Merge tag 'omap-for-v4.4/dt-pt2' of git://git.kernel.org/pub/scm/linux/kernel/git/tmlind/linux-omap into next/dt

Merge "omap dts changes for v4.4 merge window, part 2" from Tony Lindgren:

Few more omap dts changes for v4.4 merge window, mostly to fix and clean
up some omap5 issues to allow adding other omap5 boards. Also some other
fixes and clean-up:

- Fix SDIO WLAN for omap5 that's been broken for a while. As further
  patches are still needed for wl18xx, no need for stable on this one.

- Move most of omap5 support into omap5-board-common.dtsi as most omap5
  boards seem to share the same basic set of devices.

- Add minimal IGEPv5 support using based on omap5-board-common.dtsi

- Remove now unneedes gpio hogging for dra72-evm

- Update Javier Martinez Canillas email address

- Change earlier IGEP boards to use IOPAD pinmux macros

* tag 'omap-for-v4.4/dt-pt2' of git://git.kernel.org/pub/scm/linux/kernel/git/tmlind/linux-omap:
  ARM: dts: am335x-base0033: Use IOPAD pinmux macro
  ARM: dts: am335x-igep0033: Use IOPAD pinmux macro
  ARM: dts: omap3-igep0020: Use IOPAD pinmux macro
  ARM: dts: am437x-gp-evm: Add wakeup interrupt source for pixcir_i2c_ts
  ARM: dts: Update Javier Martinez Canillas's email
  ARM: dts: dra72-evm: remove cpsw gpio hogging and add mode-gpios
  ARM: dts: Add basic support for isee igepv5
  ARM: dts: Move most of omap5-uevm.dts to omap5-board-common.dtsi
  ARM: dts: Fix WLAN regression on omap5-uevm

15 files changed, 814 insertions, 690 deletions

diff --git a/arch/arm/boot/dts/Makefile b/arch/arm/boot/dts/Makefile
index e6c76501c95c..b5e0ff97db15 100644
--- a/arch/arm/boot/dts/Makefile
+++ b/arch/arm/boot/dts/Makefile
@@ -481,6 +481,7 @@ dtb-$(CONFIG_SOC_AM43XX) += \
 	am437x-gp-evm.dtb
 dtb-$(CONFIG_SOC_OMAP5) += \
 	omap5-cm-t54.dtb \
+	omap5-igep0050.dtb \
 	omap5-sbc-t54.dtb \
 	omap5-uevm.dtb
 dtb-$(CONFIG_SOC_DRA7XX) += \
diff --git a/arch/arm/boot/dts/am335x-base0033.dts b/arch/arm/boot/dts/am335x-base0033.dts
index 72a9b3fc4251..58a05f7d0b7c 100644
--- a/arch/arm/boot/dts/am335x-base0033.dts
+++ b/arch/arm/boot/dts/am335x-base0033.dts
@@ -46,39 +46,39 @@
 &am33xx_pinmux {
 	nxp_hdmi_pins: pinmux_nxp_hdmi_pins {
 		pinctrl-single,pins = <
-			0x1b0 (PIN_OUTPUT | MUX_MODE3)	/* xdma_event_intr0.clkout1 */
-			0xa0 (PIN_OUTPUT | MUX_MODE0)	/* lcd_data0 */
-			0xa4 (PIN_OUTPUT | MUX_MODE0)	/* lcd_data1 */
-			0xa8 (PIN_OUTPUT | MUX_MODE0)	/* lcd_data2 */
-			0xac (PIN_OUTPUT | MUX_MODE0)	/* lcd_data3 */
-			0xb0 (PIN_OUTPUT | MUX_MODE0)	/* lcd_data4 */
-			0xb4 (PIN_OUTPUT | MUX_MODE0)	/* lcd_data5 */
-			0xb8 (PIN_OUTPUT | MUX_MODE0)	/* lcd_data6 */
-			0xbc (PIN_OUTPUT | MUX_MODE0)	/* lcd_data7 */
-			0xc0 (PIN_OUTPUT | MUX_MODE0)	/* lcd_data8 */
-			0xc4 (PIN_OUTPUT | MUX_MODE0)	/* lcd_data9 */
-			0xc8 (PIN_OUTPUT | MUX_MODE0)	/* lcd_data10 */
-			0xcc (PIN_OUTPUT | MUX_MODE0)	/* lcd_data11 */
-			0xd0 (PIN_OUTPUT | MUX_MODE0)	/* lcd_data12 */
-			0xd4 (PIN_OUTPUT | MUX_MODE0)	/* lcd_data13 */
-			0xd8 (PIN_OUTPUT | MUX_MODE0)	/* lcd_data14 */
-			0xdc (PIN_OUTPUT | MUX_MODE0)	/* lcd_data15 */
-			0xe0 (PIN_OUTPUT | MUX_MODE0)	/* lcd_vsync */
-			0xe4 (PIN_OUTPUT | MUX_MODE0)	/* lcd_hsync */
-			0xe8 (PIN_OUTPUT | MUX_MODE0)	/* lcd_pclk */
-			0xec (PIN_OUTPUT | MUX_MODE0)	/* lcd_ac_bias_en */
+			AM33XX_IOPAD(0x9b0, PIN_OUTPUT | MUX_MODE3)	/* xdma_event_intr0.clkout1 */
+			AM33XX_IOPAD(0x8a0, PIN_OUTPUT | MUX_MODE0)	/* lcd_data0 */
+			AM33XX_IOPAD(0x8a4, PIN_OUTPUT | MUX_MODE0)	/* lcd_data1 */
+			AM33XX_IOPAD(0x8a8, PIN_OUTPUT | MUX_MODE0)	/* lcd_data2 */
+			AM33XX_IOPAD(0x8ac, PIN_OUTPUT | MUX_MODE0)	/* lcd_data3 */
+			AM33XX_IOPAD(0x8b0, PIN_OUTPUT | MUX_MODE0)	/* lcd_data4 */
+			AM33XX_IOPAD(0x8b4, PIN_OUTPUT | MUX_MODE0)	/* lcd_data5 */
+			AM33XX_IOPAD(0x8b8, PIN_OUTPUT | MUX_MODE0)	/* lcd_data6 */
+			AM33XX_IOPAD(0x8bc, PIN_OUTPUT | MUX_MODE0)	/* lcd_data7 */
+			AM33XX_IOPAD(0x8c0, PIN_OUTPUT | MUX_MODE0)	/* lcd_data8 */
+			AM33XX_IOPAD(0x8c4, PIN_OUTPUT | MUX_MODE0)	/* lcd_data9 */
+			AM33XX_IOPAD(0x8c8, PIN_OUTPUT | MUX_MODE0)	/* lcd_data10 */
+			AM33XX_IOPAD(0x8cc, PIN_OUTPUT | MUX_MODE0)	/* lcd_data11 */
+			AM33XX_IOPAD(0x8d0, PIN_OUTPUT | MUX_MODE0)	/* lcd_data12 */
+			AM33XX_IOPAD(0x8d4, PIN_OUTPUT | MUX_MODE0)	/* lcd_data13 */
+			AM33XX_IOPAD(0x8d8, PIN_OUTPUT | MUX_MODE0)	/* lcd_data14 */
+			AM33XX_IOPAD(0x8dc, PIN_OUTPUT | MUX_MODE0)	/* lcd_data15 */
+			AM33XX_IOPAD(0x8e0, PIN_OUTPUT | MUX_MODE0)	/* lcd_vsync */
+			AM33XX_IOPAD(0x8e4, PIN_OUTPUT | MUX_MODE0)	/* lcd_hsync */
+			AM33XX_IOPAD(0x8e8, PIN_OUTPUT | MUX_MODE0)	/* lcd_pclk */
+			AM33XX_IOPAD(0x8ec, PIN_OUTPUT | MUX_MODE0)	/* lcd_ac_bias_en */
 		>;
 	};
 	nxp_hdmi_off_pins: pinmux_nxp_hdmi_off_pins {
 		pinctrl-single,pins = <
-			0x1b0 (PIN_OUTPUT | MUX_MODE3)	/* xdma_event_intr0.clkout1 */
+			AM33XX_IOPAD(0x9b0, PIN_OUTPUT | MUX_MODE3)	/* xdma_event_intr0.clkout1 */
 		>;
 	};
 
 	leds_base_pins: pinmux_leds_base_pins {
 		pinctrl-single,pins = <
-			0x54 (PIN_OUTPUT_PULLDOWN | MUX_MODE7)	/* gpmc_a5.gpio1_21 */
-			0x88 (PIN_OUTPUT_PULLDOWN | MUX_MODE7)	/* gpmc_csn3.gpio2_0 */
+			AM33XX_IOPAD(0x854, PIN_OUTPUT_PULLDOWN | MUX_MODE7)	/* gpmc_a5.gpio1_21 */
+			AM33XX_IOPAD(0x888, PIN_OUTPUT_PULLDOWN | MUX_MODE7)	/* gpmc_csn3.gpio2_0 */
 		>;
 	};
 };
diff --git a/arch/arm/boot/dts/am335x-igep0033.dtsi b/arch/arm/boot/dts/am335x-igep0033.dtsi
index c0e1135256cc..54f113546ecc 100644
--- a/arch/arm/boot/dts/am335x-igep0033.dtsi
+++ b/arch/arm/boot/dts/am335x-igep0033.dtsi
@@ -56,41 +56,41 @@
 &am33xx_pinmux {
 	i2c0_pins: pinmux_i2c0_pins {
 		pinctrl-single,pins = <
-			0x188 (PIN_INPUT_PULLUP | MUX_MODE0)	/* i2c0_sda.i2c0_sda */
-			0x18c (PIN_INPUT_PULLUP | MUX_MODE0)	/* i2c0_scl.i2c0_scl */
+			AM33XX_IOPAD(0x988, PIN_INPUT_PULLUP | MUX_MODE0)	/* i2c0_sda.i2c0_sda */
+			AM33XX_IOPAD(0x98c, PIN_INPUT_PULLUP | MUX_MODE0)	/* i2c0_scl.i2c0_scl */
 		>;
 	};
 
