e1000e: add support for 82577/82578 GbE LOM parts

This patch provides support for the next generation Intel desktop
and mobile gigabit ethernet LOM adapters.  These adapters are the
follow-on parts to the LOMs tied to the prior ICH chipsets and are
comprised of a MAC in the PCH chipset and an external PHY (82577 for
mobile and 82578 for desktop versions).  New features consist of PHY
wakeup to save power by completely turning off the MAC while in Sx
state, and 4K jumbo frames.

Signed-off-by: Bruce Allan <bruce.w.allan@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

1 files changed, 682 insertions, 17 deletions

diff --git a/drivers/net/e1000e/phy.c b/drivers/net/e1000e/phy.c
index dc4a9cba6a73..e23459cf3d0e 100644
--- a/drivers/net/e1000e/phy.c
+++ b/drivers/net/e1000e/phy.c
@@ -37,6 +37,9 @@ static s32 e1000_wait_autoneg(struct e1000_hw *hw);
 static u32 e1000_get_phy_addr_for_bm_page(u32 page, u32 reg);
 static s32 e1000_access_phy_wakeup_reg_bm(struct e1000_hw *hw, u32 offset,
 					  u16 *data, bool read);
+static u32 e1000_get_phy_addr_for_hv_page(u32 page);
+static s32 e1000_access_phy_debug_regs_hv(struct e1000_hw *hw, u32 offset,
+                                          u16 *data, bool read);
 
 /* Cable length tables */
 static const u16 e1000_m88_cable_length_table[] =
@@ -54,6 +57,55 @@ static const u16 e1000_igp_2_cable_length_table[] =
 #define IGP02E1000_CABLE_LENGTH_TABLE_SIZE \
 		ARRAY_SIZE(e1000_igp_2_cable_length_table)
 
+#define BM_PHY_REG_PAGE(offset) \
+	((u16)(((offset) >> PHY_PAGE_SHIFT) & 0xFFFF))
+#define BM_PHY_REG_NUM(offset) \
+	((u16)(((offset) & MAX_PHY_REG_ADDRESS) |\
+	 (((offset) >> (PHY_UPPER_SHIFT - PHY_PAGE_SHIFT)) &\
+		~MAX_PHY_REG_ADDRESS)))
+
+#define HV_INTC_FC_PAGE_START             768
+#define I82578_ADDR_REG                   29
+#define I82577_ADDR_REG                   16
+#define I82577_CFG_REG                    22
+#define I82577_CFG_ASSERT_CRS_ON_TX       (1 << 15)
+#define I82577_CFG_ENABLE_DOWNSHIFT       (3 << 10) /* auto downshift 100/10 */
+#define I82577_CTRL_REG                   23
+#define I82577_CTRL_DOWNSHIFT_MASK        (7 << 10)
+
+/* 82577 specific PHY registers */
+#define I82577_PHY_CTRL_2            18
+#define I82577_PHY_STATUS_2          26
+#define I82577_PHY_DIAG_STATUS       31
+
+/* I82577 PHY Status 2 */
+#define I82577_PHY_STATUS2_REV_POLARITY   0x0400
+#define I82577_PHY_STATUS2_MDIX           0x0800
+#define I82577_PHY_STATUS2_SPEED_MASK     0x0300
+#define I82577_PHY_STATUS2_SPEED_1000MBPS 0x0200
+
+/* I82577 PHY Control 2 */
+#define I82577_PHY_CTRL2_AUTO_MDIX        0x0400
+#define I82577_PHY_CTRL2_FORCE_MDI_MDIX   0x0200
+
+/* I82577 PHY Diagnostics Status */
+#define I82577_DSTATUS_CABLE_LENGTH       0x03FC
+#define I82577_DSTATUS_CABLE_LENGTH_SHIFT 2
+
+/* BM PHY Copper Specific Control 1 */
+#define BM_CS_CTRL1                       16
+
+/* BM PHY Copper Specific Status */
+#define BM_CS_STATUS                      17
+#define BM_CS_STATUS_LINK_UP              0x0400
+#define BM_CS_STATUS_RESOLVED             0x0800
+#define BM_CS_STATUS_SPEED_MASK           0xC000
+#define BM_CS_STATUS_SPEED_1000           0x8000
+
+#define HV_MUX_DATA_CTRL               PHY_REG(776, 16)
+#define HV_MUX_DATA_CTRL_GEN_TO_MAC    0x0400
+#define HV_MUX_DATA_CTRL_FORCE_SPEED   0x0004
+
 /**
  *  e1000e_check_reset_block_generic - Check if PHY reset is blocked
  *  @hw: pointer to the HW structure
@@ -82,23 +134,48 @@ s32 e1000e_check_reset_block_generic(struct e1000_hw *hw)
 s32 e1000e_get_phy_id(struct e1000_hw *hw)
 {
 	struct e1000_phy_info *phy = &hw->phy;
-	s32 ret_val;
+	s32 ret_val = 0;
 	u16 phy_id;
+	u16 retry_count = 0;
 
