1
2
3
4
5
6
7
8
9
10
11
12
13
14
15
16
17
18
19
20
21
22
23
24
25
26
27
28
29
30
31
32
33
34
35
36
37
38
39
40
41
42
43
44
45
46
47
48
49
50
51
52
53
54
55
56
57
58
59
60
61
62
63
64
65
66
67
68
69
70
71
72
73
74
75
76
77
78
79
80
81
82
83
84
85
86
87
88
89
90
91
92
93
94
95
96
97
98
99
100
101
102
103
104
105
106
107
108
109
110
111
112
113
114
115
116
117
118
119
120
121
122
123
124
125
126
127
128
129
130
131
132
133
134
135
136
137
138
139
140
141
142
143
144
145
146
147
148
149
150
151
152
153
154
155
156
157
158
159
160
161
162
163
164
165
166
167
168
169
170
171
172
173
174
175
176
177
178
179
180
181
182
183
184
185
186
187
188
189
190
191
192
193
194
195
196
197
198
199
200
201
202
203
204
205
206
207
208
209
210
211
212
213
214
215
216
217
218
219
220
221
222
223
224
225
226
227
228
229
230
231
232
233
234
235
236
237
238
239
240
241
242
243
244
245
246
247
248
249
250
251
252
253
254
255
256
257
258
259
260
261
262
263
264
265
266
267
268
269
270
271
272
273
274
275
276
277
278
279
280
281
282
283
284
285
286
287
288
289
290
291
292
293
294
295
296
297
298
299
300
301
302
303
304
305
306
307
308
309
310
311
312
313
314
315
316
317
318
319
320
321
322
323
324
325
326
327
328
329
330
331
332
333
334
335
336
337
338
339
340
341
342
343
344
345
346
347
348
349
350
351
352
353
354
355
356
357
358
359
360
361
362
363
364
365
366
367
368
369
370
371
372
373
374
375
376
377
378
379
380
381
382
383
384
|
.. SPDX-License-Identifier: GPL-2.0
================
ADIS16475 driver
================
This driver supports Analog Device's IMUs on SPI bus.
1. Supported devices
====================
* `ADIS16465 <https://www.analog.com/ADIS16465>`_
* `ADIS16467 <https://www.analog.com/ADIS16467>`_
* `ADIS16470 <https://www.analog.com/ADIS16470>`_
* `ADIS16475 <https://www.analog.com/ADIS16475>`_
* `ADIS16477 <https://www.analog.com/ADIS16477>`_
* `ADIS16500 <https://www.analog.com/ADIS16500>`_
* `ADIS16505 <https://www.analog.com/ADIS16505>`_
* `ADIS16507 <https://www.analog.com/ADIS16507>`_
Each supported device is a precision, miniature microelectromechanical system
(MEMS) inertial measurement unit (IMU) that includes a triaxial gyroscope and a
triaxial accelerometer. Each inertial sensor in the IMU device combines with
signal conditioning that optimizes dynamic performance. The factory calibration
characterizes each sensor for sensitivity, bias, alignment, linear acceleration
(gyroscope bias), and point of percussion (accelerometer location). As a result,
each sensor has dynamic compensation formulas that provide accurate sensor
measurements over a broad set of conditions.
2. Device attributes
====================
Accelerometer, gyroscope measurements are always provided. Furthermore, the
driver offers the capability to retrieve the delta angle and the delta velocity
measurements computed by the device.
The delta angle measurements represent a calculation of angular displacement
between each sample update, while the delta velocity measurements represent a
calculation of linear velocity change between each sample update.
Finally, temperature data are provided which show a coarse measurement of
the temperature inside of the IMU device. This data is most useful for
monitoring relative changes in the thermal environment.
The signal chain of each inertial sensor (accelerometers and gyroscopes)
includes the application of unique correction formulas, which are derived from
extensive characterization of bias, sensitivity, alignment, response to linear
acceleration (gyroscopes), and point of percussion (accelerometer location)
over a temperature range of −40°C to +85°C, for each ADIS device. These
correction formulas are not accessible, but users do have the opportunity to
adjust the bias for each sensor individually through the calibbias attribute.
Each IIO device, has a device folder under ``/sys/bus/iio/devices/iio:deviceX``,
where X is the IIO index of the device. Under these folders reside a set of
device files, depending on the characteristics and features of the hardware
device in questions. These files are consistently generalized and documented in
the IIO ABI documentation.
The following tables show the adis16475 related device files, found in the
specific device folder path ``/sys/bus/iio/devices/iio:deviceX``.