 	nandflash_pins: pinmux_nandflash_pins {
 		pinctrl-single,pins = <
-			0x0 (PIN_INPUT_PULLUP | MUX_MODE0)	/* gpmc_ad0.gpmc_ad0 */
-			0x4 (PIN_INPUT_PULLUP | MUX_MODE0)	/* gpmc_ad1.gpmc_ad1 */
-			0x8 (PIN_INPUT_PULLUP | MUX_MODE0)	/* gpmc_ad2.gpmc_ad2 */
-			0xc (PIN_INPUT_PULLUP | MUX_MODE0)	/* gpmc_ad3.gpmc_ad3 */
-			0x10 (PIN_INPUT_PULLUP | MUX_MODE0)	/* gpmc_ad4.gpmc_ad4 */
-			0x14 (PIN_INPUT_PULLUP | MUX_MODE0)	/* gpmc_ad5.gpmc_ad5 */
-			0x18 (PIN_INPUT_PULLUP | MUX_MODE0)	/* gpmc_ad6.gpmc_ad6 */
-			0x1c (PIN_INPUT_PULLUP | MUX_MODE0)	/* gpmc_ad7.gpmc_ad7 */
-			0x70 (PIN_INPUT_PULLUP | MUX_MODE0)	/* gpmc_wait0.gpmc_wait0 */
-			0x74 (PIN_INPUT_PULLUP | MUX_MODE7)	/* gpmc_wpn.gpio0_30 */
-			0x7c (PIN_OUTPUT | MUX_MODE0)		/* gpmc_csn0.gpmc_csn0 */
-			0x90 (PIN_OUTPUT | MUX_MODE0)		/* gpmc_advn_ale.gpmc_advn_ale */
-			0x94 (PIN_OUTPUT | MUX_MODE0)		/* gpmc_oen_ren.gpmc_oen_ren */
-			0x98 (PIN_OUTPUT | MUX_MODE0)		/* gpmc_wen.gpmc_wen */
-			0x9c (PIN_OUTPUT | MUX_MODE0)		/* gpmc_be0n_cle.gpmc_be0n_cle */
+			AM33XX_IOPAD(0x800, PIN_INPUT_PULLUP | MUX_MODE0)	/* gpmc_ad0.gpmc_ad0 */
+			AM33XX_IOPAD(0x804, PIN_INPUT_PULLUP | MUX_MODE0)	/* gpmc_ad1.gpmc_ad1 */
+			AM33XX_IOPAD(0x808, PIN_INPUT_PULLUP | MUX_MODE0)	/* gpmc_ad2.gpmc_ad2 */
+			AM33XX_IOPAD(0x80c, PIN_INPUT_PULLUP | MUX_MODE0)	/* gpmc_ad3.gpmc_ad3 */
+			AM33XX_IOPAD(0x810, PIN_INPUT_PULLUP | MUX_MODE0)	/* gpmc_ad4.gpmc_ad4 */
+			AM33XX_IOPAD(0x814, PIN_INPUT_PULLUP | MUX_MODE0)	/* gpmc_ad5.gpmc_ad5 */
+			AM33XX_IOPAD(0x818, PIN_INPUT_PULLUP | MUX_MODE0)	/* gpmc_ad6.gpmc_ad6 */
+			AM33XX_IOPAD(0x81c, PIN_INPUT_PULLUP | MUX_MODE0)	/* gpmc_ad7.gpmc_ad7 */
+			AM33XX_IOPAD(0x870, PIN_INPUT_PULLUP | MUX_MODE0)	/* gpmc_wait0.gpmc_wait0 */
+			AM33XX_IOPAD(0x874, PIN_INPUT_PULLUP | MUX_MODE7)	/* gpmc_wpn.gpio0_30 */
+			AM33XX_IOPAD(0x87c, PIN_OUTPUT | MUX_MODE0)		/* gpmc_csn0.gpmc_csn0 */
+			AM33XX_IOPAD(0x890, PIN_OUTPUT | MUX_MODE0)		/* gpmc_advn_ale.gpmc_advn_ale */
+			AM33XX_IOPAD(0x894, PIN_OUTPUT | MUX_MODE0)		/* gpmc_oen_ren.gpmc_oen_ren */
+			AM33XX_IOPAD(0x898, PIN_OUTPUT | MUX_MODE0)		/* gpmc_wen.gpmc_wen */
+			AM33XX_IOPAD(0x89c, PIN_OUTPUT | MUX_MODE0)		/* gpmc_be0n_cle.gpmc_be0n_cle */
 		>;
 	};
 
 	uart0_pins: pinmux_uart0_pins {
 		pinctrl-single,pins = <
-			0x170 (PIN_INPUT_PULLUP | MUX_MODE0)	/* uart0_rxd.uart0_rxd */
-			0x174 (PIN_OUTPUT_PULLDOWN | MUX_MODE0)	/* uart0_txd.uart0_txd */
+			AM33XX_IOPAD(0x970, PIN_INPUT_PULLUP | MUX_MODE0)	/* uart0_rxd.uart0_rxd */
+			AM33XX_IOPAD(0x974, PIN_OUTPUT_PULLDOWN | MUX_MODE0)	/* uart0_txd.uart0_txd */
 		>;
 	};
 
 	leds_pins: pinmux_leds_pins {
 		pinctrl-single,pins = <
-			0x5c (PIN_OUTPUT_PULLDOWN | MUX_MODE7)	/* gpmc_a7.gpio1_23 */
+			AM33XX_IOPAD(0x85c, PIN_OUTPUT_PULLDOWN | MUX_MODE7)	/* gpmc_a7.gpio1_23 */
 		>;
 	};
 };
diff --git a/arch/arm/boot/dts/am437x-gp-evm.dts b/arch/arm/boot/dts/am437x-gp-evm.dts
index b259d7c29bcd..d2450ab0a380 100644
--- a/arch/arm/boot/dts/am437x-gp-evm.dts
+++ b/arch/arm/boot/dts/am437x-gp-evm.dts
@@ -595,8 +595,17 @@
 
 		attb-gpio = <&gpio3 22 GPIO_ACTIVE_HIGH>;
 
+		/*
+		 * 0x264 represents the offset of padconf register of
+		 * gpio3_22 from am43xx_pinmux base.
+		 */
+		interrupts-extended = <&gpio3 22 IRQ_TYPE_NONE>,
+				      <&am43xx_pinmux 0x264>;
+		interrupt-names = "tsc", "wakeup";
+
 		touchscreen-size-x = <1024>;
 		touchscreen-size-y = <600>;
+		wakeup-source;
 	};
 
 	ov2659@30 {
diff --git a/arch/arm/boot/dts/dra72-evm.dts b/arch/arm/boot/dts/dra72-evm.dts
index 27e414295acc..d6104d5f0c01 100644
--- a/arch/arm/boot/dts/dra72-evm.dts
+++ b/arch/arm/boot/dts/dra72-evm.dts
@@ -429,12 +429,6 @@
 		interrupts = <11 IRQ_TYPE_EDGE_FALLING>;
 		interrupt-controller;
 		#interrupt-cells = <2>;
-
-		cpsw_sel_s0 {
-			gpio-hog;
-			gpios = <4 GPIO_ACTIVE_HIGH>;
-			output-low;
-		};
 	};
 
 	tlv320aic3106: tlv320aic3106@19 {
@@ -689,6 +683,7 @@
 	pinctrl-0 = <&cpsw_default>;
 	pinctrl-1 = <&cpsw_sleep>;
 	slaves = <1>;
+	mode-gpios = <&pcf_gpio_21 4 GPIO_ACTIVE_HIGH>;
 };
 
 &cpsw_emac0 {
diff --git a/arch/arm/boot/dts/omap3-igep.dtsi b/arch/arm/boot/dts/omap3-igep.dtsi
index 09a438ebfbbe..3caf062f882c 100644
--- a/arch/arm/boot/dts/omap3-igep.dtsi
+++ b/arch/arm/boot/dts/omap3-igep.dtsi
@@ -1,7 +1,7 @@
 /*
  * Common device tree for IGEP boards based on AM/DM37x
  *
- * Copyright (C) 2012 Javier Martinez Canillas <javier@collabora.co.uk>
+ * Copyright (C) 2012 Javier Martinez Canillas <javier@osg.samsung.com>
  * Copyright (C) 2012 Enric Balletbo i Serra <eballetbo@gmail.com>
  *
  * This program is free software; you can redistribute it and/or modify
diff --git a/arch/arm/boot/dts/omap3-igep0020-common.dtsi b/arch/arm/boot/dts/omap3-igep0020-common.dtsi
index 5ad688c57a00..d90f12c39307 100644
--- a/arch/arm/boot/dts/omap3-igep0020-common.dtsi
+++ b/arch/arm/boot/dts/omap3-igep0020-common.dtsi
@@ -1,7 +1,7 @@
 /*
  * Common Device Tree Source for IGEPv2
  *
- * Copyright (C) 2014 Javier Martinez Canillas <javier@collabora.co.uk>
+ * Copyright (C) 2014 Javier Martinez Canillas <javier@osg.samsung.com>
  * Copyright (C) 2014 Enric Balletbo i Serra <eballetbo@gmail.com>
  *
  * This program is free software; you can redistribute it and/or modify
@@ -111,40 +111,40 @@
 
 	tfp410_pins: pinmux_tfp410_pins {
 		pinctrl-single,pins = <
-			0x196 (PIN_OUTPUT | MUX_MODE4)   /* hdq_sio.gpio_170 */
+			OMAP3_CORE1_IOPAD(0x21c6, PIN_OUTPUT | MUX_MODE4)   /* hdq_sio.gpio_170 */
 		>;
 	};
 
 	dss_dpi_pins: pinmux_dss_dpi_pins {
 		pinctrl-single,pins = <
-			0x0a4 (PIN_OUTPUT | MUX_MODE0)   /* dss_pclk.dss_pclk */
-			0x0a6 (PIN_OUTPUT | MUX_MODE0)   /* dss_hsync.dss_hsync */
-			0x0a8 (PIN_OUTPUT | MUX_MODE0)   /* dss_vsync.dss_vsync */
-			0x0aa (PIN_OUTPUT | MUX_MODE0)   /* dss_acbias.dss_acbias */
-			0x0ac (PIN_OUTPUT | MUX_MODE0)   /* dss_data0.dss_data0 */
-			0x0ae (PIN_OUTPUT | MUX_MODE0)   /* dss_data1.dss_data1 */
-			0x0b0 (PIN_OUTPUT | MUX_MODE0)   /* dss_data2.dss_data2 */
-			0x0b2 (PIN_OUTPUT | MUX_MODE0)   /* dss_data3.dss_data3 */
-			0x0b4 (PIN_OUTPUT | MUX_MODE0)   /* dss_data4.dss_data4 */
-			0x0b6 (PIN_OUTPUT | MUX_MODE0)   /* dss_data5.dss_data5 */
-			0x0b8 (PIN_OUTPUT | MUX_MODE0)   /* dss_data6.dss_data6 */
-			0x0ba (PIN_OUTPUT | MUX_MODE0)   /* dss_data7.dss_data7 */
-			0x0bc (PIN_OUTPUT | MUX_MODE0)   /* dss_data8.dss_data8 */
-			0x0be (PIN_OUTPUT | MUX_MODE0)   /* dss_data9.dss_data9 */
-			0x0c0 (PIN_OUTPUT | MUX_MODE0)   /* dss_data10.dss_data10 */
-			0x0c2 (PIN_OUTPUT | MUX_MODE0)   /* dss_data11.dss_data11 */
-			0x0c4 (PIN_OUTPUT | MUX_MODE0)   /* dss_data12.dss_data12 */
-			0x0c6 (PIN_OUTPUT | MUX_MODE0)   /* dss_data13.dss_data13 */
-			0x0c8 (PIN_OUTPUT | MUX_MODE0)   /* dss_data14.dss_data14 */
-			0x0ca (PIN_OUTPUT | MUX_MODE0)   /* dss_data15.dss_data15 */
-			0x0cc (PIN_OUTPUT | MUX_MODE0)   /* dss_data16.dss_data16 */
-			0x0ce (PIN_OUTPUT | MUX_MODE0)   /* dss_data17.dss_data17 */
-			0x0d0 (PIN_OUTPUT | MUX_MODE0)   /* dss_data18.dss_data18 */
-			0x0d2 (PIN_OUTPUT | MUX_MODE0)   /* dss_data19.dss_data19 */
-			0x0d4 (PIN_OUTPUT | MUX_MODE0)   /* dss_data20.dss_data20 */
-			0x0d6 (PIN_OUTPUT | MUX_MODE0)   /* dss_data21.dss_data21 */
-			0x0d8 (PIN_OUTPUT | MUX_MODE0)   /* dss_data22.dss_data22 */
-			0x0da (PIN_OUTPUT | MUX_MODE0)   /* dss_data23.dss_data23 */
+			OMAP3_CORE1_IOPAD(0x20d4, PIN_OUTPUT | MUX_MODE0)   /* dss_pclk.dss_pclk */
+			OMAP3_CORE1_IOPAD(0x20d6, PIN_OUTPUT | MUX_MODE0)   /* dss_hsync.dss_hsync */
+			OMAP3_CORE1_IOPAD(0x20d8, PIN_OUTPUT | MUX_MODE0)   /* dss_vsync.dss_vsync */
+			OMAP3_CORE1_IOPAD(0x20da, PIN_OUTPUT | MUX_MODE0)   /* dss_acbias.dss_acbias */
+			OMAP3_CORE1_IOPAD(0x20dc, PIN_OUTPUT | MUX_MODE0)   /* dss_data0.dss_data0 */
+			OMAP3_CORE1_IOPAD(0x20de, PIN_OUTPUT | MUX_MODE0)   /* dss_data1.dss_data1 */
+			OMAP3_CORE1_IOPAD(0x20e0, PIN_OUTPUT | MUX_MODE0)   /* dss_data2.dss_data2 */
+			OMAP3_CORE1_IOPAD(0x20e2, PIN_OUTPUT | MUX_MODE0)   /* dss_data3.dss_data3 */
+			OMAP3_CORE1_IOPAD(0x20e4, PIN_OUTPUT | MUX_MODE0)   /* dss_data4.dss_data4 */
+			OMAP3_CORE1_IOPAD(0x20e6, PIN_OUTPUT | MUX_MODE0)   /* dss_data5.dss_data5 */
+			OMAP3_CORE1_IOPAD(0x20e8, PIN_OUTPUT | MUX_MODE0)   /* dss_data6.dss_data6 */
+			OMAP3_CORE1_IOPAD(0x20ea, PIN_OUTPUT | MUX_MODE0)   /* dss_data7.dss_data7 */
+			OMAP3_CORE1_IOPAD(0x20ec, PIN_OUTPUT | MUX_MODE0)   /* dss_data8.dss_data8 */
+			OMAP3_CORE1_IOPAD(0x20ee, PIN_OUTPUT | MUX_MODE0)   /* dss_data9.dss_data9 */
+			OMAP3_CORE1_IOPAD(0x20f0, PIN_OUTPUT | MUX_MODE0)   /* dss_data10.dss_data10 */
+			OMAP3_CORE1_IOPAD(0x20f2, PIN_OUTPUT | MUX_MODE0)   /* dss_data11.dss_data11 */
+			OMAP3_CORE1_IOPAD(0x20f4, PIN_OUTPUT | MUX_MODE0)   /* dss_data12.dss_data12 */
+			OMAP3_CORE1_IOPAD(0x20f6, PIN_OUTPUT | MUX_MODE0)   /* dss_data13.dss_data13 */
+			OMAP3_CORE1_IOPAD(0x20f8, PIN_OUTPUT | MUX_MODE0)   /* dss_data14.dss_data14 */
+			OMAP3_CORE1_IOPAD(0x20fa, PIN_OUTPUT | MUX_MODE0)   /* dss_data15.dss_data15 */
+			OMAP3_CORE1_IOPAD(0x20fc, PIN_OUTPUT | MUX_MODE0)   /* dss_data16.dss_data16 */
+			OMAP3_CORE1_IOPAD(0x20fe, PIN_OUTPUT | MUX_MODE0)   /* dss_data17.dss_data17 */
+			OMAP3_CORE1_IOPAD(0x2100, PIN_OUTPUT | MUX_MODE0)   /* dss_data18.dss_data18 */
+			OMAP3_CORE1_IOPAD(0x2102, PIN_OUTPUT | MUX_MODE0)   /* dss_data19.dss_data19 */
+			OMAP3_CORE1_IOPAD(0x2104, PIN_OUTPUT | MUX_MODE0)   /* dss_data20.dss_data20 */
+			OMAP3_CORE1_IOPAD(0x2106, PIN_OUTPUT | MUX_MODE0)   /* dss_data21.dss_data21 */
+			OMAP3_CORE1_IOPAD(0x2108, PIN_OUTPUT | MUX_MODE0)   /* dss_data22.dss_data22 */
+			OMAP3_CORE1_IOPAD(0x210a, PIN_OUTPUT | MUX_MODE0)   /* dss_data23.dss_data23 */
 		>;
 	};
 