-	ret_val = e1e_rphy(hw, PHY_ID1, &phy_id);
-	if (ret_val)
-		return ret_val;
+	if (!(phy->ops.read_phy_reg))
+		goto out;
 
-	phy->id = (u32)(phy_id << 16);
-	udelay(20);
-	ret_val = e1e_rphy(hw, PHY_ID2, &phy_id);
-	if (ret_val)
-		return ret_val;
+	while (retry_count < 2) {
+		ret_val = e1e_rphy(hw, PHY_ID1, &phy_id);
+		if (ret_val)
+			goto out;
 
-	phy->id |= (u32)(phy_id & PHY_REVISION_MASK);
-	phy->revision = (u32)(phy_id & ~PHY_REVISION_MASK);
+		phy->id = (u32)(phy_id << 16);
+		udelay(20);
+		ret_val = e1e_rphy(hw, PHY_ID2, &phy_id);
+		if (ret_val)
+			goto out;
 
-	return 0;
+		phy->id |= (u32)(phy_id & PHY_REVISION_MASK);
+		phy->revision = (u32)(phy_id & ~PHY_REVISION_MASK);
+
+		if (phy->id != 0 && phy->id != PHY_REVISION_MASK)
+			goto out;
+
+		/*
+		 * If the PHY ID is still unknown, we may have an 82577i
+		 * without link.  We will try again after setting Slow
+		 * MDIC mode. No harm in trying again in this case since
+		 * the PHY ID is unknown at this point anyway
+		 */
+		ret_val = e1000_set_mdio_slow_mode_hv(hw, true);
+		if (ret_val)
+			goto out;
+
+		retry_count++;
+	}
+out:
+	/* Revert to MDIO fast mode, if applicable */
+	if (retry_count)
+		ret_val = e1000_set_mdio_slow_mode_hv(hw, false);
+
+	return ret_val;
 }
 
 /**
@@ -410,6 +487,43 @@ s32 e1000e_write_kmrn_reg(struct e1000_hw *hw, u32 offset, u16 data)
 }
 
 /**
+ *  e1000_copper_link_setup_82577 - Setup 82577 PHY for copper link
+ *  @hw: pointer to the HW structure
+ *
+ *  Sets up Carrier-sense on Transmit and downshift values.
+ **/
+s32 e1000_copper_link_setup_82577(struct e1000_hw *hw)
+{
+	struct e1000_phy_info *phy = &hw->phy;
+	s32 ret_val;
+	u16 phy_data;
+
+	/* Enable CRS on TX. This must be set for half-duplex operation. */
+	ret_val = phy->ops.read_phy_reg(hw, I82577_CFG_REG, &phy_data);
+	if (ret_val)
+		goto out;
+
+	phy_data |= I82577_CFG_ASSERT_CRS_ON_TX;
+
+	/* Enable downshift */
+	phy_data |= I82577_CFG_ENABLE_DOWNSHIFT;
+
+	ret_val = phy->ops.write_phy_reg(hw, I82577_CFG_REG, phy_data);
+	if (ret_val)
+		goto out;
+
+	/* Set number of link attempts before downshift */
+	ret_val = phy->ops.read_phy_reg(hw, I82577_CTRL_REG, &phy_data);
+	if (ret_val)
+		goto out;
+	phy_data &= ~I82577_CTRL_DOWNSHIFT_MASK;
+	ret_val = phy->ops.write_phy_reg(hw, I82577_CTRL_REG, phy_data);
+
+out:
+	return ret_val;
+}
+
+/**
  *  e1000e_copper_link_setup_m88 - Setup m88 PHY's for copper link
  *  @hw: pointer to the HW structure
  *
@@ -427,8 +541,8 @@ s32 e1000e_copper_link_setup_m88(struct e1000_hw *hw)
 	if (ret_val)
 		return ret_val;
 