+-------------------------------------------+----------------------------------------------------------+
| 3-Axis Accelerometer related device files | Description |
+-------------------------------------------+----------------------------------------------------------+
| in_accel_scale | Scale for the accelerometer channels. |
+-------------------------------------------+----------------------------------------------------------+
| in_accel_x_calibbias | Calibration offset for the X-axis accelerometer channel. |
+-------------------------------------------+----------------------------------------------------------+
| in_accel_x_raw | Raw X-axis accelerometer channel value. |
+-------------------------------------------+----------------------------------------------------------+
| in_accel_y_calibbias | Calibration offset for the Y-axis accelerometer channel. |
+-------------------------------------------+----------------------------------------------------------+
| in_accel_y_raw | Raw Y-axis accelerometer channel value. |
+-------------------------------------------+----------------------------------------------------------+
| in_accel_z_calibbias | Calibration offset for the Z-axis accelerometer channel. |
+-------------------------------------------+----------------------------------------------------------+
| in_accel_z_raw | Raw Z-axis accelerometer channel value. |
+-------------------------------------------+----------------------------------------------------------+
| in_deltavelocity_scale | Scale for delta velocity channels. |
+-------------------------------------------+----------------------------------------------------------+
| in_deltavelocity_x_raw | Raw X-axis delta velocity channel value. |
+-------------------------------------------+----------------------------------------------------------+
| in_deltavelocity_y_raw | Raw Y-axis delta velocity channel value. |
+-------------------------------------------+----------------------------------------------------------+
| in_deltavelocity_z_raw | Raw Z-axis delta velocity channel value. |
+-------------------------------------------+----------------------------------------------------------+
+---------------------------------------+------------------------------------------------------+
| 3-Axis Gyroscope related device files | Description |
+---------------------------------------+------------------------------------------------------+
| in_anglvel_scale | Scale for the gyroscope channels. |
+---------------------------------------+------------------------------------------------------+
| in_anglvel_x_calibbias | Calibration offset for the X-axis gyroscope channel. |
+---------------------------------------+------------------------------------------------------+
| in_anglvel_x_raw | Raw X-axis gyroscope channel value. |
+---------------------------------------+------------------------------------------------------+
| in_anglvel_y_calibbias | Calibration offset for the Y-axis gyroscope channel. |
+---------------------------------------+------------------------------------------------------+
| in_anglvel_y_raw | Raw Y-axis gyroscope channel value. |
+---------------------------------------+------------------------------------------------------+
| in_anglvel_z_calibbias | Calibration offset for the Z-axis gyroscope channel. |
+---------------------------------------+------------------------------------------------------+
| in_anglvel_z_raw | Raw Z-axis gyroscope channel value. |
+---------------------------------------+------------------------------------------------------+
| in_deltaangl_scale | Scale for delta angle channels. |
+---------------------------------------+------------------------------------------------------+
| in_deltaangl_x_raw | Raw X-axis delta angle channel value. |
+---------------------------------------+------------------------------------------------------+
| in_deltaangl_y_raw | Raw Y-axis delta angle channel value. |
+---------------------------------------+------------------------------------------------------+
| in_deltaangl_z_raw | Raw Z-axis delta angle channel value. |
+---------------------------------------+------------------------------------------------------+
+----------------------------------+-------------------------------------------+
| Temperature sensor related files | Description |
+----------------------------------+-------------------------------------------+
| in_temp0_raw | Raw temperature channel value. |
+----------------------------------+-------------------------------------------+
| in_temp0_scale | Scale for the temperature sensor channel. |
+----------------------------------+-------------------------------------------+
+-------------------------------+---------------------------------------------------------+
| Miscellaneous device files | Description |
+-------------------------------+---------------------------------------------------------+
| name | Name of the IIO device. |
+-------------------------------+---------------------------------------------------------+
| sampling_frequency | Currently selected sample rate. |
+-------------------------------+---------------------------------------------------------+
| filter_low_pass_3db_frequency | Bandwidth for the accelerometer and gyroscope channels. |
+-------------------------------+---------------------------------------------------------+
The following table shows the adis16475 related device debug files, found in the
specific device debug folder path ``/sys/kernel/debug/iio/iio:deviceX``.