diff --git a/arch/arm/boot/dts/omap3-igep0020-rev-f.dts b/arch/arm/boot/dts/omap3-igep0020-rev-f.dts
index 72f7cdc091fb..321c2b7a4e9f 100644
--- a/arch/arm/boot/dts/omap3-igep0020-rev-f.dts
+++ b/arch/arm/boot/dts/omap3-igep0020-rev-f.dts
@@ -1,7 +1,7 @@
 /*
  * Device Tree Source for IGEPv2 Rev. F (TI OMAP AM/DM37x)
  *
- * Copyright (C) 2012 Javier Martinez Canillas <javier@collabora.co.uk>
+ * Copyright (C) 2012 Javier Martinez Canillas <javier@osg.samsung.com>
  * Copyright (C) 2012 Enric Balletbo i Serra <eballetbo@gmail.com>
  *
  * This program is free software; you can redistribute it and/or modify
diff --git a/arch/arm/boot/dts/omap3-igep0020.dts b/arch/arm/boot/dts/omap3-igep0020.dts
index 5683b8bf3475..3835e1569c29 100644
--- a/arch/arm/boot/dts/omap3-igep0020.dts
+++ b/arch/arm/boot/dts/omap3-igep0020.dts
@@ -1,7 +1,7 @@
 /*
  * Device Tree Source for IGEPv2 Rev. C (TI OMAP AM/DM37x)
  *
- * Copyright (C) 2012 Javier Martinez Canillas <javier@collabora.co.uk>
+ * Copyright (C) 2012 Javier Martinez Canillas <javier@osg.samsung.com>
  * Copyright (C) 2012 Enric Balletbo i Serra <eballetbo@gmail.com>
  *
  * This program is free software; you can redistribute it and/or modify
diff --git a/arch/arm/boot/dts/omap3-igep0030-common.dtsi b/arch/arm/boot/dts/omap3-igep0030-common.dtsi
index 0cb1527c39d4..640f06603966 100644
--- a/arch/arm/boot/dts/omap3-igep0030-common.dtsi
+++ b/arch/arm/boot/dts/omap3-igep0030-common.dtsi
@@ -1,7 +1,7 @@
 /*
  * Common Device Tree Source for IGEP COM MODULE
  *
- * Copyright (C) 2014 Javier Martinez Canillas <javier@collabora.co.uk>
+ * Copyright (C) 2014 Javier Martinez Canillas <javier@osg.samsung.com>
  * Copyright (C) 2014 Enric Balletbo i Serra <eballetbo@gmail.com>
  *
  * This program is free software; you can redistribute it and/or modify
diff --git a/arch/arm/boot/dts/omap3-igep0030-rev-g.dts b/arch/arm/boot/dts/omap3-igep0030-rev-g.dts
index b899e341874a..76dc08868bfb 100644
--- a/arch/arm/boot/dts/omap3-igep0030-rev-g.dts
+++ b/arch/arm/boot/dts/omap3-igep0030-rev-g.dts
@@ -1,7 +1,7 @@
 /*
  * Device Tree Source for IGEP COM MODULE Rev. G (TI OMAP AM/DM37x)
  *
- * Copyright (C) 2014 Javier Martinez Canillas <javier@collabora.co.uk>
+ * Copyright (C) 2014 Javier Martinez Canillas <javier@osg.samsung.com>
  * Copyright (C) 2014 Enric Balletbo i Serra <eballetbo@gmail.com>
  *
  * This program is free software; you can redistribute it and/or modify
diff --git a/arch/arm/boot/dts/omap3-igep0030.dts b/arch/arm/boot/dts/omap3-igep0030.dts
index 8150f47ccdf5..468608dab30a 100644
--- a/arch/arm/boot/dts/omap3-igep0030.dts
+++ b/arch/arm/boot/dts/omap3-igep0030.dts
@@ -1,7 +1,7 @@
 /*
  * Device Tree Source for IGEP COM MODULE Rev. E (TI OMAP AM/DM37x)
  *
- * Copyright (C) 2012 Javier Martinez Canillas <javier@collabora.co.uk>
+ * Copyright (C) 2012 Javier Martinez Canillas <javier@osg.samsung.com>
  * Copyright (C) 2012 Enric Balletbo i Serra <eballetbo@gmail.com>
  *
  * This program is free software; you can redistribute it and/or modify
diff --git a/arch/arm/boot/dts/omap5-board-common.dtsi b/arch/arm/boot/dts/omap5-board-common.dtsi
new file mode 100644
index 000000000000..5cf76a1c5c75
--- /dev/null
+++ b/arch/arm/boot/dts/omap5-board-common.dtsi
@@ -0,0 +1,655 @@
+/*
+ * Copyright (C) 2013 Texas Instruments Incorporated - http://www.ti.com/
+ *
+ * This program is free software; you can redistribute it and/or modify
+ * it under the terms of the GNU General Public License version 2 as
+ * published by the Free Software Foundation.
+ */
+#include "omap5.dtsi"
+#include <dt-bindings/interrupt-controller/irq.h>
+#include <dt-bindings/interrupt-controller/arm-gic.h>
+
+/ {
+	aliases {
+		display0 = &hdmi0;
+	};
+
+	vmmcsd_fixed: fixedregulator-mmcsd {
+		compatible = "regulator-fixed";
+		regulator-name = "vmmcsd_fixed";
+		regulator-min-microvolt = <3000000>;
+		regulator-max-microvolt = <3000000>;
+	};
+
+	mmc3_pwrseq: sdhci0_pwrseq {
+		compatible = "mmc-pwrseq-simple";
+		clocks = <&clk32kgaudio>;
+		clock-names = "ext_clock";
+	};
+
+	vmmcsdio_fixed: fixedregulator-mmcsdio {
+		compatible = "regulator-fixed";
+		regulator-name = "vmmcsdio_fixed";
+		regulator-min-microvolt = <1800000>;
+		regulator-max-microvolt = <1800000>;
+		gpio = <&gpio5 12 GPIO_ACTIVE_HIGH>;	/* gpio140 WLAN_EN */
+		enable-active-high;
+		startup-delay-us = <70000>;
+		pinctrl-names = "default";
+		pinctrl-0 = <&wlan_pins>;
+	};
+
+	/* HS USB Host PHY on PORT 2 */
+	hsusb2_phy: hsusb2_phy {
+		compatible = "usb-nop-xceiv";
+		reset-gpios = <&gpio3 16 GPIO_ACTIVE_LOW>; /* gpio3_80 HUB_NRESET */
+		clocks = <&auxclk1_ck>;
+		clock-names = "main_clk";
+		clock-frequency = <19200000>;
+	};
+
+	/* HS USB Host PHY on PORT 3 */
+	hsusb3_phy: hsusb3_phy {
+		compatible = "usb-nop-xceiv";
+		reset-gpios = <&gpio3 15 GPIO_ACTIVE_LOW>; /* gpio3_79 ETH_NRESET */
+	};
+
+	leds {
+		compatible = "gpio-leds";
+		led@1 {
+			label = "omap5:blue:usr1";
+			gpios = <&gpio5 25 GPIO_ACTIVE_HIGH>; /* gpio5_153 D1 LED */
+			linux,default-trigger = "heartbeat";
+			default-state = "off";
+		};
+	};
+
+	tpd12s015: encoder@0 {
+		compatible = "ti,tpd12s015";
+
+		pinctrl-names = "default";
+		pinctrl-0 = <&tpd12s015_pins>;
+
+		/* gpios defined in the board specific dts */
+
+		ports {
+			#address-cells = <1>;
+			#size-cells = <0>;
+
+			port@0 {
+				reg = <0>;
+
+				tpd12s015_in: endpoint@0 {
+					remote-endpoint = <&hdmi_out>;
+				};
+			};
+
+			port@1 {
+				reg = <1>;
+
+				tpd12s015_out: endpoint@0 {
+					remote-endpoint = <&hdmi_connector_in>;
+				};
+			};
+		};
+	};
+
+	hdmi0: connector@0 {
+		compatible = "hdmi-connector";
+		label = "hdmi";
+
+		type = "b";
+
+		port {
+			hdmi_connector_in: endpoint {
+				remote-endpoint = <&tpd12s015_out>;
+			};
+		};
+	};
+
+	sound: sound {
+		compatible = "ti,abe-twl6040";
+		ti,model = "omap5-uevm";
+
+		ti,mclk-freq = <19200000>;
+
+		ti,mcpdm = <&mcpdm>;
+
+		ti,twl6040 = <&twl6040>;
+
+		/* Audio routing */
+		ti,audio-routing =
+			"Headset Stereophone", "HSOL",
+			"Headset Stereophone", "HSOR",
+			"Line Out", "AUXL",
+			"Line Out", "AUXR",
+			"HSMIC", "Headset Mic",
+			"Headset Mic", "Headset Mic Bias",
+			"AFML", "Line In",
+			"AFMR", "Line In";
+	};
+};
+
+&omap5_pmx_core {
+	pinctrl-names = "default";
+	pinctrl-0 = <
+			&usbhost_pins
+			&led_gpio_pins
+	>;
+
+	twl6040_pins: pinmux_twl6040_pins {
+		pinctrl-single,pins = <
+			0x17e (PIN_OUTPUT | MUX_MODE6)	/* mcspi1_somi.gpio5_141 */
+		>;
+	};
+
+	mcpdm_pins: pinmux_mcpdm_pins {
+		pinctrl-single,pins = <
+			0x142 (PIN_INPUT_PULLDOWN | MUX_MODE0)	/* abe_clks.abe_clks */
+			0x15c (PIN_INPUT_PULLDOWN | MUX_MODE0)	/* abemcpdm_ul_data.abemcpdm_ul_data */
+			0x15e (PIN_INPUT_PULLDOWN | MUX_MODE0)	/* abemcpdm_dl_data.abemcpdm_dl_data */
+			0x160 (PIN_INPUT_PULLUP | MUX_MODE0)	/* abemcpdm_frame.abemcpdm_frame */
+			0x162 (PIN_INPUT_PULLDOWN | MUX_MODE0)	/* abemcpdm_lb_clk.abemcpdm_lb_clk */
+		>;
+	};
+
+	mcbsp1_pins: pinmux_mcbsp1_pins {
+		pinctrl-single,pins = <
+			0x14c (PIN_INPUT | MUX_MODE1)		/* abedmic_clk2.abemcbsp1_fsx */
+			0x14e (PIN_OUTPUT_PULLDOWN | MUX_MODE1)	/* abedmic_clk3.abemcbsp1_dx */
+			0x150 (PIN_INPUT | MUX_MODE1)		/* abeslimbus1_clock.abemcbsp1_clkx */
+			0x152 (PIN_INPUT_PULLDOWN | MUX_MODE1)	/* abeslimbus1_data.abemcbsp1_dr */
+		>;
+	};
+
+	mcbsp2_pins: pinmux_mcbsp2_pins {
+		pinctrl-single,pins = <
+			0x154 (PIN_INPUT_PULLDOWN | MUX_MODE0)	/* abemcbsp2_dr.abemcbsp2_dr */
+			0x156 (PIN_OUTPUT_PULLDOWN | MUX_MODE0)	/* abemcbsp2_dx.abemcbsp2_dx */
+			0x158 (PIN_INPUT | MUX_MODE0)		/* abemcbsp2_fsx.abemcbsp2_fsx */
+			0x15a (PIN_INPUT | MUX_MODE0)		/* abemcbsp2_clkx.abemcbsp2_clkx */
+		>;
+	};
+
+	i2c1_pins: pinmux_i2c1_pins {
+		pinctrl-single,pins = <
+			0x1b2 (PIN_INPUT_PULLUP | MUX_MODE0)	/* i2c1_scl */
+			0x1b4 (PIN_INPUT_PULLUP | MUX_MODE0)	/* i2c1_sda */
+		>;
+	};
+
+	mcspi2_pins: pinmux_mcspi2_pins {
+		pinctrl-single,pins = <
+			0xbc (PIN_INPUT | MUX_MODE0)		/*  mcspi2_clk */
+			0xbe (PIN_INPUT | MUX_MODE0)		/*  mcspi2_simo */
+			0xc0 (PIN_INPUT_PULLUP | MUX_MODE0)	/*  mcspi2_somi */
+			0xc2 (PIN_OUTPUT | MUX_MODE0)		/*  mcspi2_cs0 */
+		>;
+	};
+
+	mcspi3_pins: pinmux_mcspi3_pins {
+		pinctrl-single,pins = <
+			0x78 (PIN_INPUT | MUX_MODE1)		/*  mcspi3_somi */
+			0x7a (PIN_INPUT | MUX_MODE1)		/*  mcspi3_cs0 */
+			0x7c (PIN_INPUT | MUX_MODE1)		/*  mcspi3_simo */
+			0x7e (PIN_INPUT | MUX_MODE1)		/*  mcspi3_clk */
+		>;
+	};
+
+	mmc3_pins: pinmux_mmc3_pins {
+		pinctrl-single,pins = <
+			OMAP5_IOPAD(0x01a4, PIN_INPUT_PULLUP | MUX_MODE0) /* wlsdio_clk */
+			OMAP5_IOPAD(0x01a6, PIN_INPUT_PULLUP | MUX_MODE0) /* wlsdio_cmd */
+			OMAP5_IOPAD(0x01a8, PIN_INPUT_PULLUP | MUX_MODE0) /* wlsdio_data0 */
+			OMAP5_IOPAD(0x01aa, PIN_INPUT_PULLUP | MUX_MODE0) /* wlsdio_data1 */
+			OMAP5_IOPAD(0x01ac, PIN_INPUT_PULLUP | MUX_MODE0) /* wlsdio_data2 */
+			OMAP5_IOPAD(0x01ae, PIN_INPUT_PULLUP | MUX_MODE0) /* wlsdio_data3 */
+		>;
+	};
+
+	wlan_pins: pinmux_wlan_pins {
+		pinctrl-single,pins = <
+			OMAP5_IOPAD(0x1bc, PIN_OUTPUT | MUX_MODE6) /* mcspi1_clk.gpio5_140 */
+		>;
+	};
+
+	usbhost_pins: pinmux_usbhost_pins {
+		pinctrl-single,pins = <
+			0x84 (PIN_INPUT | MUX_MODE0) /* usbb2_hsic_strobe */
+			0x86 (PIN_INPUT | MUX_MODE0) /* usbb2_hsic_data */
+
+			0x19e (PIN_INPUT | MUX_MODE0) /* usbb3_hsic_strobe */
+			0x1a0 (PIN_INPUT | MUX_MODE0) /* usbb3_hsic_data */
+
+			0x70 (PIN_OUTPUT | MUX_MODE6) /* gpio3_80 HUB_NRESET */
+			0x6e (PIN_OUTPUT | MUX_MODE6) /* gpio3_79 ETH_NRESET */
+		>;
+	};
+
+	led_gpio_pins: pinmux_led_gpio_pins {
+		pinctrl-single,pins = <
+			0x196 (PIN_OUTPUT | MUX_MODE6) /* uart3_cts_rctx.gpio5_153 */
+		>;
+	};
+
+	uart1_pins: pinmux_uart1_pins {
+		pinctrl-single,pins = <
+			0x60 (PIN_OUTPUT | MUX_MODE0) /* uart1_tx.uart1_cts */
+			0x62 (PIN_INPUT_PULLUP | MUX_MODE0) /* uart1_tx.uart1_cts */
+			0x64 (PIN_INPUT_PULLUP | MUX_MODE0) /* uart1_rx.uart1_rts */
+			0x66 (PIN_OUTPUT | MUX_MODE0) /* uart1_rx.uart1_rts */
+		>;
+	};
+
+	uart3_pins: pinmux_uart3_pins {
+		pinctrl-single,pins = <
+			0x19a (PIN_OUTPUT | MUX_MODE0) /* uart3_rts_irsd.uart3_tx_irtx */
+			0x19c (PIN_INPUT_PULLUP | MUX_MODE0) /* uart3_rx_irrx.uart3_usbb3_hsic */
+		>;
+	};
+
+	uart5_pins: pinmux_uart5_pins {
+		pinctrl-single,pins = <
+			0x170 (PIN_INPUT_PULLUP | MUX_MODE0) /* uart5_rx.uart5_rx */
+			0x172 (PIN_OUTPUT | MUX_MODE0) /* uart5_tx.uart5_tx */
+			0x174 (PIN_INPUT_PULLUP | MUX_MODE0) /* uart5_cts.uart5_rts */
+			0x176 (PIN_OUTPUT | MUX_MODE0) /* uart5_cts.uart5_rts */
+		>;
+	};
+
