk_p, + .enable = s3c24xx_clkcon_enable, + .ctrlbit = S3C2410_CLKCON_IIS, + }, { + .name = "spi", + .id = -1, + .parent = &clk_p, + .enable = s3c24xx_clkcon_enable, + .ctrlbit = S3C2410_CLKCON_SPI, + }, { + .name = "watchdog", + .id = -1, + .parent = &clk_p, + .ctrlbit = 0, } }; @@ -390,16 +391,15 @@ int __init s3c24xx_setup_clocks(unsigned long xtal, clk_p.rate = pclk; clk_f.rate = fclk; - /* it looks like just setting the register here is not good - * enough, and causes the odd hang at initial boot time, so - * do all of them indivdually. + /* We must be careful disabling the clocks we are not intending to + * be using at boot time, as subsytems such as the LCD which do + * their own DMA requests to the bus can cause the system to lockup + * if they where in the middle of requesting bus access. * - * I think disabling the LCD clock if the LCD is active is - * very dangerous, and therefore the bootloader should be - * careful to not enable the LCD clock if it is not needed. - * - * and of course, this looks neater - */ + * Disabling the LCD clock if the LCD is active is very dangerous, + * and therefore the bootloader should be careful to not enable + * the LCD clock if it is not needed. + */ s3c24xx_clk_enable(S3C2410_CLKCON_NAND, 0); s3c24xx_clk_enable(S3C2410_CLKCON_USBH, 0); diff --git a/arch/arm/mm/Kconfig b/arch/arm/mm/Kconfig index e84fdde6edf8..3b79d0e23455 100644 --- a/arch/arm/mm/Kconfig +++ b/arch/arm/mm/Kconfig @@ -62,8 +62,8 @@ config CPU_ARM720T # ARM920T config CPU_ARM920T bool "Support ARM920T processor" if !ARCH_S3C2410 - depends on ARCH_INTEGRATOR || ARCH_S3C2410 || ARCH_IMX || ARCH_AAEC2000 - default y if ARCH_S3C2410 + depends on ARCH_INTEGRATOR || ARCH_S3C2410 || ARCH_IMX || ARCH_AAEC2000 || ARCH_AT91RM9200 + default y if ARCH_S3C2410 || ARCH_AT91RM9200 select CPU_32v4 select CPU_ABRT_EV4T select CPU_CACHE_V4WT @@ -83,8 +83,8 @@ config CPU_ARM920T # ARM922T config CPU_ARM922T bool "Support ARM922T processor" if ARCH_INTEGRATOR - depends on ARCH_CAMELOT || ARCH_LH7A40X || ARCH_INTEGRATOR - default y if ARCH_CAMELOT || ARCH_LH7A40X + depends on ARCH_LH7A40X || ARCH_INTEGRATOR + default y if ARCH_LH7A40X select CPU_32v4 select CPU_ABRT_EV4T select CPU_CACHE_V4WT diff --git a/arch/arm/mm/ioremap.c b/arch/arm/mm/ioremap.c index 10901398e4a2..de3ce1eec2ec 100644 --- a/arch/arm/mm/ioremap.c +++ b/arch/arm/mm/ioremap.c @@ -86,11 +86,12 @@ remap_area_pmd(pmd_t * pmd, unsigned long address, unsigned long size, } static int -remap_area_pages(unsigned long start, unsigned long phys_addr, +remap_area_pages(unsigned long start, unsigned long pfn, unsigned long size, unsigned long flags) { unsigned long address = start; unsigned long end = start + size; + unsigned long phys_addr = __pfn_to_phys(pfn); int err = 0; pgd_t * dir; @@ -130,36 +131,44 @@ remap_area_pages(unsigned long start, unsigned long phys_addr, * mapping. See include/asm-arm/proc-armv/pgtable.h for more information. */ void __iomem * +__ioremap_pfn(unsigned long pfn, unsigned long