-	/* For newer PHYs this bit is downshift enable */
-	if (phy->type == e1000_phy_m88)
+	/* For BM PHY this bit is downshift enable */
+	if (phy->type != e1000_phy_bm)
 		phy_data |= M88E1000_PSCR_ASSERT_CRS_ON_TX;
 
 	/*
@@ -520,10 +634,27 @@ s32 e1000e_copper_link_setup_m88(struct e1000_hw *hw)
 
 	/* Commit the changes. */
 	ret_val = e1000e_commit_phy(hw);
-	if (ret_val)
+	if (ret_val) {
 		hw_dbg(hw, "Error committing the PHY changes\n");
+		return ret_val;
+	}
 
-	return ret_val;
+	if (phy->type == e1000_phy_82578) {
+		ret_val = phy->ops.read_phy_reg(hw, M88E1000_EXT_PHY_SPEC_CTRL,
+		                            &phy_data);
+		if (ret_val)
+			return ret_val;
+
+		/* 82578 PHY - set the downshift count to 1x. */
+		phy_data |= I82578_EPSCR_DOWNSHIFT_ENABLE;
+		phy_data &= ~I82578_EPSCR_DOWNSHIFT_COUNTER_MASK;
+		ret_val = phy->ops.write_phy_reg(hw, M88E1000_EXT_PHY_SPEC_CTRL,
+		                             phy_data);
+		if (ret_val)
+			return ret_val;
+	}
+
+	return 0;
 }
 
 /**
@@ -1251,6 +1382,8 @@ s32 e1000e_check_downshift(struct e1000_hw *hw)
 	switch (phy->type) {
 	case e1000_phy_m88:
 	case e1000_phy_gg82563:
+	case e1000_phy_82578:
+	case e1000_phy_82577:
 		offset	= M88E1000_PHY_SPEC_STATUS;
 		mask	= M88E1000_PSSR_DOWNSHIFT;
 		break;
@@ -1886,6 +2019,12 @@ enum e1000_phy_type e1000e_get_phy_type_from_id(u32 phy_id)
 	case BME1000_E_PHY_ID_R2:
 		phy_type = e1000_phy_bm;
 		break;
+	case I82578_E_PHY_ID:
+		phy_type = e1000_phy_82578;
+		break;
+	case I82577_E_PHY_ID:
+		phy_type = e1000_phy_82577;
+		break;
 	default:
 		phy_type = e1000_phy_unknown;
 		break;
@@ -2181,11 +2320,16 @@ static s32 e1000_access_phy_wakeup_reg_bm(struct e1000_hw *hw, u32 offset,
 					  u16 *data, bool read)
 {
 	s32 ret_val;
-	u16 reg = ((u16)offset) & PHY_REG_MASK;
+	u16 reg = BM_PHY_REG_NUM(offset);
 	u16 phy_reg = 0;
 	u8  phy_acquired = 1;
 