+	dss_hdmi_pins: pinmux_dss_hdmi_pins {
+		pinctrl-single,pins = <
+			0x0fc (PIN_INPUT_PULLUP | MUX_MODE0)	/* hdmi_cec.hdmi_cec */
+			0x100 (PIN_INPUT | MUX_MODE0)	/* hdmi_ddc_scl.hdmi_ddc_scl */
+			0x102 (PIN_INPUT | MUX_MODE0)	/* hdmi_ddc_sda.hdmi_ddc_sda */
+		>;
+	};
+
+	tpd12s015_pins: pinmux_tpd12s015_pins {
+		pinctrl-single,pins = <
+			0x0fe (PIN_INPUT_PULLDOWN | MUX_MODE6)	/* hdmi_hpd.gpio7_193 */
+		>;
+	};
+};
+
+&omap5_pmx_wkup {
+	pinctrl-names = "default";
+	pinctrl-0 = <
+			&usbhost_wkup_pins
+	>;
+
+	usbhost_wkup_pins: pinmux_usbhost_wkup_pins {
+		pinctrl-single,pins = <
+			0x1A (PIN_OUTPUT | MUX_MODE0) /* fref_clk1_out, USB hub clk */
+		>;
+	};
+
+	wlcore_irq_pin: pinmux_wlcore_irq_pin {
+		pinctrl-single,pins = <
+			OMAP5_IOPAD(0x040, WAKEUP_EN | PIN_INPUT_PULLUP | MUX_MODE6)	/* llia_wakereqin.gpio1_wk14 */
+		>;
+	};
+};
+
+&mmc1 {
+	vmmc-supply = <&ldo9_reg>;
+	bus-width = <4>;
+};
+
+&mmc2 {
+	vmmc-supply = <&vmmcsd_fixed>;
+	bus-width = <8>;
+	ti,non-removable;
+};
+
+&mmc3 {
+	vmmc-supply = <&vmmcsdio_fixed>;
+	mmc-pwrseq = <&mmc3_pwrseq>;
+	bus-width = <4>;
+	non-removable;
+	cap-power-off-card;
+	pinctrl-names = "default";
+	pinctrl-0 = <&mmc3_pins &wlcore_irq_pin>;
+	interrupts-extended = <&gic GIC_SPI 94 IRQ_TYPE_LEVEL_HIGH
+			       &omap5_pmx_core 0x168>;
+
+	#address-cells = <1>;
+	#size-cells = <0>;
+	wlcore: wlcore@2 {
+		compatible = "ti,wl1271";
+		reg = <2>;
+		interrupt-parent = <&gpio1>;
+		interrupts = <14 IRQ_TYPE_LEVEL_HIGH>;	/* gpio 14 */
+		ref-clock-frequency = <26000000>;
+	};
+};
+
+&mmc4 {
+	status = "disabled";
+};
+
+&mmc5 {
+	status = "disabled";
+};
+
+&i2c1 {
+	pinctrl-names = "default";
+	pinctrl-0 = <&i2c1_pins>;
+
+	clock-frequency = <400000>;
+
+	palmas: palmas@48 {
+		compatible = "ti,palmas";
+		interrupts = <GIC_SPI 7 IRQ_TYPE_NONE>; /* IRQ_SYS_1N */
+		reg = <0x48>;
+		interrupt-controller;
+		#interrupt-cells = <2>;
+		ti,system-power-controller;
+
+		extcon_usb3: palmas_usb {
+			compatible = "ti,palmas-usb-vid";
+			ti,enable-vbus-detection;
+			ti,enable-id-detection;
+			ti,wakeup;
+		};
+
+		clk32kgaudio: palmas_clk32k@1 {
+			compatible = "ti,palmas-clk32kgaudio";
+			#clock-cells = <0>;
+		};
+
+		palmas_pmic {
+			compatible = "ti,palmas-pmic";
+			interrupt-parent = <&palmas>;
+			interrupts = <14 IRQ_TYPE_NONE>;
+			interrupt-name = "short-irq";
+
+			ti,ldo6-vibrator;
+
+			regulators {
+				smps123_reg: smps123 {
+					/* VDD_OPP_MPU */
+					regulator-name = "smps123";
+					regulator-min-microvolt = < 600000>;
+					regulator-max-microvolt = <1500000>;
+					regulator-always-on;
+					regulator-boot-on;
+				};
+
+				smps45_reg: smps45 {
+					/* VDD_OPP_MM */
+					regulator-name = "smps45";
+					regulator-min-microvolt = < 600000>;
+					regulator-max-microvolt = <1310000>;
+					regulator-always-on;
+					regulator-boot-on;
+				};
+
+				smps6_reg: smps6 {
+					/* VDD_DDR3 - over VDD_SMPS6 */
+					regulator-name = "smps6";
+					regulator-min-microvolt = <1200000>;
+					regulator-max-microvolt = <1200000>;
+					regulator-always-on;
+					regulator-boot-on;
+				};
+
+				smps7_reg: smps7 {
+					/* VDDS_1v8_OMAP over VDDS_1v8_MAIN */
+					regulator-name = "smps7";
+					regulator-min-microvolt = <1800000>;
+					regulator-max-microvolt = <1800000>;
+					regulator-always-on;
+					regulator-boot-on;
+				};
+
+				smps8_reg: smps8 {
+					/* VDD_OPP_CORE */
+					regulator-name = "smps8";
+					regulator-min-microvolt = < 600000>;
+					regulator-max-microvolt = <1310000>;
+					regulator-always-on;
+					regulator-boot-on;
+				};
+
+				smps9_reg: smps9 {
+					/* VDDA_2v1_AUD over VDD_2v1 */
+					regulator-name = "smps9";
+					regulator-min-microvolt = <2100000>;
+					regulator-max-microvolt = <2100000>;
+					ti,smps-range = <0x80>;
+				};
+
+				smps10_out2_reg: smps10_out2 {
+					/* VBUS_5V_OTG */
+					regulator-name = "smps10_out2";
+					regulator-min-microvolt = <5000000>;
+					regulator-max-microvolt = <5000000>;
+					regulator-always-on;
+					regulator-boot-on;
+				};
+
+				smps10_out1_reg: smps10_out1 {
+					/* VBUS_5V_OTG */
+					regulator-name = "smps10_out1";
+					regulator-min-microvolt = <5000000>;
+					regulator-max-microvolt = <5000000>;
+				};
+
+				ldo1_reg: ldo1 {
+					/* VDDAPHY_CAM: vdda_csiport */
+					regulator-name = "ldo1";
+					regulator-min-microvolt = <1500000>;
+					regulator-max-microvolt = <1800000>;
+				};
+
+				ldo2_reg: ldo2 {
+					/* VCC_2V8_DISP: Does not go anywhere */
+					regulator-name = "ldo2";
+					regulator-min-microvolt = <2800000>;
+					regulator-max-microvolt = <2800000>;
+					/* Unused */
+					status = "disabled";
+				};
+
+				ldo3_reg: ldo3 {
+					/* VDDAPHY_MDM: vdda_lli */
+					regulator-name = "ldo3";
+					regulator-min-microvolt = <1500000>;
+					regulator-max-microvolt = <1500000>;
+					regulator-boot-on;
+					/* Only if Modem is used */
+					status = "disabled";
+				};
+
+				ldo4_reg: ldo4 {
+					/* VDDAPHY_DISP: vdda_dsiport/hdmi */
+					regulator-name = "ldo4";
+					regulator-min-microvolt = <1500000>;
+					regulator-max-microvolt = <1800000>;
+				};
+
+				ldo5_reg: ldo5 {
+					/* VDDA_1V8_PHY: usb/sata/hdmi.. */
+					regulator-name = "ldo5";
+					regulator-min-microvolt = <1800000>;
+					regulator-max-microvolt = <1800000>;
+					regulator-always-on;
+					regulator-boot-on;
+				};
+
+				ldo6_reg: ldo6 {
+					/* VDDS_1V2_WKUP: hsic/ldo_emu_wkup */
+					regulator-name = "ldo6";
+					regulator-min-microvolt = <1200000>;
+					regulator-max-microvolt = <1200000>;
+					regulator-always-on;
+					regulator-boot-on;
+				};
+
+				ldo7_reg: ldo7 {
+					/* VDD_VPP: vpp1 */
+					regulator-name = "ldo7";
+					regulator-min-microvolt = <2000000>;
+					regulator-max-microvolt = <2000000>;
+					/* Only for efuse reprograming! */
+					status = "disabled";
+				};
+
+				ldo8_reg: ldo8 {
+					/* VDD_3v0: Does not go anywhere */
+					regulator-name = "ldo8";
+					regulator-min-microvolt = <3000000>;
+					regulator-max-microvolt = <3000000>;
+					regulator-boot-on;
+					/* Unused */
+					status = "disabled";
+				};
+
+				ldo9_reg: ldo9 {
+					/* VCC_DV_SDIO: vdds_sdcard */
+					regulator-name = "ldo9";
+					regulator-min-microvolt = <1800000>;
+					regulator-max-microvolt = <3000000>;
+					regulator-boot-on;
+				};
+
+				ldoln_reg: ldoln {
+					/* VDDA_1v8_REF: vdds_osc/mm_l4per.. */
+					regulator-name = "ldoln";
+					regulator-min-microvolt = <1800000>;
+					regulator-max-microvolt = <1800000>;
+					regulator-always-on;
+					regulator-boot-on;
+				};
+
+				ldousb_reg: ldousb {
+					/* VDDA_3V_USB: VDDA_USBHS33 */
+					regulator-name = "ldousb";
+					regulator-min-microvolt = <3250000>;
+					regulator-max-microvolt = <3250000>;
+					regulator-always-on;
+					regulator-boot-on;
+				};
+
+				regen3_reg: regen3 {
+					/* REGEN3 controls LDO9 supply to card */
+					regulator-name = "regen3";
+					regulator-always-on;
+					regulator-boot-on;
+				};
+			};
+		};
+
+		palmas_power_button: palmas_power_button {
+			compatible = "ti,palmas-pwrbutton";
+			interrupt-parent = <&palmas>;
+			interrupts = <1 IRQ_TYPE_EDGE_FALLING>;
+			wakeup-source;
+		};
+	};
+
+	twl6040: twl@4b {
+		compatible = "ti,twl6040";
+		reg = <0x4b>;
+
+		pinctrl-names = "default";
+		pinctrl-0 = <&twl6040_pins>;
+
+		interrupts = <GIC_SPI 119 IRQ_TYPE_NONE>; /* IRQ_SYS_2N cascaded to gic */
+		ti,audpwron-gpio = <&gpio5 13 GPIO_ACTIVE_HIGH>;  /* gpio line 141 */
+
+		vio-supply = <&smps7_reg>;
+		v2v1-supply = <&smps9_reg>;
+		enable-active-high;
+
+		clocks = <&clk32kgaudio>;
+		clock-names = "clk32k";
+	};
+};
+
+&mcpdm {
+	pinctrl-names = "default";
+	pinctrl-0 = <&mcpdm_pins>;
+	status = "okay";
+};
+
+&mcbsp1 {
+	pinctrl-names = "default";
+	pinctrl-0 = <&mcbsp1_pins>;
+	status = "okay";
+};
+
+&mcbsp2 {
+	pinctrl-names = "default";
+	pinctrl-0 = <&mcbsp2_pins>;
+	status = "okay";
+};
+
+&usbhshost {
+	port2-mode = "ehci-hsic";
+	port3-mode = "ehci-hsic";
+};
+
+&usbhsehci {
+	phys = <0 &hsusb2_phy &hsusb3_phy>;
+};
+
+&usb3 {
+	extcon = <&extcon_usb3>;
+	vbus-supply = <&smps10_out1_reg>;
+};
+
+&mcspi1 {
+
+};
+
+&mcspi2 {
+	pinctrl-names = "default";
+	pinctrl-0 = <&mcspi2_pins>;
+};
+
+&mcspi3 {
+	pinctrl-names = "default";
+	pinctrl-0 = <&mcspi3_pins>;
+};
+
+&uart1 {
+	pinctrl-names = "default";
+	pinctrl-0 = <&uart1_pins>;
+};
+
+&uart3 {
+	pinctrl-names = "default";
+	pinctrl-0 = <&uart3_pins>;
+	interrupts-extended = <&wakeupgen GIC_SPI 74 IRQ_TYPE_LEVEL_HIGH>,
+			      <&omap5_pmx_core 0x19c>;
+};
+
+&uart5 {
+	pinctrl-names = "default";
+	pinctrl-0 = <&uart5_pins>;
+};
+
+&cpu0 {
+	cpu0-supply = <&smps123_reg>;
+};
+
+&dss {
+	status = "ok";
+};
+
+&hdmi {
+	status = "ok";
+
+	/* vdda-supply populated in board specific dts file */
+
+	pinctrl-names = "default";
+	pinctrl-0 = <&dss_hdmi_pins>;
+
+	port {
+		hdmi_out: endpoint {
+			remote-endpoint = <&tpd12s015_in>;
+		};
+	};
+};
diff --git a/arch/arm/boot/dts/omap5-igep0050.dts b/arch/arm/boot/dts/omap5-igep0050.dts
new file mode 100644
index 000000000000..46ecb1dd3b5c
--- /dev/null
+++ b/arch/arm/boot/dts/omap5-igep0050.dts
@@ -0,0 +1,54 @@
+/*
+ * Copyright (C) 2013 ISEE 2007 SL - http://www.isee.biz/
+ *
+ * This program is free software; you can redistribute it and/or modify
+ * it under the terms of the GNU General Public License version 2 as
+ * published by the Free Software Foundation.
+ */
+/dts-v1/;
+
+#include "omap5-board-common.dtsi"
+
+/ {
+	model = "IGEPv5";
+	compatible = "isee,omap5-igep0050", "ti,omap5";
+
+	memory {
+		device_type = "memory";
+		reg = <0x80000000 0x7f000000>; /* 2032 MB */
+	};
+};
+
+&hdmi {
+	vdda-supply = <&ldo7_reg>;
+};
+
+&i2c4 {
+	pinctrl-names = "default";
+	pinctrl-0 = <&i2c4_pins>;
+
+	tca6416: tca6416@21 {
+		compatible = "ti,tca6416";
+		reg = <0x21>;
+		gpio-controller;
+		#gpio-cells = <2>;
+	};
+};
+
+&omap5_pmx_core {
+	i2c4_pins: pinmux_i2c4_pins {
+		pinctrl-single,pins = <
+			OMAP5_IOPAD(0x0f8, PIN_INPUT | MUX_MODE0)	/* i2c4_scl */
+			OMAP5_IOPAD(0x0fa, PIN_INPUT | MUX_MODE0)	/* i2c4_sda */
+		>;
+	};
+};
+
+&tpd12s015 {
+	gpios = <&tca6416 11 0>,	/* TCA6416 P01, CT_CP_HDP */
+		<&tca6416 12 0>,	/* TCA6416 P00, LS_OE*/
+		<&gpio7 1 0>,		/* 193, HPD */
+		<&gpio7 2 0>,		/* 194, SCL */
+		<&gpio7 3 0>;		/* 195, SDA */
+};
+
diff --git a/arch/arm/boot/dts/omap5-uevm.dts b/arch/arm/boot/dts/omap5-uevm.dts
index 4da9e52f147b..05b1c1ebded8 100644
--- a/arch/arm/boot/dts/omap5-uevm.dts
+++ b/arch/arm/boot/dts/omap5-uevm.dts
@@ -7,9 +7,7 @@
  */
 /dts-v1/;
 
-#include "omap5.dtsi"
-#include <dt-bindings/interrupt-controller/irq.h>
-#include <dt-bindings/interrupt-controller/arm-gic.h>
+#include "omap5-board-common.dtsi"
 
 / {
 	model = "TI OMAP5 uEVM board";
@@ -19,523 +17,10 @@
 		device_type = "memory";
 		reg = <0x80000000 0x7F000000>; /* 2032 MB */
 	};
-
-	aliases {
-		display0 = &hdmi0;
-	};
-
-	vmmcsd_fixed: fixedregulator-mmcsd {
-		compatible = "regulator-fixed";
-		regulator-name = "vmmcsd_fixed";
-		regulator-min-microvolt = <3000000>;
-		regulator-max-microvolt = <3000000>;
-	};
-
-	/* HS USB Host PHY on PORT 2 */
-	hsusb2_phy: hsusb2_phy {
-		compatible = "usb-nop-xceiv";
-		reset-gpios = <&gpio3 16 GPIO_ACTIVE_LOW>; /* gpio3_80 HUB_NRESET */
-		clocks = <&auxclk1_ck>;
-		clock-names = "main_clk";
-		clock-frequency = <19200000>;
-	};
-
-	/* HS USB Host PHY on PORT 3 */
-	hsusb3_phy: hsusb3_phy {
-		compatible = "usb-nop-xceiv";
-		reset-gpios = <&gpio3 15 GPIO_ACTIVE_LOW>; /* gpio3_79 ETH_NRESET */
-	};
-
-	leds {
-		compatible = "gpio-leds";
-		led@1 {
-			label = "omap5:blue:usr1";
-			gpios = <&gpio5 25 GPIO_ACTIVE_HIGH>; /* gpio5_153 D1 LED */
-			linux,default-trigger = "heartbeat";
-			default-state = "off";
-		};
-	};
-
-	tpd12s015: encoder@0 {
-		compatible = "ti,tpd12s015";
-
-		pinctrl-names = "default";
-		pinctrl-0 = <&tpd12s015_pins>;
-
-		gpios = <&gpio9 0 GPIO_ACTIVE_HIGH>,	/* TCA6424A P01, CT CP HPD */
-			<&gpio9 1 GPIO_ACTIVE_HIGH>,	/* TCA6424A P00, LS OE */
-			<&gpio7 1 GPIO_ACTIVE_HIGH>;	/* GPIO 193, HPD */
-
-		ports {
-			#address-cells = <1>;
-			#size-cells = <0>;
-
-			port@0 {
-				reg = <0>;
-
-				tpd12s015_in: endpoint@0 {
-					remote-endpoint = <&hdmi_out>;
-				};
-			};
-
-			port@1 {
-				reg = <1>;
-
-				tpd12s015_out: endpoint@0 {
-					remote-endpoint = <&hdmi_connector_in>;
-				};
-			};
-		};
-	};
-
-	hdmi0: connector@0 {
-		compatible = "hdmi-connector";
-		label = "hdmi";
-
-		type = "b";
-
-		port {
-			hdmi_connector_in: endpoint {
-				remote-endpoint = <&tpd12s015_out>;
-			};
-		};
-	};
-
-	sound: sound {
-		compatible = "ti,abe-twl6040";
-		ti,model = "omap5-uevm";
-
-		ti,mclk-freq = <19200000>;
-
-		ti,mcpdm = <&mcpdm>;
-
-		ti,twl6040 = <&twl6040>;
-
-		/* Audio routing */
-		ti,audio-routing =
-			"Headset Stereophone", "HSOL",
-			"Headset Stereophone", "HSOR",
-			"Line Out", "AUXL",
-			"Line Out", "AUXR",
-			"HSMIC", "Headset Mic",
-			"Headset Mic", "Headset Mic Bias",
-			"AFML", "Line In",
-			"AFMR", "Line In";
-	};
-};
-
-&omap5_pmx_core {
-	pinctrl-names = "default";
-	pinctrl-0 = <
-			&usbhost_pins
-			&led_gpio_pins
-	>;
-
-	twl6040_pins: pinmux_twl6040_pins {
-		pinctrl-single,pins = <
-			0x17e (PIN_OUTPUT | MUX_MODE6)	/* mcspi1_somi.gpio5_141 */
-		>;
-	};
-
-	mcpdm_pins: pinmux_mcpdm_pins {
-		pinctrl-single,pins = <
-			0x142 (PIN_INPUT_PULLDOWN | MUX_MODE0)	/* abe_clks.abe_clks */
-			0x15c (PIN_INPUT_PULLDOWN | MUX_MODE0)	/* abemcpdm_ul_data.abemcpdm_ul_data */
-			0x15e (PIN_INPUT_PULLDOWN | MUX_MODE0)	/* abemcpdm_dl_data.abemcpdm_dl_data */
-			0x160 (PIN_INPUT_PULLUP | MUX_MODE0)	/* abemcpdm_frame.abemcpdm_frame */
-			0x162 (PIN_INPUT_PULLDOWN | MUX_MODE0)	/* abemcpdm_lb_clk.abemcpdm_lb_clk */
-		>;
-	};
-
-	mcbsp1_pins: pinmux_mcbsp1_pins {
-		pinctrl-single,pins = <
-			0x14c (PIN_INPUT | MUX_MODE1)		/* abedmic_clk2.abemcbsp1_fsx */
-			0x14e (PIN_OUTPUT_PULLDOWN | MUX_MODE1)	/* abedmic_clk3.abemcbsp1_dx */
-			0x150 (PIN_INPUT | MUX_MODE1)		/* abeslimbus1_clock.abemcbsp1_clkx */
-			0x152 (PIN_INPUT_PULLDOWN | MUX_MODE1)	/* abeslimbus1_data.abemcbsp1_dr */
-		>;
-	};
-
-	mcbsp2_pins: pinmux_mcbsp2_pins {
-		pinctrl-single,pins = <
-			0x154 (PIN_INPUT_PULLDOWN | MUX_MODE0)	/* abemcbsp2_dr.abemcbsp2_dr */
-			0x156 (PIN_OUTPUT_PULLDOWN | MUX_MODE0)	/* abemcbsp2_dx.abemcbsp2_dx */
-			0x158 (PIN_INPUT | MUX_MODE0)		/* abemcbsp2_fsx.abemcbsp2_fsx */
-			0x15a (PIN_INPUT | MUX_MODE0)		/* abemcbsp2_clkx.abemcbsp2_clkx */
-		>;
-	};
-
-	i2c1_pins: pinmux_i2c1_pins {
-		pinctrl-single,pins = <
-			0x1b2 (PIN_INPUT_PULLUP | MUX_MODE0)	/* i2c1_scl */
-			0x1b4 (PIN_INPUT_PULLUP | MUX_MODE0)	/* i2c1_sda */
-		>;
-	};
-
-	i2c5_pins: pinmux_i2c5_pins {
-		pinctrl-single,pins = <
-			0x186 (PIN_INPUT | MUX_MODE0)		/* i2c5_scl */
-			0x188 (PIN_INPUT | MUX_MODE0)		/* i2c5_sda */
-		>;
-	};
-
-	mcspi2_pins: pinmux_mcspi2_pins {
-		pinctrl-single,pins = <
-			0xbc (PIN_INPUT | MUX_MODE0)		/*  mcspi2_clk */
-			0xbe (PIN_INPUT | MUX_MODE0)		/*  mcspi2_simo */
-			0xc0 (PIN_INPUT_PULLUP | MUX_MODE0)	/*  mcspi2_somi */
-			0xc2 (PIN_OUTPUT | MUX_MODE0)		/*  mcspi2_cs0 */
-		>;
-	};
-
-	mcspi3_pins: pinmux_mcspi3_pins {
-		pinctrl-single,pins = <
-			0x78 (PIN_INPUT | MUX_MODE1)		/*  mcspi3_somi */
-			0x7a (PIN_INPUT | MUX_MODE1)		/*  mcspi3_cs0 */
-			0x7c (PIN_INPUT | MUX_MODE1)		/*  mcspi3_simo */
-			0x7e (PIN_INPUT | MUX_MODE1)		/*  mcspi3_clk */
-		>;
-	};
-
-	mcspi4_pins: pinmux_mcspi4_pins {
-		pinctrl-single,pins = <
-			0x164 (PIN_INPUT | MUX_MODE1)		/*  mcspi4_clk */
-			0x168 (PIN_INPUT | MUX_MODE1)		/*  mcspi4_simo */
-			0x16a (PIN_INPUT | MUX_MODE1)		/*  mcspi4_somi */
-			0x16c (PIN_INPUT | MUX_MODE1)		/*  mcspi4_cs0 */
-		>;
-	};
-
-	usbhost_pins: pinmux_usbhost_pins {
-		pinctrl-single,pins = <
-			0x84 (PIN_INPUT | MUX_MODE0) /* usbb2_hsic_strobe */
-			0x86 (PIN_INPUT | MUX_MODE0) /* usbb2_hsic_data */
-
-			0x19e (PIN_INPUT | MUX_MODE0) /* usbb3_hsic_strobe */
-			0x1a0 (PIN_INPUT | MUX_MODE0) /* usbb3_hsic_data */
-
-			0x70 (PIN_OUTPUT | MUX_MODE6) /* gpio3_80 HUB_NRESET */
-			0x6e (PIN_OUTPUT | MUX_MODE6) /* gpio3_79 ETH_NRESET */
-		>;
-	};
-
-	led_gpio_pins: pinmux_led_gpio_pins {
-		pinctrl-single,pins = <
-			0x196 (PIN_OUTPUT | MUX_MODE6) /* uart3_cts_rctx.gpio5_153 */
-		>;
-	};
-
-	uart1_pins: pinmux_uart1_pins {
-		pinctrl-single,pins = <
-			0x60 (PIN_OUTPUT | MUX_MODE0) /* uart1_tx.uart1_cts */
-			0x62 (PIN_INPUT_PULLUP | MUX_MODE0) /* uart1_tx.uart1_cts */
-			0x64 (PIN_INPUT_PULLUP | MUX_MODE0) /* uart1_rx.uart1_rts */
-			0x66 (PIN_OUTPUT | MUX_MODE0) /* uart1_rx.uart1_rts */
-		>;
-	};
-
-	uart3_pins: pinmux_uart3_pins {
-		pinctrl-single,pins = <
-			0x19a (PIN_OUTPUT | MUX_MODE0) /* uart3_rts_irsd.uart3_tx_irtx */
-			0x19c (PIN_INPUT_PULLUP | MUX_MODE0) /* uart3_rx_irrx.uart3_usbb3_hsic */
-		>;
-	};
-
-	uart5_pins: pinmux_uart5_pins {
-		pinctrl-single,pins = <
-			0x170 (PIN_INPUT_PULLUP | MUX_MODE0) /* uart5_rx.uart5_rx */
-			0x172 (PIN_OUTPUT | MUX_MODE0) /* uart5_tx.uart5_tx */
-			0x174 (PIN_INPUT_PULLUP | MUX_MODE0) /* uart5_cts.uart5_rts */
-			0x176 (PIN_OUTPUT | MUX_MODE0) /* uart5_cts.uart5_rts */
-		>;
-	};
-
-	dss_hdmi_pins: pinmux_dss_hdmi_pins {
-		pinctrl-single,pins = <
-			0x0fc (PIN_INPUT_PULLUP | MUX_MODE0)	/* hdmi_cec.hdmi_cec */
-			0x100 (PIN_INPUT | MUX_MODE0)	/* hdmi_ddc_scl.hdmi_ddc_scl */
-			0x102 (PIN_INPUT | MUX_MODE0)	/* hdmi_ddc_sda.hdmi_ddc_sda */
-		>;
-	};
-
-	tpd12s015_pins: pinmux_tpd12s015_pins {
-		pinctrl-single,pins = <
-			0x0fe (PIN_INPUT_PULLDOWN | MUX_MODE6)	/* hdmi_hpd.gpio7_193 */
-		>;
-	};
-};
-
-&omap5_pmx_wkup {
-	pinctrl-names = "default";
-	pinctrl-0 = <
-			&usbhost_wkup_pins
-	>;
-
-	usbhost_wkup_pins: pinmux_usbhost_wkup_pins {
-		pinctrl-single,pins = <
-			0x1A (PIN_OUTPUT | MUX_MODE0) /* fref_clk1_out, USB hub clk */
-		>;
-	};
-};
-
-&mmc1 {
-	vmmc-supply = <&ldo9_reg>;
-	bus-width = <4>;
-};
-
-&mmc2 {
-	vmmc-supply = <&vmmcsd_fixed>;
-	bus-width = <8>;
-	ti,non-removable;
-};
-
-&mmc3 {
-	bus-width = <4>;
-	ti,non-removable;
-};
-
-&mmc4 {
-	status = "disabled";
 };
 
-&mmc5 {
-	status = "disabled";
-};
-
-&i2c1 {
-	pinctrl-names = "default";
-	pinctrl-0 = <&i2c1_pins>;
-
-	clock-frequency = <400000>;
-
-	palmas: palmas@48 {
-		compatible = "ti,palmas";
-		interrupts = <GIC_SPI 7 IRQ_TYPE_NONE>; /* IRQ_SYS_1N */
-		reg = <0x48>;
-		interrupt-controller;
-		#interrupt-cells = <2>;
-		ti,system-power-controller;
-
-		extcon_usb3: palmas_usb {
-			compatible = "ti,palmas-usb-vid";
-			ti,enable-vbus-detection;
-			ti,enable-id-detection;
-			ti,wakeup;
-		};
-
-		clk32kgaudio: palmas_clk32k@1 {
-			compatible = "ti,palmas-clk32kgaudio";
-			#clock-cells = <0>;
-		};
-
-		palmas_pmic {
-			compatible = "ti,palmas-pmic";
-			interrupt-parent = <&palmas>;
-			interrupts = <14 IRQ_TYPE_NONE>;
-			interrupt-name = "short-irq";
-
-			ti,ldo6-vibrator;
-
-			regulators {
-				smps123_reg: smps123 {
-					/* VDD_OPP_MPU */
-					regulator-name = "smps123";
-					regulator-min-microvolt = < 600000>;
-					regulator-max-microvolt = <1500000>;
-					regulator-always-on;
-					regulator-boot-on;
-				};
-
-				smps45_reg: smps45 {
-					/* VDD_OPP_MM */
-					regulator-name = "smps45";
-					regulator-min-microvolt = < 600000>;
-					regulator-max-microvolt = <1310000>;
-					regulator-always-on;
-					regulator-boot-on;
-				};
-
-				smps6_reg: smps6 {
-					/* VDD_DDR3 - over VDD_SMPS6 */
-					regulator-name = "smps6";
-					regulator-min-microvolt = <1200000>;
-					regulator-max-microvolt = <1200000>;
-					regulator-always-on;
-					regulator-boot-on;
-				};
-
-				smps7_reg: smps7 {
-					/* VDDS_1v8_OMAP over VDDS_1v8_MAIN */
-					regulator-name = "smps7";
-					regulator-min-microvolt = <1800000>;
-					regulator-max-microvolt = <1800000>;
-					regulator-always-on;
-					regulator-boot-on;
-				};
-
-				smps8_reg: smps8 {
-					/* VDD_OPP_CORE */
-					regulator-name = "smps8";
-					regulator-min-microvolt = < 600000>;
-					regulator-max-microvolt = <1310000>;
-					regulator-always-on;
-					regulator-boot-on;
-				};
-
-				smps9_reg: smps9 {
-					/* VDDA_2v1_AUD over VDD_2v1 */
-					regulator-name = "smps9";
-					regulator-min-microvolt = <2100000>;
-					regulator-max-microvolt = <2100000>;
-					ti,smps-range = <0x80>;
-				};
-
-				smps10_out2_reg: smps10_out2 {
-					/* VBUS_5V_OTG */
-					regulator-name = "smps10_out2";
-					regulator-min-microvolt = <5000000>;
-					regulator-max-microvolt = <5000000>;
-					regulator-always-on;
-					regulator-boot-on;
-				};
-
-				smps10_out1_reg: smps10_out1 {
-					/* VBUS_5V_OTG */
-					regulator-name = "smps10_out1";
-					regulator-min-microvolt = <5000000>;
-					regulator-max-microvolt = <5000000>;
-				};
-
-				ldo1_reg: ldo1 {
-					/* VDDAPHY_CAM: vdda_csiport */
-					regulator-name = "ldo1";
-					regulator-min-microvolt = <1500000>;
-					regulator-max-microvolt = <1800000>;
-				};
-
-				ldo2_reg: ldo2 {
-					/* VCC_2V8_DISP: Does not go anywhere */
-					regulator-name = "ldo2";
-					regulator-min-microvolt = <2800000>;
-					regulator-max-microvolt = <2800000>;
-					/* Unused */
-					status = "disabled";
-				};
-
-				ldo3_reg: ldo3 {
-					/* VDDAPHY_MDM: vdda_lli */
-					regulator-name = "ldo3";
-					regulator-min-microvolt = <1500000>;
-					regulator-max-microvolt = <1500000>;
-					regulator-boot-on;
-					/* Only if Modem is used */
-					status = "disabled";
-				};
-
-				ldo4_reg: ldo4 {
-					/* VDDAPHY_DISP: vdda_dsiport/hdmi */
-					regulator-name = "ldo4";
-					regulator-min-microvolt = <1500000>;
-					regulator-max-microvolt = <1800000>;
-				};
-
-				ldo5_reg: ldo5 {
-					/* VDDA_1V8_PHY: usb/sata/hdmi.. */
-					regulator-name = "ldo5";
-					regulator-min-microvolt = <1800000>;
-					regulator-max-microvolt = <1800000>;
-					regulator-always-on;
-					regulator-boot-on;
-				};
-
-				ldo6_reg: ldo6 {
-					/* VDDS_1V2_WKUP: hsic/ldo_emu_wkup */
-					regulator-name = "ldo6";
-					regulator-min-microvolt = <1200000>;
-					regulator-max-microvolt = <1200000>;
-					regulator-always-on;
-					regulator-boot-on;
-				};
-
-				ldo7_reg: ldo7 {
-					/* VDD_VPP: vpp1 */
-					regulator-name = "ldo7";
-					regulator-min-microvolt = <2000000>;
-					regulator-max-microvolt = <2000000>;
-					/* Only for efuse reprograming! */
-					status = "disabled";
-				};
-
-				ldo8_reg: ldo8 {
-					/* VDD_3v0: Does not go anywhere */
-					regulator-name = "ldo8";
-					regulator-min-microvolt = <3000000>;
-					regulator-max-microvolt = <3000000>;
-					regulator-boot-on;
-					/* Unused */
-					status = "disabled";
-				};
-
-				ldo9_reg: ldo9 {
-					/* VCC_DV_SDIO: vdds_sdcard */
-					regulator-name = "ldo9";
-					regulator-min-microvolt = <1800000>;
-					regulator-max-microvolt = <3000000>;
-					regulator-boot-on;
-				};
-
-				ldoln_reg: ldoln {
-					/* VDDA_1v8_REF: vdds_osc/mm_l4per.. */
-					regulator-name = "ldoln";
-					regulator-min-microvolt = <1800000>;
-					regulator-max-microvolt = <1800000>;
-					regulator-always-on;
-					regulator-boot-on;
-				};
-
-				ldousb_reg: ldousb {
-					/* VDDA_3V_USB: VDDA_USBHS33 */
-					regulator-name = "ldousb";
-					regulator-min-microvolt = <3250000>;
-					regulator-max-microvolt = <3250000>;
-					regulator-always-on;
-					regulator-boot-on;
-				};
-
-				regen3_reg: regen3 {
-					/* REGEN3 controls LDO9 supply to card */
-					regulator-name = "regen3";
-					regulator-always-on;
-					regulator-boot-on;
-				};
-			};
-		};
-
-		palmas_power_button: palmas_power_button {
-			compatible = "ti,palmas-pwrbutton";
-			interrupt-parent = <&palmas>;
-			interrupts = <1 IRQ_TYPE_EDGE_FALLING>;
-			wakeup-source;
-		};
-	};
-
-	twl6040: twl@4b {
-		compatible = "ti,twl6040";
-		reg = <0x4b>;
-
-		pinctrl-names = "default";
-		pinctrl-0 = <&twl6040_pins>;
-
-		interrupts = <GIC_SPI 119 IRQ_TYPE_NONE>; /* IRQ_SYS_2N cascaded to gic */
-		ti,audpwron-gpio = <&gpio5 13 GPIO_ACTIVE_HIGH>;  /* gpio line 141 */
-
-		vio-supply = <&smps7_reg>;
-		v2v1-supply = <&smps9_reg>;
-		enable-active-high;
-
-		clocks = <&clk32kgaudio>;
-		clock-names = "clk32k";
-	};
+&hdmi {
+	vdda-supply = <&ldo4_reg>;
 };
 