+----------------------+-------------------------------------------------------------------------+
| Debugfs device files | Description |
+----------------------+-------------------------------------------------------------------------+
| serial_number | The serial number of the chip in hexadecimal format. |
+----------------------+-------------------------------------------------------------------------+
| product_id | Chip specific product id (e.g. 16475, 16500, 16505, etc.). |
+----------------------+-------------------------------------------------------------------------+
| flash_count | The number of flash writes performed on the device. |
+----------------------+-------------------------------------------------------------------------+
| firmware_revision | String containing the firmware revision in the following format ##.##. |
+----------------------+-------------------------------------------------------------------------+
| firmware_date | String containing the firmware date in the following format mm-dd-yyyy. |
+----------------------+-------------------------------------------------------------------------+
Channels processed values
-------------------------
A channel value can be read from its _raw attribute. The value returned is the
raw value as reported by the devices. To get the processed value of the channel,
apply the following formula:
.. code-block:: bash
processed value = (_raw + _offset) * _scale
Where _offset and _scale are device attributes. If no _offset attribute is
present, simply assume its value is 0.
The adis16475 driver offers data for 5 types of channels, the table below shows
the measurement units for the processed value, which are defined by the IIO
framework:
+-------------------------------------+---------------------------+
| Channel type | Measurement unit |
+-------------------------------------+---------------------------+
| Acceleration on X, Y, and Z axis | Meters per Second squared |
+-------------------------------------+---------------------------+
| Angular velocity on X, Y and Z axis | Radians per second |
+-------------------------------------+---------------------------+
| Delta velocity on X. Y, and Z axis | Meters per Second |
+-------------------------------------+---------------------------+
| Delta angle on X, Y, and Z axis | Radians |
+-------------------------------------+---------------------------+
| Temperature | Millidegrees Celsius |
+-------------------------------------+---------------------------+
Usage examples
--------------
Show device name:
.. code-block:: bash
root:/sys/bus/iio/devices/iio:device0> cat name
adis16505-2
Show accelerometer channels value:
.. code-block:: bash
root:/sys/bus/iio/devices/iio:device0> cat in_accel_x_raw
-275924
root:/sys/bus/iio/devices/iio:device0> cat in_accel_y_raw
-30142222
root:/sys/bus/iio/devices/iio:device0> cat in_accel_z_raw
261265769
root:/sys/bus/iio/devices/iio:device0> cat in_accel_scale
0.000000037
- X-axis acceleration = in_accel_x_raw * in_accel_scale = −0.010209188 m/s^2
- Y-axis acceleration = in_accel_y_raw * in_accel_scale = −1.115262214 m/s^2
- Z-axis acceleration = in_accel_z_raw * in_accel_scale = 9.666833453 m/s^2
Show gyroscope channels value:
.. code-block:: bash
root:/sys/bus/iio/devices/iio:device0> cat in_anglvel_x_raw
-3324626
root:/sys/bus/iio/devices/iio:device0> cat in_anglvel_y_raw
1336980
root:/sys/bus/iio/devices/iio:device0> cat in_anglvel_z_raw
-602983
root:/sys/bus/iio/devices/iio:device0> cat in_anglvel_scale
0.000000006
- X-axis angular velocity = in_anglvel_x_raw * in_anglvel_scale = −0.019947756 rad/s
- Y-axis angular velocity = in_anglvel_y_raw * in_anglvel_scale = 0.00802188 rad/s
- Z-axis angular velocity = in_anglvel_z_raw * in_anglvel_scale = −0.003617898 rad/s
Set calibration offset for accelerometer channels:
.. code-block:: bash
root:/sys/bus/iio/devices/iio:device0> cat in_accel_x_calibbias
0
root:/sys/bus/iio/devices/iio:device0> echo 5000 > in_accel_x_calibbias
root:/sys/bus/iio/devices/iio:device0> cat in_accel_x_calibbias
5000
Set calibration offset for gyroscope channels:
.. code-block:: bash
root:/sys/bus/iio/devices/iio:device0> cat in_anglvel_y_calibbias
0
root:/sys/bus/iio/devices/iio:device0> echo -5000 > in_anglvel_y_calibbias
root:/sys/bus/iio/devices/iio:device0> cat in_anglvel_y_calibbias
-5000
Set sampling frequency:
.. code-block:: bash
root:/sys/bus/iio/devices/iio:device0> cat sampling_frequency
2000.000000
root:/sys/bus/iio/devices/iio:device0> echo 1000 > sampling_frequency
1000.000000
Set bandwidth for accelerometer and gyroscope:
.. code-block:: bash
root:/sys/bus/iio/devices/iio:device0> cat filter_low_pass_3db_frequency
720
root:/sys/bus/iio/devices/iio:device0> echo 360 > filter_low_pass_3db_frequency
root:/sys/bus/iio/devices/iio:device0> cat filter_low_pass_3db_frequency
360
Show serial number:
.. code-block:: bash
root:/sys/kernel/debug/iio/iio:device0> cat serial_number
0x04f9
Show product id:
.. code-block:: bash
root:/sys/kernel/debug/iio/iio:device0> cat product_id
16505
Show flash count:
.. code-block:: bash
root:/sys/kernel/debug/iio/iio:device0> cat flash_count
150
Show firmware revision:
.. code-block:: bash
root:/sys/kernel/debug/iio/iio:device0> cat firmware_revision
1.6
Show firmware date:
.. code-block:: bash
root:/sys/kernel/debug/iio/iio:device0> cat firmware_date
06-27-2019
3. Device buffers
=================
This driver supports IIO buffers.
