| Age | Commit message (Collapse) | Author | Files | Lines |
|---|
|
The continual trickle of small conversion patches is grating on me, and
is really not helping. Just get rid of the 'remove_new' member
function, which is just an alias for the plain 'remove', and had a
comment to that effect:
/*
* .remove_new() is a relic from a prototype conversion of .remove().
* New drivers are supposed to implement .remove(). Once all drivers are
* converted to not use .remove_new any more, it will be dropped.
*/
This was just a tree-wide 'sed' script that replaced '.remove_new' with
'.remove', with some care taken to turn a subsequent tab into two tabs
to make things line up.
I did do some minimal manual whitespace adjustment for places that used
spaces to line things up.
Then I just removed the old (sic) .remove_new member function, and this
is the end result. No more unnecessary conversion noise.
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
|
|
The AMD Legacy I3C is having a problem with its IP, specifically with the
push-pull and open-drain pull-up registers. These registers need to be
manually programmed for every CCC submission to align with the duty cycle.
Therefore, add a quirk to address this issue.
Reviewed-by: Jarkko Nikula <jarkko.nikula@linux.intel.com>
Co-developed-by: Sanket Goswami <Sanket.Goswami@amd.com>
Signed-off-by: Sanket Goswami <Sanket.Goswami@amd.com>
Signed-off-by: Shyam Sundar S K <Shyam-sundar.S-k@amd.com>
Link: https://lore.kernel.org/r/20241114110239.660551-3-Shyam-sundar.S-k@amd.com
Signed-off-by: Alexandre Belloni <alexandre.belloni@bootlin.com>
|
|
Add AMDI0015 _HID for Designware I3C driver so that the dw-i3c-master
driver can be probed on AMD platforms.
Reviewed-by: Jarkko Nikula <jarkko.nikula@linux.intel.com>
Signed-off-by: Shyam Sundar S K <Shyam-sundar.S-k@amd.com>
Link: https://lore.kernel.org/r/20241114110239.660551-2-Shyam-sundar.S-k@amd.com
Signed-off-by: Alexandre Belloni <alexandre.belloni@bootlin.com>
|
|
Add support for runtime and system power management.
Handle clocks, resets, pads as part of suspend and resume.
Restore controller registers that could be lost due to suspend.
Finally add get and put calls appropriately in functions which
access controller : bus_init, do_daa, send_ccc_cmd, priv_xfers,
i2c_xfers, ibi and hot-join.
Signed-off-by: Aniket <aniketmaurya@google.com>
Link: https://lore.kernel.org/r/20240708062103.3296587-4-aniketmaurya@google.com
Signed-off-by: Alexandre Belloni <alexandre.belloni@bootlin.com>
|
|
Separate logic for setting intr/thld registers in a func.
Also modify enable function to take care of setting all fields in DEVICE_CTRL.
These functions can be reused later for power management.
Signed-off-by: Aniket <aniketmaurya@google.com>
Link: https://lore.kernel.org/r/20240708062103.3296587-3-aniketmaurya@google.com
Signed-off-by: Alexandre Belloni <alexandre.belloni@bootlin.com>
|
|
Add variables to store timing registers and other values.
These variables would be later used to restore registers
during resume without recomputation.
Signed-off-by: Aniket <aniketmaurya@google.com>
Link: https://lore.kernel.org/r/20240708062103.3296587-2-aniketmaurya@google.com
Signed-off-by: Alexandre Belloni <alexandre.belloni@bootlin.com>
|
|
Besides the core clock, IP also has an apb interface clock.
Add an optional hook for the same.
Signed-off-by: Aniket <aniketmaurya@google.com>
Link: https://lore.kernel.org/r/20240628154618.327151-1-aniketmaurya@google.com
Signed-off-by: Alexandre Belloni <alexandre.belloni@bootlin.com>
|
|
Move to "enabled" variant of clk_get API. It takes care
of enable and disable calls during the probe and remove.