 &i2c5 {
@@ -552,92 +37,17 @@
 	};
 };
 
-&mcpdm {
-	pinctrl-names = "default";
-	pinctrl-0 = <&mcpdm_pins>;
-	status = "okay";
-};
-
-&mcbsp1 {
-	pinctrl-names = "default";
-	pinctrl-0 = <&mcbsp1_pins>;
-	status = "okay";
-};
-
-&mcbsp2 {
-	pinctrl-names = "default";
-	pinctrl-0 = <&mcbsp2_pins>;
-	status = "okay";
-};
-
-&usbhshost {
-	port2-mode = "ehci-hsic";
-	port3-mode = "ehci-hsic";
-};
-
-&usbhsehci {
-	phys = <0 &hsusb2_phy &hsusb3_phy>;
-};
-
-&usb3 {
-	extcon = <&extcon_usb3>;
-	vbus-supply = <&smps10_out1_reg>;
-};
-
-&mcspi1 {
-
-};
-
-&mcspi2 {
-	pinctrl-names = "default";
-	pinctrl-0 = <&mcspi2_pins>;
-};
-
-&mcspi3 {
-	pinctrl-names = "default";
-	pinctrl-0 = <&mcspi3_pins>;
-};
-
-&mcspi4 {
-	pinctrl-names = "default";
-	pinctrl-0 = <&mcspi4_pins>;
-};
-
-&uart1 {
-	pinctrl-names = "default";
-	pinctrl-0 = <&uart1_pins>;
-};
-
-&uart3 {
-	pinctrl-names = "default";
-	pinctrl-0 = <&uart3_pins>;
-	interrupts-extended = <&wakeupgen GIC_SPI 74 IRQ_TYPE_LEVEL_HIGH>,
-			      <&omap5_pmx_core 0x19c>;
-};
-
-&uart5 {
-	pinctrl-names = "default";
-	pinctrl-0 = <&uart5_pins>;
-};
-
-&cpu0 {
-	cpu0-supply = <&smps123_reg>;
-};
-
-&dss {
-	status = "ok";
+&omap5_pmx_core {
+	i2c5_pins: pinmux_i2c5_pins {
+		pinctrl-single,pins = <
+			0x186 (PIN_INPUT | MUX_MODE0)		/* i2c5_scl */
+			0x188 (PIN_INPUT | MUX_MODE0)		/* i2c5_sda */
+		>;
+	};
 };
 
-&hdmi {
-	status = "ok";
-	vdda-supply = <&ldo4_reg>;
-
-	pinctrl-names = "default";
-	pinctrl-0 = <&dss_hdmi_pins>;
-
-	port {
-		hdmi_out: endpoint {
-			remote-endpoint = <&tpd12s015_in>;
-		};
-	};
+&tpd12s015 {
+	gpios = <&gpio9 0 GPIO_ACTIVE_HIGH>,	/* TCA6424A P01, CT CP HPD */
+		<&gpio9 1 GPIO_ACTIVE_HIGH>,	/* TCA6424A P00, LS OE */
+		<&gpio7 1 GPIO_ACTIVE_HIGH>;	/* GPIO 193, HPD */
 };