 
+	/* Gig must be disabled for MDIO accesses to page 800 */
+	if ((hw->mac.type == e1000_pchlan) &&
+	   (!(er32(PHY_CTRL) & E1000_PHY_CTRL_GBE_DISABLE)))
+		hw_dbg(hw, "Attempting to access page 800 while gig enabled\n");
+
 	ret_val = hw->phy.ops.acquire_phy(hw);
 	if (ret_val) {
 		phy_acquired = 0;
@@ -2289,3 +2433,524 @@ static s32 e1000_set_d0_lplu_state(struct e1000_hw *hw, bool active)
 
 	return 0;
 }
+
+s32 e1000_set_mdio_slow_mode_hv(struct e1000_hw *hw, bool slow)
+{
+	s32 ret_val = 0;
+	u16 data = 0;
+
+	ret_val = hw->phy.ops.acquire_phy(hw);
+	if (ret_val)
+		return ret_val;
+
+	/* Set MDIO mode - page 769, register 16: 0x2580==slow, 0x2180==fast */
+	hw->phy.addr = 1;
+	ret_val = e1000e_write_phy_reg_mdic(hw, IGP01E1000_PHY_PAGE_SELECT,
+				         (BM_PORT_CTRL_PAGE << IGP_PAGE_SHIFT));
+	if (ret_val) {
+		hw->phy.ops.release_phy(hw);
+		return ret_val;
+	}
+	ret_val = e1000e_write_phy_reg_mdic(hw, BM_CS_CTRL1,
+	                                   (0x2180 | (slow << 10)));
+
+	/* dummy read when reverting to fast mode - throw away result */
+	if (!slow)
+		e1000e_read_phy_reg_mdic(hw, BM_CS_CTRL1, &data);
+
+	hw->phy.ops.release_phy(hw);
+
+	return ret_val;
+}
+
+/**
+ *  e1000_read_phy_reg_hv -  Read HV PHY register
+ *  @hw: pointer to the HW structure
+ *  @offset: register offset to be read
+ *  @data: pointer to the read data
+ *
+ *  Acquires semaphore, if necessary, then reads the PHY register at offset
+ *  and storing the retrieved information in data.  Release any acquired
+ *  semaphore before exiting.
+ **/
+s32 e1000_read_phy_reg_hv(struct e1000_hw *hw, u32 offset, u16 *data)
+{
+	s32 ret_val;
+	u16 page = BM_PHY_REG_PAGE(offset);
+	u16 reg = BM_PHY_REG_NUM(offset);
+	bool in_slow_mode = false;
+
+	/* Workaround failure in MDIO access while cable is disconnected */
+	if ((hw->phy.type == e1000_phy_82577) &&
+	    !(er32(STATUS) & E1000_STATUS_LU)) {
+		ret_val = e1000_set_mdio_slow_mode_hv(hw, true);
+		if (ret_val)
+			goto out;
+
+		in_slow_mode = true;
+	}
+
+	/* Page 800 works differently than the rest so it has its own func */
+	if (page == BM_WUC_PAGE) {
+		ret_val = e1000_access_phy_wakeup_reg_bm(hw, offset,
+		                                         data, true);
+		goto out;
+	}
+
+	if (page > 0 && page < HV_INTC_FC_PAGE_START) {
+		ret_val = e1000_access_phy_debug_regs_hv(hw, offset,
+		                                         data, true);
+		goto out;
+	}
+
+	ret_val = hw->phy.ops.acquire_phy(hw);
+	if (ret_val)
+		goto out;
+
+	hw->phy.addr = e1000_get_phy_addr_for_hv_page(page);
+
+	if (page == HV_INTC_FC_PAGE_START)
+		page = 0;
+
+	if (reg > MAX_PHY_MULTI_PAGE_REG) {
+		if ((hw->phy.type != e1000_phy_82578) ||
+		    ((reg != I82578_ADDR_REG) &&
+		     (reg != I82578_ADDR_REG + 1))) {
+			u32 phy_addr = hw->phy.addr;
+
+			hw->phy.addr = 1;
+
+			/* Page is shifted left, PHY expects (page x 32) */
+			ret_val = e1000e_write_phy_reg_mdic(hw,
+			                             IGP01E1000_PHY_PAGE_SELECT,