Signed-off-by: Aniket <aniketmaurya@google.com>
Link: https://lore.kernel.org/r/20240628154603.326075-1-aniketmaurya@google.com
Signed-off-by: Alexandre Belloni <alexandre.belloni@bootlin.com>
|
|
Since DW I3C IP master role always supports IBI, we don't need
to keep two variants of master ops and select one using this
property. Hence remove the code.
Signed-off-by: Aniket <aniketmaurya@google.com>
Link: https://lore.kernel.org/r/20240627034119.3938050-1-aniketmaurya@google.com
Signed-off-by: Alexandre Belloni <alexandre.belloni@bootlin.com>
|
|
IBI_SIR_REQ_REJECT register is not present if the IP has
IC_HAS_IBI_DATA = 1 set. So don't rely on doing read-
modify-write op on this register.
Instead maintain a variable to store the sir reject mask
and use it to set IBI_SIR_REQ_REJECT.
Signed-off-by: Aniket <aniketmaurya@google.com>
Reviewed-by: Jeremy Kerr <jk@codeconstruct.com.au>
Signed-off-by: Alexandre Belloni <alexandre.belloni@bootlin.com>
|
|
QUEUE_THLD_CTRL_IBI_STAT_MASK is repeated twice.
Replace with QUEUE_THLD_CTRL_IBI_DATA_MASK.
Signed-off-by: Aniket <aniketmaurya@google.com>
Signed-off-by: Alexandre Belloni <alexandre.belloni@bootlin.com>
|
|
Add hot-join support for dw i3c master controller.
By default, the hot-join acknowledgment is disabled, and the hardware will
automatically send the DISEC CCC when it receives the hot-join request.
Users can use the sys entry to enable it.
Signed-off-by: Billy Tsai <billy_tsai@aspeedtech.com>
Link: https://lore.kernel.org/r/20240429073624.256830-1-billy_tsai@aspeedtech.com
Signed-off-by: Alexandre Belloni <alexandre.belloni@bootlin.com>
|
|
Disable IBI IRQ signal and status only when hot-join and SIR enabling of
all target devices attached to the bus are disabled.
Fixes: e389b1d72a62 ("i3c: dw: Add support for in-band interrupts")
Signed-off-by: Dylan Hung <dylan_hung@aspeedtech.com>
Link: https://lore.kernel.org/r/20240119054547.983693-1-dylan_hung@aspeedtech.com
Signed-off-by: Alexandre Belloni <alexandre.belloni@bootlin.com>
|
|
Prepare for the coming implementation by GCC and Clang of the __counted_by
attribute. Flexible array members annotated with __counted_by can have
their accesses bounds-checked at run-time checking via CONFIG_UBSAN_BOUNDS
(for array indexing) and CONFIG_FORTIFY_SOURCE (for strcpy/memcpy-family
functions).
As found with Coccinelle[1], add __counted_by for struct dw_i3c_xfer.
[1] https://github.com/kees/kernel-tools/blob/trunk/coccinelle/examples/counted_by.cocci
Cc: Alexandre Belloni <alexandre.belloni@bootlin.com>
Cc: Jeremy Kerr <jk@codeconstruct.com.au>
Cc: Joel Stanley <joel@jms.id.au>
Cc: linux-i3c@lists.infradead.org
Signed-off-by: Kees Cook <keescook@chromium.org>
Reviewed-by: Gustavo A. R. Silva <gustavoars@kernel.org>
Reviewed-by: Jeremy Kerr <jk@codeconstruct.com.au>
Link: https://lore.kernel.org/r/20230922175011.work.800-kees@kernel.org
Signed-off-by: Alexandre Belloni <alexandre.belloni@bootlin.com>
|
|
On the AST2600 i3c controller, we'll need to apply a workaround for a
hardware issue with IBI payloads.
Introduce a platform hook to allow dw i3c platform implementations to
modify the DAT entry in IBI enable/disable to allow this workaround in a
future change.
Signed-off-by: Jeremy Kerr <jk@codeconstruct.com.au>
Reviewed-by: Joel Stanley <joel@jms.id.au>
Link: https://lore.kernel.org/r/d5d76a8d2336d2a71886537f42e71d51db184df6.1680161823.git.jk@codeconstruct.com.au
Signed-off-by: Alexandre Belloni <alexandre.belloni@bootlin.com>
|
|
This change adds support for receiving and dequeueing i3c IBIs.
