4 files changed, 109 insertions, 3 deletions
diff --git a/Documentation/acpi/enumeration.txt b/Documentation/acpi/enumeration.txt
index 94a656131885..b0d541042ac6 100644
--- a/Documentation/acpi/enumeration.txt
+++ b/Documentation/acpi/enumeration.txt
@@ -199,6 +199,8 @@ the device to the driver. For example:
 	{
 		Name (SBUF, ResourceTemplate()
 		{
+			...
+			// Used to power on/off the device
 			GpioIo (Exclusive, PullDefault, 0x0000, 0x0000,
 				IoRestrictionOutputOnly, "\\_SB.PCI0.GPI0",
 				0x00, ResourceConsumer,,)
@@ -206,10 +208,20 @@ the device to the driver. For example:
 				// Pin List
 				0x0055
 			}
+
+			// Interrupt for the device
+			GpioInt (Edge, ActiveHigh, ExclusiveAndWake, PullNone,
+				 0x0000, "\\_SB.PCI0.GPI0", 0x00, ResourceConsumer,,)
+			{
+				// Pin list
+				0x0058
+			}
+
 			...
 
-			Return (SBUF)
 		}
+
+		Return (SBUF)
 	}
 
 These GPIO numbers are controller relative and path "\\_SB.PCI0.GPI0"
@@ -220,6 +232,24 @@ The driver can do this by including <linux/acpi_gpio.h> and then calling
 acpi_get_gpio(path, gpio). This will return the Linux GPIO number or
 negative errno if there was no translation found.
 
+In a simple case of just getting the Linux GPIO number from device
+resources one can use acpi_get_gpio_by_index() helper function. It takes
+pointer to the device and index of the GpioIo/GpioInt descriptor in the
+device resources list. For example:
+
+	int gpio_irq, gpio_power;
+	int ret;
+
+	gpio_irq = acpi_get_gpio_by_index(dev, 1, NULL);
+	if (gpio_irq < 0)
+		/* handle error */
+
+	gpio_power = acpi_get_gpio_by_index(dev, 0, NULL);
+	if (gpio_power < 0)
+		/* handle error */
+
+	/* Now we can use the GPIO numbers */
+
 Other GpioIo parameters must be converted first by the driver to be
 suitable to the gpiolib before passing them.
 
diff --git a/Documentation/devicetree/bindings/gpio/gpio-grgpio.txt b/Documentation/devicetree/bindings/gpio/gpio-grgpio.txt
new file mode 100644
index 000000000000..e466598105fc
--- /dev/null
+++ b/Documentation/devicetree/bindings/gpio/gpio-grgpio.txt
@@ -0,0 +1,26 @@
+Aeroflex Gaisler GRGPIO General Purpose I/O cores.
+
+The GRGPIO GPIO core is available in the GRLIB VHDL IP core library.
+
+Note: In the ordinary environment for the GRGPIO core, a Leon SPARC system,
+these properties are built from information in the AMBA plug&play.
+
+Required properties:
+
+- name : Should be "GAISLER_GPIO" or "01_01a"
+
+- reg : Address and length of the register set for the device
+
+- interrupts : Interrupt numbers for this device
+
+Optional properties:
+
+- nbits : The number of gpio lines. If not present driver assumes 32 lines.
+
+- irqmap : An array with an index for each gpio line. An index is either a valid
+	index into the interrupts property array, or 0xffffffff that indicates
+	no irq for that line. Driver provides no interrupt support if not
+	present.
+
+For further information look in the documentation for the GLIB IP core library:
+http://www.gaisler.com/products/grlib/grip.pdf
diff --git a/Documentation/devicetree/bindings/gpio/gpio-mcp23s08.txt b/Documentation/devicetree/bindings/gpio/gpio-mcp23s08.txt
new file mode 100644
index 000000000000..629d0ef17308
--- /dev/null
+++ b/Documentation/devicetree/bindings/gpio/gpio-mcp23s08.txt
@@ -0,0 +1,47 @@
+Microchip MCP2308/MCP23S08/MCP23017/MCP23S17 driver for
+8-/16-bit I/O expander with serial interface (I2C/SPI)
+
+Required properties:
+- compatible : Should be
+    - "mcp,mcp23s08" for  8 GPIO SPI version
+    - "mcp,mcp23s17" for 16 GPIO SPI version
+    - "mcp,mcp23008" for  8 GPIO I2C version or
+    - "mcp,mcp23017" for 16 GPIO I2C version of the chip
+- #gpio-cells : Should be two.
+  - first cell is the pin number
+  - second cell is used to specify flags. Flags are currently unused.
+- gpio-controller : Marks the device node as a GPIO controller.
+- reg : For an address on its bus. I2C uses this a the I2C address of the chip.
+        SPI uses this to specify the chipselect line which the chip is
+        connected to. The driver and the SPI variant of the chip support
+        multiple chips on the same chipselect. Have a look at
+        mcp,spi-present-mask below.
+
+Required device specific properties (only for SPI chips):
+- mcp,spi-present-mask : This is a present flag, that makes only sense for SPI
+        chips - as the name suggests. Multiple SPI chips can share the same
+        SPI chipselect. Set a bit in bit0-7 in this mask to 1 if there is a
+        chip connected with the corresponding spi address set. For example if
+        you have a chip with address 3 connected, you have to set bit3 to 1,
+        which is 0x08. mcp23s08 chip variant only supports bits 0-3. It is not
+        possible to mix mcp23s08 and mcp23s17 on the same chipselect. Set at
+        least one bit to 1 for SPI chips.
+- spi-max-frequency = The maximum frequency this chip is able to handle
+
+Example I2C:
+gpiom1: gpio@20 {
+        compatible = "mcp,mcp23017";
+        gpio-controller;
+        #gpio-cells = <2>;
+        reg = <0x20>;
+};
+
+Example SPI:
+gpiom1: gpio@0 {
+        compatible = "mcp,mcp23s17";
+        gpio-controller;
+        #gpio-cells = <2>;
+        spi-present-mask = <0x01>;
+        reg = <0>;
+        spi-max-frequency = <1000000>;
+};
diff --git a/Documentation/devicetree/bindings/gpio/gpio-omap.txt b/Documentation/devicetree/bindings/gpio/gpio-omap.txt
index bff51a2fee1e..1b524c0c79fe 100644
--- a/Documentation/devicetree/bindings/gpio/gpio-omap.txt
+++ b/Documentation/devicetree/bindings/gpio/gpio-omap.txt
@@ -20,8 +20,11 @@ Required properties:
       8 = active low level-sensitive.
 
 OMAP specific properties:
-- ti,hwmods: Name of the hwmod associated to the GPIO:
-  "gpio<X>", <X> being the 1-based instance number from the HW spec
+- ti,hwmods:		Name of the hwmod associated to the GPIO:
+			"gpio<X>", <X> being the 1-based instance number
+			from the HW spec.
+- ti,gpio-always-on: 	Indicates if a GPIO bank is always powered and
+			so will never lose its logic state.
 
 
 Example: