Linux-2.6.12-rc2

Initial git repository build. I'm not bothering with the full history,
even though we have it. We can create a separate "historical" git
archive of that later if we want to, and in the meantime it's about
3.2GB when imported into git - space that would just make the early
git days unnecessarily complicated, when we don't have a lot of good
infrastructure for it.

Let it rip!

1 files changed, 351 insertions, 0 deletions

diff --git a/include/linux/mtio.h b/include/linux/mtio.h
new file mode 100644
index 000000000000..8c66151821e3
--- /dev/null
+++ b/include/linux/mtio.h
@@ -0,0 +1,351 @@
+/* 
+ * linux/mtio.h header file for Linux. Written by H. Bergman
+ *
+ * Modified for special ioctls provided by zftape in September 1997
+ * by C.-J. Heine.
+ */
+
+#ifndef _LINUX_MTIO_H
+#define _LINUX_MTIO_H
+
+#include <linux/types.h>
+#include <linux/ioctl.h>
+#include <linux/qic117.h>
+
+/*
+ * Structures and definitions for mag tape io control commands
+ */
+
+/* structure for MTIOCTOP - mag tape op command */
+struct	mtop {
+	short	mt_op;		/* operations defined below */
+	int	mt_count;	/* how many of them */
+};
+
+/* Magnetic Tape operations [Not all operations supported by all drivers]: */
+#define MTRESET 0	/* +reset drive in case of problems */
+#define MTFSF	1	/* forward space over FileMark,
+			 * position at first record of next file 
+			 */
+#define MTBSF	2	/* backward space FileMark (position before FM) */
+#define MTFSR	3	/* forward space record */
+#define MTBSR	4	/* backward space record */
+#define MTWEOF	5	/* write an end-of-file record (mark) */
+#define MTREW	6	/* rewind */
+#define MTOFFL	7	/* rewind and put the drive offline (eject?) */
+#define MTNOP	8	/* no op, set status only (read with MTIOCGET) */
+#define MTRETEN 9	/* retension tape */
+#define MTBSFM	10	/* +backward space FileMark, position at FM */
+#define MTFSFM  11	/* +forward space FileMark, position at FM */
+#define MTEOM	12	/* goto end of recorded media (for appending files).
+			 * MTEOM positions after the last FM, ready for
+			 * appending another file.
+			 */
+#define MTERASE 13	/* erase tape -- be careful! */
+
+#define MTRAS1  14	/* run self test 1 (nondestructive) */
+#define MTRAS2	15	/* run self test 2 (destructive) */
+#define MTRAS3  16	/* reserved for self test 3 */
+
+#define MTSETBLK 20	/* set block length (SCSI) */
+#define MTSETDENSITY 21	/* set tape density (SCSI) */
+#define MTSEEK	22	/* seek to block (Tandberg, etc.) */
+#define MTTELL	23	/* tell block (Tandberg, etc.) */
+#define MTSETDRVBUFFER 24 /* set the drive buffering according to SCSI-2 */
+			/* ordinary buffered operation with code 1 */
+#define MTFSS	25	/* space forward over setmarks */
+#define MTBSS	26	/* space backward over setmarks */
+#define MTWSM	27	/* write setmarks */
+
+#define MTLOCK  28	/* lock the drive door */
+#define MTUNLOCK 29	/* unlock the drive door */
+#define MTLOAD  30	/* execute the SCSI load command */
+#define MTUNLOAD 31	/* execute the SCSI unload command */
+#define MTCOMPRESSION 32/* control compression with SCSI mode page 15 */
+#define MTSETPART 33	/* Change the active tape partition */
+#define MTMKPART  34	/* Format the tape with one or two partitions */
+
+/* structure for MTIOCGET - mag tape get status command */
+
+struct	mtget {
+	long	mt_type;	/* type of magtape device */
+	long	mt_resid;	/* residual count: (not sure)
+				 *	number of bytes ignored, or
+				 *	number of files not skipped, or
+				 *	number of records not skipped.
+				 */
+	/* the following registers are device dependent */
+	long	mt_dsreg;	/* status register */
+	long	mt_gstat;	/* generic (device independent) status */
+	long	mt_erreg;	/* error register */
+	/* The next two fields are not always used */
+	__kernel_daddr_t mt_fileno;	/* number of current file on tape */
+	__kernel_daddr_t mt_blkno;	/* current block number */
+};
+
+
+
+/*
+ * Constants for mt_type. Not all of these are supported,
+ * and these are not all of the ones that are supported.