All devices support retrieving the raw acceleration, gyroscope and temperature
measurements using buffers.
The following device families also support retrieving the delta velocity, delta
angle and temperature measurements using buffers:
- ADIS16477
- ADIS16500
- ADIS16505
- ADIS16507
However, when retrieving acceleration or gyroscope data using buffers, delta
readings will not be available and vice versa.
Usage examples
--------------
Set device trigger in current_trigger, if not already set:
.. code-block:: bash
root:/sys/bus/iio/devices/iio:device0> cat trigger/current_trigger
root:/sys/bus/iio/devices/iio:device0> echo adis16505-2-dev0 > trigger/current_trigger
root:/sys/bus/iio/devices/iio:device0> cat trigger/current_trigger
adis16505-2-dev0
Select channels for buffer read:
.. code-block:: bash
root:/sys/bus/iio/devices/iio:device0> echo 1 > scan_elements/in_deltavelocity_x_en
root:/sys/bus/iio/devices/iio:device0> echo 1 > scan_elements/in_deltavelocity_y_en
root:/sys/bus/iio/devices/iio:device0> echo 1 > scan_elements/in_deltavelocity_z_en
root:/sys/bus/iio/devices/iio:device0> echo 1 > scan_elements/in_temp0_en
Set the number of samples to be stored in the buffer:
.. code-block:: bash
root:/sys/bus/iio/devices/iio:device0> echo 10 > buffer/length
Enable buffer readings:
.. code-block:: bash
root:/sys/bus/iio/devices/iio:device0> echo 1 > buffer/enable
Obtain buffered data:
.. code-block:: bash
root:/sys/bus/iio/devices/iio:device0> hexdump -C /dev/iio\:device0
...
00001680 01 1f 00 00 ff ff fe ef 00 00 47 bf 00 03 35 55 |..........G...5U|
00001690 01 1f 00 00 ff ff ff d9 00 00 46 f1 00 03 35 35 |..........F...55|
000016a0 01 1f 00 00 ff ff fe fc 00 00 46 cb 00 03 35 7b |..........F...5{|
000016b0 01 1f 00 00 ff ff fe 41 00 00 47 0d 00 03 35 8b |.......A..G...5.|
000016c0 01 1f 00 00 ff ff fe 37 00 00 46 b4 00 03 35 90 |.......7..F...5.|
000016d0 01 1d 00 00 ff ff fe 5a 00 00 45 d7 00 03 36 08 |.......Z..E...6.|
000016e0 01 1b 00 00 ff ff fe fb 00 00 45 e7 00 03 36 60 |..........E...6`|
000016f0 01 1a 00 00 ff ff ff 17 00 00 46 bc 00 03 36 de |..........F...6.|
00001700 01 1a 00 00 ff ff fe 59 00 00 46 d7 00 03 37 b8 |.......Y..F...7.|
00001710 01 1a 00 00 ff ff fe ae 00 00 46 95 00 03 37 ba |..........F...7.|
00001720 01 1a 00 00 ff ff fe c5 00 00 46 63 00 03 37 9f |..........Fc..7.|
00001730 01 1a 00 00 ff ff fe 55 00 00 46 89 00 03 37 c1 |.......U..F...7.|
00001740 01 1a 00 00 ff ff fe 31 00 00 46 aa 00 03 37 f7 |.......1..F...7.|
...
See ``Documentation/iio/iio_devbuf.rst`` for more information about how buffered
data is structured.
4. IIO Interfacing Tools
========================
See ``Documentation/iio/iio_tools.rst`` for the description of the available IIO
interfacing tools.
|