By setting struct dw_i3c_master->ibi_capable before probe, a platform
implementation can select the IBI-enabled version of the i3c_master_ops,
enabling the global IBI infrastrcture for that controller.
Signed-off-by: Jeremy Kerr <jk@codeconstruct.com.au>
Reviewed-by: Joel Stanley <joel@jms.id.au>
Link: https://lore.kernel.org/r/79daeefd7ccb7c935d0c159149df21a6c9a73ffa.1680161823.git.jk@codeconstruct.com.au
Signed-off-by: Alexandre Belloni <alexandre.belloni@bootlin.com>
|
|
In an upcoming change, we will want to store additional data about the
devices we have in the data address table.
Change the type of the DAT entries into a struct, which currently just
has the address data.
Signed-off-by: Jeremy Kerr <jk@codeconstruct.com.au>
Reviewed-by: Joel Stanley <joel@jms.id.au>
Link: https://lore.kernel.org/r/9dc0d9e2857e851a0cf04819df48e5d31921f83e.1680161823.git.jk@codeconstruct.com.au
Signed-off-by: Alexandre Belloni <alexandre.belloni@bootlin.com>
|
|
In a future change we'll want to read from the IBI FIFO too, so turn
dw_i3c_read_rx_fifo() into a generic read with the FIFO register as a
parameter.
Signed-off-by: Jeremy Kerr <jk@codeconstruct.com.au>
Reviewed-by: Joel Stanley <joel@jms.id.au>
Link: https://lore.kernel.org/r/827204789583dd86addffb47ecaeab9d67cf95d5.1680161823.git.jk@codeconstruct.com.au
Signed-off-by: Alexandre Belloni <alexandre.belloni@bootlin.com>
|
|
The dw i3c core can be integrated into various SoC devices. Platforms
that use this core may need a little configuration that is specific to
that platform.
Add some infrastructure to allow platform-specific behaviour: common
probe/remove functions, a set of platform hook operations, and a pointer
for platform-specific data in struct dw_i3c_master. Move the common api
into a new (i3c local) header file.
Platforms will provide their own struct platform_driver, which allocates
struct dw_i3c_master, does any platform-specific probe behaviour, and
calls into the common probe.
A future change will add new platform support that uses this
infrastructure.
Signed-off-by: Jeremy Kerr <jk@codeconstruct.com.au>
Reviewed-by: Joel Stanley <joel@jms.id.au>
Link: https://lore.kernel.org/r/20230331091501.3800299-2-jk@codeconstruct.com.au
Signed-off-by: Alexandre Belloni <alexandre.belloni@bootlin.com>
|
|
In the clock setup path, we set the hardware DEV_CTRL_I2C_SLAVE_PRESENT
bit on a shared mode bus, then read-back this bit for the conditional
tCAS set.
Instead, just use the bus->mode setting for the conditional test.
While we're at it, add a little comment about why the conditional is
there.
Signed-off-by: Jeremy Kerr <jk@codeconstruct.com.au>
Link: https://lore.kernel.org/r/92a933566f7846708a00ad7f5a16ee8e6ed32d0e.1680156630.git.jk@codeconstruct.com.au
Signed-off-by: Alexandre Belloni <alexandre.belloni@bootlin.com>
|
|
We currently assume that the rx_len of a read command will be as
submitted, but we may have a shorter read than expected.
This change populates the output i3c xfer length from the actually-read
length.
Signed-off-by: Matt Johnston <matt@codeconstruct.com.au>
Signed-off-by: Jeremy Kerr <jk@codeconstruct.com.au>
Link: https://lore.kernel.org/r/f4fff7ab18dee1f662dc7a5a4111fcd921e6792b.1680156630.git.jk@codeconstruct.com.au
Signed-off-by: Alexandre Belloni <alexandre.belloni@bootlin.com>
|
|
The .remove() callback for a platform driver returns an int which makes
many driver authors wrongly assume it's possible to do error handling by
returning an error code. However the value returned is (mostly) ignored
and this typically results in resource leaks. To improve here there is a
quest to make the remove callback return void. In the first step of this
quest all drivers are converted to .remove_new() which already returns
void.
Trivially convert this driver from always returning zero in the remove
callback to the void returning variant.
Signed-off-by: Uwe Kleine-König <u.kleine-koenig@pengutronix.de>
Link: https://lore.kernel.org/r/20230318233311.265186-3-u.kleine-koenig@pengutronix.de
Signed-off-by: Alexandre Belloni <alexandre.belloni@bootlin.com>
|
|
The function returned zero unconditionally. Switch the return type to void
and simplify the callers accordingly.
Signed-off-by: Uwe Kleine-König <u.kleine-koenig@pengutronix.de>
Reviewed-by: Miquel Raynal <miquel.raynal@bootlin.com>
Link: https://lore.kernel.org/r/20230318233311.265186-2-u.kleine-koenig@pengutronix.de
Signed-off-by: Alexandre Belloni <alexandre.belloni@bootlin.com>
|
|
The driver can match only via the DT table so the table should be always
used and the of_match_ptr does not have any sense (this also allows ACPI
matching via PRP0001, even though it might not be relevant here). This
also fixes !CONFIG_OF error:
drivers/i3c/master/dw-i3c-master.c:1201:34: error: ‘dw_i3c_master_of_match’ defined but not used [-Werror=unused-const-variable=]
Signed-off-by: Krzysztof Kozlowski <krzysztof.kozlowski@linaro.org>
Link: https://lore.kernel.org/r/20230312132535.352246-1-krzysztof.kozlowski@linaro.org
Signed-off-by: Alexandre Belloni <alexandre.belloni@bootlin.com>
|
|
Bus-speed could be default(12.5MHz) or defined by users in dts.
Dw-i3c-master should not hard-code the initial speed to be
I3C_BUS_TYP_I3C_SCL_RATE (12.5MHz)
And because of Synopsys's I3C controller limit (hcnt/lcnt register
length) and core-clk provided, there is a limit to bus speed, too.
For example, when core-clk is 250 MHz, the bus speed cannot be
lowered below 1MHz.
Tested: tested with an i3c sensor and captured with a logic analyzer.
Signed-off-by: Jack Chen <zenghuchen@google.com>
Link: https://lore.kernel.org/r/20230216151057.293764-1-zenghuchen@google.com
Signed-off-by: Alexandre Belloni <alexandre.belloni@bootlin.com>
|
|
Clang static analysis reports this problem
dw-i3c-master.c:799:9: warning: The result of the left shift is
undefined because the left operand is negative
COMMAND_PORT_DEV_INDEX(pos) |
^~~~~~~~~~~~~~~~~~~~~~~~~~~
pos can be negative because dw_i3c_master_get_free_pos() can return an
error. So check for an error.
Fixes: 1dd728f5d4d4 ("i3c: master: Add driver for Synopsys DesignWare IP")
Signed-off-by: Tom Rix <trix@redhat.com>
Signed-off-by: Alexandre Belloni <alexandre.belloni@bootlin.com>
Link: https://lore.kernel.org/r/20220108150948.3988790-1-trix@redhat.com
|
|
Disabling all event calls is already handled by the core right before
starting the DAA process. Do not do it again when the DAA process
completes, it is redundant.
Fixes: 1dd728f5d4d4 ("i3c: master: Add driver for Synopsys DesignWare IP")
Signed-off-by: Miquel Raynal <miquel.raynal@bootlin.com>
Signed-off-by: Alexandre Belloni <alexandre.belloni@bootlin.com>
Link: https://lore.kernel.org/r/20201228105501.6104-1-miquel.raynal@bootlin.com
|
|
Replace the existing /* fall through */ comments and its variants with
the new pseudo-keyword macro fallthrough[1]. Also, remove unnecessary
fall-through markings when it is the case.