+			                             (page << IGP_PAGE_SHIFT));
+			if (ret_val) {
+				hw->phy.ops.release_phy(hw);
+				goto out;
+			}
+			hw->phy.addr = phy_addr;
+		}
+	}
+
+	ret_val = e1000e_read_phy_reg_mdic(hw, MAX_PHY_REG_ADDRESS & reg,
+	                                  data);
+	hw->phy.ops.release_phy(hw);
+
+out:
+	/* Revert to MDIO fast mode, if applicable */
+	if ((hw->phy.type == e1000_phy_82577) && in_slow_mode)
+		ret_val = e1000_set_mdio_slow_mode_hv(hw, false);
+
+	return ret_val;
+}
+
+/**
+ *  e1000_write_phy_reg_hv - Write HV PHY register
+ *  @hw: pointer to the HW structure
+ *  @offset: register offset to write to
+ *  @data: data to write at register offset
+ *
+ *  Acquires semaphore, if necessary, then writes the data to PHY register
+ *  at the offset.  Release any acquired semaphores before exiting.
+ **/
+s32 e1000_write_phy_reg_hv(struct e1000_hw *hw, u32 offset, u16 data)
+{
+	s32 ret_val;
+	u16 page = BM_PHY_REG_PAGE(offset);
+	u16 reg = BM_PHY_REG_NUM(offset);
+	bool in_slow_mode = false;
+
+	/* Workaround failure in MDIO access while cable is disconnected */
+	if ((hw->phy.type == e1000_phy_82577) &&
+	    !(er32(STATUS) & E1000_STATUS_LU)) {
+		ret_val = e1000_set_mdio_slow_mode_hv(hw, true);
+		if (ret_val)
+			goto out;
+
+		in_slow_mode = true;
+	}
+
+	/* Page 800 works differently than the rest so it has its own func */
+	if (page == BM_WUC_PAGE) {
+		ret_val = e1000_access_phy_wakeup_reg_bm(hw, offset,
+		                                         &data, false);
+		goto out;
+	}
+
+	if (page > 0 && page < HV_INTC_FC_PAGE_START) {
+		ret_val = e1000_access_phy_debug_regs_hv(hw, offset,
+		                                         &data, false);
+		goto out;
+	}
+
+	ret_val = hw->phy.ops.acquire_phy(hw);
+	if (ret_val)
+		goto out;
+
+	hw->phy.addr = e1000_get_phy_addr_for_hv_page(page);
+
+	if (page == HV_INTC_FC_PAGE_START)
+		page = 0;
+
+	/*
+	 * Workaround MDIO accesses being disabled after entering IEEE Power
+	 * Down (whenever bit 11 of the PHY Control register is set)
+	 */
+	if ((hw->phy.type == e1000_phy_82578) &&
+	    (hw->phy.revision >= 1) &&
+	    (hw->phy.addr == 2) &&
+	    ((MAX_PHY_REG_ADDRESS & reg) == 0) &&
+	    (data & (1 << 11))) {
+		u16 data2 = 0x7EFF;
+		hw->phy.ops.release_phy(hw);
+		ret_val = e1000_access_phy_debug_regs_hv(hw, (1 << 6) | 0x3,
+		                                         &data2, false);
+		if (ret_val)
+			goto out;
+
+		ret_val = hw->phy.ops.acquire_phy(hw);
+		if (ret_val)
+			goto out;
+	}
+
+	if (reg > MAX_PHY_MULTI_PAGE_REG) {
+		if ((hw->phy.type != e1000_phy_82578) ||
+		    ((reg != I82578_ADDR_REG) &&
+		     (reg != I82578_ADDR_REG + 1))) {
+			u32 phy_addr = hw->phy.addr;
+
+			hw->phy.addr = 1;
+
+			/* Page is shifted left, PHY expects (page x 32) */
+			ret_val = e1000e_write_phy_reg_mdic(hw,
+			                             IGP01E1000_PHY_PAGE_SELECT,
+			                             (page << IGP_PAGE_SHIFT));
+			if (ret_val) {
+				hw->phy.ops.release_phy(hw);
+				goto out;
+			}
+			hw->phy.addr = phy_addr;
+		}
+	}
+
+	ret_val = e1000e_write_phy_reg_mdic(hw, MAX_PHY_REG_ADDRESS & reg,
+	                                  data);
+	hw->phy.ops.release_phy(hw);
+
+out:
+	/* Revert to MDIO fast mode, if applicable */
+	if ((hw->phy.type == e1000_phy_82577) && in_slow_mode)
+		ret_val = e1000_set_mdio_slow_mode_hv(hw, false);
+
+	return ret_val;
+}
+
+/**
+ *  e1000_get_phy_addr_for_hv_page - Get PHY adrress based on page
+ *  @page: page to be accessed
+ **/
+static u32 e1000_get_phy_addr_for_hv_page(u32 page)
+{
+	u32 phy_addr = 2;
+
+	if (page >= HV_INTC_FC_PAGE_START)
+		phy_addr = 1;
+
+	return phy_addr;
+}
+
+/**
+ *  e1000_access_phy_debug_regs_hv - Read HV PHY vendor specific high registers
+ *  @hw: pointer to the HW structure
+ *  @offset: register offset to be read or written
+ *  @data: pointer to the data to be read or written
+ *  @read: determines if operation is read or written
+ *
+ *  Acquires semaphore, if necessary, then reads the PHY register at offset
+ *  and storing the retreived information in data.  Release any acquired
+ *  semaphores before exiting.  Note that the procedure to read these regs
+ *  uses the address port and data port to read/write.
+ **/
+static s32 e1000_access_phy_debug_regs_hv(struct e1000_hw *hw, u32 offset,
+                                          u16 *data, bool read)
+{
+	s32 ret_val;
+	u32 addr_reg = 0;
+	u32 data_reg = 0;
+	u8  phy_acquired = 1;
+
+	/* This takes care of the difference with desktop vs mobile phy */
+	addr_reg = (hw->phy.type == e1000_phy_82578) ?
+	           I82578_ADDR_REG : I82577_ADDR_REG;
+	data_reg = addr_reg + 1;
+
+	ret_val = hw->phy.ops.acquire_phy(hw);
+	if (ret_val) {
+		hw_dbg(hw, "Could not acquire PHY\n");
+		phy_acquired = 0;
+		goto out;
+	}
+
+	/* All operations in this function are phy address 2 */
+	hw->phy.addr = 2;
+
+	/* masking with 0x3F to remove the page from offset */
+	ret_val = e1000e_write_phy_reg_mdic(hw, addr_reg, (u16)offset & 0x3F);
+	if (ret_val) {
+		hw_dbg(hw, "Could not write PHY the HV address register\n");
+		goto out;
+	}
+
+	/* Read or write the data value next */
+	if (read)
+		ret_val = e1000e_read_phy_reg_mdic(hw, data_reg, data);
+	else
+		ret_val = e1000e_write_phy_reg_mdic(hw, data_reg, *data);
+
+	if (ret_val) {
+		hw_dbg(hw, "Could not read data value from HV data register\n");
+		goto out;
+	}
+
+out:
+	if (phy_acquired == 1)
+		hw->phy.ops.release_phy(hw);
+	return ret_val;
+}
+
+/**
+ *  e1000_link_stall_workaround_hv - Si workaround
+ *  @hw: pointer to the HW structure
+ *
+ *  This function works around a Si bug where the link partner can get
+ *  a link up indication before the PHY does.  If small packets are sent
+ *  by the link partner they can be placed in the packet buffer without
+ *  being properly accounted for by the PHY and will stall preventing
+ *  further packets from being received.  The workaround is to clear the
+ *  packet buffer after the PHY detects link up.
+ **/
+s32 e1000_link_stall_workaround_hv(struct e1000_hw *hw)
