diff options
| -rw-r--r-- | drivers/usb/host/xhci-pci.c | 90 |
1 files changed, 45 insertions, 45 deletions
diff --git a/drivers/usb/host/xhci-pci.c b/drivers/usb/host/xhci-pci.c index 5590eac2b22d..c79d33676672 100644 --- a/drivers/usb/host/xhci-pci.c +++ b/drivers/usb/host/xhci-pci.c @@ -180,51 +180,6 @@ static void xhci_pci_quirks(struct device *dev, struct xhci_hcd *xhci) "QUIRK: Resetting on resume"); } -/* - * In some Intel xHCI controllers, in order to get D3 working, - * through a vendor specific SSIC CONFIG register at offset 0x883c, - * SSIC PORT need to be marked as "unused" before putting xHCI - * into D3. After D3 exit, the SSIC port need to be marked as "used". - * Without this change, xHCI might not enter D3 state. - * Make sure PME works on some Intel xHCI controllers by writing 1 to clear - * the Internal PME flag bit in vendor specific PMCTRL register at offset 0x80a4 - */ -static void xhci_pme_quirk(struct usb_hcd *hcd, bool suspend) -{ - struct xhci_hcd *xhci = hcd_to_xhci(hcd); - struct pci_dev *pdev = to_pci_dev(hcd->self.controller); - u32 val; - void __iomem *reg; - - if (pdev->vendor == PCI_VENDOR_ID_INTEL && - pdev->device == PCI_DEVICE_ID_INTEL_CHERRYVIEW_XHCI) { - - reg = (void __iomem *) xhci->cap_regs + PORT2_SSIC_CONFIG_REG2; - - /* Notify SSIC that SSIC profile programming is not done */ - val = readl(reg) & ~PROG_DONE; - writel(val, reg); - - /* Mark SSIC port as unused(suspend) or used(resume) */ - val = readl(reg); - if (suspend) - val |= SSIC_PORT_UNUSED; - else - val &= ~SSIC_PORT_UNUSED; - writel(val, reg); - - /* Notify SSIC that SSIC profile programming is done */ - val = readl(reg) | PROG_DONE; - writel(val, reg); - readl(reg); - } - - reg = (void __iomem *) xhci->cap_regs + 0x80a4; - val = readl(reg); - writel(val | BIT(28), reg); - readl(reg); -} - #ifdef CONFIG_ACPI static void xhci_pme_acpi_rtd3_enable(struct pci_dev *dev) { @@ -345,6 +300,51 @@ static void xhci_pci_remove(struct pci_dev *dev) } #ifdef CONFIG_PM +/* + * In some Intel xHCI controllers, in order to get D3 working, + * through a vendor specific SSIC CONFIG register at offset 0x883c, + * SSIC PORT need to be marked as "unused" before putting xHCI + * into D3. After D3 exit, the SSIC port need to be marked as "used". + * Without this change, xHCI might not enter D3 state. + * Make sure PME works on some Intel xHCI controllers by writing 1 to clear + * the Internal PME flag bit in vendor specific PMCTRL register at offset 0x80a4 + */ +static void xhci_pme_quirk(struct usb_hcd *hcd, bool suspend) +{ + struct xhci_hcd *xhci = hcd_to_xhci(hcd); + struct pci_dev *pdev = to_pci_dev(hcd->self.controller); + u32 val; + void __iomem *reg; + + if (pdev->vendor == PCI_VENDOR_ID_INTEL && + pdev->device == PCI_DEVICE_ID_INTEL_CHERRYVIEW_XHCI) { + + reg = (void __iomem *) xhci->cap_regs + PORT2_SSIC_CONFIG_REG2; + + /* Notify SSIC that SSIC profile programming is not done */ + val = readl(reg) & ~PROG_DONE; + writel(val, reg); + + /* Mark SSIC port as unused(suspend) or used(resume) */ + val = readl(reg); + if (suspend) + val |= SSIC_PORT_UNUSED; + else + val &= ~SSIC_PORT_UNUSED; + writel(val, reg); + + /* Notify SSIC that SSIC profile programming is done */ + val = readl(reg) | PROG_DONE; + writel(val, reg); + readl(reg); + } + + reg = (void __iomem *) xhci->cap_regs + 0x80a4; + val = readl(reg); + writel(val | BIT(28), reg); + readl(reg); +} + static int xhci_pci_suspend(struct usb_hcd *hcd, bool do_wakeup) { struct xhci_hcd *xhci = hcd_to_xhci(hcd); |