phy: ufs-qcom: Refactor all init steps into phy_poweron

The phy code was using implicit sequencing between the PHY driver
and the UFS driver to implement certain hardware requirements.
Specifically, the PHY reset register in the UFS controller needs
to be deasserted before serdes start occurs in the PHY.

Before this change, the code was doing this by utilizing the two
phy callbacks, phy_init() and phy_poweron(), as "init step 1" and
"init step 2", where the UFS driver would deassert reset between
these two steps.

This makes it challenging to power off the regulators in suspend,
as regulators are initialized in init, not in poweron(), but only
poweroff() is called during suspend, not exit().

For UFS, move the actual firing up of the PHY to phy_poweron() and
phy_poweroff() callbacks, rather than init()/exit(). UFS calls
phy_poweroff() during suspend, so now all clocks and regulators for
the phy can be powered down during suspend.

QMP is a little tricky because the PHY is also shared with PCIe and
USB3, which have their own definitions for init() and poweron(). Rename
the meaty functions to _enable() and _disable() to disentangle from the
PHY core names, and then create two different ops structures: one for
UFS and one for the other PHY types.

In phy-qcom-ufs, remove the 'is_powered_on' and 'is_started' guards,
as the generic PHY code does the reference counting. The
14/20nm-specific init functions get collapsed into the generic power_on()
function, with the addition of a calibrate() callback specific to 14/20nm.

Signed-off-by: Evan Green <evgreen@chromium.org>
Reviewed-by: Stephen Boyd <swboyd@chromium.org>
Signed-off-by: Kishon Vijay Abraham I <kishon@ti.com>

1 files changed, 18 insertions, 26 deletions

diff --git a/drivers/scsi/ufs/ufs-qcom.c b/drivers/scsi/ufs/ufs-qcom.c
index 1c25b1c82314..de9d3f56b58c 100644
--- a/drivers/scsi/ufs/ufs-qcom.c
+++ b/drivers/scsi/ufs/ufs-qcom.c
@@ -544,19 +544,11 @@ static int ufs_qcom_suspend(struct ufs_hba *hba, enum ufs_pm_op pm_op)
 		 */
 		ufs_qcom_disable_lane_clks(host);
 		phy_power_off(phy);
-		goto out;
-	}
 
-	/*
-	 * If UniPro link is not active, PHY ref_clk, main PHY analog power
-	 * rail and low noise analog power rail for PLL can be switched off.
-	 */
-	if (!ufs_qcom_is_link_active(hba)) {
+	} else if (!ufs_qcom_is_link_active(hba)) {
 		ufs_qcom_disable_lane_clks(host);
-		phy_power_off(phy);
 	}
 
-out:
 	return ret;
 }
 
@@ -566,21 +558,26 @@ static int ufs_qcom_resume(struct ufs_hba *hba, enum ufs_pm_op pm_op)
 	struct phy *phy = host->generic_phy;
 	int err;
 
-	err = phy_power_on(phy);
-	if (err) {
-		dev_err(hba->dev, "%s: failed enabling regs, err = %d\n",
-			__func__, err);
-		goto out;
-	}
+	if (ufs_qcom_is_link_off(hba)) {
+		err = phy_power_on(phy);
+		if (err) {
+			dev_err(hba->dev, "%s: failed PHY power on: %d\n",
+				__func__, err);
+			return err;
+		}
 
-	err = ufs_qcom_enable_lane_clks(host);
-	if (err)
-		goto out;
+		err = ufs_qcom_enable_lane_clks(host);
+		if (err)
+			return err;
 
-	hba->is_sys_suspended = false;
+	} else if (!ufs_qcom_is_link_active(hba)) {
+		err = ufs_qcom_enable_lane_clks(host);
+		if (err)
+			return err;
+	}
 
-out:
-	return err;
+	hba->is_sys_suspended = false;
+	return 0;
 }
 
 struct ufs_qcom_dev_params {
@@ -1106,8 +1103,6 @@ static int ufs_qcom_setup_clocks(struct ufs_hba *hba, bool on,
 		return 0;
 
 	if (on && (status == POST_CHANGE)) {
-		phy_power_on(host->generic_phy);
-
 		/* enable the device ref clock for HS mode*/
 		if (ufshcd_is_hs_mode(&hba->pwr_info))
 			ufs_qcom_dev_ref_clk_ctrl(host, true);
@@ -1119,9 +1114,6 @@ static int ufs_qcom_setup_clocks(struct ufs_hba *hba, bool on,
 		if (!ufs_qcom_is_link_active(hba)) {
 			/* disable device ref_clk */
 			ufs_qcom_dev_ref_clk_ctrl(host, false);
-
-			/* powering off PHY during aggressive clk gating */
-			phy_power_off(host->generic_phy);
 		}
 
 		vote = host->bus_vote.min_bw_vote;