+ */
+#define MT_ISUNKNOWN		0x01
+#define MT_ISQIC02		0x02	/* Generic QIC-02 tape streamer */
+#define MT_ISWT5150		0x03	/* Wangtek 5150EQ, QIC-150, QIC-02 */
+#define MT_ISARCHIVE_5945L2	0x04	/* Archive 5945L-2, QIC-24, QIC-02? */
+#define MT_ISCMSJ500		0x05	/* CMS Jumbo 500 (QIC-02?) */
+#define MT_ISTDC3610		0x06	/* Tandberg 6310, QIC-24 */
+#define MT_ISARCHIVE_VP60I	0x07	/* Archive VP60i, QIC-02 */
+#define MT_ISARCHIVE_2150L	0x08	/* Archive Viper 2150L */
+#define MT_ISARCHIVE_2060L	0x09	/* Archive Viper 2060L */
+#define MT_ISARCHIVESC499	0x0A	/* Archive SC-499 QIC-36 controller */
+#define MT_ISQIC02_ALL_FEATURES	0x0F	/* Generic QIC-02 with all features */
+#define MT_ISWT5099EEN24	0x11	/* Wangtek 5099-een24, 60MB, QIC-24 */
+#define MT_ISTEAC_MT2ST		0x12	/* Teac MT-2ST 155mb drive, Teac DC-1 card (Wangtek type) */
+#define MT_ISEVEREX_FT40A	0x32	/* Everex FT40A (QIC-40) */
+#define MT_ISDDS1		0x51	/* DDS device without partitions */
+#define MT_ISDDS2		0x52	/* DDS device with partitions */
+#define MT_ISONSTREAM_SC        0x61   /* OnStream SCSI tape drives (SC-x0)
+					  and SCSI emulated (DI, DP, USB) */
+#define MT_ISSCSI1		0x71	/* Generic ANSI SCSI-1 tape unit */
+#define MT_ISSCSI2		0x72	/* Generic ANSI SCSI-2 tape unit */
+
+/* QIC-40/80/3010/3020 ftape supported drives.
+ * 20bit vendor ID + 0x800000 (see ftape-vendors.h)
+ */
+#define MT_ISFTAPE_UNKNOWN	0x800000 /* obsolete */
+#define MT_ISFTAPE_FLAG	0x800000
+
+struct mt_tape_info {
+	long t_type;		/* device type id (mt_type) */
+	char *t_name;		/* descriptive name */
+};
+
+#define MT_TAPE_INFO	{ \
+	{MT_ISUNKNOWN,		"Unknown type of tape device"}, \
+	{MT_ISQIC02,		"Generic QIC-02 tape streamer"}, \
+	{MT_ISWT5150,		"Wangtek 5150, QIC-150"}, \
+	{MT_ISARCHIVE_5945L2,	"Archive 5945L-2"}, \
+	{MT_ISCMSJ500,		"CMS Jumbo 500"}, \
+	{MT_ISTDC3610,		"Tandberg TDC 3610, QIC-24"}, \
+	{MT_ISARCHIVE_VP60I,	"Archive VP60i, QIC-02"}, \
+	{MT_ISARCHIVE_2150L,	"Archive Viper 2150L"}, \
+	{MT_ISARCHIVE_2060L,	"Archive Viper 2060L"}, \
+	{MT_ISARCHIVESC499,	"Archive SC-499 QIC-36 controller"}, \
+	{MT_ISQIC02_ALL_FEATURES, "Generic QIC-02 tape, all features"}, \
+	{MT_ISWT5099EEN24,	"Wangtek 5099-een24, 60MB"}, \
+	{MT_ISTEAC_MT2ST,	"Teac MT-2ST 155mb data cassette drive"}, \
+	{MT_ISEVEREX_FT40A,	"Everex FT40A, QIC-40"}, \
+	{MT_ISONSTREAM_SC,      "OnStream SC-, DI-, DP-, or USB tape drive"}, \
+	{MT_ISSCSI1,		"Generic SCSI-1 tape"}, \
+	{MT_ISSCSI2,		"Generic SCSI-2 tape"}, \
+	{0, NULL} \
+}
+
+
+/* structure for MTIOCPOS - mag tape get position command */
+
+struct	mtpos {
+	long 	mt_blkno;	/* current block number */
+};
+
+
+/*  structure for MTIOCVOLINFO, query information about the volume
+ *  currently positioned at (zftape)
+ */
+struct mtvolinfo {
+	unsigned int mt_volno;   /* vol-number */
+	unsigned int mt_blksz;   /* blocksize used when recording */
+	unsigned int mt_rawsize; /* raw tape space consumed, in kb */
+	unsigned int mt_size;    /* volume size after decompression, in kb */
+	unsigned int mt_cmpr:1;  /* this volume has been compressed */
+};
+
+/* raw access to a floppy drive, read and write an arbitrary segment.
+ * For ftape/zftape to support formatting etc.