offset, size_t size, + unsigned long flags) +{ + unsigned long addr; + struct vm_struct * area; + + area = get_vm_area(size, VM_IOREMAP); + if (!area) + return NULL; + addr = (unsigned long)area->addr; + if (remap_area_pages(addr, pfn, size, flags)) { + vfree(addr); + return NULL; + } + return (void __iomem *) (offset + (char *)addr); +} +EXPORT_SYMBOL(__ioremap_pfn); + +void __iomem * __ioremap(unsigned long phys_addr, size_t size, unsigned long flags) { - void * addr; - struct vm_struct * area; - unsigned long offset, last_addr; + unsigned long last_addr; + unsigned long offset = phys_addr & ~PAGE_MASK; + unsigned long pfn = __phys_to_pfn(phys_addr); - /* Don't allow wraparound or zero size */ + /* + * Don't allow wraparound or zero size + */ last_addr = phys_addr + size - 1; if (!size || last_addr < phys_addr) return NULL; /* - * Mappings have to be page-aligned + * Page align the mapping size */ - offset = phys_addr & ~PAGE_MASK; - phys_addr &= PAGE_MASK; size = PAGE_ALIGN(last_addr + 1) - phys_addr; - /* - * Ok, go for it.. - */ - area = get_vm_area(size, VM_IOREMAP); - if (!area) - return NULL; - addr = area->addr; - if (remap_area_pages((unsigned long) addr, phys_addr, size, flags)) { - vfree(addr); - return NULL; - } - return (void __iomem *) (offset + (char *)addr); + return __ioremap_pfn(pfn, offset, size, flags); } EXPORT_SYMBOL(__ioremap); diff --git a/arch/arm/tools/mach-types b/arch/arm/tools/mach-types index 465487470d0e..d0f9bb5e9023 100644 --- a/arch/arm/tools/mach-types +++ b/arch/arm/tools/mach-types @@ -12,7 +12,7 @@ # # http://www.arm.linux.org.uk/developer/machines/?action=new # -# Last update: Fri Nov 25 14:43:04 2005 +# Last update: Mon Jan 9 12:56:42 2006 # # machine_is_xxx CONFIG_xxxx MACH_TYPE_xxx number # @@ -910,3 +910,31 @@ mbus MACH_MBUS MBUS 896 nadia2vb MACH_NADIA2VB NADIA2VB 897 r1000 MACH_R1000 R1000 898 hw90250 MACH_HW90250 HW90250 899 +omap_2430sdp MACH_OMAP_2430SDP OMAP_2430SDP 900 +davinci_evm MACH_DAVINCI_EVM DAVINCI_EVM 901 +omap_tornado MACH_OMAP_TORNADO OMAP_TORNADO 902 +olocreek MACH_OLOCREEK OLOCREEK 903 +palmz72 MACH_PALMZ72 PALMZ72 904 +nxdb500 MACH_NXDB500 NXDB500 905 +apf9328 MACH_APF9328 APF9328 906 +omap_wipoq MACH_OMAP_WIPOQ OMAP_WIPOQ 907 +omap_twip MACH_OMAP_TWIP OMAP_TWIP 908 +xscale_treo650 MACH_XSCALE_PALMTREO650 XSCALE_PALMTREO650 909 +acumen MACH_ACUMEN ACUMEN 910 +xp100 MACH_XP100 XP100 911 +fs2410 MACH_FS2410 FS2410 912 +pxa270_cerf MACH_PXA270_CERF PXA270_CERF 913 +sq2ftlpalm MACH_SQ2FTLPALM SQ2FTLPALM 914 +bsemserver MACH_BSEMSERVER BSEMSERVER 915 +netclient MACH_NETCLIENT NETCLIENT 916 +xscale_palmtt5 MACH_XSCALE_PALMTT5 XSCALE_PALMTT5 917 +xscale_palmtc MACH_OMAP_PALMTC OMAP_PALMTC 918 +omap_apollon MACH_OMAP_APOLLON OMAP_APOLLON 919 +argonlvevb MACH_ARGONLVEVB ARGONLVEVB 920 +rea_2d MACH_REA_2D REA_2D 921 +eti3e524 MACH_TI3E524 TI3E524 922 +ateb9200 MACH_ATEB9200 ATEB9200 923 +auckland MACH_AUCKLAND AUCKLAND 924 +ak3220m MACH_AK3320M AK3320M 925 +duramax MACH_DURAMAX DURAMAX 926 +n35 MACH_N35 N35 927 |