[1] https://www.kernel.org/doc/html/v5.7/process/deprecated.html?highlight=fallthrough#implicit-switch-case-fall-through
Signed-off-by: Gustavo A. R. Silva <gustavoars@kernel.org>
|
|
The current codebase makes use of the zero-length array language
extension to the C90 standard, but the preferred mechanism to declare
variable-length types such as these ones is a flexible array member[1][2],
introduced in C99:
struct foo {
int stuff;
struct boo array[];
};
By making use of the mechanism above, we will get a compiler warning
in case the flexible array does not occur last in the structure, which
will help us prevent some kind of undefined behavior bugs from being
inadvertently introduced[3] to the codebase from now on.
Also, notice that, dynamic memory allocations won't be affected by
this change:
"Flexible array members have incomplete type, and so the sizeof operator
may not be applied. As a quirk of the original implementation of
zero-length arrays, sizeof evaluates to zero."[1]
This issue was found with the help of Coccinelle.
[1] https://gcc.gnu.org/onlinedocs/gcc/Zero-Length.html
[2] https://github.com/KSPP/linux/issues/21
[3] commit 76497732932f ("cxgb3/l2t: Fix undefined behaviour")
Signed-off-by: Gustavo A. R. Silva <gustavo@embeddedor.com>
Signed-off-by: Boris Brezillon <boris.brezillon@collabora.com>
Link: https://lore.kernel.org/linux-i3c/20200227131307.GA24935@embeddedor
|
|
For today the reattach function only update the device address on the
controller.
Update the location to the first available too, will optimize the
enumeration process avoiding additional checks to keep the available
positions on address table consecutive.
Signed-off-by: Vitor Soares <vitor.soares@synopsys.com>
Reviewed-by: Boris Brezillon <boris.brezillon@collabora.com>
Signed-off-by: Boris Brezillon <boris.brezillon@collabora.com>
|
|
Use devm_platform_ioremap_resource() to simplify code.
Signed-off-by: Yangtao Li <tiny.windzz@gmail.com>
Acked-by: Vitor Soares <vitor.soares@synopsys.com>
Signed-off-by: Boris Brezillon <boris.brezillon@collabora.com>
|
|
I need to store address and lvr value for I2C devices without static definition
in DT. This allows secondary master to transmit DEFSLVS command properly.
Main changes between v4 and v5:
- Change in defslvs to use addr and lvr from i2c_dev_desc structure
- Change in CDNS and DW drivers to use addr and lvr from i2c_dev_desc structure
Signed-off-by: Przemyslaw Gaj <pgaj@cadence.com>
Signed-off-by: Boris Brezillon <boris.brezillon@collabora.com>
|
|
This patch add limited bus mode support for DesignWare i3c master
Signed-off-by: Vitor Soares <vitor.soares@synopsys.com>
Cc: Boris Brezillon <bbrezillon@kernel.org>
Cc: <linux-kernel@vger.kernel.org>
Signed-off-by: Boris Brezillon <boris.brezillon@collabora.com>
|
|
This patch drops support for I2C devices with 10 bit addressing. When I2C
device with 10 bit address is defined in DT, I3C master registration fails.
Address space for I2C devices has been reduced and ->i2c_funcs() hook has been
removed.
Because this patch series dropped support for 10 bit I2C devices, support is
also dropped in Cadence I3C master driver and Synopsys DesignWare I3C master
driver.
Signed-off-by: Przemyslaw Gaj <pgaj@cadence.com>
Signed-off-by: Boris Brezillon <boris.brezillon@collabora.com>
|
|
git://git.kernel.org/pub/scm/linux/kernel/git/i3c/linux
Pull i3c update from Boris Brezillon:
- Fix a shift wrap bug in the core
- Remove dead code in the DW driver
* tag 'i3c/for-5.2' of git://git.kernel.org/pub/scm/linux/kernel/git/i3c/linux:
i3c: Fix a shift wrap bug in i3c_bus_set_addr_slot_status()
i3c: master: dw: remove dead code from dw_i3c_master_*_xfers()
|
|
The controller was being disabled incorrectly. The correct way is to clear
the DEV_CTRL_ENABLE bit.
Fix this by clearing this bit.