+ */
+#define MT_FT_RD_SINGLE  0
+#define MT_FT_RD_AHEAD   1
+#define MT_FT_WR_ASYNC   0 /* start tape only when all buffers are full     */
+#define MT_FT_WR_MULTI   1 /* start tape, continue until buffers are empty  */
+#define MT_FT_WR_SINGLE  2 /* write a single segment and stop afterwards    */
+#define MT_FT_WR_DELETE  3 /* write deleted data marks, one segment at time */
+
+struct mtftseg
+{            
+	unsigned mt_segno;   /* the segment to read or write */
+	unsigned mt_mode;    /* modes for read/write (sync/async etc.) */
+	int      mt_result;  /* result of r/w request, not of the ioctl */
+	void    __user *mt_data;    /* User space buffer: must be 29kb */
+};
+
+/* get tape capacity (ftape/zftape)
+ */
+struct mttapesize {
+	unsigned long mt_capacity; /* entire, uncompressed capacity 
+				    * of a cartridge
+				    */
+	unsigned long mt_used;     /* what has been used so far, raw 
+				    * uncompressed amount
+				    */
+};
+
+/*  possible values of the ftfmt_op field
+ */
+#define FTFMT_SET_PARMS		1 /* set software parms */
+#define FTFMT_GET_PARMS		2 /* get software parms */
+#define FTFMT_FORMAT_TRACK	3 /* start formatting a tape track   */
+#define FTFMT_STATUS		4 /* monitor formatting a tape track */
+#define FTFMT_VERIFY		5 /* verify the given segment        */
+
+struct ftfmtparms {
+	unsigned char  ft_qicstd;   /* QIC-40/QIC-80/QIC-3010/QIC-3020 */
+	unsigned char  ft_fmtcode;  /* Refer to the QIC specs */
+	unsigned char  ft_fhm;      /* floppy head max */
+	unsigned char  ft_ftm;      /* floppy track max */
+	unsigned short ft_spt;      /* segments per track */
+	unsigned short ft_tpc;      /* tracks per cartridge */
+};
+
+struct ftfmttrack {
+	unsigned int  ft_track;   /* track to format */
+	unsigned char ft_gap3;    /* size of gap3, for FORMAT_TRK */
+};
+
+struct ftfmtstatus {
+	unsigned int  ft_segment;  /* segment currently being formatted */
+};
+
+struct ftfmtverify {
+	unsigned int  ft_segment;   /* segment to verify */
+	unsigned long ft_bsm;       /* bsm as result of VERIFY cmd */
+};
+
+struct mtftformat {
+	unsigned int fmt_op;      /* operation to perform */
+	union fmt_arg {
+		struct ftfmtparms  fmt_parms;  /* format parameters */
+		struct ftfmttrack  fmt_track;  /* ctrl while formatting */
+		struct ftfmtstatus fmt_status;
+		struct ftfmtverify fmt_verify; /* for verifying */ 
+	} fmt_arg;
+};
+
+struct mtftcmd {
+	unsigned int ft_wait_before; /* timeout to wait for drive to get ready 
+				      * before command is sent. Milliseconds
+				      */
+	qic117_cmd_t ft_cmd;         /* command to send */
+	unsigned char ft_parm_cnt;   /* zero: no parm is sent. */
+	unsigned char ft_parms[3];   /* parameter(s) to send to
+				      * the drive. The parms are nibbles
+				      * driver sends cmd + 2 step pulses */
+	unsigned int ft_result_bits; /* if non zero, number of bits
+				      *	returned by the tape drive
+				      */
+	unsigned int ft_result;      /* the result returned by the tape drive*/
+	unsigned int ft_wait_after;  /* timeout to wait for drive to get ready
+				      * after command is sent. 0: don't wait */
+	int ft_status;	             /* status returned by ready wait
+				      * undefined if timeout was 0.
+				      */
+	int ft_error;                /* error code if error status was set by 
+				      * command
+				      */
+};
+
+/* mag tape io control commands */
+#define	MTIOCTOP	_IOW('m', 1, struct mtop)	/* do a mag tape op */
+#define	MTIOCGET	_IOR('m', 2, struct mtget)	/* get tape status */
+#define	MTIOCPOS	_IOR('m', 3, struct mtpos)	/* get tape position */
+
+/* The next two are used by the QIC-02 driver for runtime reconfiguration.
+ * See tpqic02.h for struct mtconfiginfo.
+ */
+#define	MTIOCGETCONFIG	_IOR('m', 4, struct mtconfiginfo) /* get tape config */
+#define	MTIOCSETCONFIG	_IOW('m', 5, struct mtconfiginfo) /* set tape config */
+
+/* the next six are used by the floppy ftape drivers and its frontends
+ * sorry, but MTIOCTOP commands are write only.