+{
+	s32 ret_val = 0;
+	u16 data;
+
+	if (hw->phy.type != e1000_phy_82578)
+		goto out;
+
+	/* check if link is up and at 1Gbps */
+	ret_val = hw->phy.ops.read_phy_reg(hw, BM_CS_STATUS, &data);
+	if (ret_val)
+		goto out;
+
+	data &= BM_CS_STATUS_LINK_UP |
+	        BM_CS_STATUS_RESOLVED |
+	        BM_CS_STATUS_SPEED_MASK;
+
+	if (data != (BM_CS_STATUS_LINK_UP |
+	             BM_CS_STATUS_RESOLVED |
+	             BM_CS_STATUS_SPEED_1000))
+		goto out;
+
+	mdelay(200);
+
+	/* flush the packets in the fifo buffer */
+	ret_val = hw->phy.ops.write_phy_reg(hw, HV_MUX_DATA_CTRL,
+	                                HV_MUX_DATA_CTRL_GEN_TO_MAC |
+	                                HV_MUX_DATA_CTRL_FORCE_SPEED);
+	if (ret_val)
+		goto out;
+
+	ret_val = hw->phy.ops.write_phy_reg(hw, HV_MUX_DATA_CTRL,
+	                                HV_MUX_DATA_CTRL_GEN_TO_MAC);
+
+out:
+	return ret_val;
+}
+
+/**
+ *  e1000_check_polarity_82577 - Checks the polarity.
+ *  @hw: pointer to the HW structure
+ *
+ *  Success returns 0, Failure returns -E1000_ERR_PHY (-2)
+ *
+ *  Polarity is determined based on the PHY specific status register.
+ **/
+s32 e1000_check_polarity_82577(struct e1000_hw *hw)
+{
+	struct e1000_phy_info *phy = &hw->phy;
+	s32 ret_val;
+	u16 data;
+
+	ret_val = phy->ops.read_phy_reg(hw, I82577_PHY_STATUS_2, &data);
+
+	if (!ret_val)
+		phy->cable_polarity = (data & I82577_PHY_STATUS2_REV_POLARITY)
+		                      ? e1000_rev_polarity_reversed
+		                      : e1000_rev_polarity_normal;
+
+	return ret_val;
+}
+
+/**
+ *  e1000_phy_force_speed_duplex_82577 - Force speed/duplex for I82577 PHY
+ *  @hw: pointer to the HW structure
+ *
+ *  Calls the PHY setup function to force speed and duplex.  Clears the
+ *  auto-crossover to force MDI manually.  Waits for link and returns
+ *  successful if link up is successful, else -E1000_ERR_PHY (-2).
+ **/
+s32 e1000_phy_force_speed_duplex_82577(struct e1000_hw *hw)
+{
+	struct e1000_phy_info *phy = &hw->phy;
+	s32 ret_val;
+	u16 phy_data;
+	bool link;
+
+	ret_val = phy->ops.read_phy_reg(hw, PHY_CONTROL, &phy_data);
+	if (ret_val)
+		goto out;
+
+	e1000e_phy_force_speed_duplex_setup(hw, &phy_data);
+
+	ret_val = phy->ops.write_phy_reg(hw, PHY_CONTROL, phy_data);
+	if (ret_val)
+		goto out;
+
+	/*
+	 * Clear Auto-Crossover to force MDI manually.  82577 requires MDI
+	 * forced whenever speed and duplex are forced.
+	 */
+	ret_val = phy->ops.read_phy_reg(hw, I82577_PHY_CTRL_2, &phy_data);
+	if (ret_val)
+		goto out;
+
+	phy_data &= ~I82577_PHY_CTRL2_AUTO_MDIX;
+	phy_data &= ~I82577_PHY_CTRL2_FORCE_MDI_MDIX;
+
+	ret_val = phy->ops.write_phy_reg(hw, I82577_PHY_CTRL_2, phy_data);
+	if (ret_val)
+		goto out;
+
+	hw_dbg(hw, "I82577_PHY_CTRL_2: %X\n", phy_data);
+
+	udelay(1);
+
+	if (phy->autoneg_wait_to_complete) {
+		hw_dbg(hw, "Waiting for forced speed/duplex link on 82577 phy\n");
+
+		ret_val = e1000e_phy_has_link_generic(hw,
+		                                     PHY_FORCE_LIMIT,