Cc: Boris Brezillon <bbrezillon@kernel.org>
Cc: <stable@vger.kernel.org>
Fixes: 1dd728f5d4d4 ("i3c: master: Add driver for Synopsys DesignWare IP")
Signed-off-by: Vitor Soares <vitor.soares@synopsys.com>
Signed-off-by: Boris Brezillon <boris.brezillon@collabora.com>
|
|
Detected by CoverityScan (Event result_independent_of_operands):
"(i3c_xfers + i).len > 65536" is always false regardless of the values
of its operands. This occurs as the logical operand of "if"
"(i2c_xfers + i).len > 65536" is always false regardless of the values
of its operands. This occurs as the logical operand of "if"
Signed-off-by: Vitor Soares <vitor.soares@synopsys.com>
Signed-off-by: Boris Brezillon <boris.brezillon@collabora.com>
|
|
git://git.kernel.org/pub/scm/linux/kernel/git/i3c/linux
Pull i3c updates from Boris Brezillon:
- Add a /* fall-through */ comment in the dw-i3c-master driver
- Update the I3C entries in MAINTAINERS to add an IRC chan
* tag 'i3c/for-5.1' of git://git.kernel.org/pub/scm/linux/kernel/git/i3c/linux:
i3c: master: dw-i3c-master: mark expected switch fall-through
MAINTAINERS: Add an IRC channel for the I3C subsystem
|
|
In preparation to enabling -Wimplicit-fallthrough, mark switch
cases where we are expecting to fall through.
This patch fixes the following warning:
drivers/i3c/master/dw-i3c-master.c: In function ‘dw_i3c_master_bus_init’:
drivers/i3c/master/dw-i3c-master.c:603:6: warning: this statement may fall through [-Wimplicit-fallthrough=]
if (ret)
^
drivers/i3c/master/dw-i3c-master.c:605:2: note: here
case I3C_BUS_MODE_PURE:
^~~~
Warning level 3 was used: -Wimplicit-fallthrough=3
This patch is part of the ongoing efforts to enable
-Wimplicit-fallthrough.
Signed-off-by: Gustavo A. R. Silva <gustavo@embeddedor.com>
Acked-by: Vitor Soares <vitor.soares@synopsys.com>
Signed-off-by: Boris Brezillon <boris.brezillon@collabora.com>
|
|
In dw_i3c_master_irq_handler(), we already have gotten
&master->xferqueue.lock, if we try to get the same lock again in
dw_i3c_master_dequeue_xfer(), deadlock happens.
We fix this issue by introduing dw_i3c_master_dequeue_xfer_locked()
which does all what dw_i3c_master_dequeue_xfer() does without trying
to lock &master->xferqueue.lock.
Signed-off-by: Jisheng Zhang <Jisheng.Zhang@synaptics.com>
Acked-by: Vitor Soares <vitor.soares@synopsys.com>
Signed-off-by: Boris Brezillon <bbrezillon@kernel.org>
|
|
This patch fix i3c_attach/reattach functions.
During the i3c_attach the driver ignores the static address used for
SETDASA CCC command.
During the i3c_reattach the driver doesn't update master->addrs[data->index]
with new address if old_dyn_addr = 0.
Fixes: 1dd728f5d4d4 ("i3c: master: Add driver for Synopsys DesignWare IP")
Signed-off-by: Vitor Soares <vitor.soares@synopsys.com>
Signed-off-by: Boris Brezillon <bbrezillon@kernel.org>
|
|
The masking operation on status is using a bitwise 'or' rather than
a bitwise 'and' operator, and hence the result is always non-zero
which is probably not what is intended. Fix this by using the correct
operator.
Detected by CoverityScan, CID#1475523 ("Wrong operator used")
Fixes: 88acc98a712a ("i3c: master: Add driver for Synopsys DesignWare IP")
Signed-off-by: Colin Ian King <colin.king@canonical.com>
Acked-by: Vitor Soares <vitor.soares@synopsys.com>
Signed-off-by: Boris Brezillon <boris.brezillon@bootlin.com>
|
|
Add driver for Synopsys DesignWare I3C master IP
Signed-off-by: Vitor Soares <vitor.soares@synopsys.com>
Signed-off-by: Boris Brezillon <boris.brezillon@bootlin.com>
|