+ */
+#define	MTIOCRDFTSEG    _IOWR('m', 6, struct mtftseg)  /* read a segment */
+#define	MTIOCWRFTSEG    _IOWR('m', 7, struct mtftseg)   /* write a segment */
+#define MTIOCVOLINFO	_IOR('m',  8, struct mtvolinfo) /* info about volume */
+#define MTIOCGETSIZE    _IOR('m',  9, struct mttapesize)/* get cartridge size*/
+#define MTIOCFTFORMAT   _IOWR('m', 10, struct mtftformat) /* format ftape */
+#define MTIOCFTCMD	_IOWR('m', 11, struct mtftcmd) /* send QIC-117 cmd */
+
+/* Generic Mag Tape (device independent) status macros for examining
+ * mt_gstat -- HP-UX compatible.
+ * There is room for more generic status bits here, but I don't
+ * know which of them are reserved. At least three or so should
+ * be added to make this really useful.
+ */
+#define GMT_EOF(x)              ((x) & 0x80000000)
+#define GMT_BOT(x)              ((x) & 0x40000000)
+#define GMT_EOT(x)              ((x) & 0x20000000)
+#define GMT_SM(x)               ((x) & 0x10000000)  /* DDS setmark */
+#define GMT_EOD(x)              ((x) & 0x08000000)  /* DDS EOD */
+#define GMT_WR_PROT(x)          ((x) & 0x04000000)
+/* #define GMT_ ? 		((x) & 0x02000000) */
+#define GMT_ONLINE(x)           ((x) & 0x01000000)
+#define GMT_D_6250(x)           ((x) & 0x00800000)
+#define GMT_D_1600(x)           ((x) & 0x00400000)
+#define GMT_D_800(x)            ((x) & 0x00200000)
+/* #define GMT_ ? 		((x) & 0x00100000) */
+/* #define GMT_ ? 		((x) & 0x00080000) */
+#define GMT_DR_OPEN(x)          ((x) & 0x00040000)  /* door open (no tape) */
+/* #define GMT_ ? 		((x) & 0x00020000) */
+#define GMT_IM_REP_EN(x)        ((x) & 0x00010000)  /* immediate report mode */
+#define GMT_CLN(x)              ((x) & 0x00008000)  /* cleaning requested */
+/* 15 generic status bits unused */
+
+
+/* SCSI-tape specific definitions */
+/* Bitfield shifts in the status  */
+#define MT_ST_BLKSIZE_SHIFT	0
+#define MT_ST_BLKSIZE_MASK	0xffffff
+#define MT_ST_DENSITY_SHIFT	24
+#define MT_ST_DENSITY_MASK	0xff000000
+
+#define MT_ST_SOFTERR_SHIFT	0
+#define MT_ST_SOFTERR_MASK	0xffff
+
+/* Bitfields for the MTSETDRVBUFFER ioctl */
+#define MT_ST_OPTIONS		0xf0000000
+#define MT_ST_BOOLEANS		0x10000000
+#define MT_ST_SETBOOLEANS	0x30000000
+#define MT_ST_CLEARBOOLEANS	0x40000000
+#define MT_ST_WRITE_THRESHOLD	0x20000000
+#define MT_ST_DEF_BLKSIZE	0x50000000
+#define MT_ST_DEF_OPTIONS	0x60000000
+#define MT_ST_TIMEOUTS		0x70000000
+#define MT_ST_SET_TIMEOUT	(MT_ST_TIMEOUTS | 0x000000)
+#define MT_ST_SET_LONG_TIMEOUT	(MT_ST_TIMEOUTS | 0x100000)
+#define MT_ST_SET_CLN		0x80000000
+
+#define MT_ST_BUFFER_WRITES	0x1
+#define MT_ST_ASYNC_WRITES	0x2
+#define MT_ST_READ_AHEAD	0x4
+#define MT_ST_DEBUGGING		0x8
+#define MT_ST_TWO_FM		0x10
+#define MT_ST_FAST_MTEOM	0x20
+#define MT_ST_AUTO_LOCK		0x40
+#define MT_ST_DEF_WRITES	0x80
+#define MT_ST_CAN_BSR		0x100
+#define MT_ST_NO_BLKLIMS	0x200
+#define MT_ST_CAN_PARTITIONS    0x400
+#define MT_ST_SCSI2LOGICAL      0x800
+#define MT_ST_SYSV              0x1000
+#define MT_ST_NOWAIT            0x2000
+
+/* The mode parameters to be controlled. Parameter chosen with bits 20-28 */
+#define MT_ST_CLEAR_DEFAULT	0xfffff
+#define MT_ST_DEF_DENSITY	(MT_ST_DEF_OPTIONS | 0x100000)
+#define MT_ST_DEF_COMPRESSION	(MT_ST_DEF_OPTIONS | 0x200000)
+#define MT_ST_DEF_DRVBUFFER	(MT_ST_DEF_OPTIONS | 0x300000)
+
+/* The offset for the arguments for the special HP changer load command. */
+#define MT_ST_HPLOADER_OFFSET 10000
+
+#endif /* _LINUX_MTIO_H */