+		                                     100000,
+		                                     &link);
+		if (ret_val)
+			goto out;
+
+		if (!link)
+			hw_dbg(hw, "Link taking longer than expected.\n");
+
+		/* Try once more */
+		ret_val = e1000e_phy_has_link_generic(hw,
+		                                     PHY_FORCE_LIMIT,
+		                                     100000,
+		                                     &link);
+		if (ret_val)
+			goto out;
+	}
+
+out:
+	return ret_val;
+}
+
+/**
+ *  e1000_get_phy_info_82577 - Retrieve I82577 PHY information
+ *  @hw: pointer to the HW structure
+ *
+ *  Read PHY status to determine if link is up.  If link is up, then
+ *  set/determine 10base-T extended distance and polarity correction.  Read
+ *  PHY port status to determine MDI/MDIx and speed.  Based on the speed,
+ *  determine on the cable length, local and remote receiver.
+ **/
+s32 e1000_get_phy_info_82577(struct e1000_hw *hw)
+{
+	struct e1000_phy_info *phy = &hw->phy;
+	s32 ret_val;
+	u16 data;
+	bool link;
+
+	ret_val = e1000e_phy_has_link_generic(hw, 1, 0, &link);
+	if (ret_val)
+		goto out;
+
+	if (!link) {
+		hw_dbg(hw, "Phy info is only valid if link is up\n");
+		ret_val = -E1000_ERR_CONFIG;
+		goto out;
+	}
+
+	phy->polarity_correction = true;
+
+	ret_val = e1000_check_polarity_82577(hw);
+	if (ret_val)
+		goto out;
+
+	ret_val = phy->ops.read_phy_reg(hw, I82577_PHY_STATUS_2, &data);
+	if (ret_val)
+		goto out;
+
+	phy->is_mdix = (data & I82577_PHY_STATUS2_MDIX) ? true : false;
+
+	if ((data & I82577_PHY_STATUS2_SPEED_MASK) ==
+	    I82577_PHY_STATUS2_SPEED_1000MBPS) {
+		ret_val = hw->phy.ops.get_cable_length(hw);
+		if (ret_val)
+			goto out;
+
+		ret_val = phy->ops.read_phy_reg(hw, PHY_1000T_STATUS, &data);
+		if (ret_val)
+			goto out;
+
+		phy->local_rx = (data & SR_1000T_LOCAL_RX_STATUS)
+		                ? e1000_1000t_rx_status_ok
+		                : e1000_1000t_rx_status_not_ok;
+
+		phy->remote_rx = (data & SR_1000T_REMOTE_RX_STATUS)
+		                 ? e1000_1000t_rx_status_ok
+		                 : e1000_1000t_rx_status_not_ok;
+	} else {
+		phy->cable_length = E1000_CABLE_LENGTH_UNDEFINED;
+		phy->local_rx = e1000_1000t_rx_status_undefined;
+		phy->remote_rx = e1000_1000t_rx_status_undefined;
+	}
+
+out:
+	return ret_val;
+}
+
+/**
+ *  e1000_get_cable_length_82577 - Determine cable length for 82577 PHY
+ *  @hw: pointer to the HW structure
+ *
+ * Reads the diagnostic status register and verifies result is valid before
+ * placing it in the phy_cable_length field.
+ **/
+s32 e1000_get_cable_length_82577(struct e1000_hw *hw)
+{
+	struct e1000_phy_info *phy = &hw->phy;
+	s32 ret_val;
+	u16 phy_data, length;
+
+	ret_val = phy->ops.read_phy_reg(hw, I82577_PHY_DIAG_STATUS, &phy_data);
+	if (ret_val)
+		goto out;
+
+	length = (phy_data & I82577_DSTATUS_CABLE_LENGTH) >>
+	         I82577_DSTATUS_CABLE_LENGTH_SHIFT;
+
+	if (length == E1000_CABLE_LENGTH_UNDEFINED)
+		ret_val = E1000_ERR_PHY;
+
+	phy->cable_length = length;
+
+out:
+	return ret_val;
+}